2 uplinks the single 10 GB - trouble LACP with management network

Similar Questions

• Second NETWORK card takes over the management network

  I have a lab of dev ESXI 5.5 on a Dell PowerEdge 2950 with a dual port GbE NIC (Broadcom NetXtreme II BCM5708).

  My basic configuration was a port of configured NIC (vmnic0) with a switch (vSwitch0) Standard.  vSwitch0 was a group of Virtual Machine (for VMS) ports and a VMkernel Port (for the management network).  Everything worked well at this point.

  When I try to configure the second NIC (vmnic1) to a different network switch port and different to connect to iSCSI, network range vmnic1 took over the management network even if it does not show as being the management network.  After that, I'm more able to connect or ping the IP of vmnic0.

  When you configure the vmnic1, I added connection Type of VMkernel.  I did not choose to use the port for traffic management group.

  When I look at the console and choose to configure the management network I see only being vmnic0selected network adapter.

  Am I misunderstood the management network configuration?  If not, does anyone have a suggestion on what may be wrong or how I can diagnose?

  Thank you for your comments!

  -Sean

  I think I knew what was going on.

  I had my VMkernel for networking (192.168.2.0/24) in a different subnet to the VMkernel for iscsi link port (192.168.1.0/24).  The problem was due to the existence of a network trace unidirectional from 192.168.1.0/24 to 192.168.2.0/24 (but not in the opposite direction). As stated in the post of the blog below and elsewhere, if there are two VMkernels in networks with a direct route, the esxi host will be simply choose one of the VMkernels to act as the management network (no matter if only one of the VMkernels has active network management).

  I thought my networks did not have a direct route because of the impossibility (192.168.2.0/24) management network to communicate with the network of liaison port iscsi (192.168.1.0/24) but because the 192.168.1.0/24 network may route to 192.168.2.0/24, he made the two viable VMKernels to act as the point of view of the host management networks.

  After that I moved the post iscsi binding to a switch with no network route, my problem has been resolved.

  Re-reading the following is a blog post that helped me to understand my problem.

  http://blogs.VMware.com/kb/2013/02/challenges-with-multiple-VMkernel-ports-in-the-same-subnet.html

  Thanks to those who took the time to review and respond to my problem.

• ESXi 5 managing network not automatically start after reboot, or when the output of the mode standby

  vSphere 5.

  ESXi5.

  HI all 5 ESXi installed on HP BL460c G7. HP C7000 Enclouser system connected to the NAC (switch HP series A5800) via the Module HP FlexFabric 10 Gbs. The server has 6 vmcins:

  (1) management network - 2 NIC (1 GB per nic)

  (2) vMotion Network - 2 NIC (1 GB per nic)

  (3) Vitual Machine networks - 2 NIC (2 GB per nic)

  (4) zFCP - 2 network cards (6 GB per nic)

  After you restart or when the output of the mode standby, the management network starts does not automatically, you need to restart manually from the console directly. Hypervisor ISO downloaded directly from the vmware Download Center and all the recommended HP drivers downloaded and installed from HP Download Center.

  OK, another thing you could try is this change that HP recommended for my situation. The CLI performs: esxcfg-module - s "heap_max = 20971520" be2net

  and reboot. The memory default chunk size is not large enough and will change to this size in the next version of the driver.

  Also, have you tried yet 5.0 U1? There are a lot of bugs in U1.

• How to go back to the single-user music of family ahared

  Help, please!

  I want more have Apple music shared with the family. I want to go back to single user.

  Try this-> manage your membership Apple music on your iPhone, iPad, iPod touch, Mac, or PC - Apple Support

• Can the iPad will be the single monitor to a Mac Mini?

  For the most part, everything we do on the computer can be done with the iPad. However, there are some applications for which we need a computer that is running something other than iOS. What we have is for each family member to have an iPad, that would work for 95% of what we do and then have a Mac Mini that anyone can use for applications that do not work on an iPad. We really don't want children using a MacBook, because they are too fragile, and we do not want a monitor constantly sitting around the House. I saw a software that will transform the iPad into a monitor for the Mac Mini. Can this work as the single monitor? I consider the MacMini sitting quietly somewhere in the House, so that each of us could 'plug in' (either wireless or wired, not sure how it works) to him with an iPad when it takes more computing power. The MacMini would never be used with anything other than an iPad as a monitor. Is this possible? Thank you!

