workspace2.1 configure a directory in the wizard

Similar Questions

• After you have configured Anyconnect using the client of the wizard is unable to connect to Internet

  Hello

  I have a small Setup w/8.4 ASA - 5520. Outside goes to Internet, the inside is 172.17.0.0/16 network and management is 172.17.2.0/24. VPN IP pool is 172.17.8.0/24.

  After that I configured webvpn with the wizard, I have VPN into a fine, ping other IP switches and routers (ASA is running EIGRP and distributing its static route to the internet to its neighbors). I have Setup nat to allow for Internet access from the inside to the outside, use off interface as the translated source.

  After I VPN in, I am assigned a correct address for my pool VPN (172.17.8.21 for example). I can't ping or connect on the Internet however. Newspapers reveal nothing, I don't see any rejected packets. I can't reach the management either network. The management network is a switch that has all the ports of the management of the different switches, faders load, etc on this subject, but I can't access it.

  I wonder what type of NAT configuration, I have to do here and how to I'm to deny access to the Web interface and management, but nothing appears in newspapers despite debugging setup and open the firewall until completely bringing all traffic.

  The security level is 90 for the Interior and 0 to 100 outside management. The possibility of allowing equal security level interfaces pass traffic is selected. I got inside and the management to 100 before and it did not work with VPN.

  Please help, I do not have my config ASA handy ATM, but I will by hand in a few hours.

  I was wondering if anyone has recommendations on the use of NAT so I can get access, I need.

  Thanks in advance

  Patrick,

  Do not have access to an ASA myself so the commands below are not soundproof.

  But I guess if you're missing config NAT, it would be the document describing:

  https://supportforums.Cisco.com/docs/doc-11640

  To access the management, good show use some newspapers :-)

  show xlate det | I have IP_ADD (for source and destination IP)

  Show logg. I have IP_ADD (make sire logging is enabled for buffering on the level of information and to do for the source and destination)

  Marcin

• How to use a specific host directory in the ftp configuration?

  I'm restoring links in CS4 to my sites after an upgrade from Vista to 7.

  I use Go Daddy and the ability of subdirectory. I had a hard time to set up the ftp connection and I saw in another view that the directory of the host must be left blank. This actually worked. The problem is that I want to control the access of the various creators of Web sites that is contained in a hosting account. When I use the directory correct host in the Site Definition dialog box, as I did with my setup in Vista, I get the error message:

  «FTP error - could not open the remote folder [FileName] /.» Access denied. The file exists may not, or there may be a permissions problem. »

  However, the file exists. I tried various uses of oblique, in front, in the back and at the same time, without success. I don't know that there is an answer.

  Any ideas?

  Thank you

  Mark

  You can verify that your user account has access to other accounts?  Is it a reseller account where you have your own accounts or is it a box dedicated or VPS where accounts can be in different directories?  What is a Windows or Linux box

  There are a few things that could happen, but if it ends up being a permission Godaddy problem will be the only ones who can help you with that.  But just an example of a path on a Unix/Linux environment, "public_html /".  There is no leading slash, but there is a slash in the path.  If you connect to a Windows Server, it might be slightly different, but my only experience with Windows is in a network/VPN environment, so if this is your case, I'm sure someone here can help you.

• Windows XP is stuck in a loop, saying it must be enabled. I never have the wizard or it never activates.

  Activation problem

  I had to 'fix' a WinXP installation. Now I'm stuck in a loop, saying it must be enabled. I never have the wizard or it never activates. What should I do?

  It is same in 'safe mode' (I think that CTRL + ALT + DELETE)? Can you try to connect as administrator account (this account must be in "safe mode" and his name is administrator)

  If it the same - next you can try - press F8 during boot and in the menu select ' last good known Configuration":

  http://support.Microsoft.com/kb/307852/en

  LC

• When you try to connect to a wireless network I get this error: "If you want Windows to configure this connection, start the Wireless Zero Configuration service.

  original title: WiFi

  I want to connect to a wireless network on my laptop. When I go to the page of networks wirelss under the "choose a wireless network" it says "Windows cannot configure this wireless connection. If you want Windows to configure this connection, start the automatic Wireless Configuration service. My other laptop does not, and I don't know how to make the wireless network options appear. Any help is appreciated!

  Hi AshleyHenley,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?

  See the article and run the Fixit tool available, check if it helps.

  Error message when you try to run the Network Setup Wizard update for Windows XP Service Pack 2, Service Pack 3, or Windows XP Tablet PC 2005 Edition wireless

  http://support.Microsoft.com/kb/871122

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

• Speech recognition error message: "The wizard could not start."

  I want to know how to make speech recognition, but I get this message when I click on "Launch speech recognition" in the control panel.  Also get the same message when I click on 'Set Up Microphone'.

  I don't have a microphone hooked up to that time.  That I should?

  Message: The wizard cannot start.     Make sure that your audio hardware is not working properly and you check audio configuration in the control panel to control Audio devices and sound themes.
  
