VPN site to site UP, but no traffic
Dear friends,
I did a VPN site to site using ASA 5555 02 in each site running the Version of the software 9.2 (4).
The VPN is UP, as shown below:
ASA-SSP-Pri (config) # sh isak his
There are no SAs IKEv1
IKEv2 SAs:
Session-id: 1, State: UP-ACTIVE, IKE County: 1, number of CHILDREN: 1
Tunnel-id Local remote status role
201.23.100.130/500 268373031 200.174.36.19/500 LOAN MACHINE
BA: AES - CBC, keysize: 256, Hash: SHA96, Grp:5 DH, Auth sign: PSK, Auth check: PSK
Duration of life/active: 86400/272 sec
His child: selector local 10.69.0.0/0 - 10.69.0.255/65535
selector of distance 10.12.20.0/0 - 10.12.20.255/65535
SPI ESP/output: 0xf89430e6/0x86a5cd8f
But when I try to ping from one site to another, is not possible, the result of the ping command is '?
I did some research on this problem and a lot of people say that Miss crypto isakmp nat-traversal 20 command, but this command is already enabled.
Exempt from NAT is enabled and I did tests of deactivation as well.
Hello
The last thing I think is that there is a SPINNAKER twice on the table of the asp and that is why the traffic is not encrypted everything seems correct, run the following command on the ASA:
clear crypto ipsec its inactive
test again
Tags: Cisco Security
Similar Questions
-
VPN - VPN easy hardware Client connects, but no traffic
Hello
I have a PIX 515E and 501 acting as a customer of material. Several remote location are connected as a easy VPN clients, a place to connect, but no traffic flows. I went from mode-extension-network client mode and I can connect through other network hosts.
I don't know why this 501 PIX we're different. There is no ACLs except which is extracted from the station.
Any ideas where I should look?
Thank you
Vince
A few quick comments:
1. I don't see 192.168.0.0 is part of this ACL inside_outbound_nat0_acl.
2. I see an instance of card crypto 40 with "incomplete" crypto card, which is actually not a correspondence address.
outside_map 40 ipsec-isakmp crypto map
peer set card crypto outside_map 40 216.27.161.109
outside_map card crypto 40 the transform-set ESP-DES-MD5 value
! Incomplete
Not sure if it's the current configuration of the pix. If there is an instance of card crypto with an incomplete correspondence address, all traffic will be encrypted.
Kind regards
Arul
-
VPN Tunnel to the TOP but no traffic passing (PIX515)
I'll put up a remote engineers access to off-site to access my network (using the cisco vpn client). I use PIX 515E software version 7.0 (3) 20 as a vpn server. I can establish a tunnel, but I can't access network resources. I can ping the external interface of the PIX. This is my setup: internet-router-pix-dmz(server farm). Please find attached my setup. Thanks in advance.
After a glance at your policy, it seems that the Pool of IP, that is assigned to the clients behind the outside interface, runs behind the DMZ. I don't think it will work.
In addition, defined distribution policy seems to be backward. Im sure that you intend to send traffic FROM the IP pool to 196.26.12.64/26. Your acl split is the opposite.
In addition, your routing table does not contain a route for the 196 network, so the firewall will use the default route to the outside. If this is intentional, the clients and dst are on the outside, which is considered to be crossed. This is allowed on the SAA only with the same security setting configured.
-
VPN site to Site one-way traffic
Hi all
I set up a Vpn site-to site and everything works well in the remote site to the corporate site, but since the site of the company asa 5510, I can't access to the remote site asa 5505. I checked the logging on the SAA and I can see the packets being fallen but I can't find what I need to do to allow this traffic through. Here are most of my 5510 config, I'm sure it's something simple I'm missing, but I can't run it please help.
REMOTE network is 192.168.72.0
: Saved
: Written by enable_15 at 10:29:17.163 GMT/BDT Thu Jun 10 2010
!
ASA Version 8.0 (5)
!
host name Casa
uk domain name
activate the encrypted password of VgZT0UwPdkSV9l7N
zlo5ImUVRkHl4lcl encrypted passwd
names of
name 192.168.103.14 description of Appliance CITRIX CITRIX Appliance
name 192.168.3.12 description villages villages
DNS-guard
!
interface Ethernet0/0
nameif outside
security-level 0
IP address x.x.x.123 255.255.255.224
!
interface Ethernet0/1
nameif inside
security-level 100
192.168.3.254 IP address 255.255.255.0
!
interface Ethernet0/2
nameif dmz
security-level 50
IP 192.168.103.254 255.255.255.0
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
management only
!
boot system Disk0: / asa805 - k8.bin
boot system Disk0: / asa707 - k8.bin
passive FTP mode
clock timezone GMT/UTC 0
summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS server-group DefaultDNS
uk domain name
object-group network ExternalAccess
Description hosts allowed direct web access
network object-SVR-01 255.255.255.255
SVR GIS 255.255.255.255 network-object
host of network-object cient
host villages network-object
the ExternalAccessFromDMZ object-group network
Description hosts allowed direct web access to DMZ
CITRIX-device 255.255.255.255 network-object
network-object IRONPORT1 255.255.255.255
worker of the object-network 255.255.255.255
MitelUDPinternet udp service object-group
Description Mitel UDP services on the internet
20000-27000 object-port Beach
port-object eq sip
port-object eq 5064
MitelTCPinternet tcp service object-group
Description Mitel TCP services on the internet
port-object eq 2114
port-object eq 2116
port-object eq 35000
port-object eq 37000
port-object eq 3998
6801-6802 object-port Beach
port-object eq 6880
port-object eq www
EQ object of the https port
port-object eq 6800
EQ object Port 3478
port-object eq sip
EQ port ssh object
MitelTCPinternetOpt tcp service object-group
Description Mitel TCP optional services on the internet
port-object eq 3300
6806-6807 object-port Beach
36005 36005 object-port Beach
36005 36006 object-port Beach
EQ object Port 3478
port-object eq sip
MitelUDP2LAN udp service object-group
Description Mitel UDP for the local network of services
object-port range 1024-65535
port-object eq sip
MitelTCP2LAN tcp service object-group
Description Mitel TCP for the local network of services
port-object eq 2114
port-object eq 2116
port-object eq 35000
port-object eq 37000
port-object eq 1606
object-port 4443 eq
port-object eq 3998
port-object eq 3999
6801-6802 object-port Beach
port-object eq 6880
port-object eq www
EQ object of the https port
EQ object Port 3478
port-object eq sip
acl_outside list extended access permit icmp any any echo response
acl_outside list extended access allow all unreachable icmp
acl_outside list extended access permit icmp any any source-quench
acl_outside list extended access permit tcp any host Mail_Outside_AGH eq smtp
acl_outside list extended access permit tcp any host Mail_Outside_AGH eq https
acl_outside list extended access permit tcp any host x.x.x.123 eq ssh
acl_outside list extended access permit tcp host x.x.x.x host Icritical_Outside eq ssh
acl_outside list extended access permit tcp any host Citrix_Portal_outside eq 8088
