7 HP flow display problem - odd of scratches on screen

Similar Questions

• Calibrate display problems after you run the screen.

  I have a bad problem after running a screen calibrate a Spyder 3 Pro.  I've done this before and no problem, but this time, something went AWOL.  Now I have serious problems with the screen areas header and the context in which the Dock are black?

  The icon screen titles are also black text and it is impossible to see what emails are present because it is also black.

  My screen is a NEC PA272 and I tried to reset this sequel to the problem of calibration but no joy.

  In system Pref NEC display is no longer recognized it be some generic shown screen and the profile seems to be lost.

  In Safe Mode the dock is not black.

  I ran an OSX Yosemite recovery, but this does not seem to have changed anything.

  Can not think of anything else to try contacting Apple Support cat but it was difficult in these conditions and I fell the cat.

  It's weird since it's only a part of the screen with a problem, and the rest is OK.  I don't have a screen to swap to isolate the problem but everything worked fine before.

  Any ideas would be greatly appreciated, thanks in advance.

  

  

  Excellent assistance from the Apple phone is supported, problem solved.

• There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  Apparently, you're trying to use AirPlay to display content that is protected in a way that not only allows the copy.

• Retina MBP display problems

  I vaguely remember that there is a kind of reminder for display problems on some models of MacBook Pro retina. I don't remember the nature of the issue, nor the accurate models who were eligible. I have a 15-inch model, end of 2013, and what I see is pictured below (dead pixels). Can anyone remember if there was a recall and that this issue would be covered?

  

  2011-2013 models.

  To my knowledge the retinas did not have a reminder. However, I got my rMBP 2012 15 "screen changed due to ghosting. I do not know if Apple which is still.

• In the visualization of my photos display problem: I have red spots in different parts of the pictures. Someone knows how to fix this?  I rebooted my MacBook Pro, but it does not solve the problem.

  In the visualization of my photos display problem: I have red spots in different parts of the pictures. Someone knows how to fix this?  I rebooted my MacBook Pro, but it does not solve the problem.

  Details please

  What version of Aperture? Is OS X 10.7.5 as you say correct for your OS? You shoot JPEG or RAW? If RAW device? Wharton has changed since this worked?

  LN

• Mac book air display problem

  having display problems with my macbook air, first version of 2015. When I turn on my macbook, after entering the password and pressing on enter three lines (not really lines they look more like lightning, appear from the top of the screen) in the colors Blue, green and red.

  also when I turn off my laptop just until the display on the top of the screen this thick green line 3 inch appears and goes about a second or 2.

  help someone?

  Thank you

  Try a reset of the NVRAM:

  https://support.Apple.com/en-us/HT204063

  If no success, take a picture of the problem.  Make an appointment at an Apple store genius bar for a free evaluation.  If necessary, show the technician, an image of the screen.

  Ciao.

• having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in

  having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in the colors Blue, green and red.

  also when I turn off my laptop just until the display on the top of the screen that is 2 and a half inch thick green line appears and goes about a second.

  help someone?

  Thank you

  Howdy Yaser of zoysia,

  It seems that your screen displays some graphical anomalies when you connect to your user name. I would use these troubleshooting steps in the following article on the resolution of screens:

  Restart your Mac in safe mode to reset the default display resolution.

  If booting safe mode doesn't resolve the problem, reset your Mac NVRAM and SMC to reset the video ports on your Mac to their default values.

  From: get help with graphics issues on external displays connected to your Mac.

  Thank you for using communities of Apple Support.

• Display problem on my A60 Pro Sat

  The display on my satellite A60 pro features a strip of wide pixelated of 6-7cm at the bottom that hides my mouse cursor and the taskbar. The mouse is still active behind it. Mode full screen using an external monitor is seen. The group changes with my office window or active but is just vertical color bands. What is the problem and can get rid of him.

  Hello, Robert

  Have you changed anything on your device or this occurs suddenly display problem?

  I'm really in idea. If you want you can reinstall the unit with recovery DVDs. If the problem persists it is obviously a malfunction of the display. In this case, you must contact partner in your country.

  If there is some serious hardware issue please let us know.

  Good bye

• The viewer or split display problem: I am getting small white boxes (similar to those seen in the browser) superimposed on my photos. Any ideas how to fix?

