877 VPN guard fall
I have a few remote locations running the config below, they remain connected on PPPoE but the VPN tunnel keep interruption or shutters vertically and, finally, stabilizes or drops.
Where am I wrong?
See the version:
Cisco IOS software, software C870 (C870-ADVSECURITYK9-M), Version 12.4 (24) T6, VERSION of the SOFTWARE (fc2)
Config:
Current configuration: 3666 bytes
!
! No change since the last restart configuration
!
version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname ITTest
!
boot-start-marker
boot-end-marker
!
forest-meter operation of syslog messages
activate the secret PASSWORD
activate the password
!
No aaa new-model
clock timezone GMT 0
clock daylight saving time UTC recurring last Sun Mar 01:00 last Sun Oct 02:00
!
!
dot11 syslog
IP source-route
!
!
IP cef
IP domain name gratte.com
name of the IP-server 172.20.0.221
name of the IP-server 172.20.0.222
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
address PRESHAREDKEY key crypto isakmp xauth No. XXX.XXX.XXX.XXX
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac 3DESSHA
!
Profile of crypto ipsec VPN IPSEC
Set transform-set 3DESSHA
!
!
Archives
The config log
hidekeys
!
!
!
!
!
interface Tunnel0
Description - IPSec Tunnel to KX-
IP 172.29.0.1 255.255.255.252
IP ospf mtu - ignore
load-interval 30
source of Dialer0 tunnel
destination tunnel XXX.XXX.XXX.XXX
ipv4 ipsec tunnel mode
Ipsec VPN IPSEC protection tunnel profile
!
ATM0 interface
no ip address
No atm ilmi-keepalive
PVC 0/38
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
IP 172.29.0.10 255.255.255.252
IP nat inside
IP virtual-reassembly
!
interface Dialer0
the negotiated IP address
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
PPP chap hostname username
PPP chap password
PPP pap sent-username username password
!
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 Dialer0
IP route 172.16.0.0 Tunnel0 255.240.0.0
IP route 172.29.0.0 255.255.0.0 Vlan1
no ip address of the http server
no ip http secure server
!
The dns server IP
overload of IP nat inside source list 100 interface FastEthernet0
!
access-list 100 deny ip 172.29.0.0 0.0.255.255 172.16.0.0 0.0.240.255
access-list 100 permit ip 172.29.0.0 0.0.255.255 everything
!
!
!
public RO SNMP-server community
!
control plan
!
!
Line con 0
password
opening of session
no activation of the modem
line to 0
line vty 0 4
password
opening of session
!
max-task-time 5000 Planner
NTP 172.20.0.221 Server
NTP 172.20.0.222 Server
end
When I originally did this config, I was familiar with cisco switches and had to learn all the tricks of router.
Now I have more knowledge; I tried to make a new configuration, the problem with this is that I can't even the VPN tunnel to the top first... this config is below (same h/w and f/w)
ITTest #show run
Building configuration...
Current configuration: 6053 bytes
!
version 12.4
no service button
tcp KeepAlive-component snap-in service
a tcp-KeepAlive-quick service
horodateurs service debug uptime
Log service timestamps uptime
encryption password service
sequence numbers service
!
hostname ITTest
!
boot-start-marker
boot-end-marker
!
forest-meter operation of syslog messages
logging buffered 10240
recording console critical
!
No aaa new-model
clock timezone GMT 0
clock daylight saving time UTC recurring last Sun Mar 01:00 last Sun Oct 02:00
!
!
dot11 syslog
IP source-route
DHCP excluded-address IP 172.30.58.1 172.30.58.99
!
IP dhcp pool dhcppool
import all
network 172.30.58.0 255.255.255.0
router by default - 172.30.58.1
172.30.58.1 DNS server 172.20.0.221 172.20.0.222
domain gratte.com
Rental 7
update of arp
!
!
IP cef
inspect the name firewall tcp IP
inspect the name IP firewall udp
inspect the name IP firewall cuseeme
inspect the h323 IP firewall name
inspect the name IP rcmd firewall
inspect the name IP firewall realaudio
inspect the name IP firewall streamworks
inspect the name IP firewall vdolive
inspect the name IP firewall sqlnet
inspect the name IP firewall tftp
inspect the name IP firewall ftp
inspect the name IP firewall icmp
inspect the IP sip firewall name
inspect the name IP firewall esmtp max / data 52428800
inspect the name IP firewall fragment 256 1 maximum period
inspect the name IP firewall netshow
inspect the name IP firewall rtsp
inspect the name IP firewall pptp
IP inspect name lean firewall
no ip bootp Server
no ip domain search
IP domain name gratte.com
name of the IP-server 172.20.0.121
name of the IP-server 172.20.0.120
!