acl_outside list extended access permit tcp any host Citrix_Portal_outside eq https
acl_outside list extended access permit tcp any host Citrix_Portal_outside eq 8081
acl_outside list extended access permit tcp any host Mail_Outside_AVON eq smtp
acl_outside list extended access permit tcp any host Mail_Outside_AVON eq https
acl_outside list extended access permit udp host x.x.x.x host Icritical_Outside eq snmp
acl_outside list extended access permit udp host x.x.x.x host Icritical_Outside eq snmp
acl_outside list extended access permit tcp any host teleworker_outside MitelTCPinternet object-group
acl_outside list extended access permit udp any host teleworker_outside MitelUDPinternet object-group
acl_outside list extended access permit tcp any host teleworker_outside MitelTCPinternetOpt object-group
acl_outside list extended access permit tcp host x.x.x.x host Icritical_Outside eq ssh
acl_outside list extended access permit udp any host ESX-PAL-01 eq ntp
acl_outside list extended access permit udp any host ESX-PAL-02 eq ntp
acl_outside list extended access permit udp any host ESX-PAL-03 eq ntp
inside_outbound_nat0_acl to access ip 192.168.1.0 scope list allow 255.255.255.0 172.30.100.0 inactive 255.255.255.224
inside_outbound_nat0_acl list of allowed ip extended access all 172.31.1.0 255.255.255.0
inside_outbound_nat0_acl to access extended list ip 192.168.3.0 allow 255.255.255.0 192.168.103.0 255.255.255.0
inside_outbound_nat0_acl to access extended list ip 192.168.3.0 allow 255.255.255.0 192.168.72.0 255.255.255.0
inside_pnat_outbound list extended access allowed object-group ip ExternalAccess everything
acl_dmz list extended access permit ip host host IRONPORT1 Mail_Inside_AGH
acl_dmz list extended access permit udp host field of pal-svr-22 eq IRONPORT1 host
acl_dmz list extended access permit tcp host IRONPORT1 host pal-svr-22 eq 3268
acl_dmz list extended access permit udp host host IRONPORT1 ARM-SVR-01 eq field
acl_dmz list extended access permit tcp host IRONPORT1 host ARM-SVR-01 eq 3268
acl_dmz list extended access permit udp host host IRONPORT1 Pal-Svr-17 eq field
acl_dmz list extended access allowed icmp host host IRONPORT1 Mail_Inside_AGH
access extensive list ip 192.168.103.0 acl_dmz allow 255.255.255.0 any
acl_dmz list extended access permit tcp host host CITRIX-device-CITRIXCSG-lan eq https inactive
acl_dmz list extended access permit ip any host CITRIXCSG-lan idle
acl_dmz list extended access permit tcp host IRONPORT1 eq Mail_Outside_AGH smtp
acl_dmz list extended access permit tcp host teleworker host 192.168.20.1 object-group MitelTCP2LAN
acl_dmz list extended access permit udp host teleworker host 192.168.20.1 object-group MitelUDP2LAN
dmz_pnat_outbound list extended access allowed object-group ip ExternalAccessFromDMZ all
access extensive list ip 192.168.103.0 dmz_nat0_inbound allow 255.255.255.0 192.168.3.0 255.255.255.0
dmz_nat0_inbound list of ip host 192.168.20.1 telecommuter host allowed extended access
access extensive list ip 192.168.21.0 inside_pnat_outbound_AVON allow 255.255.255.0 any
access extensive list ip 192.168.22.0 inside_pnat_outbound_AVON allow 255.255.255.0 any
access extensive list ip 192.168.23.0 inside_pnat_outbound_AVON allow 255.255.255.0 any
access extensive list ip 192.168.24.0 inside_pnat_outbound_AVON allow 255.255.248.0 all
inside_pnat_outbound_AVON to access extended list ip 192.168.32.0 allow 255.255.240.0 everything
access extensive list ip 192.168.48.0 inside_pnat_outbound_AVON allow 255.255.248.0 all
access extensive list ip 192.168.56.0 inside_pnat_outbound_AVON allow 255.255.252.0 all
access extensive list ip 192.168.60.0 inside_pnat_outbound_AVON allow 255.255.255.0 any
allow any scope to an entire ip access list
inside_nat_AVON_Marshall list extended access permit ip host Mail_Inside_AVON all
dmz_pnat1_outbound list of ip telecommuter host allowed extended access any
outside_1_cryptomap to access extended list ip 192.168.3.0 allow 255.255.255.0 192.168.72.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
logging e-mail notifications
uk address record
exploitation forest-address recipient [email protected] / * / critical level
Outside 1500 MTU
Within 1500 MTU
MTU 1500 dmz
management of MTU 1500
IP local pool vpnpool 172.31.1.1 - 172.31.1.254 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow no dmz echo
ICMP allow all dmz
ASDM image disk0: / asdm-625 - 53.bin
ASDM location SVR-01 255.255.255.255 inside
ASDM location svr-02 255.255.255.255 inside
ASDM location IRONPORT1 255.255.255.255 dmz
ASDM location 194.81.55.226 255.255.255.255 dmz
ASDM 255.255.255.255 inside server location
ASDM location CITRIX-device 255.255.255.255 dmz
ASDM group ExternalAccess inside
ASDM group dmz ExternalAccessFromDMZ
don't allow no asdm history
ARP timeout 14400
Global x.x.x.121 2 (outdoor)
Global 1 x.x.x.125 (outside)
Global Mail_Outside_AVON 3 (outside)
Global Mail_Outside_AGH 4 (outside)
Global teleworker_outside 5 (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 2-list of access inside_pnat_outbound_AVON
NAT (inside) 3 access-list inside_nat_AVON_Marshall
NAT (inside) 1 access-list inside_pnat_outbound
NAT (dmz) 0-list of access dmz_nat0_inbound outside
NAT (dmz) 4 access-list dmz_pnat_outbound
NAT (dmz) 5 access-list dmz_pnat1_outbound
static (inside, outside) tcp ssh Icritical ssh netmask 255.255.255.255 Icritical_Outside
static (inside, outside) tcp https Mail_Outside_AGH Mail_Inside_AGH https netmask 255.255.255.255
static (dmz, outside) tcp smtp smtp IRONPORT1 netmask 255.255.255.255 Mail_Outside_AGH
static (inside, outside) tcp https Mail_Outside_AVON Exchange_Inside_AVON https netmask 255.255.255.255
static (inside, outside) tcp smtp smtp Mail_Inside_AVON netmask 255.255.255.255 Mail_Outside_AVON
static (inside, outside) udp snmp Icritical snmp netmask 255.255.255.255 Icritical_Outside
static (dmz, outside) device-CITRIX-Citrix_Portal_outside netmask 255.255.255.255
static (inside, outside) Mail_Outside_AVON Mail_Inside_AVON netmask 255.255.255.255
static (dmz, external) teleworker_outside netmask 255.255.255.255 teleworker
Access-group acl_outside in interface outside
Access-group acl_dmz in dmz interface
Route outside 0.0.0.0 0.0.0.0 X.X.X.254 1
Route inside 192.168.0.0 255.255.0.0 192.168.3.3 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
oner http 255.255.255.255 inside
http 192.168.1.0 255.255.255.0 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
card crypto outside_map 1 set r.r.r.244 counterpart
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
No encryption isakmp nat-traversal
Telnet timeout 5
SSH x.x.x.x 255.255.255.255 outside
SSH Mail_Inside_AGH 255.255.255.255 inside
SSH timeout 5
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
prefer NTP server SVR - DC1 source inside
internal VPN group policy
attributes of VPN group policy
value 192.168.x.x 192.168.x.x WINS server
Server DNS value 192.168.x.x 192.168.x.x
enable IPSec-udp
value by default domain-ACE
username, password pmmPwcDD/inpnNfB VPN encrypted privilege 0
attributes of VPN username
Strategy-Group-VPN VPN
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address vpnpool pool
Group Policy - by default-VPN
Group-tunnel VPN ipsec-attributes
pre-shared key *.