  The viewer or split display problem: I am getting small white boxes (similar to those seen in the browser) superimposed on my photos. Any ideas how to fix?  There must be a display problem in the software.

  Have you of the 'show Talking Points' enabled in the view menu? Then you can see small white boxes superimposed on the image in the Viewer.

  

  You can enable or disable on / off power with ⌥F talking points.

• Display problems on Portege M100 connected to the port replicator

  After having connected the M100 to a port replicator, I meet the following:

  Sometimes the first couple of seconds, the external screen is used.
  When Windows XP Pro login screen, external monitor off running and only after the opening of the TFT screen, I can go back by pressing Fn - 5.

  Another question:

  A minute later, after starting windows at 1024 x 768, the Exchange System suddenly resolution
  to 1280 x 1024.

  I manually switch back to 1024 each time, but the system uses 1280 after a reboot.

  Do you have any idea how DIFFICULT 1024 and how to maintain external when it is docked?

  Thanks

  Hello

  I put t know 100 percent how this fix several issues, but you should first check if updates will help you.
  For example, to check on the Toshiba page if the new BIOS, driver card graphic and display Service for external monitor.

  How the words on the display for external monitor Service:

  1.) description of the problem:
  The Intel display driver has a characteristic, as one of its characteristics, to store used display to system shutdown before and use the device to display the images when the system starts the next time, as long as the device is.
  However, this specification has attracted a large number of complaints that images were not displayed on an external monitor, but on an LCD, if systems have been used in the following way:
  1. turn off the system with the images displayed on a LCD screen.
  2. with the LCD closed, anchor the machine to a longshoreman who has a connected CRT monitor.
  3. turn on/off the system will display images on the CRT, while the system is starting.
  However, the display driver will switch the display device on the calendar in Windows JOURNAL to the screen and displays the images on the LCD screen, which is the previous display device.
  4. from the screen LCD is closed, the user will never know where the images are displayed.

  2) corrective action: update the BIOS on V1.30 or more and install the TOSHIBA display driver

• Tecra S1 display problem

  Unfortnately my tecra s1 hit the table of coffee on the ground, the screen immediately turned white. When I rebooted there was no display at all (black only)
  The computer works as I plugged on a screen external and that was very good. I tried to follow various troubleshooting guides online showing how to disassemble the laptop and reinstall the connector of the display on the motherboard, but this did not remedy the problem.

  I noticed coming from the display was a big bunch of wires going into a connector that I reinstalled, on the right hand side of the screen is a white and black wire to a connector and a pink wire that seemed to just float, I couldn't not whence he came. Does anyone have ideas on the subject of this thread or other tips that can help me.

  Thanks in advance

  Hello

  Unfortunately, mate, you won't find any manual disassembly here on the pages of Toshiba. These manuals are not for use public and designed only for the FSA.
  But I think you could google a bit and you should find a few details.

  I think that it is a display problem that I doubt that some loose cables could cause this problem
  In my view, the screen is broken and needs to be replaced
  To do this, you should get in touch with your technician ASP.

  Good luck

• Satellite A200-23U - strange Grapich/display problem

  Hello

  I have a Toshiba Satellite A200-23U and it has a problem... sometimes graphics seems worse suddenly or are destroyed. A simple reboot can operate correctly, but it is very possible to reproduce... when I say that the graphics are getting worse I mean the resolution becomes a little bit worse, and the colors are unacceptable... some waves are created and the areas that were almost of the same color before the problem are now surrounded by a ring-wave , they have only one color with no shading and a few white spots are in these areas... after the restart, everything is ok...!

  I think the problem happens when the laptop is hot, but I'm not sure because he appeared also when the laptop was working only a few minutes in a cold environment and sometimes the device can be turned on for long hours and very hot, but the problem does not appear... Where did you think is the problem?

  The possible reasons, I can think of is the monitor or the cable that connects the graphics card with the monitor. Another reason that I n t think it's quite possible is the graphics card. I think this is less possible because if the problem exists on my laptop and I connect to another external screen as my TV, the problem still exists on the screen of the laptop, but the image on the external monitor is perfect...

  I'm ready to put new and bigger (2 GB I'll put 4gp) memory ram because the graphics card uses the RAM and the RAM is very high work when I play a game or watch a move.

  Do you think it will help or solve problems? What do you think I could do?