!
!
!
file verify auto
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
address PRESHAREDKEY key crypto isakmp xauth No. XXX.XXX.XXX.XXX
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac 3DESSHA
!
110 cm-cryptomap map ipsec-isakmp crypto
defined peer XXX.XXX.XXX.XXX
Set transform-set 3DESSHA
match address 110
!
Archives
The config log
hidekeys
flash path: config
writing-memory
!
!
IP tcp selective ack
tcp IP timestamp
!
!
!
ATM0 interface
no ip address
NAT outside IP
IP virtual-reassembly
No atm ilmi-keepalive
PVC 0/38
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
IP 172.30.58.1 255.255.255.0
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1452
!
interface Dialer0
the negotiated IP address
IP access-group 101 in
no ip redirection
no ip unreachable
IP mtu 1492
inspect the firewall on IP
NAT outside IP
IP virtual-reassembly
encapsulation ppp
no ip-cache cef route
no ip route cache
no ip mroute-cache
Dialer pool 1
Dialer-Group 1
No cdp enable
PPP chap hostname username
PPP chap password
PPP ipcp dns request
failure to track PPP ipcp
cm-cryptomap crypto card
!
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
The dns server IP
IP nat pool pool1 172.30.58.0 172.30.59.0 netmask 0.0.0.255
the IP nat inside source 1 interface Dialer0 overload list
overload of IP nat inside source list 105 interface Dialer0
!
access-list 1 permit 172.30.58.0 0.0.0.255
Note access-list 1 local LAN.
Note access-list 2 where management can be done from.
access-list 2 permit 172.30.58.0 0.0.0.255
access-list 2 allow 172.20.0.0 0.0.255.255
Note access-list 3 traffic does not check the intrusion detection.
access-list 3 refuse 172.20.0.0 0.0.0.255
access-list 3 allow a
Notice the traffic is allowed to enter the router of the Internet access list 101
access-list 101 permit ip 172.20.0.0 0.0.0.255 172.30.58.0 0.0.0.255
access-list 101 deny ip 0.0.0.0 0.255.255.255 everything
access-list 101 deny ip 10.0.0.0 0.255.255.255 everything
access-list 101 deny ip 127.0.0.0 0.255.255.255 everything
access-list 101 deny ip 169.254.0.0 0.0.255.255 everything
access-list 101 deny ip 172.16.0.0 0.15.255.255 all
access-list 101 deny ip 192.0.2.0 0.0.0.255 any
access-list 101 deny ip 192.168.0.0 0.0.255.255 everything
access-list 101 deny ip 198.18.0.0 0.1.255.255 all
access-list 101 deny ip 224.0.0.0 0.15.255.255 all
access-list 101 deny ip any host 255.255.255.255
access-list 101 permit udp any any eq non500-isakmp
access-list 101 permit udp any any eq isakmp
access-list 101 permit esp a whole
access-list 101 permit tcp any any eq 1723
access-list 101 permit any one
access-list 101 deny icmp no echo
access-list 101 deny ip any any newspaper
Note access-list 102 allowed traffic to enter the Ethernet router
IP access-list 102 permit any host 172.30.58.1
access-list 102 deny ip any host 172.30.58.255
access-list 102 deny udp any any eq tftp log
access-list 102 permit ip 172.30.58.0 0.0.0.255 172.20.0.0 0.0.0.255
access-list 102 deny ip any 0.0.0.0 0.255.255.255 connect
access-list 102 deny ip any 10.0.0.0 0.255.255.255 connect
access-list 102 deny ip any 127.0.0.0 0.255.255.255 connect
access-list 102 deny ip any 169.254.0.0 0.0.255.255 connect
access-list 102 deny ip any 172.16.0.0 0.15.255.255 connect
access-list 102 deny ip any 192.0.2.0 0.0.0.255 connect
access-list 102 deny ip any 192.168.0.0 0.0.255.255 connect
access-list 102 deny ip any 198.18.0.0 0.1.255.255 connect
access-list 102 deny udp any any eq 135 newspaper
access-list 102 tcp refuse any any eq 135 newspaper
access-list 102 deny udp any any netbios-ns eq journal
access-list 102 deny udp any any netbios-dgm eq journal
access-list 102 tcp refuse any any eq 445 newspaper
access-list 102 permit ip 172.30.58.0 0.0.0.255 any
IP access-list 102 permit any host 255.255.255.255
access-list 102 deny ip any any newspaper
Note access-list 105 NAT traffic
access-list 105 deny ip 172.30.58.0 0.0.0.255 172.20.0.0 0.0.0.255
access-list 105 allow ip 172.30.58.0 0.0.0.255 any
access-list 110 note VPN Site-to-Site
access-list 110 permit ip 172.30.58.0 0.0.0.255 172.20.0.0 0.0.0.255
access-list 110 deny ip 172.30.58.0 0.0.0.255 any
Dialer-list 1 ip protocol allow
!
