5K retina Mac Shutdown sudden problem

Similar Questions

• Several weird, sudden problems in Multisim, Ultiboard interface

  I have several sudden problems that arose when trying to review a design that changed, I worked on a couple of months ago.

  Multisim 10.0.343 strangeness:

  1. by clicking on a Multisim, Multisim project file opening, but the project file does not open. By clicking on 'Open' Multisim has the same effect. If I manually open the circuit, the entire project opens as well.

  2. I can no longer double click on a component and change the footprint; the button "Replace" is also disabled. I can always change the footpring of spreadsheet view.

  3. the icons for the placement of the pieces have changed to blue squares with black patterns (from grey buttons with color schemes).

  4. multiple drop-down menus in the top bar disappeared ('reports' is the only one that comes to mind, but the list is significantly smaller).

  5 ' transfer' menu has only one option - transfer to Ultiboard 10. There is no rear annotation or annotation.

  6. Select 'Transfer to Ultiboard 10' open the splash screen for Ultiboard and gives me the option to choose a file name, but nothing opens after that. There is no blocking or error - just nothing opens.

  On a separate note: the last time I did a major revision of this circuit, I changed a lot of net names. NET names, however, has not changed; for example, I renamed a node 'Gsyn' to 'Gs '. The 'Gs' appears in the worksheet view and the properties of the net, but 'Gsyn' always appears on the diagram and is not suppressible.

  Ultiboard 10.0.1 strangeness:

  1. the renumbering of the components in the design menu translates into a sort of re-assignment pad, causing many connection errors.

  2. same mistake earlier in the forums without response: after before annotate Multisim earlier, the list of included changes 'edit the existing component XX' for each component in the design, regardless of whether the component has been modified or not.

  3 when you place a trace which is too close to other tracks by my rules of design, I sometimes get advice 'cannot create (1) drop of water ". The program is then suspended until I click on something other than Ultiboard (show Desktop, switch to another program, etc.) When I go back to Ultiboard, the program of the United-grip Nations - but then it works super slowly, no display of updates for a few seconds and zoom in and out in pieces. I have to close and reopen the file to continue working.

  Any help would be appreciated - I'm on a deadline, and both programs are more or less completely unusable now.

  Hello

  Please take a look at the following knowledge base to resolve the issue of Multisim:

  Making gray out

  Reset the User Interface

  It is difficult to tell what is the problem with the annotation to the front without looking at the Multisim and Ultiboard files. If you can, please create a service request to ni.com/ask and send us the files.

  1. When you annotate forward, the PIN does not change is the imprint that has changed.  If the footprint currently on the design before annotate before is different from the PIN that is in your library, when you transfer annotate, Ultiboard will update the fingerprint with that of your database, this may explain what you see.

  2. you need to compare the fingerprint in your schema with what is on the printed circuit, if the fingerprint matches, Ultiboard will get what is on the circuit board to the wide and place a new there.  Take a look at the knowledge base of Unplaced Pieces after annotate with impatience , he can explain what you see.

  3 turn off the tear drop feature (Options > preferences > PCB design) and carry your board without this feature, once you completed the Board of Directors of routing, add the tear drops (design > add teardrops).

• I can't send email Outlook Express (sudden problem). It is a new and sudden issue. Error number: 0x800CCC67

  Original title: I can't send email Outlook Express (sudden problem). It is a new and sudden issue.

  I use Outlook Express 6 and make this message. An unknown error has occurred. "Account: 'XTRA', server: 'smtp.xtra.co.nz', Protocol: SMTP, server response: ' 421 mta01.xtra.co.nz connection refused [222.155.136.138] ', Port: 25, secure (SSL): no, Server error: 421, error number: 0x800CCC67.

  Continues to receive e-mails.

  Hello

  Have you made changes on the computer before this problem?

  The following article might be useful.

  Troubleshooting error messages that you receive when you try to send and receive e-mail in Outlook and Outlook Express
  http://support.Microsoft.com/kb/813514

• Win 10 typewriter fileshare accessed by XP and MAC machines without problem.

