Similar Questions

• "The files are on a volume that does not support Trash. You want to permanently delete the item? »

  All of a sudden I started getting error "files are on a volume that does not support Trash. You want to permanently delete the item?

  iMAC OSX 10.9.4.

  LR 5.6.

  Camara 8.6 gross

  Any idea?

  Please help me...

  Thanks in advance

  Jose

  It's quite common - there are several discussions about this.

  Simplest solution is to an empty folder on the disc, and drag it to the trash. LR will then work until you restart. You can empty the trash or not. Don't forget to make a different folder when you restart the computer.

• Move to the new computer, get "an error has occurred during playback of files or write files to a disk." The disc

  • I tried to move my catalog and PE6 install to a new computer.  This is on a Dell Windows XP machine, and I moved it to a Toshiba Windows 7 (64-bit) machine.  I always kept my photo on an external hard drive files.  My library is 50 GB, 10,000 files.  Here's what I did.
    • Copied the original PE6 installation file on the Toshiba.  Installed but not activate it.
    • Copied my catalog folder to the location of the Windows 7.
    • Plug the external drive into the Toshiba.  So makes that same letter drive as a front.
    • Fired up to PE6 on Toshiba.  Seemed fine in the Organizer.  Everything seemed to be there, but I didn't try to make any changes at this time there.
    • PE6 disabled on the Dell.  Enabled on the Toshiba.
  • Then I realized that it is not fair.  I can edit the keywords and the stars rating on photos, but not the dates, legends or notes.  I get "an error has occurred during playback of files or write files to a disk." The drive is may be full, or there may be problems with the source media. »
  • Only a fraction of the external drive is in use.
  • I can access the files on the external hard drive with another application (Windows Photo Viewer).
  • I tried the reconnect All missing files.  Somewhat ambiguous, she said "There are no files to reconnect."
  • In the properties in the organizer for each photo are the appropriate file names and paths.  Folder view works fine in the Organizer.
  • I can put new files in the directories of the same external drive, import them into PE6, then change them normally.

  What is the best way to get Organizer connected correctly to my files?  I guess I could import all photos on the new machine, but I guess I'd lose some of my metadata.  So it's out of the question.

  Thank you

  Bill

  Well, the recommended method for moving the catalog is to use organizer of the PSE6 on your old computer to do a full backup on your DHM.  (Which backs up the catalog and media files).  Then, on your new computer, open the Organizer PSE6 and restore from this backup.

  Your method seems logical, but...

  Ken

• HP steam: strange files in "C:\system volume information.

  I have re-installed Windows 8.1 on my HP net book successfully.

  I later discovered several large files in "C:\system volume information" with names that start with "{" and end by '} '. Are these relics of my re - install and can they be deleted safely?

  I don't know if they were present before the re-installation.

  Hello

  I would not delete them because they retain information for me to restore. If TOO big and TOO old, you can remove

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/how-do-i-delete-huge-files-from-system-volume/2d31b256-2cb6-486e-AF97-e6018f594581?auth=1

  Kind regards.

• Can I remove the old update files that have already been applied?

  Good evening! I just a quick may be a dumb question... when I've updated my computer, if I remove the before update... like when a service pack number, as for example I downloaded the number of service pack 2 What do I do with the number of the service pack 1? delete it?

  Depends on the operating system - Windows

  Please note this is only for Windows XP and is not on Vista or Windows 7

  Folders that have uninstall as part of the name (for example $NtUninstallKB282010$ who reside in C:\windows (hidden files) are window Hot difficulty updating folders/files) can be removed safely (providing ever, you wish to uninstall the updates). I recommend you leave these records for a period of at least one month to make sure that the update works correctly.

  These updates can be removed individually or together. To learn more about the update/s go on:
  http://support.Microsoft.com/kb/xxxxxx
  NB: XXXXXX = the actual number, not to mention the "Q" or "Ko."

