2720 XPS does not start after replacing mSATA SSD 32 GB

Similar Questions

• Satellite Pro S300-120 does not start after replacing the CMOS battery

  Hello

  My friends laptop - a S300-120 - was having a few problems.

  I replaced some parts about this before, including a screen crack with no problems.

  However, he began to refuse to start saying "out of battery CMOS, Press F1 to enter setup". Of course you would have to do this, set the date and time, except & restart only to get the same message. We have replaced the CMOS battery with a with the same serial number and now the laptop will not boot.

  It does one of two things.

  It is one) seems to turn, turn to the top disk & CD player, cooling fan is 100%, then flashes the POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.

  Or (b) turns on, turntable, does not turn up to cooling fan, POWER ON witness remains stable, no response from the keyboard or LCD.

  I re-assembled the laptop several times & can not find all the missing fittings or obvious signs of damage.

  The only thing I can think is that the motherboard has been damaged - somehow find replacements is delicate.

  Any ideas?

  Hello

  (> It is a) appears to turn on, turn the disk & CD player, cooling fan goes to 100% and then flashes him

  POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.
  Usually, if the voltage in abnormal feeding malfunctions when IN DC will be blinking orange.

  In my opinion, it looks like a problem with the motherboard :(
  Eventually, you will need to replace the mobo ;(

• Does not start after replacing the cmos battery

  HP m8430f, Vista Home Premium.  Worked very well but sometimes had to restart using "pulsed" F10 (5 seconds) then wait 5 seconds, and then F5, then ENTER, F10, then ENTER.

  I suspected the CMOS battery, so I removed it.  He tested "fair."  Got a new CR2032.  He attached the test counter, so it's okay  "I WAITED ALL NIGHT BEFORE REPLACING.  But the computer does not restart.  I went through the steps above and still no luck.  What to do next?  Thank you, Joe

  FIXED!  I removed the battery (I had to remove the sound card to get in the first place to the battery).  I waved it around a little when you reinstall.  Now it's working.  What I've done, I have no idea, but it works now.  Sorry for the post, but I was desperate.  Joe

• Windows10 car does not start after cloning of SSD (mid-2010)

  Hi all.

  In my mid-2010 mac pro, I have a windows disc 10 (upgraded to 8.1 windows) in the Bay 3. I want to update to SSDS. So, I bought one, I cloned the drive with winclone app pro (v.5.4) but the new drive is not bootable. When I choose to boot from it, it stops at a white (command line - like) screen BACK with a flashing dash.

  Any suggestions?

  The problem was to limitations of El Capitan. The operating system does not other applications to write to the MBR (...) od disks. If the new disk is unable to be started.

  I installed Yosemity in another disc and clone the HDD to the ssd from there.

  There was another solution to disable "csrutil" of Terminal recovery, but another problem I had, doesn't have me let go to recovery mode (frequent readers of fusion).

• EliteBook 8640p does not start after replacing hard drive with a 128 GB crucial disc M4

  Hi all

  This morning I was not in box a new Elitebook 8640 p and instantly replaced the hard drive with a new 128 GB crucial disc M4.

  Machine installation installation clean Windows, restarted etc. I then installed the drivers, restarted etc. Have a windows index score and I was immediately impressed by the 7.9, but...

  The laptop won't start. Right after that the first portable screens it just stops at a black screen where it should show the logo "windows". I put the original hard drive in and the machine starts very well and I put the M4 in my office and it begins to start.

  It seems so the reader is fine and the laptop is fine, but the whole... Nope.

  Any suggestions?  (I want to send them both back after spending this money a lot of things should work like clockwork)

  Solution: It seems that Crucial screwed up again

  http://Forum.crucial.com/T5/solid-state-drives-SSD/problem-with-boot-on-SSD-crucial-M4-256Go-on-Asus-N73SV/TD-p/47678/page/3

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• Does not start after the reload of the operating system

  OK, this is my story of boredom.  I have a Lenovo T61 Type 6463-5BU, S/N L3-xxxxx.  The hard drive died a few weeks ago, and since then, I have received a replacement drive under warranty, that is the exact same drive type.  We had a backup image of the old system under Norton Ghost and managed to get the image to the new disk once it has been installed.  To do this, we used a utility called OS
  'BartPC '.

