Unable to get copy of targeting DAQmx.dll 4.5 / / the type 'NationalInstruments.ISynchronizeCallbacks' is defined in an assembly that is not referenced.

Similar Questions

• HP C7240 message "Unable to scan, copy or fax" appears when I lift the cover on dish

  This happened for some time. Whenever I raise the lid, this message appears: "unable to scan, copy or send a fax. If I type "OK" everything returns to normal. I am able to fax and scanning from the doc feeder, but some things are just too thick to put thru. I tried to put my paper under the lid while the appliance has been turned off, so I was not raised the lid, perhaps thinking he might still scan from the dumpster, but no. I get the same message as soon as I turn on the printer. Running Windows 7.

  In addition, there is a line on my paper when I scan through the doc feeder. No idea how to get clean or repair everything that makes the line?

  Thank you!

  Yes, life has a way of doing that sometimes.  I'm you a link to a document of troubleshooting for lines in copies of the automatic feeder (ADF) documents.  Click here  A thorough cleaning of the ADF will probably solve this problem.

  The error message "Unable to copy, scan or fax" may be more difficult to overcome.  On the only step left that could be considered would be a semi full reset.  This reset the default printer and clear the memory.  If the printer was on a wireless network, it should be removed and would need to be reconnected.  If you want to try this, I can send you the steps in a private message.  I need you agree to not post the stages.  Let me know what you decide.

• Why should I copy of a CVI DLL compiled in the System32 folder?

  Hello

  I've been letting the compiler CVI copy of a DLL (project) in the windows\System32 folder.

  It was mainly to leave more than 1 other executables CVI, installed in different folders under \Program Files\

  Discover and share this code of the DLL.

  In addition, when you build the kit distribution for the DLL, I directed the DLL must be installed in the System32 folder.

  When you introduce this concept in a review to an other software engineers, a mechanic found that the System32 folder should be reserved for windows, hardware drivers, etc.. My CVI DLL needs to reside in the working folder of the executable main partner, or any other location. His concerns were uninstalling and updating process, and if the DLL were at a location specified by the installer, it would be easier to follow, etc..

  I'm assuming that NEITHER recommended CVI to "COPY IN the \Windows\System32 folder. Why?

  Should my fellow engineer some friendly advice?

  [BTW, he used NEITHER CVI occasionally, especially with other languages]

  Thank you ALL

  Scott Youngren with CVI 8.1.x

  Hi Scott,.

  Even if we are aware of them or not, most programs use System32 as their destination of DLL.

  I myself wouldn't mind too much about.

  Have you seen this document?

  You can install to a different location and use the PATH environment variable where you can not convince that system32 is ok.

• OIM 11 g R2: target setting dependend attribute on the type of process (create, update, disable)

  Hello

  I try to set an attribute ('Action') of users on a target system (Lotus Notes) dependend on the type of process which was conducted:

  When the user is created in Lotus Notes by the IOM, 'Action' should be on the value 'create '.

  When the user is updated in Lotus Notes by the IOM, 'Action' should be on the value "update".

  When the user is disabled in Lotus Notes by the IOM, 'Action' should be on the value "disable."

  What would be the best way to achieve this? And exactly how I should implement that? (I tried to read the documentation on the tasks of the adapter, however I could not get that to work...).

  Thank you!

  M

  Hello

  Its easy to accomplish by using adapter process task.

  (1) create a field on your form of process as 'Action '.

  (2) create a new process task in Lotus Notes process definition for "Action Updated" (you can use OOTB adapter for mapping purposes)

  (3) create a new task adapter process that fills that takes input like input1 and back to the entrance.

  (4) create the 3 tasks in process in Lotus Notes process definition. One for each action. For example: Update Action such as activate, Action such as disable update, update Action as Create. In the tasks of each process, pass the entrance as enable, disable and create respectively.

  (5) to map each tasks created in step 4 success of Create User, user, user disable respectively.

  ~ J

• DAQmx property to identify the type of device

  Hello is there is another property of DAQmx device which would amount to what is the main measure type for some devices?
  This means for example:
  9201 would return analog
  9203 = current
  9211 thermocouple =
  Thank you!

  Hey Ceties,

  What you can do is to use the node DAQmx Device, property with the property 'Type of product. This will give you the type string, as NI 9211. With this info, you must create a clean table with values of matched string (such as "Thermocouple") and has chosen the right of the table. Unfortunately it is that no property tha will directly give you this information.

  Please let me know if you need anything else!