  I don't know what the message refers to.

  Can you help me?

  Debbie

  Of course, you must connect your microphone so that you can be the boss of your PC! ;)

• How to disable the user directory in the SSP?

  Hello

  Must turn off (do not delete) the directory of the user in the common Services of Hyperion. We use the Hyperion version 9.3.1. Is there a way we can do that?

  Thank you

  S

  Of the 9.3.1 docs:

  "If you do not want to use a configured user directory that has been used for supply, remove it from the search order so that the directory of the user is not wanted for users and groups. This action maintains the integrity of the information supply. It also allows you to use the directory of the user at a later date, if necessary. »

  http://docs.Oracle.com/CD/E10530_01/doc/EPM.931/html_cas_help/frameset.htm?removesearchord.htm

  See you soon

  John

  http://John-Goodwin.blogspot.com/

• How can I specify the installation directory for the packages installed on Windows clients?

  This article (Creative Cloud help |) Create or modify packages) mentions that you must specify the installation location on the command line in Windows for CC packages:

  
  

  Installation location

  The Application Manager offers you the following options for the deployment location:

  • Deploy to the default directory of the application: The default player is system unit; the default path is \Program Files in Windows/applications under Mac OS.
  • Directory to specify when the deployment: Allows users to end to specify the installation path when the package is deployed. On Mac OS, users are invited on the user interface, while on Windows, it's a command-line only option.
  • Specify directory: enter the path to the location to a specific installation location

  I have chosen "Specify the directory for the deployment" when I built the package.  I also added parameters for deployeur batch of Exceptions (Creative Cloud help |) Using Adobe deployeur Exceptions) indicating the installation location for the exceptions.

  How to access the command line options during install?

  • I tried setup.exe /?, and setup.exe -?, and the installation continues straight on the pilot of c: (small SSD drive; need to install on the 1 TB SATA drive on the HP workstation).
  • I looked for the MSI command line options, and there is not to change the installation location.

  There is a post somewhere that explains it?  I had no luck with my research in the forums on the web.

  When the "Specify the deployment directory" configuration is selected then you may need to use a deployment tool to deploy this package and need to call for the installation .msi.

  I hope that under Microsoft section can help. It has all the command line to install msi.

  http://TechNet.Microsoft.com/en-us/library/cc759262%28WS.10%29.aspx#BKMK_SetLogging

  Thank you

  Ashish

• No users in Active Directory in the Shared Services

  I have configured MSAD in Shared about, EPM 11.1.2.2 on Server 2008 R2 64-bit Windows, but no users or groups are listed.  I restarted all services of EPM and IIS.  I don't get any errors, simply nothing appear under the directory in the console of Shared Services.  How can I find out why it doesn't work?

  If you do not see users then remove the configuration of the Group probably won't do something but it does not hurt to try, if there are errors with the configuration it should be in the newspapers, are you sure that the account that you have configured the external directory with can see users, is the correct user RDN. It can be interesting to use a LDAP browser and find the same configuration to see if it recovers users, if not then you would need to discuss with someone who administers the AD.

  See you soon

  John

  http://John-Goodwin.blogspot.com/

• Configure Active Directory and form WLS and human task

  Hi guys,.
  
  We use SOA Suite 11.1.6 for the current project and want to configure Active Directory as an identity provider. I know this is not a new issue and has made several researches on the forum and online, but do not meet all of our questions. Currently, in the field of security WL, we see users and groups in the AD. But there are questions still pending:
  
  1 authentication with users of the AD
  We can not yet to configure user connection WLS AD.
  
  2. e-mail users
  The AD user does not appear in the search for email in jdeveloper. Currently, there are only two users returned: weblogic and oraclesystemuser. I think they're the default users.
  
  3 WorkList Application (human task)
  It is similar to the #1, but not all. We like to configure AD users to log on to the application of the task list.
  
  Any suggestions are appreciated.
  
  Thank you
  Steven
  
  Published by: sw12345 on April 27, 2012 11:49

  Hi Steven
  1. what you want is possible, BUT you can have your users only in a security provider. To access/bpm workspace, all users will be designated in the first highest security provider of the page. So make sure, your AD authenticator is the highest and also all of these providers must be defined on ENOUGH / OPTIONAL.

  Below, these 2 positions should give more details:
  WebLogic administrator account is inactive after activating the authenticator DB
  Re: Workspace 11g BPM don't Show no user of OVD - highest authentication provider page

  Thank you
  Ravi Jegga

• Workflow with the wizard

  I have a question about workflow, with a wizard to help me select the images to be used for a show.  Here's my current workflow.

  (1) mounting base and adjustment of images.  Reform of the obvious losers.

  (2) export images so that my assistant can rate/slaughter them.

  (3) import on sides of my assistant and use it to help determine what are the images to use.

  (4) show to create images.