  Once you have removed the uninstall folders/files, then go to control panel, add/remove programs. Select the title of the corresponding Windows fix on the folder/file of the patch you just deleted, and select Delete. You will get a Windows error. This is because you deleted the uninstall folder/files. Simply choose OK and the entry will be removed from the Add/Remove Programs list.

  Don't NOT delete the folder $ $hf_mig

  Cleaning after installation of SP2
  http://aumha.org/win5/a/sp2faq.php#after

  and/or

  XP SP3: Post Installation Cleanup
  http://aumha.NET/viewtopic.php?f=62&t=33827

  For Vista and Windows 7

  The update uninstall method in Windows Vista is quite different from that in Windows XP.

  Uninstaller for each update folder no longer exists in Vista and the uninstall information is stored by the Volume Shadow Copy service.

  After each update, Volume Shadow Copy service backup only the updated files.

  So with Vista, it's a differential backup, rather than a full backup files for uninstall
  in Windows XP.

  This safeguard mechanism is used to save disk space.

  So basically, you are unable to manually delete the uninstall it from the computer.

  TaurArian [MVP] 2005-2011 - Update Services

• Reading of interlaced scaling BAD video in the preview of files 2015.3

  Hello, working in first Pro 2015.3 blow us up the size of the video to any value, say 110% (to exclude boom to the shot or other).  While we make (in ALL preview format - they all have the same defect).  During playback, we get bands chunky of a coarse comb effect where fields are of course spread over a fast movement.  It looks like old fashioned gross low resolution scaling.  Here is a screenshot of instant pause the playback view, it shows part of the image at 100% is to say 1:1 pixel to the screen:

  

  Then, we step forward (or rear of a framework to get the view full resolution according to the natures/parked frame display.)  Then, the effect of coarse comb went and we see the software displaying a reasonable interpretation:

  

  See how the striping is much better.  That's what you'd naturally expect to see reading all the courses in your sequence of rendering, because you have A) full playback resolution and B) you have actually rendered images for preview files (even choose the preview format that actually matches camera codec) or even a format Prores422 HQ.

  But now in 2015.3 in our normal workflow for many years, we can not be satisfied that our work is acceptable for broadcast because he plays today back this feverish comb coarse, crude effect.  So now we have to discount or ignore what we see and make a movie out and play this movie in reading software (Quicktime Player or MXF reader) just to see if it IS OK.  This means that any work of self-QC in first became useless.  This also means that we can make our work for customer insight and look with the first client.

  WHAT CAN WE DO?

  NOTE, HOWEVER, if we don't make a preview of a file and so native playback (DALYS-100) with yellow bars on top, it's all THE FINE - no gross comb effect - that is, it is exactly the same as the frame step full resolution/render!

  How can this be?  How can we better than quality render rendered Max reading UN-rendered file?

  We have even exported and then imported a rendered movie file and same that reads with the same effect of coarse comb despite this new film now playing at the 100% level.  While any player left 3rd he plays well - that you expect it to be.

  This is non-rendus with Instant playback pause playback:

  

  Here is the scale factor:

  

  Here is the view of the timeline:

  

  Here are the current settings of the sequence:

  

  This machine is a MacPro 24-core OS 10.9.5 with an ATI Radeon HD of Mo 5770 1024 card.

  Exactly the same problem that happens on our other new 6-core MacPro with graphic AMD over-pants 500 3072 MB on El Capitan card (these are the guys that started with this complaint, that they cannot trust their work).  Of course after color correction, effects and subtitles, most of our sequences MUST be made... until we need to do?

  Some have reverted back to 2015.2 where it is is not a problem. 

  Concerning

  I think that one of our in-house editors found a work around for this bug. Try adding a layer of setting on the video that is resized. This seems to fix deinterlacing problems when scaling of images.

• Change the name of files and folders in data warehouses

  Is it safe while a virtual machine is running to change the name of the VMDK files and folders in a data store?