  Win 10 typewriter fileshare accessed by XP and MAC machines without problem.

  Try to connect to a Win 7 machine, but he insists on the fact that the connection doesn't have access to the share.

  The login and the password are valid. Sharing and security is open to all. All machines are in the same workgroup.

  The machine win 7 can see another machine on the net and the Win10 machine can see actions in the Win 7 box.

  It is just the win7-online win10 that is the problem.

  Hello

  Thank you for visiting Microsoft Community.

  I suggest you to post your query on our Forums TechNet social as this question should be better there.

  Please refer to the reference to the link below to send your request:

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=w7itpronetworking

  Hope this information helps.

  Sincerely,

  Ankit Rajput

• I bought two Lightroom... One for Mac and one for Windows but Mac gives me problem... it happened in judgment and now it won't open upwards - and how that I associate my Mac purchase at a monthly payment as my Windows plan? Its a plan photograph b

  I bought two Lightroom... One for Mac and one for Windows but Mac gives me problem... it happened in judgment and now it won't open upwards - and how that I associate my Mac purchase at a monthly payment as my Windows plan? Its a plan of photography by Adobe (including lightroom and photoshop)

  Hi Robertc70810949,

  It is a digression of your technical question, but you haven't purchased two separate subscriptions for creative cloud? You are probably aware of this, but just in case you're not, a single Plan of creative photography cloud allows installation and activation on two computers. These computers can be two Macs, two windows, or one of each. See Adobe Creative Cloud FAQ for more information. Of course, you can have another reason to buy multiple subscriptions, but I wanted to clarify in case you can save yourself a little money.

  Kind regards

  Del

• Sudden problems with Adobe on Mac

  I have a Mac I-.  Used for years with Adobe to read and print PDF files.

  Yesterday, all of the sudden many questions.  Could not print some documents.  Other documents looked very strange, with black background and green type.

  Today, the message is that Adobe Reader cannot be opened.  As a result, cannot view or print PDF files.

  What is the problem?

  Hi jattogox96140952,

  Please provide the exact point of the software & OS installed on your system. Also check if it is there any update available for the software after crossing "" help > check updates "»

  Follow this thread to reset the Acrobat preferences:- How to reset preference settings in format Acrobat.

  Would like to know is what is happening with some or all of the documents.

  For printing issues, please refer to this article:- print troubleshoot PDF in Adobe Acrobat and Reader

  If the problem persists, then would you please check with the account of another user with Admin rights to reproduce the problem.

  Kind regards

  Christian

• retina Mac suddenly begin to become very hot. before hot only

  I bought my laptop around October 2014 and a month ago not hot start you can hear the fans, before I have never I have this problem it will only warm up and will never heard the fan even when you watch videos on HD thanks for any info on this.

  You can try a SMC reset and test to see if the problem still occurs. Do a Google search for resetting the SMC on a Mac.

  Videos may cause the fans to run the CPU or GPU is currently imposed, causing excessive heat.

• Sierra Mac OS startup problems

  Since the upgrade to Mac OS Sierra on my MacBook Pro (retina, 15 inches, mi 2014) I had starting problems. Before that my Mac should restart within seconds (usually less than 10-15 seconds); Since the upgrade, it took more than 4 minutes when I click on restart when I can log in. And I only actually get to the login screen about 50% of the time. The other 50% of the time, it just hangs and doesn't restart at all (black white screen, keyboard enlightened and illuminated Apple logo on the case). In these situations, I have to force power off (holding down the power button, then press power to restart). This problem occurs regardless of whether or not I am logged on my account or simply by using the "Restart" button on the login screen. Any help or ways to shoot bad, it would be appreciated.

  Try to start in safe mode (hold down the SHIFT key when starting). Reset.

  If the problem persists, download Etrecheck from https://etrecheck.com/, run it and paste the results here.

• ORA-12560: TNS:protocol adapter error. Virtual MACHINE works on old MBP and Win7 but not on new MBP [mid 2015 retina], speed or network problem?

