GRE and IPSEC VPN tunnel over the same interface
My client is currently connected to a service provider of call through a GRE Tunnel over IPSEC. They chose to move all connections to a VPN site-to-site traditional behind a firewall, here, to your corp office. As the questions says, is possible for me to put in place the VPN site to site on the same router? Interface Tunnelx both ethernet have the same encryption card assigned to the destination router. I thought that traffic could divide by identification of traffic 'interesting '. Thanks for all the ideas, suggestions
Ray
Ray
Thanks for the additional information. It takes so that the existing entries in ACL 101 remain so the existing tunnel will still work. And you have to add entries that will allow the new tunnel. Editing an ACL that is actively filtering traffic can get complicated. Here is a technique that I use sometimes.
-create a new access list (perhaps ACL 102 assuming that 102 is not already in use).
-Copy the entries of ACL 101 to 102 and add additional entries you need in places appropriate in the ACL.
-Once the new version of the ACL is complete in the config, then go tho the interface and change the ip access-group to point to the new ACL.
This provides a transition that does not affect traffic. And he made it back to the original easy - especially if something does not work as expected in the new ACL.
If the encryption of the remote card has an entry for GRE and a separate entrance for the IPSec which is a good thing and should work. I guess card crypto for GRE entry specifies an access list that allows the GRE traffic and for IPSec crypto map entry points to a different access list that identifies the IP traffic is encrypted through the IPSec tunnel.
HTH
Rick
Tags: Cisco Security
Similar Questions
-
Site-to-site and VPN Client on the same interface
Hello
Maybe it's a simple qeustion, and I also know it can be done on a SAA.
But is it possible to have ipsec-l2l tunnels and external client ipsec VPN on the same interface on a router? If so someone can give me a link on how to do it because I can't find 1.
Thank you
Here you go:
http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a00809c7171.shtml
Hope that helps.
-
Windows IPSEC and SSL VPN client on the same machine
Matches (coexistence) installation of IPSEC and SSL vpn clients that are supported on the same computer, windows (XP and Win7)?
As mentioned by Patricia and Jennifer (5 stars), you can install two clients on the same machine without any problem.
The tricky part comes when you are trying to connect two clients at the same time, that's when you may encounter unexpected problems.
However, if your intention is to install both clients and connect them individually and not at the same time, you'll be fine.
If you have any other questions, please mark this question as answered and note all messages that you have found useful.
Thank you.
Portu.
Post edited by: Javier Portuguez
-
Two VPN tunnels on the same device with the same protected networks
There is a remote site that wants me to put in place two separate tunnels of VPN with the same internal IP at each end. FOR EXAMPLE
LAN = 10.212.170.201/32, 10.212.170.202/32
Remote network 192.168.0.0/24 =
I currently have a tunnel between the above:
End Point distance = 111.93.152.186
Local endpoint point = 198.205.115.252
Now, they want to set up a VPN for the same networks between:
End Point distance = 115.115.130.34
Local endpoint point = 198.205.115.252
It is my understanding that the Cisco ASA 5520 can do. The only way I've seen this done with Cisco hardware is to use two ASAs, but there may be a way to use the costs of road or some other tricks to make it happen.
I'm open to suggestions.
Is a backup?
In, specify endpoint remote second as a "backup" of the peer in the first virtual private network. Alone will be active at the time - but there are toggled if the VPN in first dies.
-
On Pix VPN tunnel to the same subnet
I have a customer who want to set up a the PIX VPN tunnel located on each site. For some reason, each side has the same subnet number, for example. 10.10.10.x/32. I'm sure we must run NAT, but is it possible.
This can help
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800949f1.shtml
-
EasyVPN and access VPN remotely on the same box
Is it possible to have a config EasyVPN and remote access in the same box? I tried to do that and when I do a vpnclient enable command he said remote NAT (outside) 0
Router IOS or PIX? EzVPN server or client?
If it's EzVPN server, then it's basically a configuration of remote access also, then Yes, you can certainly have them both, actually just set one up and you get one anyway.