  I discovered that a VMS VMDK files have a different name for the virtual machine itself, then someone changed the name of the virtual machine after you have created the records

  I had to do it a few times, will try to document the process that I follow.  If you have many warehouses of data, then make a note of what data store, the machine is in.  The next step is to unregister the virtual machine from vCenter / ESXi

  Then, you need to enable SSH on your ESXi host

  Use Putty or something similar for you connect to the ESXi host

  Run the following commands (in italics)

  cd vmfs/volumes / that is, if the data store that contains the virtual computer is named datastore1 then you would run cd/vmfs/volumes/datastore1

  Then run ls to verify that the virtual machine file is here

  Rename the folder by using mv

  Change to the folder with cd

  Rename the nvram, vmsd, vmx and running again is to say the mv

  MV oldname.nvram newname.nvram

  MV oldname.vmsd newname.vmsd

  MV oldname.vmx newname.vmx
  

  MV 1234.hlog - oldname newname - 1234.hlog

  Rename the vmdk with vmkfstools EI oldname.vmdk newname.vmdk

  Edit the vmx with vi newname.vmx

  Replace references to oldname to newname in this file

  Register the virtual machine with the ESXi server and it should be OK

  This link gives more details and other methods VMware KB: rename a virtual machine and VMware ESXi and ESX records

• branching projects the playback bar options

  Make us some connections classes and wonder about how other users discussed navigation with branching. Captivate does not (as far as I can tell) users to customize it that slide the 'next' buttons 'back' on the playback bar will sail and the progress bar shows where the Viewer is going, not on each slide. With the projects ramifications, the lack of flexibility both of these features causes a huge problem: how to give viewers control over what they see and keep the order of the content of the way we've designed?

  Right now the only solution we have developed with is to hide the progress bar and the next/back buttons on the bar games and include 'back' and 'continue' buttons on some slides. This isn't an ideal solution, because the CC should be visible, and have buttons on the bottom of the screen makes it hidden by the CC, then put them pretty far up the, whose ruins just the Visual on a large number of slides.

  Am I missing a feature in captivate? If someone has found a way to work around this problem, I'd love to hear it!

  You put the CSS in the file assets/css/CPLibraryAll.css.

  The css is not there, add, is that the CSS is the example I posted. You do not need to have color in the css, I added it for a specific project.

  To activate the CC on and outside, you need create a tip action associated with a button to toggle the use of the CC. the "Toggle" action and choose "cpCmndCC" as the variable.

• There is workaround to get the playback mode by default when I start the software adobe reader DC?

  There is workaround to get the playback mode by default when I start the software adobe reader DC?

  Hi Keeperparma,

  There is no option in Acrobat reader to customize playback mode when you start the player, but you can configure for a specific file by using the "view original" feature of acrobat, but which apply only to this specific pdf.

  Kind regards

  Rahul

• Cannot convert Server 2008 R2 Machine get error: Instant The VSS cannot be stored, because there is not enough space on the source volumes or because the source computer does not all NTFS volumes. Error code: 2147754783 (0x8004231F).

  I have a couple of server 08 R2 machines where the P to V conversion fails.  I did some research and the problem seems to be related to the system reserved Partition that has 0% available 100 MB free space.  Conversion fails with the error below.

  VSS snapshots cannot be stored because there is not enough space on the source volumes or because the source computer has not all NTFS volumes. Error code:
  2147754783 (0x8004231F).

  
  

  Someone had this problem and came to the top with a solution or to get around?
  

  
  

  Thanks in advance
  

  Guessed it.  My snapshots Appassure did not also exist with a similar error, so that's what I did to solve it.  My servers now converted without any problem.