  We strive to use our VM on the new retina MBP (mid-2015) with MacOS X 10.11 (El Capitan) but we had a problem starting from Oracle. If we first converted our ESX VM but once on the Mac laptop Oracle (v12.1.0.1.0 on WIN2012R2) does not open the database, error;

  ORA-12560: TNS:protocol adapter error

  Does not change us any setting on the virtual machine itself so services work fine. Network has set the IP with host only. Tried with Fusion 7.1 & Fusion 8.0.2 new Mac with nothing doesn't. Also with the different versions of the VM tools. Tried to remove the NIC in Fusion and recreate, don't sucses.

  Funny enough the same virtual machine starts fine on PC (workstation 10.3.0 & Win7), MBP beginning 2011 (Fusion 7 & Mac 10.10) or ESX itself for Oracle opens the database!

  That's why we think in the direction of the new MBP specific? speed or network issue? Ring the bells?

  
  

  Help appreciated!

  Bottom line, this is a problem of Oracle who dislikes the MBP on a virtual machine.

  for reference;

  Virtual MACHINE works very well on all platforms, but not on the latest MacBook Pro (retina, 15 inch, mid-2015). So, when you try to use sqlplus you might get the error that there is no such thing as SID. Earphone works very well, but the DB process does not record with earphone or work correctly also. But the process is running and a SID tnsping returns an OK. This isn't a problem of configuration Oracle as the VM and DB works well from the moment where you run the virtual machine on a PC or an old MBP. Either way, Virtualbox has the same problem so not a problem of Fusion.

  I will record a deal with Oracle but I doubt that it is corrected.

• SpeedGrade CC 2014.2 build 8.2x51 reading smoothing / jerky 4K with GPU R9 295 x 2 - it uses only 2 GB of RAM (8.1 Windows 64-bit), Mac OS - same problem

  Hello, guys

  I have following configuration:

  I7-5960 x 4.3 GHz

  32 GB DDR4 RAM

  ATI 295 x 2 8 GB (Gpusniffer.exe watch 3072 MB on each unit of Hawaii)

  Samsung XP941 Ultra M.2 (> 1000 Mb/s)

  Some 850 Pro SSD for H.264 4 k source

  Latest version of Speedgrade CC 16/02/2015 (DUAL MONITOR SETUP - 2560 x 1440 for Interface and 4096 x 2160 for previewing)

  I work with a lot of short 10-15 seconds 4 K 4096 x 2160 24 fps H.264 clips of Panasonic GH4. Import their first CC as some stabilization warp, cut them, save the project and opened in Speedgrade CC all are fantastic smooth in first CC.

  Speedgrade - a simple color - exhibition, some keyframes and simple scoring correction for certain substances. I use the GPU acceleration for sure have lots of 4096 x 2160 4K 24 fps. But it is not flexible and smooth after that a correction is applied. Everything is jerky and freezes the first seconds, when I press 'PLAY'. I used resources, the Manager monitor tasks (Winodws 8.1 64-bit) and Afterburner. And there's what I discovered:

  • Afterburner shows the use of mono-GPU (as we know it for playback only 1 GPU used) the same amount as in first. SpeedGrade CC use 2, 5 GB of VRAM. Also, if I use one zero effect - accelerating gpu, like "transform", for example, imported first, I get "not enough GPU resources" message in Speedgrade. Afterburner shows, CC Speedgrade tried to use more, and then Max 3GB available VRAM during that time. So I turn off these effects, before you open a project in Speedgrade.
  • CPU is low (15%) use, perhaps a little lower, then in the first CC
  • Disc - 3-10%, H.264 is weak on this subject
  • RAM! -is the problem. I have been authorized to use the 29 GB of RAM for Adobe apps. Speedgrade CC use no more then 2-3 GB according to the the Task Manager (for most 2 GB) and 8.1 Windows resource monitor 64-bit Pro. After I finished with the color correction, a project open in first DC, work with lumteri on smooth and! First CC use 9 to 10 GB of RAM to play the same music video in full resolution smoothly!

  
  

  I already reinstalled everything, including drivers for the GPU, 8.1 for Windows and Adobe CC even result.