tunnel-group r.r.r.244 type ipsec-l2l
r.r.r.244 tunnel ipsec-attributes group
pre-shared key *.
by default-group r.r.r.244 tunnel-Group-map
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the netbios
inspect the tftp
inspect the sip
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:8360816431357f109b3c4b950d545c86
: end
This route is duplicated with the remote network
Route inside 192.168.0.0 255.255.0.0 192.168.3.3 1
I suggest to make this more specific subnet or add something like
Route outside 192.168.72.0 255.255.255.0 outside_default_gateway_ip
Internal, if above not in fact help, put a trace packet to simulate traffic even that fails on the 5510.
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/p.html#wp1878788
Kind regards
-
Routing of traffic between two VPN Site-to-Site Tunnels
Hi people,
I am trying to establish routing between two vpn Site-to-Site tunnels which are destined for the same outside the interface of my Cisco ASA.
Please find attached flowchart for the same thing. All used firewalls are Cisco ASA 5520.
Two VPN tunnels between Point A and Point B, Point B and Point C is too much upward. I activated same command to permit security level interface also intra.
How can I activate the LAN subnets traffic behind Point to join LAN subnets behind C Point without having to create a tunnel separated between Point A and Point C
Thank you very much.
Hello
Basically, you will need to NAT0 and VPN rules on each site to allow this traffic.
I think that the configurations should look something like below. Naturally you will already probably a NAT0 configuration and certainly the L2L VPN configuration
Site has
access-list NAT0 note NAT0 rule for SiteA SiteC traffic
access-list allowed NAT0 ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
NAT (inside) 0 access-list NAT0
Note L2L-VPN-CRYPTO-SITEB access-list interesting traffic for SiteA to SiteC
access-list L2L-VPN-CRYPTO-SITEB permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
Where
- NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteA SiteC NAT traffic
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEB = LCA in configurations VPN L2L that defines the SiteA LAN to LAN SiteC traffic must use the VPN L2L existing SiteB
Site B
access list OUTSIDE-NAT0 note NAT0 rule for SiteA SiteC traffic
OUTSIDE-NAT0 allowed 192.168.1.0 ip access list 255.255.255.0 192.168.3.0 255.255.255.0
NAT (outside) 0-list of access OUTSIDE-NAT0
Note L2L-VPN-CRYPTO-SITEA access-list traffic for SiteA to SiteC through a Tunnel between A - B
access-list L2L-VPN-CRYPTO-SITEA ip 192.168.3.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
Note L2L-VPN-CRYPTO-SITEC access-list traffic for SiteA to SiteC through a Tunnel between B - C
access-list L2L-VPN-CRYPTO-SITEC permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
Where
- OUTSIDE-NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteA SiteC NAT traffic. It is this time tied to the 'outer' interface, as traffic will be coming in and out through this interface to SiteB
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEA (and SITEC) = are the ACL in the configurations of VPN L2L that defines the SiteA LAN to LAN SiteC traffic should use existing VPN L2L connections.
Site C
access-list NAT0 note NAT0 rule for SiteC SiteA traffic
NAT0 192.168.3.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0
NAT (inside) 0 access-list NAT0
Note list-access-L2L-VPN-CRYPTO-SITEB SiteC to SiteA interesting traffic
L2L-VPN-CRYPTO-SITEB 192.168.3.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0
Where
- NAT0 = is the ACL to be used in the NAT0 rules that will exempt SiteC to SiteA NAT traffic
- NAT = is the line of configuration NAT0
- L2l-VPN-CRYPTO-SITEB = LCA in configurations VPN L2L that defines the SiteC LAN to LAN SiteA traffic must use the VPN L2L existing SiteB
To my knowledge, the foregoing must manage the selection NAT0 and traffic for VPN L2L connections. Naturally, the Interface/ACL names may be different depending on your current configuration.
Hope this helps
-Jouni
-
VPN Site to Site ASA (only happens with interesting traffic)
Is anyway to get an ASA to VPN site-to-site ASA addition interesting traffic? I need to keep this tunnel independently of traffic is anyway to do this?
Unfortunately, no such feature has been developed on the SAA. You need to deceive the ASA with a host located in the "interesting" part of the network to constantly generate interesting traffic. Here are a few suggestions:
-Use the IP SLA on a Cisco device
-Perform a host TCP ping
-Setting up a host of the site has press site B as a NTP source ASA
Thank you for evaluating useful messages!
-
the traffic in a vpn site-to-site tunnel restrictions
Hello
I have install a VPN site-to site between an ASA 5550 7.2 (3) and the external network of the contractor. I have set up the VPN using the wizard and it worked fine. The wizard has created the cryptomap acl see below
outside_2_cryptomap list extended access allowed object-group ip 10.0.0.0 LOCAL_IPS 255.255.255.0
where LOCAL_IPS is a group of objects containing our local subnets to be dug and 10.0.0.0/24 is the network of the remote end.
I'm trying to restrict the traffic tunnel at about 6 tcp ports, so I changed the acl (using the GUI as well from the CLI) to the following:-
outside_2_cryptomap list extended access permitted tcp object-group LOCAL_IPS 10.0.0.0 255.255.255.0 PERMITTED_TRAFFIC object-group
where PERMITTED_TRAFFIC is a group of TCP services containing the ports we'd like to tunnel.