  There are apps like the Team Viewer free (for non-commercial use) and the paid LogMeIn and the GoToMyPC that allows an iPad control/use a computer...

  Do you need a real screen and keyboard initially configure the Mac

• How can I get records events outside of the single folder in Photos?

  I read a response indicating that the old iPhoto 'events' can be moved out of the single folder "in the sidebar. I don't recognize a sidebar on my screen of Photos. How can I get some or all of these events/albums out of this unique folder and on the screen, as well as the other albums? I just upgraded to El Capital and Photos. I really prefer to choose to bring out in the form of records, and to select individual images in the other events to create new albums if they are possible. I also want to get rid of albums smart premade if possible.

  To display the sidebar, choose display in the menu, then see the sidebar.

  You can select all albums under the events folder and drag them to the Albums. That will remove the record albums. Do the same for any other folder that you want to delete records from.

  You cannot delete the default Ablums Smart. You can delete only the albums or smart albums you create.

• Arrow keys serve page upwards or downwards instead of the single line upward or down, can't change it back.

  Keyboard up and down arrows use page up/page down instead of the single line up/down keys. I can't find how to change their return.

  This has happened

  Each time Firefox opened

  is my last installed update

  Maybe you turned Caret browsing. Press F7 and see if this is fixed.
  http://KB.mozillazine.org/accessibility.browsewithcaret

• Trying to create a Section to multiple columns with Sections of the single column before and after

  Is there a way to create a section break that is not default to a new page after I created columns on a page.  I created the columns and under them, I want to return to the normal formatting for the rest of the single page.  See picture attached.

  Any rejection of Pages v5 has a break of presentation which was present in the Pages ' 09 v4.3. This will allow you to transition to several columns and back to single column on the same page. In the v5 Pages, you can insert 3 text boxes and change the 3-column layout in the Middle text box. You use the toolbar item Insert to inject column breaks when you want to start a new list in the next column. I'll show this screenshot below.

  You can fake your layout in Pages v5 using 3 text boxes and setting 3 columns in the Central text area. Better to show the mode of provision for this and in a text box, the column outlines are not displayed. After each column list, you then choose column break the Insert point toolbar menu to move to the next column, add a list, repeat. Each column will expand downwards. Click on the following to enlarge.

  Pages ' 09 v4.3 using layout breaks Pages using 3 text boxes V5.6.1                                                      

    

• Get the Max values and average of the different cycles in the single channel

  Hello

  I'm trying to get the Max values and average of the single channel that has different cycles it contains. I tried to use commands such as Chnclasspeak3 and chnpeakfind, but they were not useful for me. What I need is the Max values and average of the different cycles numbers saved in the data channel.

  Exampld if the string contains 5 numbers of repetitive cycles, then we must find the maximum values and the average of these 5 cycles in the single channel. Attached reference data. This is the .raw file and I have the plugin for it to use in diadem 11.1.

  Kind regards

  X. Ignatius

  Hello, Ignatius,.

  Sorry, it took some time to provide a replacement based on the script for the function. Please take a look at the attached script. I changed the script to use my function if the tiara-version is less than 12. My script function is not as fast and more stable than the implementation of tiara, but for now, it does the job

  Andreas

• scanning multiple pages to the single PDF using HP ENVY 4500

  The guide says scan of the computer (as opposed to scanning from printer).  I do that and still can't scan multiple pages into a single PDF file.  Is it still possible?

  Hi griff0530,

  I understand that you want to scan multipage documents into a single .pdf file using your HP Envy 4500, yes it is quite possible.  When you use the HP software on your computer, follow the steps below:

  1. loading the document.

  2. click on scan . An overview of the analysis is displayed (by default).