  MacBook Pro 15 retina end 2013 with i7-4960HQ/16 GB of RAM/Geforce 750 m UPDATE!

  Under Mac Os Yosemite 10.10.2 - same situation here. First CC use 5 GB (of 11 GB of available) 4096 x 2160 Prores 422 HQ and is usable, smooth with a few drops of frame.

  SpeedGrade CC uses 2.5 GB RAM of 4096 x 2160 and it is impossible to use plenty of 4096 x 2160. Only 1/2 resolution of overview is smooth and usable on the screen of the laptop. 4096 x 2160 externally connected through Thunderbolt monitor, it's a lot rougher, I think it's hard for 750 m with 2 GB of VRAM.

  UPDATE! Previous version (CC 2014) of first CC and CC Speedgrade Windows 8.1 64-bit - even situation.

  
  

  What do you think?

  
  

  My opinion - Speedgrade CC is not optimized for 4K resolution. First CC is good for 4K.

  BTW, for more information, latest AMD catalyst driver 14.12 omega has a problem with my R9 295 x 2 and engine reading Mercury (MPE) OpenCL - just black with sound screen, when I turn on the GPU acceleration. So I use the previous version of 14.9. With 14.12 GPUsniffer.exe found a device with 4 GB of VRAM GPU and a GPU with 3 GB of VRAM (normally obligatorily 3 + 3 GB 295 x 2 Dual GPU radeon chip).

  Yes

  So, finally, Speedgrade CC works 95% smooth time with 4096 * 2160 H.264. But it was necessary to turn off all effects in first Pro CC. Nothing new. I found a few discussions on this fact, but after that I spent some time with experiences.

  Stabilizer Warp even alone is enough to make Speedgrade CC really agitated. 'Transform' effect simply blocks Speedgrade CC with "GPU resources.

  Each effect uses some VRAM (for Warp stabilizer 200-300 MB). After you have disabled all effects had load VRAM under/near 2 GB for the little clip 4096 * 2160.

  First CC flies simply with unique x 290 or 295 x 2 (which is the only x 290 during playback). Even 3GB VRAM available software Adobe CC.

  PS Macbook Pro retina 15 "with Geforce 750 M 2 GB VRAM would work smoothly with Prores to half a preview/playback resolution - 2048 * 1080. CC CC SpeedGrade or Premiere Pro with 1/2.

• ID CS5.5 Mac - transparency printing problems custom size 13 x 21

  I try to print a screen printing positive transparency. The document is 13 x 21. I have a roll of 13 extended transparency which I cut a 21 "piece. I print on an EPSON 1400.

  I can not get the output to this szie file. It cuts the image within 8.5 x 11 limit each time.

  I have:

  -set a custom size in the print dialog box

  -Click on Page Setup in the print dialog box and set the custom size here, ignoring the warning to the subject it is not not printing ID dialog box

  -l' Preview in the dialog box will look perfectly oriented to the right size in the small tile

  -J' have tried everything I can think of to try to get in sync and correct output formats

  -I went to the PDF to try, fail again

  Is there someone who can help with some step by step to a process that works?

  Adobe ID CS5.5, EPSON Stylus Photo 1400, Mac Lion 10.7.5

  Only, I can't understand how this could be so difficult and little intuitive. Any idea would be freaking wonderul.

  Wow! Sudden incidental finding on this incredibly frustrating issue.

  I had found information that the EPSON 1400 should be able to print 44 "long output by default. I was looking specifically for one to find people who had printed large and panoramic images and came across a photography website of the United Kingdom where a person mentioned that he had written a software that would allow this printer print beyond 44 ". That sounded a lot.

  BUT, the last post on the thread of a guy says how he was able to print up to 44 '' for an EPSON 1400 with ease. The solution, said, was that the WIDTH of the print in the page layout area must be LOWER at 13 ". Why? No explanation.

  So I reset my size custom at 12.5x21 inches and BAM! First attempt to InDesign printed successfully. I can work with the margin.