  Since then, I did pretty much everything I can think of to get the system to boot, including playing with the BIOS settings, setting the drive to 'boot' and 'active' with the help of a number of public services, including the good old "diskpart" and many others.  The reader will just not start.  A few times I could read the disc using Bart in command prompt mode, but I never managed to boot from it.

  The laptop has a finger print reader, but I was told several times that this has nothing to do with the problem.  So... before I cut off the finger of a person and drag in the player... What am I doing wrong here?

  Note of the moderator; s/n, under the direction of protection own members

  AGoodSolutionideas can save I hope as your image.

  For later use, take a look at this document from Lenovo on the use of Ghost; Partition does not start after being restored with Norton Ghost - NetVista / ThinkCentre / ThinkPad...

  I know it says 'prior to 2004 systems', but it is still topical.

• Pavilion dm3-2020eo does not start after change of RAM

  As the topic says my computer does not start after a change of the RAM.

  I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

  According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

  Can someone help me?

  Thank you
  Leo

  Here's the key:

  We're working on two sockets and one does not at all.

  You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

• Pavilion dm4-1265dx does not start after Windows 7 logo

  My laptop does not start after the "Starting Windows" screen when I try to boot the operating system normally. When I try to run the repair mode from the start nothing happens... I get a blue background image and the pointer of the arrow, but no icons or windows appear.

  I tried the system diagnostic mode by pressing ESC when turning the laptop on and the hard drive test fails every time, showing the following results:

  Test Drive: 1
  INTELLIGENT control: passed
  DST short: failure

  Failure ID: 64RG79-5AP62V-XD6U2K-60RN03
  Product ID: XZ298UA #ABA

  Hard drive 1

  --------------------------------------------------------

  Test drive: FAILURE

  How should I proceed? The laptop is still under warranty, but it was purchased in the United States, and I now live in the Brazil.

  Hello

  You will need to replace the hard drive.

  HP should send you a new drive for free, but in your case is a little complicated as you mentioned it already. Please contact HP tell them about this situation. How to do?
  Click on the link below and choose your country:
  Contact HP worldwide

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• The browser does not start after you have turned off and turned on the computer

  The browser does not start after you have turned off and turned on the computer. I tried to remove the program entirely (as well as personal preferences), to create a new account, install a different browser versions. All this has not helped. (I have Windows 7). Help, please! Every day I have to reinstall Firefox!

  Hello Nastena, try a clean reinstall, some Firefox issues can be resolved by performing a clean reinstall. This means that you Remove Firefox program files and then reinstall Firefox. Please follow these steps:

  Note: You can print these steps or consult them in another browser.

  1. Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
  2. Once the download is complete, close all Firefox Windows (click on quit in the file menu or Firefox).
  3. Remove the Firefox installation folder, which is located in one of these locations, by default:
     • Windows:
       • C:\Program Files\Mozilla Firefox
       • C:\Program Files (x 86) \Mozilla Firefox
     • Mac: Delete Firefox in the Applications folder.
     • Linux: If you have installed Firefox with the distribution-based package manager, you must use the same way to uninstall: see Install Firefox on Linux. If you have downloaded and installed the binary package from the Firefox download page, simply remove the folder firefox in your home directory.
  4. Now, go ahead and reinstall Firefox:
     1. Double-click on the downloaded Setup file and go through the steps in the installation wizard.
     2. Once the wizard is completed, click to open Firefox directly after clicking the Finish button.

  Please report back to see if this helped you!

  • Also check if your antivirus or other access security software (firewall, antispyware etc.) blocks firefox.

  Thank you

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.