As soon as I apply this acl (applied at the other end also) the tunnel down and or end it can re - open.
My question is - how do you restrict what traffic (tcp ports) that you want to send in the tunnel on the SAA?
Thank you
Andy
You have 2 options.
VPN-filter
Or something like that...
No sysopt permi-vpn connection
list of access vpn extended permitted tcp object-group LOCAL_IPS 10.0.0.0 255.255.255.0 PERMITTED_TRAFFIC object-group
list of vpn access deny ip 10.0.0.0 LOCAL_IPS object-group 255.255.255.0
extended vpn allowed any one ip access list
group-access vpn in interface inside
-
Hi all
I have a very weird problem (at least for me)
I have a UC520 connected to an ASA5510 via the VPN Site to Site.
I can ping from clients behind customer UC520 behind ASA5510.
I can ping from clients behind ASA5510 customer behind UC520
I can access services (such as RDP) clients behind customer UC520 behind ASA5510
I can't go to services (such as RDP, HTTP) clients behind customer ASA5510 behind UC520
Does anyone have an idea where I should look? I tried to remove any access list by (temporarily) to a permit ip everything any line in these.
I think it must be some sort of NAT problem, but I'm not sure.
Thanks in advance
You said your UC logs revealed nothing trying to connect a.11 et.12, this means that traffic is never achieved to the CPU at all, got to the UC and was abandoned before entering the LAN or traffic got to the hosts but never returned.
Internal hosts to other outgoing routes defined on them (unlikely but possible), and you can check that traffic is through the UC outside interface at least?
-
Cisco ASA 5505 VPN Site to Site
Hi all
First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..
I'd appreciate any help that can be directed to this problem please. Slowly losing my mind
Please see details below:
Two ADMS are 7.1
IOS
ASA 1
Nadia
:
ASA Version 9.0 (1)
!
hostname PAYBACK
activate the encrypted password of HSMurh79NVmatjY0
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
link Trunk Description of SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk vlan 1 native
switchport mode trunk
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan2
nameif outside
security-level 0
IP 92.51.193.158 255.255.255.252
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif servers
security-level 100
address 192.168.20.1 255.255.255.0
!
Vlan30 interface
nameif printers
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan40
nameif wireless
security-level 100
192.168.40.1 IP address 255.255.255.0
!
connection line banner welcome to the Payback loyalty systems
boot system Disk0: / asa901 - k8.bin
passive FTP mode
summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
domain-lookup DNS servers
DNS lookup domain printers
DNS domain-lookup wireless
DNS server-group DefaultDNS
Server name 83.147.160.2
Server name 83.147.160.130
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
ftp_server network object
network of the Internal_Report_Server object
Home 192.168.20.21
Description address internal automated report server
network of the Report_Server object
Home 89.234.126.9
Description of server automated reports
service object RDP
service destination tcp 3389 eq
Description RDP to the server
network of the Host_QA_Server object
Home 89.234.126.10
Description QA host external address
network of the Internal_Host_QA object
Home 192.168.20.22
host of computer virtual Description for QA
network of the Internal_QA_Web_Server object
Home 192.168.20.23
Description Web Server in the QA environment
network of the Web_Server_QA_VM object
Home 89.234.126.11
Server Web Description in the QA environment
service object SQL_Server
destination eq 1433 tcp service
network of the Demo_Server object
Home 89.234.126.12
Description server set up for the product demo
network of the Internal_Demo_Server object
Home 192.168.20.24
Internal description of the demo server IP address
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_26 object
255.255.255.192 subnet 192.168.50.0
network of the NETWORK_OBJ_192.168.0.0_16 object
Subnet 192.168.0.0 255.255.0.0
service object MSSQL
destination eq 1434 tcp service
MSSQL port description
VPN network object
192.168.50.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_24 object
192.168.50.0 subnet 255.255.255.0
service object TS
tcp destination eq 4400 service
service of the TS_Return object
tcp source eq 4400 service
network of the External_QA_3 object
Home 89.234.126.13
network of the Internal_QA_3 object
Home 192.168.20.25
network of the Dev_WebServer object
Home 192.168.20.27
network of the External_Dev_Web object
Home 89.234.126.14
network of the CIX_Subnet object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_84.39.233.50 object
Home 84.39.233.50
network of the NETWORK_OBJ_92.51.193.158 object
Home 92.51.193.158
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
the tcp destination eq ftp service object
the purpose of the tcp destination eq netbios-ssn service
the purpose of the tcp destination eq smtp service
service-object TS
the Payback_Internal object-group network
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
service-object TS
service-object, object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object RDP
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
object-group service DM_INLINE_SERVICE_5
purpose purpose of the MSSQL service
service-object RDP
service-object TS
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_6
service-object TS
service-object, object TS_Return
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
Note to outside_access_in to access list that this rule allows Internet the interal server.
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-list of FTP access
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list of SMTP access
Note to outside_access_in to access list Net Bios
Comment from outside_access_in-SQL access list
Comment from outside_access_in-list to access TS - 4400
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server
access host access-list outside_access_in note rule internal QA
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www
Notice on the outside_access_in of the access-list access to the internal Web server:
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server
Note to outside_access_in to access list rule allowing access to the demo server
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list to access MSSQL
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
Note to outside_access_in access to the development Web server access list
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
AnyConnect_Client_Local_Print deny any4 any4 ip extended access list
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137
AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns
Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0
permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
information recording console
asdm of logging of information
address record
the journaling recipient
level alerts
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
MTU 1500 printers
MTU 1500 wireless
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-711 - 52.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (wireless, outdoors) source Dynamics one interface
NAT (servers, outside) no matter what source dynamic interface
NAT (servers, external) static source Internal_Report_Server Report_Server
NAT (servers, external) static source Internal_Host_QA Host_QA_Server
NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM
NAT (servers, external) static source Internal_Demo_Server Demo_Server
NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
NAT (servers, external) static source Internal_QA_3 External_QA_3
NAT (servers, external) static source Dev_WebServer External_Dev_Web
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 84.39.233.50
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 192.168.10.0 255.255.255.0 inside
SSH 192.168.40.0 255.255.255.0 wireless
SSH timeout 5
Console timeout 0dhcpd 192.168.0.1 dns
dhcpd outside auto_config
!
dhcpd address 192.168.10.21 - 192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
paybackloyalty.com dhcpd option 15 inside ascii interface
dhcpd allow inside
!
dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
dhcpd update dns of the wireless interface
dhcpd option 15 ascii paybackloyalty.com wireless interface
dhcpd activate wireless
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal Payback_VPN group strategy
attributes of Group Policy Payback_VPN
VPN - 10 concurrent connections
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
attributes of Group Policy DfltGrpPolicy
value of 83.147.160.2 DNS server 83.147.160.130
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
internal GroupPolicy_84.39.233.50 group strategy
attributes of Group Policy GroupPolicy_84.39.233.50
VPN-tunnel-Protocol ikev1, ikev2
Noelle XB/IpvYaATP.2QYm username encrypted password
Noelle username attributes
VPN-group-policy Payback_VPN
type of remote access service
username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
Éanna attributes username
VPN-group-policy Payback_VPN
type of remote access service
Michael qpbleUqUEchRrgQX of encrypted password username
user name Michael attributes
VPN-group-policy Payback_VPN
type of remote access service
username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
user name Danny attributes
VPN-group-policy Payback_VPN
type of remote access service
Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
user name Aileen attributes
VPN-group-policy Payback_VPN
type of remote access service
Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
Aidan username attributes
VPN-group-policy Payback_VPN
type of remote access service
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
shane.c iqGMoWOnfO6YKXbw encrypted password username
username shane.c attributes
VPN-group-policy Payback_VPN
type of remote access service
Shane uYePLcrFadO9pBZx of encrypted password username
user name Shane attributes
VPN-group-policy Payback_VPN
type of remote access service
username, encrypted James TdYPv1pvld/hPM0d password
user name James attributes
VPN-group-policy Payback_VPN
type of remote access service
Mark yruxpddqfyNb.qFn of encrypted password username
user name brand attributes
type of service admin
username password of Mary XND5FTEiyu1L1zFD encrypted
user name Mary attributes
VPN-group-policy Payback_VPN
type of remote access service
Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
Massimo username attributes
VPN-group-policy Payback_VPN
type of remote access service
type tunnel-group Payback_VPN remote access
attributes global-tunnel-group Payback_VPN
VPN1 address pool
Group Policy - by default-Payback_VPN
IPSec-attributes tunnel-group Payback_VPN
IKEv1 pre-shared-key *.
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 General-attributes
Group - default policy - GroupPolicy_84.39.233.50
IPSec-attributes tunnel-group 84.39.233.50
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the pptp
inspect the rsh
inspect the rtsp
inspect the sip
inspect the snmp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect xdmcp
inspect the icmp error
inspect the icmp
!
service-policy-international policy global
192.168.20.21 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1ASA 2
ASA Version 9.0 (1)
!
Payback-CIX hostname
activate the encrypted password of HSMurh79NVmatjY0
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
Description this port connects to the local network VIRTUAL 100
switchport access vlan 100
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 100
!
interface Ethernet0/4
switchport access vlan 100
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport access vlan 100
!
interface Ethernet0/7
switchport access vlan 100
!
interface Vlan2
nameif outside
security-level 0
IP 84.39.233.50 255.255.255.240
!
interface Vlan100
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
banner welcome to Payback loyalty - CIX connection line
passive FTP mode
summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
DNS server-group defaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the host-CIX-1 object
host 192.168.100.2
Description This is the VM server host machine
network object host-External_CIX-1
Home 84.39.233.51
Description This is the external IP address of the server the server VM host
service object RDP
source between 1-65535 destination eq 3389 tcp service
network of the Payback_Office object
Home 92.51.193.158
service object MSQL
destination eq 1433 tcp service
network of the Development_OLTP object
Home 192.168.100.10
Description for Eiresoft VM
network of the External_Development_OLTP object
Home 84.39.233.52
Description This is the external IP address for the virtual machine for Eiresoft
network of the Eiresoft object
Home 146.66.160.70
Contractor s/n description
network of the External_TMC_Web object
Home 84.39.233.53
Description Public address to the TMC Web server
network of the TMC_Webserver object
Home 192.168.100.19
Internal description address TMC Webserver
network of the External_TMC_OLTP object
Home 84.39.233.54
External targets OLTP IP description
network of the TMC_OLTP object
Home 192.168.100.18
description of the interal target IP address
network of the External_OLTP_Failover object
Home 84.39.233.55
IP failover of the OLTP Public description
network of the OLTP_Failover object
Home 192.168.100.60
Server failover OLTP description
network of the servers object
subnet 192.168.20.0 255.255.255.0
being Wired network
192.168.10.0 subnet 255.255.255.0
the subject wireless network
192.168.40.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the Eiresoft_2nd object
Home 137.117.217.29
Description 2nd Eiresoft IP
network of the Dev_Test_Webserver object
Home 192.168.100.12
Description address internal to the Test Server Web Dev
network of the External_Dev_Test_Webserver object
Home 84.39.233.56
Description This is the PB Dev Test Webserver
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_2
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_3
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_4
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_5
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_6
service-object MSQL
service-object RDP
the Payback_Intrernal object-group network
object-network servers
Wired network-object
wireless network object
object-group service DM_INLINE_SERVICE_7
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_8
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_9
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_10
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_11
service-object RDP
the tcp destination eq ftp service object
outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1
Note to access list OLTP Development Office of recovery outside_access_in
outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group
Comment from outside_access_in-access Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group
Note to outside_access_in access to OLTP for target recovery Office Access list
outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group
Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server
outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group
Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft
outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group
Note to outside_access_in access from the 2nd IP Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group
outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source CIX-host-1 External_CIX-host-1
NAT (inside, outside) static source Development_OLTP External_Development_OLTP
NAT (inside, outside) static source TMC_Webserver External_TMC_Web
NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP
NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover
NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 92.51.193.156 255.255.255.252 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 92.51.193.158
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 92.51.193.156 255.255.255.252 outside
SSH timeout 5
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal GroupPolicy_92.51.193.158 group strategy
attributes of Group Policy GroupPolicy_92.51.193.158
VPN-tunnel-Protocol ikev1, ikev2
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 General-attributes
Group - default policy - GroupPolicy_92.51.193.158
IPSec-attributes tunnel-group 92.51.193.158
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHello
There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.
All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.
Here are a few suggestions on what to change
ASA1
Minimal changes
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.
Other suggestions
These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.
PAT-SOURCE network object-group
source networks internal PAT Description
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
no nat (wireless, outdoors) source Dynamics one interface
no nat (servers, outside) no matter what source dynamic interface
The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.
Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.
network of the SERVERS object
subnet 192.168.20.0 255.255.255.0
network of the VPN-POOL object
192.168.50.0 subnet 255.255.255.0
NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL
no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
ASA2
Minimal changes
the object of the LAN network
255.255.255.0 subnet 192.168.100.0
being REMOTE-LAN network
192.168.10.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM.
Other suggestions
PAT-SOURCE network object-group
object-network 192.168.100.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.
Hope this makes any sense and has helped
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
VPN site to Site from one-way data (need help)
Hello
Scenario:
VPN site to Site with Cisco 837 routers:
Place: Clients and printers
Site B: server queues and Print
Site A can communicate via VPN using RDP to site B, very well.