  Best regards

  David Varga

  Technical sales engineer

  NIH

• How to get information about the types within a user defined package

  Hi all
  Have a package with some types (user-defined) defined in the package specification. How to get information about the types and
  information about the columns of this type.
  
  for example:
  Create package mp is
  
  type t is record (no number is varchar2 (30));
  
  procedure a (m t out...
  
  Thanks in advance.
  
  userg

  G_user wrote:
  the req's, want to build a script dynamically using data dictionary
  so if possible, I take the name of the type within the package specification.

  Let me rephrase - is there a data dictionary to get information on the type defined by the user within a package specification

  Best approach will be to have a standard in the definition of data types.

  Have a process to follow the object definitions in the package if it is mandatory.

• Unable to get to my files 'images' or 'documents' in the start menu.

  I can't have my 'images' or 'documents folders in the start menu. I can't select a photo from my photo folder in the start menu. And finally, empty document files appear on my desk at random. I am running Vista Home premium.

  Hi Paul,.

  1. don't you make changes to the computer before the show?
  2. what happens when you try to access 'photos', or ' documents folders in the start menu?
  3. what happens when you select a picture in my photo folder in the start menu?
  4. do you get the error message?

  Method 1
  Step 1: I suggest to start the computer in safe mode and check if the problem persists.

  Startup options (including safe mode)
  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Step 2: If the problem is solved in safe mode, then I suggest you perform the clean boot and remove the program that is causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: Follow step 7 clean boot KB929135 article to reset the computer in normal mode.

  Method 2
  I suggest you run virus scan online by using the Microsoft safety scanner.

  Microsoft safety scanner
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: when you do an antivirus online, you will lose data that are affected by the virus. Microsoft is not responsible for the loss of this data.

• How can I copy my old hard hard 'C' to the new reader, "C" drive reports an error and I can not clone!

  My 'C' drive is reported to be in danger of not, so I bought a new 500 GB drive which is currently housed in an external enclosure, my problem is I want to clone my old drive to my new but when I try an error is reported and the process stops.  I installed Win7 as an upgrade of Vista, so I can't mount the new drive as master, and then install Win7 because it will search the former Vista program before it will run. Is there a way I can install Win7 on my new record, at present in the external box connected via USB, and then exchange the reader to the PC to become my new 'C' drive and then individually copying my programs over the old 'C '?   I hope this makes sense, any help would be apprecisted.

  Thank you, Peter pond in the United Kingdom.

  If you have another hard drive, you can put in the case of external use Windows 7 builtin imaging app (Control Panel, Backup & Restore) to take a picture of the old hard disk Save external hard disk. You will also need to make the system repair disc to boot from to restore the image to new hard drive.

   

  Once you're all set, install the new hard drive, boot from cd/dvd repair.

   

  http://www.howtogeek.com/HOWTO/4241/how-to-create-a-system-image-in-Windows-7/

• help when I try to upgrade this is what I get - the key entered is for an edition of windows that does not work with windows anytime upgrade. Enter a different key upgrade

  the key is a W7 starter upgrade to W7 Home premium. bought the Comet, unfortunately.

  The first thing you need to do is to get your key to Windows 7 Professional upgrade Express:
   
  An e-mail containing your product key will be sent to the e-mail address associated with your Windows Live ID account or e-mail address you provided if you ignored the account configuration. Note: If you use an email tool or spam blocker spam filter, be sure that you can receive e-mail messages from microsoft.com.
   
  What happens if I lose my product key?
   
  If you lose your product key, you can return to

  www.Windows7.com/GetKey and sign in using the "Sign In" link in the upper right of the page. This will allow to recover your product key if you have established your account with your Windows Live ID. If you do not configure a Windows Live ID account initially there is no record of your online product key. Check your e-mail since it is the only trace of your product key.
   
   
   
  or

  Here are four utilities, which can display your product keys if they are still there:
  Belarc Advisor: http://www.belarc.com/free_download.html
  (He did a good job of providing a wealth of information.)
   
  Also: http://www.magicaljellybean.com/keyfinder.shtml
  and: http://www.nirsoft.net/utils/product_cd_key_viewer.html
  and RockXP: http://www.majorgeeks.com/download4138.html which has additional features.
   
  --------------------
   
  The next thing you need to do is to ensure that your data is backed up:
   
  http://notebooks.com/2010/12/27/how-to-backup-to-an-external-hard-drive/
   http://notebooks.com/2011/02/25/how-to-restore-a-backup-from-an-external-hard-drive-in-Windows-7/
   
  -------------------
   
  The next thing you need to do is to reinstall the base license that you upgraded, Windows 7 Starter Edition or Home Premium.
   