  1. Open disk management.
  2. Look at the partition of the PRS and see if it is 100% full.
     • If Yes, proceed to step 3.
     • If this is not the case, check if there are readers who have no more of 300 MB free (minimum requirement to use VSS).
  3. Click a drive, select properties and then select the instant snapshots tab.
  4. Ensure that all shadow copies are disabled and no limit on all players.
  5. Go to the partition of the SRP and assign the B:drive letter.
  6. Open the B: drive via disk management, and then locate the folder System Volume Information. Note: if necessary, change the folder options so that you can view hidden files, folders and drives.
  7. Right-click the System Volume Information folder, and then select Properties.
  8. On the Security tab, click Edit, and then add the group with full control everyone in the folder.
  9. Open the System Volume Information folder (you should see log files are full), open a running as an administrator command prompt and then type the following commands to unload the filter driver.
     • B:
     • B:\>FLTMC UNLOAD AAFSFLT
  10. Navigate to the System Volume Information folder, and then type the following commands:
      • B:\>CD System Volume Information
      • B:\System Volume Information > AALOG_ DEL * (this will remove all of the log files, and then re-create a new)
      • B:\System Volume Information > CD\
      • B:\>FLTMC LOAD AAFSFLT
  11. Close the command prompt window.
  12. In Windows, right click on the reserve system folder and remove the Group everyone.
  13. In Disk Manager, remove the B: drive (and click Yes when prompted with a warning window).

• Back to zero (or "Screw up") the Lightroom preferences file

  Hello

  in an effort to make the option change in the work of LR, I found the instructions I need to reset the LR preferences file. I followed the following, see below.

  However, even with pressing option key on my iMac, as indicated, I can't file and the file. I don't have a library folder under my user name, but only under the hard drive, and I can find the files com.adobe.photoshop, but no files in LR. Can someone help me?

  Lightroom help .

  Preference and other locations of files in Lightroom 5

  Adobe Community Help

  Products affected

  • 5 Lightroom

  Contact technical support

  Give feedback

  What is covered

  • Important information for all platforms
  • Locations of files on Mac OS X
  • Locations of files in Windows 7 and 8

  Upward

  Important information for all platforms

  • The files and the locations of files given here are default values. Some of these places can be customized in the Lightroom \Preferences or the catalog settings dialog boxes.
  • While troubleshooting, where possible, rename the files instead of remove them.
  • If possible, back up catalogs on another hard drive or a volume of the disk where your catalog is located. For more information about the backup in Lightroom, read back up a catalog with Lightroom and look at the backup catalog on Adobe TV. (The video has been produced for Lightroom 4 but still applies to Lightroom 5.)

  Upward

  Locations of files on Mac OS X

  Note:

  The user library file is hidden by default on Mac OS X 10.7 and later versions. For temporary access to the file library user, press Option and select go > library in the Finder.

  The Lightroom application file

  / Applications/Adobe Photoshop Lightroom 5. app

  Preferences

  /Users/[user name]/Library/Preferences/com.adobe.Lightroom5.plist

  Catalog

  /Users/[username]pictures/Lightroom/Lightroom Catalog.lrcat 5

  The preview cache

  /Users/[username]pictures/Lightroom/Lightroom Previews.lrdata 5 catalog

  Smart Preview cache

  /Users/[username]pictures/Lightroom/Lightroom 5 catalog Previews.lrdata Smart

  Locking of catalog file

  /Users/[username]pictures/Lightroom/Lightroom 5 Catalog.lrcat.lock

  Note: The locking file prevents the catalogue to be crushed when using.

  Log file catalog

  /Users/[user name]5 pictures/Lightroom/Lightroom Catalog .lrcat - journal

  Note: Open catalogs use the log file to check the incomplete database records. Do not delete the log file unless you delete its associated catalog, as well.

  The Catalog backup

  /Users/[user name]/[date and time of backup]Lightroom Catalog.lrcat 5

  Models and pre-defined parameters

  /Users/[user name]/ Library/Application Support/Adobe/Lightroom /[folder preset or model]/[preset or template filename.lrtemplate]

  Serial number

  /Users/[user name]/ Library/Application Support/Adobe/Lightroom/Lightroom 5.0 registration

  Odd. Try this:

  Make sure the Finder window is active.