!
!
Server SNMP community blooby RW
public RO SNMP-server community
!
control plan
!
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
opening of session
!
max-task-time 5000 Planner
end
Any suggestions on the configs or above would be greatly appreciated!
Thank you!
-Damo.
xDSL has a major defect. If you have a bad copper xDSL to your premises you get very bad synch and line speed.
Look here in Australia. Our cabling in copper in the premises of the property (business or residential) is so bad that every time it rains, the water gets into cracks in the cable and causes problems. Unfortunately, our phone company can't fix these cables because they just want to take our money.
It is the same with you. Take the results you've posted and show it to your phone company and demand for fixed lines.
Tags: Cisco Network
Similar Questions
-
700 - 430qe envy: Wifi guard fall immediately after the connection manually
Wireless of my new office as envy worked well for about six weeks and suddenly can't stay connected. I have at least 7 other devices using the same router wireless without any problem. The connection drops at seconds. Sometimes I can get a Web page to load but not a second. I changed the channel on the Router 1, 6 and 11, but that did not help. I also deselected the option to disable the network card in the computer to save energy, but even once, it did not help. I can't find advice on the internet that seems to help.
Network adapter: Broadcom BCM43142
Windows 8.1
Hello @sharps34,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.
I read your post on how the wireless connection between your computer and network guard falling intermittently, and I'd be happy to help you in this case!
To re - establish a coherent link between your computer and the network, I recommend later in this document on troubleshooting wireless network and Internet (Windows 8). This should help to run a diagnostic on your system using the network and Internet troubleshooting, as well as measures to maintain your system over the wireless network.
In addition, I suggest also follows the steps below to ensure that your power management settings do not interfere with
the connection to the network:
1. open DEVICE MANAGER
2. open the NETWORK CARDS
3. right click on the WiFi adapter for the pc and left click on PROPERTIES
4. click on POWER up.
5. remove the check mark beside : ALLOW the COMPUTER TO TURN THIS DEVICE SAVE START STOP
6. click on OK
7. close DEVICE MANAGER and test. -
Connections Satellite U200-192 Wifi guard fall power battery only with the mode on and off.
Hi all
The new satellite works well with internet, etc, when it is connected with the lan cable.
Wifi mode guard fall on and outside with the linksys DI-614 router + when you work with the battery, but not when it is connected with the power cable!
Thanks 4 suggestions
GilgenuldoPost edited by: gilgenuldo
Hello
For me it s clear case interruptions of connections WLan because the WLan card is trying to save portable power.
This is nothing unusual. Of course, you can simply disable this option:
Go to Device Manager, select the wireless network card and chose properties.
In the Advanced tab, you should find several settings and disable the power saving option.Concerning
-
WiFi guard falling on my newly purchased Aspire V5 - 122P
My WiFi guard fall on my Aspire V5 - 122P. I don't know if there is a problem with Windows 8, or if it is a product problem Acer? Any suggestions as to how I can keep a stable WiFi without having to reconnect to the router whenever it falls? Last night, I had to log at least 6 times before I finally gave up and waited until morning to use my desktop (which I now use this type).
Hello...
You can install the new wireless network card driver: http://global-download.acer.com/GDFiles/Driver/Wireless%20LAN/Wireless%20LAN_Atheros_10.0.0.245_W8x6...
Here is the link to download and install the new update to the BIOS: http://global-download.acer.com/GDFiles/BIOS/BIOS/BIOS_Acer_2.08_A_A.zip?acerid=635112704441155009&S...