  Important : the Preview Scan function must be enabled for scan multiple pages into one file documents. Additional pages from the original are added for the single file in the Scan preview window.

  3. in the scan preview is displayed, do one of the following actions:

  Click the sign Plus () on the left side of the window to scan additional pages. If you do not use an ADF, you must load the next page of the document on the glass of the scanner to add to each additional page.

  4. click on Save to capture the scanned file, but leave open the HP Scan.

  5. click on done to capture the scanned file and close HP Scan.

  I found this great information here: how Scan: Windows 7

  If you are using any other operating system, it's ok the same steps apply. I hope that's what need you!

  Thank you

• Windows XP loses two monitor settings and returns to the single monitor after to be identified only by the windows... No reboot is

  To begin with, I am the HelpDesk of the company and our users are running Windows 7, Vista and XP. The problem will occur randomly on most XP and Vista systems.

  I'm beginning to believe that it is a computer problem to the extent of the material or something of this nature.

  For now, I swapped the computer and now the question is not fooled by the user.

  But in general I wanted to know why this happens. They will be blocked (not a stop) their computer to take a lunch break and when they return to log in order to return to work. They work on two monitors and for some reason, as the settings go back to the single screen...

  Why this keep happening? Help, please?

  Either way, I don't think it's a driver problem... Because I just run images on hard drives of all application users run and the problem occurs randomly.

  Thanks in advance for your response...

  Adolfo

  Hello

  The Microsoft Answers community focuses on the context of use. Please join the professional community of COMPUTING in the TechNet forum below

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

• How to solve the single FAX problems

  After HP8600 is installed, what impression the network always goes to FAX instead of the printer. How to solve the single FAX problems

  Hello jim3258and welcome to the Forums of HP, I hope you enjoy your experience!

  I see that you have problems printing and fax.  I'd love to try to help you, but I need some information first. I'm a link some HP Support documents below that will show you how to find the number for your product. In addition, please indicate what operating system you are using. In addition, if you are using Windows, please indicate if your operating system is 32-bit or 64-bit. With this information and the product number we provide you with accurate information.

  How can I find my model number or product number?
  Mac OS X: how to find which Mac OS X Version is on my computer?
  Operating system Windows am I running?
  Is the Version of Windows on my computer 32-bit or 64-bit?

  Please let me know what you find.  Thanks for posting on the HP Forums!

• Windows 7 scheduled for the single folder backup

  Hello

  I have windows 7 laptop. In my laptop take a single folder to another regular in backup.how location is saved in a single folder as a scheduled backup. I don't want a whole disc as these backup (disk C or D or E). I want only the single file. Send me answer as soon as possible.
  Thank you
  Audi

  Open the backup and restore , and then run the wizard. If you go the the computer > C: path of reader you can select an individual file or multiple of the folders to back up. See the screen shot...

  http://CID-25ab668da65c8fbe.photos.live.com/self.aspx/Windows%20images/BackupSelectFolders.PNG

• Create the single '. " ALX "file of multiples. ALX file?

  Hi guys,.

  Is it possible to create the single '. " ALX "file of multiples. ALX file?

  If possible, please let me know.

  Thanks in advance,

  Yes, it's easy to do.

  Just add several files to the

  Element.

• Channel Port LACP with VMWare ESXi IP hash Message: % SW_MATM-4-MACFLAP_NOTIF: < MAC > host in the vlan 1 is flapping between port

  Hello

  Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750.  I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-

  src-dst-ip port-channel load-balance

  Interface Port-channel15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  !

  interface GigabitEthernet1/0/15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/16

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/17

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/18

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/19

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/20

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  Currently I see many MAC beat in the log of the switch.  From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP.  I'm worried about the impact this might have on the CPU / switch.

  August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17

  August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20

  August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  Is it by design, if so can I disable the message?  If this isn't the case, please can you advise where I can check/change the configuration?

  Thank you

  Peter

  It is really gud who... .you mentioned your solution here.

  Can you please mark this question as answered, thatâ so it can help the other guys.

  Concerning

  Please rate if this can help.