  Without press the Option key, click and hold the tab top Go to the screen, you see the drop-down list.

  Without releasing the mouse, press the Option key.

  See you on the drop-down list changes?

• First breaks down after clicking the imported video file

  After clicking on one just imported the video file (in this case. MOV to a Nikon 7100) application hangs and displays "Adobe Premiere Pro CC 20141 has stopped working" and the problem, the details are below. I tried to reset preferences but do not know what else to try. First starts up fine and I can import pictures very well but any video file (I tried. MOV. MP4. AVI. WMV) that gets imported hangs the software as soon as I try to do something with it.

  Any help would be greatly appreciated!

  -Aisha

  System details:

  Windows 7 Professional, Service Pack 1

  Processor: Intel Core i5 - 4570 T CPU @ 2.90 GHz

  RAM: 12 GB

  Details of the problem:

  Signature of the problem:

  Problem event name: APPCRASH

  Name of the application: Adobe first Pro.exe

  Application version: 8.1.0.81

  Application timestamp: 5426694c

  Fault Module name: devenum.dll

  Fault Module Version: 6.6.7600.16385

  Timestamp of Module error: 4a5bded7

  Exception code: c0000005

  Exception offset: 00000000000016a 0

  OS version: 6.1.7601.2.1.0.256.48

  Locale ID: 1033

  Additional information 1: ec5a

  More information 2: ec5adb2545b190cc19da7bdfa78d5bf1

  3 more information: 52eb

  Additional information 4: 52eb6b5eb5247c23714f771b797ebaa7

  Read our privacy statement online:

  http://go.microsoft.com/fwlink/?linkid=104288 & clcid = 0 x 0409

  If the online privacy statement is not available, please read our offline privacy statement:

  C:\Windows\system32\en-US\erofflps.txt

  Hello

  Create a new project and without importing anything, go to file > project settings > General and change the playback engine Mercury to the GPU acceleration only software and click on remove previews after clicking OK. Then import the media.

  Hope this helps,

  Regalo

• I want to see the VM configuration files

  Hello

  I want to see the VM configuration files. Can you explain it please with screenshots.

  Kind regards

  DJ

  Hello

  The links provided of Andrew are good and explains a lot of things and hope that the below a will also help more...

  If you want to display your virtual machine using GUI Configuration files, and then follow the steps below

  1. connect to your customer VI or Vcenter and identify the virtual machine that you want to display the Configuration of the 'Search' tab in the right-hand

  2. When you have found the right VM, go to the settings and find on what data store, it is present and go to these data, store and right click on that and select Browse the data store

  3. Select the folder with the name corresponding to your virtual machine name, and you will be able to find all the files that you see in the attached picture.

  If you want to display your virtual machine by using the CLI Configuration files, and then follow the steps below

  1. connect to ESX using the Console used in your environment (for example: Putty) with your root and PW id (or your existing access)

  2. Once you log in, go to "cd/vmfs/volumes" (commonly used way... can also vary)

  3. as you know from the data store, type 'cd datastorename' and you have the list of virtual machines that you had in the GUI, and then select the virtual machine using the same "vmname cd.

  4. Once you're in the virtual machine, use the ls command and you can view all the files in it

  5. If you need more information on ls you can use the link below

  http://www.computerhope.com/UNIX/ULS.htm

  Hope 2 modes above helps you to better...

  Chavigny$ $$

  "Life is boring without challenges & risks taken in daily life.

• Different sound level on the exported audio files?

  Today, I opened Audition, created a session multitrack with sampling frequency 44100KHz, 2 channels (stereo) and 32-bit depth.

  I tried to merge a part of a song with the rest of another song, but I realized that the hearing has a low sound level as Windows Media Player or any other media player.

  I looked for any configuration that could make WMP change the original sound, but he did play the song with the original sound level

  If I have the low sound of hearing was something that wouldn't stay in the exported file.