-
Site-to-Site VPN IPSEC falls intermittently
Site-to-Site VPN IPSEC falls intermittently
I am currently having a problem with a VPN from Site to Site traffic not only not intermittently. When the problem occurs, I can't Ping the remote site to the AC Site. But I can solve the problem by Pinging from HQ at the Remote Site. My network is currently configured as follows
-------HQ------
7.0 (4) version of pix 515 with card Ethernet 4 ports.
Outside of the interface connected to the Broadband DSL link.
Outside2 Interface connected to the second link DSL broadband
-Distance-
I have 4 Remote Sites. 2 sites connect you to each connection to wide band at HQ to spread the load to HQ
6.3 (5) pix 501 version
# The problem #.
All VPN establishes successfully to the HQ Pix
Intermittently, a remote site will report that they cannot connect to servers/services in the HQ. When I do a show crypto ipsec's and see the crypto isakmp his headquarters there is no entry for the remote site. However when I do the same on the remote site there is an entry for the HQ. With debugging on the remote site pix I try to ping from a pc to the HQ server and I get the following (see below). If I do a "ipsec Isakmp security association claire crypto ' and ' clear crypto ipsec his ' on the pix of remote site, then I can successfully ping all servers in headquarters.
This problem seems to have taken place only when I upgraded the pix of a 501 to 515 and added another 2 remote sites and a second broadband, as described above. I'm afraid that there is a problem with software version 7 Pix. Any advice would be greatly appreciated.
Console record Carrick-PIX01 (config) # 7
Carrick-PIX01 (config) # ter Lun
Output Carrick-PIX01 (config) #.
Carrick-PIX01 # debug crypto ipsec
Carrick-PIX01 # debug crypto isakmp
Carrick-PIX01 #.
ISAKMP (0:0): sending of NAT - T vendor ID - rev 2 & 3
ISAKMP (0): early changes of Main Mode
ISAKMP (0): retransmission of the phase 1 (0)...
ISAKMP (0): retransmission of the phase 1 (1)...
ISAKMP (0): retransmission of the phase 1 (2)...
Carrick-PIX01 #.
Carrick-PIX01 #.
ISAKMP (0): retransmission of the phase 1 (3)...
Carrick-PIX01 #.
Carrick-PIX01 #.
ISAKMP (0): retransmission of the phase 1 (4)... IPSec (key_engine): request timer shot: count = 1,.
(identity) local = OUTER-IP, distance = 86.43.74.16,.
local_proxy = LAN-OFFICE/255.255.255.0/0/0 (type = 4),
remote_proxy = 194.x.x.x.x.255.0/0/0 (type = 4)
ISAKMP (0): delete SA: CBC EXTERNAL IP, dst 86.43.74.16
ISADB: Reaper checking HIS 0x10c167c, id_conn = 0 DELETE IT!
Peer VPN: ISAKMP: Peer Info for 86.43.74.16/500 not found - peer: 1
ISADB: Reaper checking HIS 0x10ca914, id_conn = 0
Can force you the ISAKMP Keepalive, value from IPSec Security Association idle time and on the other. The problem should be solved
ISAKMP crypto keepalive 30
Crypto ipsec security association temps_inactivite 60
Let me know if it helps
-
Hello
We have a pair of AP1242 configured as point to point. He worked for centuries, and then all of a sudden the guard falling radio link. There is no change in the configurations and equipment and the way that he setup. The values on the two AP signal strength is good, but one thing I notice is on the other access point, SNR values going to 3dB low then it will go high of more than 100, we have replaced the AP and cable is connected to the antenna but we always have the same question. I think there could be some question on the antenna or interference that have cause going on this issue. is it normal for SNR value change value to very low and then high?
Thank you.
to me, it looks like interference...
Why don't you try to use the 802. 11 radio and see if it is the same behavior?
or maybe, check the use of channels, or increase a few times to improve the bridge link.
-
Simple Question on 877 VPN functionality
Where can I find namely how the router throughput is affected when there are configured VPN Tunnels? or if there is someone who can give me this info... I have just didn? find it in the data sheet. Thank you
Refer to page 61
http://www.Cisco.com/application/PDF/en/us/guest/NetSol/ns171/c649/ccmigration_09186a008073a0c5.PDF
871 and 877 have the same architecture.
or
http://www.Cisco.com/Web/partners/downloads/765/tools/quickreference/vpn_performance_eng.PDF
-
Cisco 877 + VPN Site to Site
Hello
I'm new im this forum.