Question:
Site B cannot send print jobs to printers on the Site A. also unable to telnet and other access devices on the Site A of the Site (B) Pings work correctly but to all devices.
Debugging on site an access-list 110 showed no response traffic to the Site B via the VPN?
I tried change ip tcp adjust 1452 but not good...
Attached configs.
An IOS - c837-k9o3y6 - mz.123 - 4.T3.bin site
SITE B IOS - c837-k9o3sy6 - mz.123 - 2.XC2.bin
Any help would be appreciated.
Thank you very much...
Thank you for including the configs and IOS versions. Looks like you hit a bug known to FW IOS (http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCec78231&Submit=Search), you can perform debugging as described in details to see for sure. It is difficult to understand what router would be the culprit in a scenario when both run on a tunnel L2L CBAC, but probably RouterA is dropping packets. This would also explain why pings work but TCP connections are not.
I would upgrade TWO routers to be the same version anyway, you encounter far fewer problems in this way, but make sure that you upgrade to one fixed-In version (or later version), has to work around the problem.
-
VPN site to Site with restrictions (vpn-filter)
VPN site to site, I installed and it works fine and two site can meet but I question after the vpn enforcement - run under Group Policy
restrict users in the local site for dial-up networking with specific tcp ports, the vpn does not not like after order question «sh l2l vpn-sessiondb»
This works but users can't access something in the remote site
Note > after rising online in ACL at the end with this
US_SITE ip access list allow a whole
new to works well again
example of a line of Access-List
US_SITE list extended access permit tcp host 10.68.22.50 host 192.168.10.23 HTTP_HTTPS object-group
US_SITE list extended access permit tcp host 10.68.22.50 host 192.168.10.24 HTTP_HTTPS object-grouplocal network: 10.68.22.50
remote network: 192.168.10.24
is that correct or not?
attributes of the strategy group x.x.x.x
value of VPN-filer US_SITEtunnel-group General y.y.y.y
x.x.x.x by default-group-policyNote: allowed sysopt active vpn connection
The syntax on ACL that is used as a vpn-filter is different from what is normally expected. These VPN filters is not a direction, it should be noted the traffic we want to allow incoming and outgoing of the VPN in an ACL. The syntax for this is:
access-list X permit/deny REMOTE-DEFINITION LOCAL-DEFINITION
Example: You want to allow local users to access the RDP on the remote site:
access-list VPN-ACL permit tcp host 192.168.10.24 eq 3389 10.68.22.0 255.255.255.0
Disadvantage: This is all really confusing, and you can't afford things like Ping in one direction. -
Problem with the VPN site to site for the two cisco asa 5505
Starting with cisco asa. I wanted to do a vpn site-to site of cisco. I need help. I can't ping from site A to site B and vice versa.
Cisco Config asa1
interface Ethernet0/0
switchport access vlan 1
!
interface Ethernet0/1
switchport access vlan 2
!
interface Vlan1
nameif outside
security-level 0
IP address 172.xxx.xx.4 255.255.240.0
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.60.2 255.255.255.0
!
passive FTP mode
network of the Lan_Outside object
192.168.60.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
network of the NETWORK_OBJ_192.168.60.0_24 object
192.168.60.0 subnet 255.255.255.0
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_2
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_3
ip protocol object
icmp protocol object
Access extensive list ip 192.168.60.0 Outside_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
Inside_access_in list extended access allow DM_INLINE_PROTOCOL_2 of object-group a
network of the Lan_Outside object
NAT (inside, outside) interface dynamic dns
Access-group Outside_access_in in interface outside
Inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 172.110.xx.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
Enable http server
http 192.168.60.0 255.255.255.0 inside
http 96.xx.xx.222 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto Outside_map 1 corresponds to the address Outside_cryptomap
card crypto Outside_map 1 set peer 96.88.75.222
card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
inside access managementdhcpd address 192.168.60.50 - 192.168.60.100 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
internal GroupPolicy_96.xx.xx.222 group strategy
attributes of Group Policy GroupPolicy_96.xx.xx.222
VPN-tunnel-Protocol ikev1, ikev2
username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
tunnel-group 96.xx.xx.222 type ipsec-l2l
tunnel-group 96.xx.xx.222 General-attributes
Group - default policy - GroupPolicy_96.xx.xx.222
96.XX.XX.222 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Cisco ASA 2 config
interface Ethernet0/0
switchport access vlan 1
!
interface Ethernet0/1
switchport access vlan 2
!
interface Vlan1
nameif outside
security-level 0
IP address 96.xx.xx.222 255.255.255.248
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.1.254 255.255.255.0
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the Lan_Outside object
subnet 192.168.1.0 255.255.255.0
network of the NETWORK_OBJ_192.168.60.0_24 object
192.168.60.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_2
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_3
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_4
ip protocol object
icmp protocol object
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_2 of object-group 192.168.1.0 255.255.255.0 192.168.60.0 255.255.255.0
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
Inside_access_in list extended access allow DM_INLINE_PROTOCOL_4 of object-group a
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.60.0_24 NETWORK_OBJ_192.168.60.0_24 non-proxy-arp-search of route static destination
!
network of the Lan_Outside object
dynamic NAT (all, outside) interface
Access-group Outside_access_in in interface outside
Inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 96.xx.xx.217 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 172.xxx.xx.4 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto Outside_map 1 corresponds to the address Outside_cryptomap
card crypto Outside_map 1 set peer 172.110.74.4
card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0dhcpd address 192.168.1.50 - 192.168.1.100 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
internal GroupPolicy_172.xxx.xx.4 group strategy
attributes of Group Policy GroupPolicy_172.xxx.xx.4
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
tunnel-group 172.xxx.xx.4 type ipsec-l2l
tunnel-group 172.xxx.xx.4 General-attributes
Group - default policy - GroupPolicy_172.xxx.xx.4
172.xxx.XX.4 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
inspect the httpFor IKEv2 configuration: (example config, you can change to encryption, group,...)
-You must add the declaration of exemption nat (see previous answer).
-set your encryption domain ACLs:
access-list-TRAFFIC IPSEC allowed extended LOCAL REMOTE - LAN LAN ip
-Set the Phase 1:
Crypto ikev2 allow outside
IKEv2 crypto policy 10
3des encryption
the sha md5 integrity
Group 5
FRP sha
second life 86400-Set the Phase 2:
Crypto ipsec ikev2 ipsec IKEV2-PROPOSAL
Esp aes encryption protocol
Esp integrity sha-1 protocol-set the Group of tunnel
tunnel-group REMOTE-PUBLIC-IP type ipsec-l2l
REMOTE-PUBLIC-IP tunnel-group ipsec-attributes
IKEv2 authentication remote pre-shared-key cisco123
IKEv2 authentication local pre-shared-key cisco123-Define the encryption card
address for correspondence CRYPTOMAP 10 - TRAFFIC IPSEC crypto map
card crypto CRYPTOMAP 10 peer set REMOTE-PUBLIC-IP
card crypto CRYPTOMAP 10 set ipsec ikev2-IKEV2-PROPOSAL
CRYPTOMAP interface card crypto outside
crypto isakmp identity addressOn your config, you have all these commands but on your VPN config, you mix ikev1 and ikev2. You have also defined political different ikev2. Just do a bit of cleaning and reached agreement on a 1 strategy for the two site (encryption, hash,...)