  I am strugling with the best way to manage 2-3.  My assistant does not use the same computer that I do so using the same LR catalog and note using the LR library module does not work.  I would like to be able to publish in a shared directory, my assistant a tool allows to note the images here and then import it those transparent rear side in LR.  I think the API to publish has a facility to import * of * data - it can download the comments of photo sharing sites.  Can he do this?  This feature is already implemented?  Y at - it a plugin that does this?

  Does anyone have an idea of how improve this workflow?

  Thank you!

  David

  I have a LR catalog and 1000's of photos, but I have two computers that I want to work with them, so my workflow is to host the catalog and photos on a USB key drive permanently, I save on my drive internal, so I always have a copy backup of all that in the case where I drop the USB.  There is no export and import several times, just open the catalog on two different computers.  I have the USB key mapped as the same drive letter on both computers, so I don't have to mess with the remapping of the records.

  USB 3.0 portable drives are fast enough.  If it is a Mac environment I believe that there is a FireWire interface reasonably fast, too.

  ==

  However, if you want to work with pictures on the local disk, what is the problem with giving the wizard a copy of all of the LR catalog (which is relatively low compared to the size of the photos, in any case) and the range of photos via a share on their computer, allowing them to rate the photos, then simply copying the catalog back share?  Make sure the path to the pictures (and to avoid confusion, the catalog) are the same on both computers and it should work ok.  The two computers could access photos via a local drive letter, not a network share.  Just copy is made through the share.  You probably do not want to overwrite your catalog with their copy immediately in case they changed something inadvertently, but eventually you can serve additional copies on your side as serve you the backups that accumulate over time.

  If there's no privacy with what you have in your large catalog, they would not have previews or photos so would not be able to see things, just read the key words.  If it is not quite private, just segment your catalog in addition to one and put the photos that the wizard is allowed to see in a catalog that do you the above process with and let your photos more private in another catalog.

• Cannot configure DBAdapter to call the procedure that takes no parameters

  Hello
  
  I created a test as a package below:
  
  create or replace package Tester
  as
  Main1 procedure;
  procedure (x VARCHAR2) Main2;
  
  end;
  
  create or replace package body Tester
  as
  
  procedure Main1
  is
  Start
  insert into ziptest values (' Main', sysdate);
  commit;
  end;
  
  procedure (x VARCHAR2) Main2
  is
  Start
  insert into ziptest values (' in Main2 :'|| x, sysdate);
  commit;
  end;
  
  end;
  ----------------------------------------
  When I try to configure a DB adapter to call the Main1 procedure, that I'll meet with the following error:
  An error occurred while getting stored procedures. Verify that the database connection is valid.
  
  If I try to configure the DB adapter to call Main2, it works without problem.
  In addition, this occurs only when the procedure is in a package. If the procedure is independent, no error is delivered.
  
  Is this a known bug or am I missing something. I use Jdev 10.1.3.4 and SOA Suite 10.1.3.4.
  
  Kind regards
  
  Amit

  Hi Amit,

  This is a bug in the wizard of DBAdapter. Try to update BPEL for the latest available patch, and if this does not work here workaround has been tested to work on 10.1.3.1 too!

  1. modify "Main1' to"Main1 (dummy IN VARCHAR2)"in your package.
  2. use the wizard of DBAdapter as ususal to create a partner link that hits this procedure has changed.
  3. change your procedure "Main1" back to the way it was IE without any parameters.
  4. in your BPEL process file, find the file .xsd to Main1 generated by the wizard in step 2. Replace ... inside the for the "InputParameters" element with an emty tag.

  Now, go ahead and invoke this link partner as usual. It would work! ;)

  Kind regards
  Ravi

• I bought the new iphone 6 s more and I have not configured, I just opened the phone and charged, but after some time it stop by itself, is this normal or I have a problem with my phone?

  I bought the new iphone 6 s more and I have not configured, I just opened the phone and charged, but after some time it stop by itself, is this normal or I have a problem with my phone?

  You need to activate the phone. There is nothing that the phone can not be activated.

• How to change the default directory of the staff collective

  How do I change default directory of the collective of personal?

  OK so now I understand your talking about the contacts pane in the compose window. Here, I thought it was something to do with the address book. How it is difficult to click the desired address book, I really don't know. But the developers are working on a fix for the contact component to remember the address book selected between sessions, as it does now used session.

• I use MozBack to the top, when I followed the instructions of the wizard a file on my portable hard drive. I went back to Thunderbird and my Inbox was deleted

  I use MozBack to the top, when I followed the instructions of the wizard a backup file on my portable hard drive. I'm back to Thunderbird I found the content of my Inbox was deleted. Sent and deleted files have not been removed. I then returned to MozBackup and followed the instructions to restore the information from my Inbox, but it didn't happen.
  What I did wrong.

  as incredible as it may seem. MozBackup has nothing to do with Mozilla or Thunderbird. If you have any questions about mozbackup I don't really know where you're going.