If it's EzVPN client, then no if it is a PIX and Yes if it's a router, but you must run 12.2 (15) T, see http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/ftezvpnr.htm#1155828 for more details.
Please answer back with more information on exactly what you're trying to do, it is a little difficult to your original explanation.
-
We currently have several sites with ISAKMP/IPSec tunnels between routers 2800 and we need some of them migrate to the GRE with IPSec tunnels. Are there problems with endpoint tunnels GRE and IPsec on the same router and interface?
I didn't know all the problems - apart from the router doing the encryption/decryption & GRE encapsulation/decapsulation, just be respect for traffic through the put.
I have noted problems with traffic GRE and MTU problems. Cisco recommends a MTU of 1440 at Discretion, I would say that set 1400.
HTH
-
Conflict of IPSec between IPSec and business VPN tunnels
I crushed a 2821 current c2800nm-adventerprisek9 - mz.124 - 22.YB8 at home with 2 gre IPSec tunnels for personal use, and my office will be held that a customer based IPSec VPN to connect to the corporate VPN. My problem is that when I want to connect to the corporate VPN, I see packages being encrypted and sent, but I would have never received the return packets. It seems that the IPSec VPN tunnels with IPSec from my office and router packages conflict trying to decrypt and gives this error. (I removed the public addresses for anonymity)
CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec would be package IPSEC a bad spi to destaddr = "myaddress", prot = 50, spi = 0xDB32344E (3677500494), port = "corpvpn".
When I remove the card encryption off-side WAN router, my Office VPN works immediately. I can change the configuration, either on the side of the IPSec GRE tunnels, but has no way for me to change any configuration on the corporate VPN. Does anyone know of a workaround on the cisco router? I can provide the running configs or view orders.
The 2821 also performs NAT overload for internet access.
Hello, Reed.
1. try to remove the interface crypto map and add "protection... profile ipsec tunnel." "to your VTI:
Crypto ipsec IPSEC profile
solid Set trans
int g0/0
No crypto map card
int tu1
Ipsec IPSEC protection tunnel profile
int tu2
Ipsec IPSEC protection tunnel profile
2. try to force your corpVPN to use encapsulation UDP instead of ESP.
-
VPN tunnel between the concentrator 3005 and router Cisco 827
I am trying to establish a VPN tunnel between the Central Office with VPN 3005 and controller branch Cisco 827 router.
There is a router of perimeter with access set up in front of the 3005 list.
I quote the ACLs on the Central perimeter router instructionsuivante to allow traffic to permit ip 3005 - acl 101 all 193.188.X.X (address of the hub)
I get the following message appears when I try to ping a local host in the Central site.
Can Anyoune give me the correct steps to 827 and 3005.
Thank you
CCNP Ansar.
------------------------------------------------------------------------------------------------------
Debug crypto ISAKMP
encryption of debugging engine
Debug crypto his
debug output
------------------
1d20h: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = 172.22.113.41, distance = 193.188.108.165.
local_proxy = 202.71.244.160/255.255.255.240/0/0 (type = 4),
remote_proxy = 128.128.1.78/255.255.255.255/0/0 (type = 1),
Protocol = ESP, transform = esp - esp-md5-hmac.
lifedur = 3600 s and KB 4608000,
SPI = 0x83B8AC1B (2209917979), id_conn = 0, keysize = 0, flags = 0x400D
1d20h: ISAKMP: ke received message (1/1)
1d20h: ISAKMP: 500 local port, remote port 500
1d20h: ISAKMP (0:1): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Former State = new State IKE_READY = IKE_I_MM1
1d20h: ISAKMP (0:1): early changes of Main Mode
1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE
1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...
1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1
1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE
1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE
1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...
1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1
1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE
1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE
1d20h: IPSEC (key_engine): request timer shot: count = 1,.