Thank you
-
IPSec VPN Site-to-Site router Cisco 837 to Firewall FortiGate 200 has
I had a challege for a site to site vpn scenario that may need some brainstorming you guys.
So far, I have had a prior configuration planned for this scenario, but I'm not very sure if the tunnel I created will work because I did not test it before with this scenario. I'll go next week on this project and hopefully get a solution of brainstorming you guys. Thanks in advance!
Network diagram:
http://cjunhan.multiply.com/photos/hi-res/5/3?xurl=%2Fphotos%2Fphoto%2F5%2F3
Challenge:
(1) configure CISCO R3 IPSec Site to Site VPN between 172.20.10.0 and 10.20.20.0 using cryptographic cards
(2) IKE Phase I MainMode, lifetime 28000, md5, DH-Group1
IKE Phase II: des-esp, hmac-md5, tunnel mode
PSK: sitetositevpn
Here is my setup for review:
crypto ISAKMP policy 10
the BA
preshared authentication
Group 1
md5 hash
ISAKMP crypto key sitetositevpn address 210.x.x.66
!
Crypto ipsec transform-set esp - esp-md5-hmac ciscoset
!
infotelmap 10 ipsec-isakmp crypto map
the value of 210.x.x.66 peer
Set transform-set ciscoset
match address 111
!
!
interface Ethernet0
3 LAN description
IP 10.20.20.1 255.255.255.0
IP nat inside
servers-exit of service-policy policy
Hold-queue 100 on
!
ATM0 interface
no ip address
ATM vc-per-vp 64
No atm ilmi-keepalive
DSL-automatic operation mode
!
point-to-point interface ATM0.1
IP address 210.x.20.x.255.255.252
no ip redirection<-- disable="">-->
no ip unreachable<-- disable="" icmp="" host="" unreachable="">-->
no ip proxy-arp<-- disables="" ip="" directed="">-->
NAT outside IP
PVC 8/35
aal5snap encapsulation
!
!
IP nat inside source list 102 interface ATM0.1 overload
IP classless
IP route 0.0.0.0 0.0.0.0 ATM0.1
IP route 0.0.0.0 0.x.0.x.190.60.66
no ip http secure server
!
Note access-list 102 NAT traffic
access-list 102 permit ip 10.20.20.0 0.0.0.255 any
!
access-list 111 note VPN Site-to-Site 3 LAN to LAN 2 network
access-list 111 allow 0.0.0.x.x.10.0 ip 10.20.20.0 0.0.0.255
Kind regards
Junhan
Hello
Three changes required in this configuration.
(1) change the NAT-list access 102 as below:
access-list 102 deny ip 10.20.20.0 0.0.0.255 172.20.10.0 0.0.0.255
access-list 102 permit ip 10.20.20.0 0.0.0.255 any
(2) place the card encryption on interface point-to-point ATM.
(3) remote all of a default route.
Thank you
Mustafa
-
Tunnel VPN site to Site with 2 routers Cisco 1921
Hi all
So OK, I'm stumped. I create much s2s vpn tunnels before, but this one I just can't go there. It's just a tunnel VPN Site to Site simple using pre-shared keys. I would appreciate it if someone could take a look at our configs for both routers running and provide a comment. This is the configuration for both routers running. Thank you!
Router 1
=======
Current configuration: 4009 bytes
!
! Last configuration change at 19:01:31 UTC Wednesday, February 22, 2012 by asiuser
!
version 15.0
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
SJWHS-RTRSJ host name
!
boot-start-marker
boot-end-marker
!
!
No aaa new-model
!
!
!
!
No ipv6 cef
IP source-route
IP cef
!
!
DHCP excluded-address 192.168.200.1 IP 192.168.200.110
DHCP excluded-address IP 192.168.200.200 192.168.200.255
!
IP dhcp POOL SJWHS pool
network 192.168.200.0 255.255.255.0
default router 192.168.200.1
10.10.2.1 DNS server 10.10.2.2
!
!
no ip domain search
IP-name 10.10.2.1 Server
IP-name 10.10.2.2 Server
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki trustpoint TP-self-signed-236038042
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 236038042
revocation checking no
rsakeypair TP-self-signed-236038042
!
!
TP-self-signed-236038042 crypto pki certificate chain
certificate self-signed 01
30820241 308201AA A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
8B1E638A EC
quit smoking
license udi pid xxxxxxxxxx sn CISCO1921/K9
!
!
!
redundancy
!
!
!
!
crypto ISAKMP policy 10
md5 hash
preshared authentication
ISAKMP crypto key presharedkey address 112.221.44.18
!
!
Crypto ipsec transform-set esp-3des esp-md5-hmac IPSecTransformSet1
!
map CryptoMap1 10 ipsec-isakmp crypto
defined by peer 112.221.44.18
game of transformation-IPSecTransformSet1
match address 100
!
!
!
!
!
interface GigabitEthernet0/0
192.168.200.1 IP address 255.255.255.0
automatic duplex
automatic speed
!
!
interface GigabitEthernet0/1
Description wireless bridge
IP 172.17.1.2 255.255.255.0
automatic duplex
automatic speed
!
!
interface FastEthernet0/0/0
Verizon DSL description for failover of VPN
IP 171.108.63.159 255.255.255.0
automatic duplex
automatic speed
card crypto CryptoMap1
!
!
!
Router eigrp 88
network 172.17.1.0 0.0.0.255
network 192.168.200.0
redistribute static
passive-interface GigabitEthernet0/0
passive-interface FastEthernet0/0/0
!
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP route 0.0.0.0 0.0.0.0 172.17.1.1
IP route 112.221.44.18 255.255.255.255 171.108.63.1
!
access-list 100 permit ip 192.168.200.0 0.0.0.255 10.10.0.0 0.0.255.255
!
!
!
!
!
!
control plan
!
!
!
Line con 0
Synchronous recording
local connection
line to 0
line vty 0 4
exec-timeout 30 0
Synchronous recording
local connection
transport input telnet ssh
!
Scheduler allocate 20000 1000
end
=======
Router 2
=======
Current configuration: 3719 bytes
!
