2 cryptographic cards on the same interface

Similar Questions

• The ASA can use 2 dynamic cryptographic cards on the external interface?

  We have an ASA which is currently used with dynamic VPN. I don't know the pre-shared key.  If I was going to try to create another card encryption. I did not want to bring another drop.  I know that the router does not allow.  It would replace the existing info.  I wasn't sure of the SAA.

  David,

  The pre shared key is defined in the specific tunnel-group, not in the crypto map.

  tunnel-group ipsec-attributes

  pre-shared key cisco

  However, by default:

  Dynamics of LAN-to-LAN tunnels using the 'DefaultL2LGroup '.
  

  L2TP/IPsec connections use the 'DefaultRAGroup '.
  

  In order to see the pre shared key in clear text: "more system: run".

  You can have a single card dynamic encryption card crypto, but you can have multiple entries / map instances of this dynamic, for example:

  Crypto-map dynamic dynamic_map 10 the value transform-set ESP-AES-256-SHA
  

  Crypto-map dynamic dynamic_map 20 the value transform-set ESP-AES-192-SHA
  

  
  

  map outside_map 65535-isakmp ipsec crypto dynamic dynamic_map

  More info:

  Dynamic IPsec Tunnel between a statically addressed ASA and dynamically addressed Cisco IOS router that uses the example of Configuration of CCP

  ASA/PIX: Allow the tunneling split for the VPN Clients on the example of Configuration of ASA

  
  

  Let me know if you have any other questions.

  Portu.

• I have 6 which weighed charges on my debit card for the same Netflix subscription.

  I tried to update my information to cc without success, I might add, and now I have 6 which weighed charges on my debit card for the same Netflix subscription. He has actually decreased my debit card that has sufficient funds, and I hope that I have that I extract only, the only time. Can anyone confirm if this has happened to them before?

  Thanks in advance!

  Whenever you add or change your payment information, you are likely to receive a temporary store operating load, your card issuer should remove in a few days or more: on the payment card's authorization in the iTunes Store - Apple Support

  If the card is still declined, then the subscription will be not have been paid for. You can check with the card issuer to see if they are declining, or try another card (a card have a chance to be accepted it must be registered with the same name and address (including the format and spacing etc) that you have on your iTunes account and have been issued by a bank in the country where you are and which is therefore the country on your iTunes account).

• Need help for reading in parallel on the same interface and writing XNET

  Hello. I need help to configure CAN interface to write and read from the same interface.

  I use NI PXI-8513/2. I use CAN1 as interface.

  My had TO send status messages CAN every 100ms. I have to read in order to return akntoowlege to keep DUT CAN interface happy and not make mistakes.

  So, I want to open Strim Session and readall frames in the loop. At the same time, I need to be able to write in a frame HAD at the time...

  I only need to read one picture at a time too, but since I know the ID, I can pull it from the stream.

  What I'm confusing all is how to put in place the same CAN1 interface to be able to write and read in parallel.

  I think I would get errors that interface is already in use.

  Since I'm new to CAN, I was read and write only when necessary. But, sometimes I was getting errors on my messages. Sometimes I get message, sometimes miss me. But, when I run CAN test criminal as sniffer he sends and written every time. I was told it's because it recognizes all messages.

  I opened to suggestions of how best to implement the interface.

  I guess I can use CAN2 and separator to work around this problem, but I would use an interface if possible.

  Thank you

  Hi Rus,

  The XNET hadrware takes care of most of the low level of detials for you. The reading and writing of the circuits are both connected to the bus at any time. When you write to the hardware it will try to put a frame on the bus at the first opportunity he can. If the frame loses arbitration material re - will attempt to send the frame up is successful. Reception equipment monitor activity on the bus, regardless of what it conveys. The material received will usually throw a framework that was sent by communication equipment, but there is an Echo property pass to circumvent this behavior too.

  Take a look at the example of the expedition: MAY-> NI - XNET-> Sessions-> multiple Sessions Intro-> CAN even exit entry framework Port unique Point.vi. Keep in mind that this example you will need to use a second CAN interface to recognize frames, it transmits. I would recoment against the example CAN output Frame Single Point which would mimic your ECU if you choose a type of cyclic frame running this example.

• How to set up and use two video cards at the same time.

  I have HP Pavilion a6150d desktop under Windows XP SP3 PC. My goal is to be able to use the integrated video card and GeForce 220 video card I just buy at the same time.