  If your computer is pre-installed with Windows 7:
   
  New computers coming often pre-installed with Windows 7 have what is called a recovery partition. This is used to reinstall an operating system in the case of a system failure. To access it, you need to start when you start your computer by pressing a function key. This can be either F1, F2, F9, F10, F11, F12 key DEL or tab. See the manual that came with your PC for instructions on how to reinstall Windows.
   
   
   
  -Samsung uses ESC on most of its systems
   
  -HP use F9 on most of its systems
   
  -Fujitsu uses F12 on most of its systems
   
  -Acer use F12 on most of its systems, but often you need to go into BIOS to allow

  -Dell uses F12
   
   
   
  In general, look at the screen during the POST for a tip for what is possible.
   
   
   
  If your recovery partition is not available or damaged, you must contact the manufacturer of your computer, and request that a defined recovery disk you can use to reinstall Windows 7. They could practice a small shipping and handling.
   
   
   
  ------------------------
   
  If it was a store bought retail license:
   
  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7
   
   
   
  --------------------
   
  After you have reinstalled your original license, make sure that it is enabled before doing the upgrade to Windows 7 Professional:
   
  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
   http://support.Microsoft.com/kb/950929/en-us

  ----------------------
   
  Redo the Express Upgrade:
   
  Click Start, type Anytime Upgrade, click on the option enter a key, enter the key of Windows 7 Professional on demand, click Next, wait while checking the key, accept the license agreement, click on upgrade, wait while the software upgrades, (it may take 10 minutes or more depending on the if updates are required) your computer restarts automatically, after the reboot, Windows 7 will notify you updating the computer, the computer will restart once more automatically and will be completed the upgrade, a window will appear notifying the upgrade was successful and your computer is ready to use, click Close, you should be upgraded to Windows 7 Professional your files, programs and settings retained.
   
   
   
  ---------------
   
  Go to reactivate the license again.

• Hi, I have a d630 Latitiude. I recently bought this and have loaded XP pro. I am unable to get my wireless

  My service tag is (6W9FR1S). I am unable to get my wireless to work (although bluetooth works) the wireless light on the lower right part of the screen don't light up either.

  I downloaded all the drivers of your download page. Cable connection is working, but I can't get the machine to see the wireless card

  In my device manager, everything seems to be ok except: -.
  I have a yellow icon (?) with a "!" to the following: -.

  Biometric co-processor
  Network controller
  Video controller
  Video controller (VGA Compatible)

  The Dell quick set does not give me the opportunity to set up a wireless network

  Help!

  You must install capabilities of wireless network from a windows xp installation cdrom

• Unable to get Web 5.5 console vcloud Director?

  Hi all

  I am unable to get vcloud Director console, I configured successfully and the ping command console and http proxy ip addresses. Manager VSheild successfully configured. The certificates are generated. Please let us know what is the problem and what is the solution for this?

  I managed to break, I just had to stop the firewall services, I just run the command service iptables stop, everything was fine, I got the console.

• Your computer is unable to get out of hibernation 0xc000007b

  On my windows 7 Professional, 64-bit when I wake up my laptop I have this message: your computer can't get out of hibernation. Status: 0xc000007b Info: a fatal error has occurred processing the restore data. File: \hiberfil.sys any information that was not justified until the computer entered hibernation will be lost.             Does anyone have a solution for this error? Thanks in advance!

  0xc000007b error code appears whenever an application or service could not start. In this case, the problem is with the hibernation.

  Therefore, as a first step, please answer the questions:

  1. don't you turn off the power/remove battery voltage while hibernation (hibernation shows no sign of progress, so those used to pull off the camera, since it is associated with power, defective battery also causes this problem)?

  2 - is happens the issue even at the resumption of his sleep?

  Case 1:

  If the answer is Yes to question 1, kindly make sure enough current is present until the computer is shut down completely. If there is no indicator LED/all other present, please wait for 3 to 5 minutes before turning off the power.

  Case 2:

  If the answer to question 2 is Yes, you can try to upgrade display drivers (graphics card drivers). If the upgrade fails to resolve the problem, reinstall the drivers: uninstall the drivers, reboot the PC, install the drivers, reboot the PC and then check.

  Case 3:

  If the answer to the two questions above is no, please follow the steps:

  Go to start-> type cmd-> right-click on->, click Run as administrator. If guests UAC, click Yes. Then, at the command prompt, type the following line and press enter (disabling hibernation):

  powercfg-h off

  Then, restart the PC a couple of times. Then, the same way open the command prompt, type the following command and press enter (enabling hibernation):

  powercfg-h on

  Then try to hibernation.