I've set up a Site VPN site with 2 Cisco 877.SITE A:
Address IP Adreess public: static
Internal IP Adrees: 192.168.0.XXX
Mask: 255.255.255.0SITE B:
IP address public Adreess: Dynamics
Internal IP address: 192.168.2.XXX
Mask: 255.255.255.0I managed to do a ping on both sides, but I can't access file shares, and could rdp on any server in site A, by the internal IP address.
Fix, is the SITES A and B SITE startup configs.
Could you please someone help me?
Hi Marcos,
Really happy to know that the problem is solved. There is no need to apologize. Please mark this message as answered if there is nothing more.
Rregards,
Assia
-
Cisco 877 VPN router LAN access
I have spent much time already trying to figure out why I can't reach the LAN behind the router connecting through VPN, I thought it would be easier to ask people with more experience than me.
So, here he goes, this is the configuration of a router 877 adsl with some ACL defined for security and NAT/PAT, the VPN connects to customer VPN CIco however I don't see anything on the LAN to the remote computer (for example: cannot ping the router or server on the local network)
Also, since the router I can not ping the remote VPN computer when connected... I already tried a lot of different things, but my knowledge of cisco is limited, so I hope someone in this forum can sort it with little effort or change in this config... I replaced the ip addresses and passwords for security reasons.
In a Word, what is false or absent in this config which is not let me reach the LAN when docked hollow VPN?
Appreciate the help:
version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec localtime
encryption password service
!
hostname My877Router
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 XXXXXXXXXX
!
AAA new-model
!
!
AAA authentication login default local
connection of local AAA VPN authentication.
AAA authorization exec default local
local authorization AAA VPN network
!
!
AAA - the id of the joint session
clock timezone CST 9 30
!
Crypto pki trustpoint TP-self-signed-901674690
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 901674690
revocation checking no
rsakeypair TP-self-signed-901674690
!
!
TP-self-signed-901674690 crypto pki certificate chain
certificate self-signed 01
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
quit smoking
dot11 syslog
IP cef
!
!
inspect the IP router-traffic tcp name _OUTBOUND_
inspect the IP router traffic udp name _OUTBOUND_
inspect the name _OUTBOUND_ http IP
inspect the IP name _OUTBOUND_ https
inspect the IP dns _OUTBOUND_ name
inspect the IP router traffic icmp name _OUTBOUND_
no ip domain search
IP domain name mydomain.com.au
Name A.B.C.D IP-server
IP-name x.y.z.w Server
!
aes encryption password
!
!
username admin privilege 15 secret 5 #$% ^ & *.
Admin2 username privilege 15 secret 5 #$% ^ & *.
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
life 3600
!
ISAKMP crypto group configuration of VPN client
key 6 #$%^&_)(*&^%$%^&*(&^$
DNS 192.168.100.5
domain mydomain.com.au
pool VPN
ACL 100
Max-users 5
Max-Connections 1
netmask 255.255.255.0
!
86400 seconds, duration of life crypto ipsec security association
!
Crypto ipsec transform-set esp-3des esp-sha-hmac vpn1
!
Crypto-map dynamic dynmap 11
Set transform-set vpn1
market arriere-route
!
!
list of card crypto dynmap customer VPN authentication
card crypto dynmap VPN isakmp authorization list
client configuration address card crypto dynmap initiate
client configuration address card crypto dynmap answer
dynmap 11 card crypto ipsec-isakmp dynamic dynmap
!
Archives
The config log
hidekeys
!
!
!
type of class-card inspect VPN-match-all traffic
game group-access 100
!
!
type of policy-card inspect PCB-pol-outToIn
class type inspect VPN traffic
inspect
!
!
!
!