  The integrated video card and GeForce video card (connected to the PCI-E) are installed and usable, but the problem is that I think that my computer cannot detect a video at a time card, so I can't use 2 monitors at the same time.  The video only card detects my computer is what I chose as a primer in the BIOS. When you go to the Device Manager display adaptors I can only find an available video card and that's regardless of Setup as primary in the BIOS.

  My GeForce 220 have VGA, DVI and HDMI display connectors, but I don't have that VGA cables. So my only option at the moment is to use my video card GeForce with band single VGA connector and integrated everyone to use my two monitors.

  I hope someone can help me without spending more money...

  "You're not going to be able to use the graphics card integrated Intel and PCIe x 16 graphics card at the same time."

  Thanks Frank, this already answered my question, you help me already by saving my time searching for the fix (since there is NO solution), although it won't save my money I like always your quick response and your support. My monitor is HPw1907 with a DVI connector, so I'll just buy a DVI cable. My other monitor LCD SHARP that have a HDMI and VGA connector so I'll just use the VGA cable in this one.

  So I guess that my simple goal is not achievable using HP Pavilion a6150d. I love HP more than Dell, but it's doable in Dell, so I hope that HP will have way on how to make this thing work in the future.

• JIT - ACM with two Instance of the Ethernet on the same interface Service

  Hi all

  I develop script of EEM for platform of ASR903... I would define VCA two, one for each 'host' connected to the same interface of ASR903 (GI 0/1).

  Each host sends CFM package, I will know which CVS the CFM package arrives. In the EEM scripting language, there are the following variable: $_ethernet_intf_name that can be used to retrieve the name of the interface. Is there another variable that can be used to recognize the VCA or is there any syslog message that conatins this information?

  CFM Ethernet ieee

  Ethernet global cfm

  field of Ethernet HOST1 level 2 cfm

  Service vlan301 evc301 evc vlan 1301 direction downwards

  continuity check

  !

  CFM Ethernet ieee

  Ethernet global cfm

  area of cfm Ethernet HOST2 level 3

  Service vlan301 evc302 evc vlan 1302 direction downwards

  continuity check

  !

  VCA evc301 Ethernet

  VCA evc302 Ethernet

  !

  interface GigabitEthernet0/1

  ink description to ASR - 903 by microwave

  no ip address

  load-interval 30

  auto negotiation

  Ethernet microwave hold sending 10 event

  Ethernet microwave wtr event 5

  Ethernet microwave-threshold of loss of 255 event

  !

  service instance 301 ethernet evc301

  encapsulation dot1q 301

  rewrite tag pop 1 symmetrical penetration

  Bridge-domain 301

  CFM mep field HOST1 mpid 101

  CFM encapsulation dot1q 301

  !

  service instance 302 ethernet evc302

  encapsulation dot1q 302

  rewrite tag pop 1 symmetrical penetration

  Bridge-domain 302

  mep field HOST2 mpid 102 cfm

  CFM encapsulation dot1q 302

  !

  Ah, ethernet OAM.  I've never used the detector of this event, so I don't know what capabilities are available.  I don't have a handy to test myself ASR903.  You can run the command "show event handler detector ethernet detail" to see what built-in variables are available to your EEM ethernet event policy.  You can also do "display event handler detector all ' to see all detectors of the event.  I hope you see something out there that specifies the VCA.

  If this isn't the case, you certainly could extract something like a syslog message if a message is generated that contains the name of EVC.  Still, I don't know what syslogs are generated, so you should test yourself.

• Can I use two cards at the same time on the same computer?

  Hello

  I have two graphics cards, one is integrated, i.e. HD 2500, Intel and the other is dedicated, i.e. Nvidia Geforce GT620. My question is that can I use both at the same time on the same PC. Whenever I try to connect via a VGA cable (per processor) and DVI (via graphic card) at the same time, the screen goes black and when I take off the DVI cable, the screen will return. When I connect the DVI again after log on, there is just the theme of Windows and folders that I opened all get reduced. When I disconnect the DVI cable once again, I opened the folder displays again.
   
  I want to make use of both integrated and dedicated graphics card, I read on the internet that two graphics cards give a performance gain. Also, I'm a gamer. But in time, I bought my PC, I had no knowledge about computers. I want to use two graphics cards. Please tell me a way by which I can use two graphics cards at the same time without the problem described above.

  Yes, you can use two cards graphics, combined to boost performance. But it depends on a condition: the two (or more) cards must be of the same brand. To make it clearer, you can use two or more NVIDIA graphics (thanks to SLI technology) or AMD graphics (with CrossFireX technology, supports up to four graphics card in a single PC).