You must also allow the esp Protocol in your ACL.
access-list 101 permit esp any host x.x.x.x (address of the hub)
Hope this helps,
-Nairi
-
Internet through a RA IPSec VPN Tunnel traffic
Armed with an ASA 5505 Security Plus, I configure IPSec VPN for RA the VPN IP address pool is in the 192.168.2.0/28 network.
The Lan is 192.168.1.0/24 with inside interface a.254.
The VPN works great. What I would do is to route all internet through the firewall traffic when users are connected to the VPN. I put this gateway 192.168.1.254 tunnel, but I'm having no luck to get it works.
Any ideas?
Thanks in advance!
You are just going to route internet traffic to the remote vpn client to the ASA and backward on the Internet?
If the above statement is correct, you need not configure the tunnel default gateway.
But you need to configure NAT for the ip pool, so they can go to the internet, as well as the 'same-security-movement' command as follows:
NAT (outside) 1 192.168.2.0 255.255.255.0
permit same-security-traffic intra-interface
In addition, assuming that you have not have split configured tunnel.
-
IPSec VPN between ASAs with same subnet for disaster recovery
Hello
I need some clarification from you guys.
To do disaster EasyVPN tunnels for the Cisco ASA 5505 firewall recovery site. Now, there is only one main site and 3 remote sites.
Dr., must use the same subnet that it is on the main site because virtual machines Vmware will be replicated to DR.
For the DR we use Double-Take software.
What is the best solution for this? I think we could use NAT of Destination on ASAs. Other sites (HQ and remote control) will be directed to only address NAT of the
DR and not real which is the same as on the main site.
So guys, will this work? We are using IPSec VPN? In packet - trace on ASA, I see that the package is the first using a NAT, and then encrypted, so it should work, Yes?
I hope someone can confirm this.
I can confirm that this will work certainly,
for prior type natting see 8.3:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080b37d0b.shtml#diag
for 8.3 and later it is also achievable.
-
Routing access to Internet through an IPSec VPN Tunnel
Hello
I installed a VPN IPSec tunnel for a friend's business. At his desk at home, I installed a Cisco SA520 and at it is remote from the site I have a Cisco RVS4000. The IPSec VPN tunnel works very well. The remote site, it can hit all of its workstations and peripheral. I configured the RVS4000 working in router mode as opposed to the bridge. In the Home Office subnet is 192.168.1.0/24 while the subnet to the remote site is 192.168.2.0/24. The SA520 is configured as Internet gateway for the headquarters to 192.168.1.1. The remote desktop has a gateway 192.168.2.1.
I need to configure the remote site so that all Internet traffic will be routed via the Home Office. I have to make sure that whatever it is plugged into the Ethernet on the RVS4000 port will have its Internet traffic routed through the Internet connection on the SA520. Currently I can ping any device on the headquarters of the remote desktop, but I can't ping anything beyond the gateway (192.168.1.1) in the Home Office.
Any help would be greatly appreciated.
Thank you.
Hi William, the rvs4000 does not support the tunnel or esp transfer wild-card.
-
Cisco ASA 5515 two asa firewall ipsec vpn tunnel is not coming
HelloW everyone.
I configured ipsec vpn tunnel between Singapore and Malaysia with asa firewall.
but the vpn does not come to the top. can someone tell me what can be the root cause?
Here is the configuration of twa asa: (I changed the ip address all the)
Singapore:
See the race
ASA 2.0000 Version 4
!
ASA5515-SSG520M hostname
activate the encrypted password of PVSASRJovmamnVkD
names of
!
interface GigabitEthernet0/0
nameif inside
security-level 100
IP 192.168.15.4 255.255.255.0
!
interface GigabitEthernet0/1
nameif DMZ
security-level 50
IP 192.168.5.3 255.255.255.0
!
interface GigabitEthernet0/2
nameif outside
security-level 0
IP 160.83.172.8 255.255.255.224
<--- more="" ---="">
!
