1121Gs
Hiya,
does anyone know if a 1121G connect to the WDS running on a 1242AG?
Thank you
Cameron
Hello
Yes, there is no problem to bring charges against the two... the third question, the FAQ will answer your question...
http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_q_and_a_item09186a00804d4421.shtml
Let me know if this answers your question!
Concerning
Surendra
Tags: Cisco Wireless
Similar Questions
-
Multiple BSSIDs does not not on 1121G AP
Hello
I am trying to set up some 1121 G autonomous access points to play a couple of SSID - each SSID is in its own VIRTUAL LAN and it all works well when I don't use multiple BSSID.
I got to the stage where I can see all 3 broadcast SSID but I can't connect to one of them. An SSID is totally open, one is to use EAP, and the other is WPA/PSK.
Any ideas why this could happen because I'm totally distraught now... back to Radio that only one SSID and all three SSIDS working again.
I can post the config if it would help.
Thank you
Network ID must make with the help of a WLSM and tunnel traffic to the 6500. If it doesn't work without the network ID, that's fine.
-
Stand-alone 3502I without controller?
I have a client with several former Aironet 1121 G from WAP. In one place of the factory several big engine noise levels prevents a reliable connection to the WAP, even if it is located in the same room as users. I mean updated the 1121G to the 3502I to take advantage of Clean Air technology. This raises two questions:
1) will be able to effectively manage the RF noise only 3502I or it requires a WAP network to work properly?
(2) the 3502I requires the controller of CT2504 to clean at work, or it will run in stand-alone mode?
Thanks in advance,
Joe
Does that drop the connection speed down to about 1Mb/s?
NO. 802. 11A is high-speed, short-range radio. 802. 11b is long range and low speed and has 3 channels of Alcan.
Unfortunately, if you have a noisy RF environment, putting a WLC (DCA, with active PTC) can help. Without this, you need to constantly monitor each WAP and manually change the channels and Tx power.
You are in a situation a little "who comes in first place, the chicken or the egg". If you cannot afford to get a WLC with your solution, don't bother upgrading. It's a waste of money.
Maybe you are looking for
-
downloadable version for the Australia
in Australia use British version usa os
-
How can I reinstall the webcam integrated Equium L350?
Hi all I hope someone can help me with this: I get an error message with a component of the miss on it tells me to reinstall my built in webcam but I don't know how and I can't find anything on the Toshiba site?All of the software drivers are up to d
-
Satellite P300D-10U - how to enable the AHCI controller in the Bios
I have toshiba satellite P300D-10U with windows vista 32-bit, disc ssd drive 2nd hard driveand I can't do IT controller SATA AHCI in the bios. http://www.Toshiba.EU/discontinued-products/satellite-P300D-10U/ What can I do?install the new windows 7 32
-
Save data in a solo in una archivo STRUCTURE SEQUENCE PLATE
Hola! I made UN programa than controla una fuente CRYOGENIQUES SMS VI - editor, I have a problema are in Quebec no case en datos to como to you can hacer para grabar los a UNICO archivo, este momento esta recording in back. CABE pasear than what quie
-
Index beyond count and error in DML table
Hi allI really appreciate your advice regarding the below question.I have a big procedure so I can't put my procedure here, but I'll try to give you some details and maybe I can pass my problem and advice of experts with you.I have some values in the