  But, a mixture of graphics cards of different brand, as NVIDIA and AMD or NVIDIA and Intel or AMD and Intel or NVIDIA, AMD and Intel, can not be used for SLI or CrossFireX.
  On the black screen, please follow the following link:
  http://support.Microsoft.com/kb/976064

• WebVPN and anyconnect on the same interface

  Hello!!

  We have ASA 5520 firewall running with code.9.1 (2). We already have webvpn running on the firewall and has active users to use it. Now, the client came with a new requirement to configure firewalls on the same anyconnect. We have installed VPN more premium license.

  (1) is it possible to enable webvpn and anyconnect on the same interface. If Yes, what are the aspects we must consider to allow them both on the same interface?

  (2) how much webvpn and anyconnect vpn licenses should I do with my premium lincense?

  Please help on this.

  shver attached for reference.

  Best regards

  Sri

  Your peers licenses AnyConnect Premium gives you the right to access SSL VPN without customer and focused on the customer.

  Licensing is based on the concurrent users so regardless of the simultaneous dosing will work - as long as the number of connected does not exceed 100.

  Your site to site VPN IPsec does not count against this permission, but is rather against "Other peer VPNS" which does not require a separate license and is limited by the capacity of the ASA equipment (750 on your platform).

• How to get the ASA packets that come in and out on the same interface?

  Hi all

  How can I configure the ASA5520 routes the packets that come in and out on the same interface? I ve more than 1 network behind the camera of the SAA. It s separated by internal router. They can communicate with each other.

  I've seen it's PIX design problem. She applies to the platform of the ASA?

  Please advice.

  Thank you

  Nitass

  This golden rule remains immutable. the only exception is the vpn traffic. ASA for example (or pix v7) would act as a hub for traffic between two rays rediect vpn.

  regarding your question.

  Internet <-->asa <-->1 <-->lan router <-->lan 2

  assuming the host to lan 1 to asa as the gateway default, even asa has a static route to the internal router of the point for local network 2, the golden rule will reject this operation.

  one solution is to re - configure the dhcp on the LAN 1 scope and make the internal router as the default gateway; and the internal router has the asa as the default gateway.

• Site-to-site and VPN Client on the same interface

  Hello

  Maybe it's a simple qeustion, and I also know it can be done on a SAA.

  But is it possible to have ipsec-l2l tunnels and external client ipsec VPN on the same interface on a router? If so someone can give me a link on how to do it because I can't find 1.

  Thank you

  Here you go:

  http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a00809c7171.shtml

  Hope that helps.

• My lightroom is having problems to import images, I tried a different card with the same results readers

  My lightroom/mac is having problems to import images, I tried a different card with the same results readers

  This means that ccouldn can't ccopy Lightroom photos in the destination directory. You must determine which directory is specified in the Lightroom Import dialog box, it is on the right in the Destination. Then, you will need to enter your operating system and change the permissions on this specific issue to the WRITE permission.

• Loading multiple files using the same interface in ODI

  Hi all
  
  We load multiple files using the same interface and get the error "java.sql.SQLException: ORA-00942: table or view does not exist" while inserting record in the staging table. It looks like the same temporary table is used when loading multiple files and the error. Grateful if someone offers a solution to avoid this error.
  We use the following KMS:
  
  (1) LKM SQL file
  (2) IKM Oracle SQL COMMAND append.
  
  Receive a quick response.
  
  Thank you
  RP

  Hello

  See this http://odiexperts.com/interface-parallel-execution-a-new-solution

  Thank you
  Fati

• GRE and IPSEC VPN tunnel over the same interface

  My client is currently connected to a service provider of call through a GRE Tunnel over IPSEC. They chose to move all connections to a VPN site-to-site traditional behind a firewall, here, to your corp office.  As the questions says, is possible for me to put in place the VPN site to site on the same router? Interface Tunnelx both ethernet have the same encryption card assigned to the destination router.  I thought that traffic could divide by identification of traffic 'interesting '.  Thanks for all the ideas, suggestions

  Ray

  Ray

  Thanks for the additional information. It takes so that the existing entries in ACL 101 remain so the existing tunnel will still work. And you have to add entries that will allow the new tunnel. Editing an ACL that is actively filtering traffic can get complicated. Here is a technique that I use sometimes.

  -create a new access list (perhaps ACL 102 assuming that 102 is not already in use).

  -Copy the entries of ACL 101 to 102 and add additional entries you need in places appropriate in the ACL.

  -Once the new version of the ACL is complete in the config, then go tho the interface and change the ip access-group to point to the new ACL.