  But he did! And it was always like that, not just today.

  What should I do?

  It is not entirely clear as to where is your lower level, but if you're talking about level hearing on the mixing being 3dB lower than what happens when you play multitrack, then the answer is simple - you need to reset the pan law-3dB center left/right cut (logarithmic) - this option is in the preferences > multitrack at the top of the pane. This will give you the same level on a file drop-down mixed or exported as you see on the screen.

  But if you talk of levels of listening about, then it is very difficult to make useful comparisons to all levels of output. WMP and hearing use drivers and completely different engines, to the sounds of Windows via the Windows mixer - which changes even when reading levels. Hearing, if it goes directly to an audio device via an ASIO driver, don't get disturbed by the operating system in the slightest (that is the idea...), but if she gets plugged into the operating system for the output, then once more, the level can be changed through the Windows mixer.

  But in the final analysis, it's not really important. Hearing files can be standardized so that the peaks are just below 0 dBFS, and if you do that, they will play correctly on any other player. If they seem to be more silent, it will be because of the overall volume of the file, and it is a decision of mix - nothing to do with the format of file at all. And this is often a problem with the mixture of two songs from different sources together - if it is been compressed a lot to make it sound louder and the other does not, while the levels will never match perfectly to the join, whatever you do. Your only recourse here would be to compress the most calm one more to match the first - but that 's going to change the sound, probably in ways you might not like.

  So, quite a lot of options, really.

• CA edition do not read the scenario definition files

  Hello
  It is a migration from 2007.3-10 project. Configuration of a deployment of CA & fall on issues as long as it is impossible to read the SDL. Here is the error. This is the first deployment FULL time CA to commerce server.
  As a work around, I copied the folders published & SCENE files (running on ATG 2007.3) and stuck in my DEV(C:\ATG\ATG10.0.3\home\Publishing\versionFileStore\PublishingFiles). The deployment completed successfully. This clearly indicates that the problem is with the edition. Any guess?
  
  
  + 13:12:08, ERROR 306 [DeploymentManager] +.
  CAUGHT AT:
  Container: ATG. Deployment.file.DeploymentSourceException: IOException when playback of the file /atg/registry/data/scenarios/recorders/das.sdl; SOURCE: deploymentFileCommandIOExcReadF
  Island: level 4: IOException while reading the /atg/registry/data/scenarios/recorders/das.sdl file
  atg.deployment.file.DeploymentSourceException: IOException while reading the /atg/registry/data/scenarios/recorders/das.sdl file
  at atg.deployment.file.FileWorkerThread.handleErrorLogging(FileWorkerThread.java:1239)
  at atg.deployment.file.FileWorkerThread.handleError(FileWorkerThread.java:1254)
  at atg.deployment.file.FileWorkerThread.runCommand(FileWorkerThread.java:740)
  at atg.deployment.file.FileWorkerThread.processMarkerForAddUpdatePhase(FileWorkerThread.java:420)
  at atg.deployment.DeploymentWorkerThread.processMarkerPhase(DeploymentWorkerThread.java:534)
  at atg.deployment.DeploymentWorkerThread.run(DeploymentWorkerThread.java:307)
  Caused by: deploymentFileCommandIOExcReadFile: level 4: IOException while reading the /atg/registry/data/scenarios/recorders/das.sdl file
  atg.deployment.file.DeploymentSourceException: IOException while reading the /atg/registry/data/scenarios/recorders/das.sdl file
  to atg.deployment.file.DeploymentSourceException. < init > (DeploymentSourceException.java:52)
  +... 6 plus +.
  EXCEPTION SOURCE:
  
  Thank you!
  Mani

  I think 'das.sdl' is the scenario OOTB file that would be loaded with the initial data. But if you choose to configure ATG 10.3 with no initial data will not present in PublishingFiles the AC. Copy the existing PublishingFiles of ATG environment may be the only solution.

  ~ Srinivas