  Anyway, in the case that everyone runs into this problem, it works. Here is a link to the post of 2009 that mentions this as info about printing more than 44 ".

  This one is solved.

• Mac Pro start problem

  I have a Mac Pro Tower, that will not start the first time I press the power button, the machine "lights up" in a way that the light in front comes on and I hear a click, however the fans and readers do not engage and the screen is blank. I am then forced to hold down the power button until it stops and hit the power key once again, and each time on the second time it starts. Now I use this equal parts of Mac on the Mac partition and equal parts as a PC, this problem appears when I start in two, but I put in this detail to explain another thing, I have a PC graphics card in the computer. I have all his own CUDA Driver Version that allows me to do it on the mac, but it might have something to do with it. Even if the problem persists when I have my Mac AFI graphics card in the computer as well. I also want to add some other details, nor the mac from the PC partition can go in "standby mode" or the computer goes back to be a brick with just the front light on. (Sometimes the LED keyboard works, and sometimes is not after the mode 'sleep'). In addition, if I restart the computer, it starts well the first time, as well as when I move from mac to PC partition. I tried to do resets of LANDAU and SMC and that has not worked, someone at - it ideas?

  Thanks guys for any input you may have.

  The next time that you touch inside, try to carefully remove the 3 v button cell half hidden behind the graphics card and check the required 3 Volts. If less, a new is needed. You can also use CR2032, which is used for the remote control-door garage and car-door-key original is BR2032.

• Power Mac Pro 2010 problems

  So I just bought a Mac Pro 2010 and it ran fine for a day or two and then I noticed that when he falls asleep the light never blinks and turn even a problem.

  If the unit is off, when I first press the button there is a click but the led stays off and nothing happens. I have to hold down the power button until there is another click. When I press the button once again, there is a click and the power of fans on and the machine finally starts. Although the chime time seems very long.

  However, when he goes to sleep, the monitor turns off, I can hear the fans turns off but never flashes as it should the. Subsequently, the computer cannot be awakened from his sleep. This happens if the timer is active, I press the power button or choose to sleep in the menu. I have to hold the power button to turn it off completely, then start it again. Also, when I press the power button to restart the same as above occurs.

  I ran Onyx to flush all caches that I left my SSD (OWC E2) my Mac Pro 2008. I also reset the SMC and the LANDAU and also ran the Apple Hardware test. Nothing has helped and no errors not found in one of these trials. I tried simply have a HARD classic in this drive and removed all my cards accessories but that does not make a difference. Even when I start windows via boot camp the same problem occurs with sleep.

  Any suggestions?

  I had a similar with a 2010 6 core Mac Pro problem except that the Mac I never sleep, so sleep was not involved. An Apple Store Genius diagnosed as a button battery failure and, eventually, the PS. I asked that the two be replaced since the support for that Mac ends. It's worked OK since then and at Pick-up, engineering was agreed that, while the battery needs replacement, the real problem was the PS.

  Until the repair, one of the things that helped aims to let the Mac disconnected from the AC line for about an hour. Immediately after it by plugging in, he would sometimes start and then work.

• Power Mac G5 power problems...

  Hello, on a quest to find a G5 computer, I found an early 2005 Power Mac G5 (2x2.7GHz). The first time I plugged it in and turned on, it works beautifully. The second time, I pressed the power button and heard a loud noise from the power supply. I replaced and this is what is happening now:

  When I plug the power cable in, there is a small clicking noise about a second after plugging in, and the power led on the front of the machine flashes for the click. However, it does not at all depend on when I press the power button. When I unplug the cable, it makes the same noise about a second after I unplug the unit. I see a pale glow of the light output after unplugging it.

  Anyone have any suggestions to solve this problem? It is part of a collection, that's why I want to do operational.

  There may be defective capacitors or other power supply problems, including

  overheating in the dust inside the power supply or air channels. And

  If the device is cooled by liquid, other things may be involved.

  Since all the PowerMac G5 power supplies are considered to be custom,.

  to get a good replacement is a way hoped to improve the situation.

  Unlikely as is, actually an inexpensive job.