<--- more="" ---="">
interface GigabitEthernet0/3
<--- more="" ---="">
Shutdown
<--- more="" ---="">
No nameif
<--- more="" ---="">
no level of security
<--- more="" ---="">
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
nameif test
security-level 100
IP 192.168.168.219 255.255.255.0
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
connection of the banner ^ C please disconnect if you are unauthorized access ^ C
connection of the banner please disconnect if you are unauthorized access
boot system Disk0: / asa922-4-smp - k8.bin
passive FTP mode
network of the SG object
<--- more="" ---="">
192.168.15.0 subnet 255.255.255.0
network of the MK object
192.168.6.0 subnet 255.255.255.0
service of the TCP_5938 object
Service tcp destination eq 5938
Team Viewer description
service tcp_3306 object
Service tcp destination eq 3306
service tcp_465 object
tcp destination eq 465 service
service tcp_587 object
Service tcp destination eq 587
service tcp_995 object
tcp destination eq 995 service
service of the TCP_9000 object
tcp destination eq 9000 service
network of the Inside_host object
Home 192.168.15.202
service tcp_1111 object
Service tcp destination eq 1111
service tcp_7878 object
Service tcp destination eq 7878
service tcp_5060 object
SIP, service tcp destination eq
<--- more="" ---="">
service tcp_5080 object
Service tcp destination eq 5080
network of the NETWORK_OBJ_192.168.15.0_24 object
192.168.15.0 subnet 255.255.255.0
inside_access_in list extended access allowed object SG ip everything
OUTSIDE_IN list extended access permit tcp any newspaper EQ 9000 Inside_host object
access extensive list ip 192.168.15.0 outside_cryptomap allow 255.255.255.0 object MK
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 30000
debug logging in buffered memory
recording of debug trap
debugging in the history record
asdm of logging of information
host test 192.168.168.231 record
host test 192.168.168.203 record
Within 1500 MTU
MTU 1500 DMZ
Outside 1500 MTU
test MTU 1500
management of MTU 1500
no failover
<--- more="" ---="">
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 7221.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source SG SG static destination MK MK non-proxy-arp-search to itinerary
!
network of the SG object
NAT dynamic interface (indoor, outdoor)
network of the Inside_host object
NAT (inside, outside) interface static 9000 9000 tcp service
inside_access_in access to the interface inside group
Access-group OUTSIDE_IN in interface outside
Route outside 0.0.0.0 0.0.0.0 160.83.172.x 1--->--->--->--->--->--->--->--->--->
Route inside 10.0.1.0 255.255.255.0 192.168.15.199 1
Route inside 10.0.2.0 255.255.255.0 192.168.15.199 1
Route inside 10.0.11.0 255.255.255.0 192.168.15.199 1
Route inside 10.1.0.0 255.255.0.0 192.168.15.199 1
Route inside 10.8.0.0 255.255.0.0 192.168.15.199 1
Route inside 10.104.0.0 255.255.0.0 192.168.15.199 1
Route inside 192.168.8.0 255.255.255.0 192.168.15.199 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
<--- more="" ---="">
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http serverCommunity trap SNMP-server host test 192.168.168.231 *.
No snmp server location
No snmp Server contact
Server enable SNMP traps syslog
Crypto ipsec transform-set ikev1 VPN-TRANSFORM esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
<--- more="" ---="">
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
<--- more="" ---="">
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto CRYPTO - map 2 map corresponds to the address outside_cryptomap
card crypto CRYPTO-map 2 set peer 103.246.3.54
card crypto CRYPTO-map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto CRYPTO-map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
CRYPTO-card interface card crypto outside
trustpool crypto ca policy
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
aes-256 encryption
sha hash
Group 2--->--->--->
life 86400Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
internal GroupPolicy1 group strategy
attributes of Group Policy GroupPolicy1
Ikev1 VPN-tunnel-Protocol
username, password admin eY/fQXw7Ure8Qrz7 encrypted privilege 15
username gmsadmin password HS/VyK0jtJ/PANQT encrypted privilege 15
tunnel-group 143.216.30.7 type ipsec-l2l
tunnel-group 143.216.30.7 General-attributes
Group Policy - by default-GroupPolicy1
<--- more="" ---="">
IPSec-attributes tunnel-group 143.216.30.7
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
Overall description
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
<--- more="" ---="">
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:ccce9a600b491c8db30143590825c01d
: endMalaysia:
:
ASA 2.0000 Version 4
!