  This provides a transition that does not affect traffic. And he made it back to the original easy - especially if something does not work as expected in the new ACL.

  If the encryption of the remote card has an entry for GRE and a separate entrance for the IPSec which is a good thing and should work. I guess card crypto for GRE entry specifies an access list that allows the GRE traffic and for IPSec crypto map entry points to a different access list that identifies the IP traffic is encrypted through the IPSec tunnel.

  HTH

  Rick

• VMware device with 2 network cards claiming the same IP address with two MAC addresses

  Hello.

  I see messages intermittent my gateway network two MAC addresses associated with a virtual machine running on a 5.5 ESXi host for the same IP address.

  The virtual machine is a MiTel 3300 controller for a VOIP system. the system is configured with two IP addresses, one on the local network and another with a public IP address in the DMZ. In the network configuration of the 3300, I assigned the address LAN IP at 00: 0C: 29:30:B2:B2 and the DMZ IP at 00: 0C: 29:30:B2:BC (Mac for network devices presented by the ESXi host virtual machine).

  On the host, I configured a vSwitch with exclusive access to two physical network adapters on the host machine. The vSwitch is configured with two machine virtual port groups, LAN and DMZ, with access to the physical network interface cards. Tab grouping of groups vSwitch port NIC, I replaced the order of failover of the switch to activate an active NETWORK card only for the Group of LAN ports and the other card NETWORK only for the DMZ port group. (I don't know how the content of the column of networks is determined. Neither is correct for the traffic on the physical switch. If these are configurable, please advise and I'll change the settings). The relevant parameters of vSwitch, groups of ports and VM are distinguished below.

  On the virtual machine itself, through the VMWare host, I assigned 00: 0C: 29:30:B2:B2 for the Group of LAN ports and 00: 0C: 29:30:B2:BC to the DMZ group port (best I can tell, anyway, since the MAC address field annoyingly obscures the last two digits of the MAC address - break if I invert the mapping) (, but all seems OK).

  The goal here is to make sure that MACs of ports vSwitch the 3300 is listening and sending always correspond to the physical ports that are VLAN Tag by the physical switch to ensure the routing. Generally speaking, it seems that what is happening but, intermittently, we cross one-way calls that suggests a problem of routing between us and our SIP trunk provider; coinciding with these incidents, I get an email along the lines of "the security in the network device has detected a conflict of IP address with two or more devices. The period of INVESTIGATION "DMZ. DMZ. DMZ. DMZ' is claimed by the following clients with MAC addresses: ' 00: 0C: 29:30:B2:B2' ' 00: 0C: 29:30:B2:BC'. »

  I did something in the configuration that would lead to this kind of collision intermittent? Have a hacked together a way to do something that could be accomplished in a way that is simpler and more reliable?

  Thanks for any idea that you can offer.

  Kind regards

  J.

  

  

  

  I probably don't fully understand your configuration, but it seems that you are not interested in using the collection of NETWORK adapters in the virtual switch of the VM MiTel 3300.

  If it is correct, why not create two virtual switches, each with a group of port (LAN and DMZ) unique and with a separate connection of (vmnic2 and vmnic1)?

  In general, collection of NETWORK adapters may be used to share traffic between uplinks and ensure that if one of the uplinks connect fails, a virtual machine still has access to the network.

• Using the same interface CAN read and write

  Hello.

  Can I use the same CAN interface to read and write?

  For example:

  I send you CAN frame using CAN1 to my MCU.

  IF MCU confirmed the order of receiver it immediately sends the echo return command and there different ID to send the command.

  I tried to use CAN1 output framework and then reconfigures CAN1 to frame in queue and retrieve the frame of the echo.

  But it seems that I was always missing. The 'framework of CAN' kept vi expire.

  When I used the separator on the outlet BOX in my configured MCU CAN1 for frame and CAN2 for chassis in and I managed to catch the echo framework.

  I think about 100 ms for the frame in response that will be sent after the order has been received. It takes longer for the NI PXI-8513 reconfigure? Can I still do it, or I have to use the separator?

  I wad jump to use an interface to read and write.

  Thank you

  Ok. I misread your notion of echo. I understand now. I'm sorry.  The code you posted seems reasonable.

  (1) did you notice on or off for the session?

  (2) what baud rate? You can add a parameter of baud rates for the property to be explicit node.

  (3) I don't remember the name of VI, but you can add a status of Comm Get after reading. This will give you some information about the bus - if errors were detected, etc. Which can be useful to help debug.