  Have you tried a SMC power management unit reset? Or reset PRAM?

  • How to reset the SMU on a Power Mac G5 (late 2004) or Power Mac G5 (late 2005) - Apple is supported

  To reset NVRAM (PRAM) see:

  • How to reset the NVRAM on your Mac - Apple Support

  Several links appear in the result of this research; some look promising:

  https://DuckDuckGo.com/?q=Troubleshooting + G5 + PowerMac + power + supplies& t = ffsb & AI = web

  I read about the noise, the PowerMac G5 can do when some power components

  fails; Troubleshooting is involved. Somewhere I had a link to a source for official PDF
  REPAIR, download for offline use. -I do not see if I can locate the item...

  Apple Power Mac G5 (early 2005) manual .pdf

  Apple Power Mac G5 (late 2005) manual .pdf

  Apple Power Mac manual G5.pdf

  Good luck!

• HPlaser 1102w: HP Laser 1102w with Mac wifi connection problems

  Right. Hello. Basically, I've had this problem before and someone else fixed, now he has done it again and I really need someone to walk thorugh some steps. Forgive me if it's something really easy, but I'm not a tech person.

  The Maverics, wireless printer Mac was finally up and running, everything was fine.

  Owner changed the router on a better and faster. Yay!

  Printer will connect is more to the Mac. Boo!

  If printer will work when plugged into my computer, but is no longer trying to get wifi.

  I am a PhD student, I really need a printer to work... not to mention, I have three classes to teach next week and may not print all what I need for the class without sitting on the floor, which is fine for some, but it would be much easier if I get this sorted wifi thing and know what to do for the next time this happens.

  Tried to go through the open printer settings of utility, utility will not open. I'm pretty sure that this is where I need to change the wifi info so it can recognize the connection, but cannot understand why it won't work. (Please correct me if I'm wrong!)

  So basically, I need someon to walk me through how to get this recognized for my wifi.

  I know that others have understood a work-around on it using the PC of someone else. This is not really an option.

  Anyone can guide me please you through what to do here, how to get this bloody printer to recognize the new wifi Info? Any help would be appreciated to greately. When this printer is working, it's great. But when the slightest thing goes wrong...

  Thanks in advance. Screenshots and Cape ' do DummySpeak would go a long way with me. I am a student in art, tech, not so much.

  Thank you!!

  Hello @maddyjames,

  Thank you for showing your interest in the HP Forums! I see that you want to configure the printer on the new network. I would like to help.

  Restoration of first default printer.

  Turn the printer off, press and hold the wireless button and cancel (x button) while turning the printer on and do not release both buttons until the printer stops making the noise.

  Print a configuration page to make sure that the old network settings are disabled: print a Configuration or report Page.

  Make sure that Safari is set as default browser. (sometimes the SAP will not open if it is not set by default)

  Open Safari, at the top, select the Safari menu, select Preferences, general, as a default value.

  Remove the printer in printers and Scanners. Plug the USB cable from the printer to the Mac, and add the printer again. Make sure that it shows just the name of the printer. LaserJet P1102w. You may need to run the Apple updates.

  Here's a Youtube video of the Laserjet P1102w on Maverick wireless installation.

  LaserJet P1102w.

  You can follow the steps rather than watch the video if you want.

  Then go to the Apple, system preferences, printers and Scanners.

  Highlight the Laserjet on the left side of the window.

  Then click Open Print Queue, click settings, click utility, click open printer utility, then click the button HTML Config.

  The integrated for the printer Web server opens.

  Click on the network tab, select Wireless on the left side.

  Fill in the information for your network. Make sure that the infrastructure is selected. Status: Make sure that you select enabled.

  Apply the settings.

  Then go back to the Apple preferences system, printers, and Scanners and click the + to add the Hello Laserjet Printer. (may take a few minutes to appear)

  Remove the USB printer in the list of printers and Scanners window.

  Disconnect the USB cable and try and print.

  I would like to know if these measures worked for you. If they did, it's great! Give us some reinforcements by clicking on the solution and laurels, buttons that help and others see that we have the answers! Good luck!