! Last configuration change at 18:52:54 UTC Wednesday, February 22, 2012 by asiuser
!
version 15.0
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
SJWHS-RTRHQ host name
!
boot-start-marker
boot-end-marker
!
logging buffered 1000000
!
No aaa new-model
!
!
!
!
No ipv6 cef
IP source-route
IP cef
!
!
!
!
no ip domain search
!
Authenticated MultiLink bundle-name Panel
!
!
Crypto pki trustpoint TP-self-signed-3490164941
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 3490164941
revocation checking no
rsakeypair TP-self-signed-3490164941
!
!
TP-self-signed-3490164941 crypto pki certificate chain
certificate self-signed 01
30820243 308201AC A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
EA1455E2 F061AA
quit smoking
license udi pid xxxxxxxxxx sn CISCO1921/K9
!
!
!
redundancy
!
!
!
!
crypto ISAKMP policy 10
md5 hash
preshared authentication
ISAKMP crypto key presharedkey address 171.108.63.159
!
86400 seconds, duration of life crypto ipsec security association
!
Crypto ipsec transform-set esp-3des esp-md5-hmac IPSecTransformSet1
!
map CryptoMap1 10 ipsec-isakmp crypto
defined by peer 171.108.63.159
game of transformation-IPSecTransformSet1
match address 100
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
automatic duplex
automatic speed
!
!
interface GigabitEthernet0/0.1
encapsulation dot1Q 1 native
IP 10.10.1.6 255.255.0.0
!
interface GigabitEthernet0/1
IP 172.17.1.1 255.255.255.0
automatic duplex
automatic speed
!
!
interface FastEthernet0/0/0
IP 112.221.44.18 255.255.255.248
automatic duplex
automatic speed
card crypto CryptoMap1
!
!
!
Router eigrp 88
Network 10.10.0.0 0.0.255.255
network 172.17.1.0 0.0.0.255
redistribute static
passive-interface GigabitEthernet0/0
passive-interface GigabitEthernet0/0.1
!
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP route 0.0.0.0 0.0.0.0 112.221.44.17
!
access-list 100 permit ip 10.10.0.0 0.0.255.255 192.168.200.0 0.0.0.255
!
!
!
!
!
!
control plan
!
!
!
Line con 0
Synchronous recording
local connection
line to 0
line vty 0 4
exec-timeout 30 0
Synchronous recording
local connection
transport input telnet ssh
!
Scheduler allocate 20000 1000
end
When the GRE tunnel carries your traffic to private ip range, your ACL must contain address of the host of point to point the IPSec tunnel.
Since then, both routers are running EIGRP in the corporate network, let the EIGRP Exchange routes via GRE tunnel, which is a good practice, rather than push the ip ranges private individual through the IPSec tunnel.
Let me know, if that's what you want.
Thank you
-
VPN site-to-site initiated in one direction
Hello. We try to establish a VPN site-to site between two ASA firewalls, let's call them ASA1 and ASA2. Problem is that ASA1 cannot start the connection. ISAKMP of ASA1 packets reach ASA2, but removed by an unwritten rule.
When ASA2 launches, everything is OK. And while the stream exists on ASA2, ASA1 use flow, so he can start VPN also.
Here's the output of packet - trace on ASA2:
ASA2 # packet - trace entry outside udp ASA1_IP isakmp ASA2_IP isakmp detailed
Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xaffd1bc8, priority = 13, area = capture, deny = false
hits = 14830976, user_data = 0xaee75a18, cs_id = 0 x 0, l3_type = 0 x 0
Mac SRC = 0000.0000.0000, mask is 0000.0000.0000
DST = 0000.0000.0000 Mac, mask is 0000.0000.0000
input_ifc = out, output_ifc = anyPhase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit rule
Additional information:
Direct flow from returns search rule:
ID = 0xae06b0c0, priority = 1, domain = allowed, deny = false
hits = 16921285389, user_data = 0 x 0, cs_id = 0 x 0, l3_type = 0 x 8
Mac SRC = 0000.0000.0000, mask is 0000.0000.0000
DST = 0000.0000.0000 Mac, mask is 0100.0000.0000
input_ifc = out, output_ifc = anyPhase: 3
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
identity of ASA2_IP 255.255.255.255Phase: 4
Type: ACCESS-LIST
Subtype:
Result: DECLINE
Config:
Implicit rule
Additional information:
Direct flow from returns search rule:
ID = 0xad731f30, priority = 0, domain = allowed, deny = true
hits = 60834932, user_data = 0 x 9, cs_id = 0 x 0, use_real_addr, flags = 0 x 1000, protocol = 0
IP/ID=0.0.0.0 SRC, mask is 0.0.0.0, port = 0
IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, dscp = 0 x 0
input_ifc = out, output_ifc = anyResult:
input interface: outdoors
entry status: to the top
entry-line-status: to the top
the output interface: NP identity Ifc
the status of the output: to the top
output-line-status: to the top
Action: drop
Drop-reason: flow (acl-drop) is denied by the configured ruleASA1 added to inbound ACL on the external interface of the ASA2 did not help. Using tracers of package in ASDM has not point to any specific rule, he just showed the entire list of the ACL rules. Using asp-menu type capture displays the reason of gout as packet-tracer, without more details. ASA2 layout only response did not help.
How to interpret the values of phase 4, i.e. to find the rule that causes drops, based on the id and other data? There is no such id in HS to access lists.
Any other ideas? Thank you very much.
And an idea more :)
Maybe you have something like this on ASA2:
Access-group outside_access_in in interface outside control plan
?
Keyword group-access-control-plan sentence, traffic, which is aimed at the interface of the ASA, may be filed. Please, see the following discussion:
https://supportforums.Cisco.com/discussion/11130691/access-group-control-plane-Cisco-pixasa
Maybe you are looking for
-
I'm on Firefox 17.0.11, if I uninstall Firefox and reinstall Firefox 17.0.11, I always get my original addons and bookmarks back? IAM short of space on my hard drive, I prefer just to re - install Firefox 17.0.11on my external hard drive, I have more
-
How to buy the extended warranty for the Satellite P840T-B684?
I bought laptop Satellite P840T-B684 in Saudi Arabia with one year international warranty that will finally now I need to extend my warranty soon, but now I am in India. The service center in our area said that you should contact the shop were you bo
-
Re: Need drivers for Satellite M40x
Hello I have a big problem... I can't find drivers for my Toshiba Satellite M40x 267 (PSM4XE-03401UFR).Please I need these drivers (for all... mother board driver etc. and especially for the display). Thank you, if it's possible a mail to eugenseverl
-
How to fix paper jamming
-
replace characters in the string
Hi all Is it possible to index the characters in a string as if it were a table and remove them from the second position and now. I just want with the first letter or number so that I can later concatenate strings to it. Thanks for any help! -Michael