hostname ASA5515-SSG5-MK
activate the encrypted password of PVSASRJovmamnVkD
names of
!
interface GigabitEthernet0/0
nameif inside
security-level 100
IP 192.168.6.70 255.255.255.0
!
interface GigabitEthernet0/1
nameif DMZ
security-level 50
IP 192.168.12.2 255.255.255.0
!
interface GigabitEthernet0/2
nameif outside
security-level 0
IP 143.216.30.7 255.255.255.248
<--- more="" ---="">
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
nameif test
security-level 100
IP 192.168.168.218 255.255.255.0
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
<--- more="" ---="">
Interface Port - Channel 1
No nameif
no level of security
IP 1.1.1.1 255.255.255.0
!
boot system Disk0: / asa922-4-smp - k8.bin
passive FTP mode
clock timezone GMT + 8 8
network of the SG object
192.168.15.0 subnet 255.255.255.0
network of the MK object
192.168.6.0 subnet 255.255.255.0
service of the TCP_5938 object
Service tcp destination eq 5938
Team Viewer description
service tcp_3306 object
Service tcp destination eq 3306
service tcp_465 object
tcp destination eq 465 service
service tcp_587 object
Service tcp destination eq 587
service tcp_995 object
tcp destination eq 995 service
service of the TCP_9000 object
<--- more="" ---="">
tcp destination eq 9000 service
network of the Inside_host object
Home 192.168.6.23
service tcp_1111 object
Service tcp destination eq 1111
service tcp_7878 object
Service tcp destination eq 7878
service tcp_5060 object
SIP, service tcp destination eq
service tcp_5080 object
Service tcp destination eq 5080
network of the NETWORK_OBJ_192.168.2.0_24 object
192.168.6.0 subnet 255.255.255.0
inside_access_in list extended access allowed object SG ip everything--->--->--->--->--->
VPN-INTERESTING-TRAFFIC extended access list permit ip object MK SG
OUTSIDE_IN list extended access permit tcp any newspaper EQ 9000 Inside_host object
outside_cryptomap to access extended list ip 192.168.6.0 allow 255.255.255.0 object SG
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 30000
debug logging in buffered memory
recording of debug trap
asdm of logging of information
<--- more="" ---="">
host test 192.168.168.231 record
host test 192.168.168.203 record
Within 1500 MTU
MTU 1500 DMZ
Outside 1500 MTU
test MTU 1500
management of MTU 1500--->
reverse IP check management interface path
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 7221.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source MK MK static destination SG SG route no-proxy-arp-search
NAT (inside, outside) static source NETWORK_OBJ_192.168.2.0_24 NETWORK_OBJ_192.168.2.0_24 static destination SG SG route no-proxy-arp-search
!
network of the MK object
NAT dynamic interface (indoor, outdoor)
network of the Inside_host object
NAT (inside, outside) interface static 9000 9000 tcp service
inside_access_in access to the interface inside group
Access-group OUTSIDE_IN in interface outside
Route outside 0.0.0.0 0.0.0.0 143.216.30.x 1
<--- more="" ---="">
Route inside 10.2.0.0 255.255.0.0 192.168.6.200 1
Route inside 10.6.0.0 255.255.0.0 192.168.6.200 1
Route inside 192.168.254.0 255.255.255.0 192.168.6.200 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
Enable http serverNo snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 VPN-TRANSFORM esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
<--- more="" ---="">
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
<--- more="" ---="">
--->--->--->
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec pmtu aging infinite - the security association
crypto CRYPTO - map 2 map corresponds to the address outside_cryptomap
card crypto CRYPTO-map 2 set peer 160.83.172.8
card crypto CRYPTO-map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
CRYPTO-card interface card crypto outside
trustpool crypto ca policy
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
SSH timeout 60
SSH group dh-Group1-sha1 key exchange
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
internal GroupPolicy1 group strategy
attributes of Group Policy GroupPolicy1
Ikev1 VPN-tunnel-Protocol
username, password admin eY/fQXw7Ure8Qrz7 encrypted privilege 15
username gmsadmin password HS/VyK0jtJ/PANQT encrypted privilege 15
<--- more="" ---="">
tunnel-group MK SG type ipsec-l2l
IPSec-attributes tunnel-group MK-to-SG
IKEv1 pre-shared-key *.