  If the problem persists, once again, disable hibernation, perform a disk defrag, restart the computer and hibernation to activate it. Follow the link for more information about disk defragmentation:

  http://Windows.Microsoft.com/en-us/Windows/improve-performance-defragmenting-hard-disk#1TC=Windows-7

• Unable to get the total number of records processed by the processor of trade rules

  Details of the environment

  ======================

  Disqualification Version: 12.1.3.0.0

  
  

  I use a business rules processor to implement multiple business rules on one record and I am looking for a summary of the number of records increased and does not have a specific rule.

  
  To illustrate:
  Suppose there are 2 rules, invalid number in Column1 and valid number on Column2.
  10 records to process and 3 folders don't rule 1 (valid on column1) and 9 entered failure of rule 2 (valid number on Column2).

  In the browser of result of the processor Business, the number of past records and failed is displayed but is not part of the output of the processor itself. In the example above, there will be 1 pass and 9 fail records and given the values of said the total number of records can be derived which is 10.

  This is why the expected output will be:
  Success of failure
  Rule 1:7 (10-3) 3
  Rule 2: 1 (10-1) 9
  Note: The number of records that failed can be derived from the table of the rule ID but I don't know how to get the total number of records in order to calculate the number of records that a given rule.

  I tried to publish the County of acceptance and rejection in the browser of result of the processor Business in an intermediate table and ask the same intermediate table to get the pass and fail values but Disqualification does not allow to write and read the same intermediary object in a single process. What is the best way to get the number of records total handled by the processor business rules? This kind of attributes (that do not exist only in the browser of result) can be included in the output of the processor in the next version of the Disqualification?

  In addition, the intermediate table contains only 1 sheet with pass and failure values while the exceptions which have individual failure on each rule contains 12 Archives. What would be the best approach to merge a single record into multiple records according to the example below?

  Staging table
  Success of failure
  1 9

  Exception table
  Single ID ID rule
  Rule 1 Record1
  Rule 1 Record2
  Rule 1 record Record3
  Rule 2 Record1

  Exception table with: staging Table data merge
  Rule ID ID Unique Pass Fail Total
  Rule 1 1 9 10 Record1
  Rule 1 1 9 10 Record2
  Recording rule 1 Record3 1 9 10
  Record1 rule 2 1 9 10
  
  Please notify.

  Hi Jason,

  The best way to explain how to do this is with an example project (DXI). I'll send you one in offline mode.

  -Mike

• How can I get a player opens in view "content of the list.

  How can I get a player opens in mode "List content" instead of "search"?  When I double-click on a player, the window opens a search box instead of list files that are there.

  I can get around through the back door (My Documents), or by practice:

  1. start > 2. Click on the drive (C :) > 3) File > 4. Open

  But I'd rather just double click on the c drive icon and get a list of content, not a search box.

  How can I get a player opens in mode "List content" instead of "search"?  When I double-click on a player, the window opens a search box instead of list files that are there.

  I can get around through the back door (My Documents), or by practice:

  1. start > 2. Click on the drive (C :) > 3) File > 4. Open

  But I'd rather just double click on the c drive icon and get a list of content, not a search box.

  Right-click on the drive icon.  One of the items in the context menu that opens will be in bold.  I guess that for you, the part in bold is to 'Search' and not 'open '.

  Go to start/run and type: regsvr32 /i shell32 [click OK]

  If that is not correct the problem, then:

  Image search opens by Double clicking on a folder or drive (line 18)
  http://www.kellys-Korner-XP.com/xp_tweaks.htm

  To use the VBS file: download .vbs file and save it to your hard drive
  (you can right-click and save target as). Double-click on the
  vbs file. You will be asked when the script is done.

• I can't open the RAW files from my Nikon D800 (i.e. NEF files).  I use a Mac with Photoshop CS5 and El Capitan 10.11.2 version running.  I get a message "could not complete your request because the file appears to be a model of camera that is n

  I can't open the RAW files from my Nikon D800 (i.e. NEF files).  I use a Mac with Photoshop CS5 and El Capitan 10.11.2 version running.  I get a message that "could not complete your request because the file appears to be a model of camera that is not supported by the installed version of Camera Raw. Please visit the Camera Raw help documentation for more information. "Yet the Nikon D800 is on the list of supported devices.  Can anyone help?

  And temporarily disable the Gatekeeper by allowing downloads from anywhere, or your installer will be marked as 'damaged' because that CS5 is out before Gatekeeper and is not "signed" that is not approved.