  Hi John

  What then? As I see you have good test connect your laptop to the TV. Always is that this test can help you see if the problem can be related to the graphics card, but if there is no problem graphics card is probably OK and this graphic problem must relate to something else.

  Of course, this virtual path, no one will be able to offer the exact diagnosis and say what can be the problem and we can only speculate what part of the material may be troublemaker.

  In my opinion there must be a problem between the motherboard and display. I don t think that the display is faulty, but perhaps the cable must be exchanged, perhaps connector on motherboard make problems. It is not easy to say what to do.

  Fact is that analysis only offer exact answer so I think you need professional help with this.
  Maybe you should contact the closest service Toshiba and ask for help. Let them check it all and ordering new parts if necessary.

  I put t think that you want to risk and disassemble the laptop everything yourself, have you?

• Graphics/display problem - Satellite M60-105

  I'm having a little problem with the display (or graphics). In some programs of CAD (Inventor, Solid Works) 3D solids are displayed with lines that normally are not displayed. "I see the solid. In the games like Doom3, I see only a chequer (Exchequer) with black, the blind, the tasks of rectangle. I tried to update the graphics driver, but the results were the same. Problem is more complex that I have thaught, because I noticed the same problem after formatting HD and mounting of Toshiba Recovery CD. Also, I noticed the same thing happens when I'm trying to change something in the BIOS. Maby some of you have had a problem like this, please help.

  Hello

  Believe me on this path is not easy to say what may be the problem. The explanation of your problem is good, but it will be interesting to see what you mean exactly.

  One of my friends has M60 and I didn't see any display problem on his unit. If the unit is installed with recovery media that produced with other applications, watch DVDs or simply with 3D CAD program?

  It will also be interesting to know what you exactly changed in the BIOS.

• The satellite M60 display problems

  Hello

  I bought a satellite M60 a month ago, and since then, I've been strugling trying to solve a problem that has to do with the display (ATI 700 X mobility).
  When I play some games (the dawn of war, Unreal tournament...) the computer freezes completely, I actually have to force stop it to restart.
  Another problem, that I have seen is with Mixmeister Pro 6, the video playback is erratic, it is as if the computer is unable to handle any overload.

  I tried the upgrade of drivers, nothing works, then I installed the third party Omega drivers, but once again, nothing to do.

  Since the purchase of the M60, I had to correct problems of Wirless and PCMCIA card through driver updates, but there is nothing that I'm be able to do to resolve this display problem.

  I am quite convinced it's a driver issue, but then again, nothing is certain.

  If anyone can help me please I'm getting desperate.

  Hello

  Well, it's not easy to say why it happens but one of my friends has sometimes even appearance but on another unit. If he plays a high-performance games unity cling.
  In my view, this could be a heating problem. Playing games is hard work for the laptop, because all parts (bars of memory, processor, graphics card, etc.) work with max performance and produce a lot of heat. Most laptops are not developed for this.

  However, you should always use the graphics driver from Toshiba. I found the latest version of 15/07/05. It is a display 8.121.050.322A driver. In addition, you must install latest DirectX. I think that it s a 9.1. Check whether the fixes for these games are available.

  Second, if video playback is erratic, it seems that the OS is fully committed.
  In this case, you should check the processes that run in the background of the operating system.
  In addition, try to defragment the HARD disk

  Good bye

• Display problems with the Portege R600 and Win 7

  I have a R600 running windows 7, every two minutes, I have a display problem where where the vertical pixels seem to get every centimeter unaligned, so my screen seems to blur digital in bars across it.

  I have an external monitor attached and get the same problem with or without him. I have tired the driver of toshiba and intel driver.

  It seems to go away if I have windows min and max, but sometimes it doesn't. If I run my mouse an affected area, that it seems in trouble and sometimes it's not all screen.

  A refresh solves it.

  Anyone have any ideas?

  > I have an external monitor attached and get the same problem with or without him.
  Maybe I m wrong but in most cases if these symptoms are seen on the two displays (internal & external) then a graphics chip could be affected
  It would be the worst case, because that would mean that the motherboard needs to be replaced

  But just a question; have you noticed that using the previous Windows OS preinstalled by maybe Toshiba (Win XP or Vista), you must install the image of Toshiba again to verify if this display problem is still visible