tunnel-group 160.83.172.8 type ipsec-l2l
tunnel-group 160.83.172.8 General-attributes
Group Policy - by default-GroupPolicy1
IPSec-attributes tunnel-group 160.83.172.8
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
<--- more="" ---="">
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: endGood news, that VPN has been implemented!
According to the ping problem, my suggestion is to check, if some type of firewall based on host computers on both sides block ICMP requests.
Anyway, you can still use the capture of packets on the inside of the interfaces of the two ASAs, to check if the ICMP traffic is to reach the ASA.
In addition, you can try to enable ICMP inspection:
Policy-map global_policy
class inspection_defaultinspect the icmp
inspect the icmp error
--->---> -
Hello
I am trying to configure an IPSec VPN tunnel between my company and a remote company for the use of FTP secure.
I used the SDM to configure the tunnel on my router based on the information provided by the society that we are trying to connect to. The other company has provided my debug log when I was testing the connection, but I do not know how to read and what could be the problem. I hope someone here can give me an overview of what prevents the tunnel connection.
Please let me know if you need more information.
Thank you
Peter Haase
Peter,
Good job!
Because the tunnel is up, we must not debugs.
I'm glad that finally it works.
HTH
Sangaré
-
WebVPN and anyconnect on the same interface
Hello!!
We have ASA 5520 firewall running with code.9.1 (2). We already have webvpn running on the firewall and has active users to use it. Now, the client came with a new requirement to configure firewalls on the same anyconnect. We have installed VPN more premium license.
(1) is it possible to enable webvpn and anyconnect on the same interface. If Yes, what are the aspects we must consider to allow them both on the same interface?
(2) how much webvpn and anyconnect vpn licenses should I do with my premium lincense?
Please help on this.
shver attached for reference.
Best regards
Sri
Your peers licenses AnyConnect Premium gives you the right to access SSL VPN without customer and focused on the customer.
Licensing is based on the concurrent users so regardless of the simultaneous dosing will work - as long as the number of connected does not exceed 100.
Your site to site VPN IPsec does not count against this permission, but is rather against "Other peer VPNS" which does not require a separate license and is limited by the capacity of the ASA equipment (750 on your platform).
Maybe you are looking for
-
How to add on the photo library to another
I used to have 3 iPhoto libraries. All of them have been converted into libraries. Now that I'm comfortable with pictures, I would like to combine my 3 libraries of photos into one.
-
Why not Shockwave Flash does not update?
I'm running on Windows Vista business with service pack 2. Firefox (13.0.1) list plugin said upgrading Shockwave Flash. I did, but even if I restart the computer, the plug-in should be updated. Could someone help me? Thank you very much.
-
entry of SolidWorks for Labview
Hello I am trying to make a model in Solidworks and try the relay of LabVIEW to order the engines machining model physically. most of the solidworks related questions here are on the soldworks of LabVIEW control - how can I do the reverse? see you so
-
Programmatically add or remove code from diagram?
Hi, I'm creating a vi that generates a code for a user. Is it all as well as to add or delete code on a block by program diagram?
-
I recently switched my DSL Internet to Comcast Cable with a router. I have the Windows 7 operating system with a Netgear N300 WIRELESS router Cable Modem. There is a computer at home put in place, a Toshiba laptop computer with printer and 2 airpor