ATM0 interface
no ip address
no ip redirection
no ip unreachable
no ip proxy-arp
route IP cache flow
No atm ilmi-keepalive
PVC 8/35
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
DSL-automatic operation mode
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
Description LAN_INTERFACE
IP 192.168.100.1 address 255.255.255.0
no ip redirection
no ip proxy-arp
IP nat inside
IP virtual-reassembly
route IP cache flow
IP tcp adjust-mss 1452
!
interface Dialer0
ADSL description
the negotiated IP address
IP access-group 101 in
Check IP unicast reverse path
no ip redirection
no ip unreachable
no ip proxy-arp
inspect the _OUTBOUND_ over IP
NAT outside IP
IP virtual-reassembly
encapsulation ppp
route IP cache flow
Dialer pool 1
No cdp enable
Authentication callin PPP chap Protocol
PPP chap hostname [email protected] / * /
PPP chap 7 76478678786 password
card crypto dynmap
!
local pool IP VPN 192.168.200.1 192.168.200.10
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 Dialer0
!
no ip address of the http server
local IP http authentication
no ip http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
IP nat inside source static tcp 192.168.100.9 443 interface Dialer0 443
IP nat inside source static tcp 192.168.100.9 25 interface Dialer0 25
IP nat inside source static tcp 192.168.100.9 1352 Dialer0 1352 interface
IP nat inside source static tcp 192.168.100.6 3389 3389 Dialer0 interface
IP nat inside source static tcp 192.168.100.7 3389 interface Dialer0 3391
IP nat inside source static tcp 192.168.100.3 8443 interface Dialer0 8443
the IP nat inside source 1 interface Dialer0 overload list
!
access-list 1 permit 192.168.100.0 0.0.0.255
access-list 100 permit ip 192.168.200.0 0.0.0.255 any
access-list 101 permit tcp any any eq 443 newspaper
access-list 101 permit tcp any any eq smtp newspaper
access-list 101 permit tcp any any eq 1352 newspaper
access-list 101 permit tcp A.B.C.D host any newspaper
access-list 101 permit tcp host x.y.z.w any log
access-list 101 permit tcp host r.t.g.u any log
access-list 101 permit udp any host x.x.x.x eq isakmp newspaper
access-list 101 permit udp any host y.y.y.y eq non500-isakmp log
access-list 101 deny ip any any newspaper
access-list 102 deny ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255 connect
access-list 102 permit ip 192.168.100.0 0.0.0.255 any what newspaper
Dialer-list 1 ip protocol allow
not run cdp
!
!
route allowed sheep 11 map
corresponds to the IP 102
!
!
control plan
!
Banner motd ^ C
Unauthorized access prohibited! ^ C
!
Line con 0
exec-timeout 20 0
no activation of the modem
line to 0
line vty 0 4
privilege level 15
entry ssh transport
!
max-task-time 5000 Planner
x.x.x.x SNTP server
y.y.y.y SNTP server
endMy877Router #.
Doesn't look like anything sent through the VPN tunnel. Decrypt the counter does not increase.
Can you please try to connect by a different ISP and see if that makes a difference?
You can also try to connect from another PC and see if that makes a difference?
The configuration on the router seems correct to me.
-
Wireless internet guard fall on my computer pavilion dv6 Notebook PC laptop
A week ago I bought the HP pavilion dv6 laptop and after a few days im having problems connecting to my Wi - Fi.
When I use the internet laptop works but after a while, he falls and I can't use internet and then I usually launches solve programs to restore the connection and after awhile I get internet back on, but after a while I lose my internet again. It's really fustrating and lose a lot of my time.
My other laptop that also uses the same wireless internet seems to work perfectly and the internet never falls on it, it's just this dv6. My main PC, which has a wired connection to the internet also works perfectly.
Please can someone help me, this is usually a drop in my internet is really problematic
System
Windows 7 sp1 64 bi
Product LS251EA #AB number
Hello
This last driver Intel to give a try and see if you get improvement
You only need the driver (top download) If you allow Windows to manage your wireless connection.
Paul
-
Z5 double guard falling mobile data signal
Purchased and received my Xperia Z5 Dual of a seller decently well known on Amazon a few days ago. After putting my SIM card, I got mobile signal (advocate and text), but no data, so I took it to T-mobile, and they got that running. Since then, my freqnently data falls to zero bars of signal, then comes back to the top in about a minute then drop again a minute later. The wifi signal seems to do that too, although it seems to be in bars full all the time in my house, when I play a mobile game, I can tell he falls signal when it is lagging on every few seconds.
Should I return it as broken and buy a new one? I am inclined to think that the question is not on the end of my career, because I had no signal with this SIM card problem in my last phone, a very old Moto X. My friend suggested it was probably a hardware problem (specifically, the faulty antenna Board), but I don't know a lot about hardware, so I don't know whether to take his suggestion at face value or not.
Hi anastvns,
Do you get the same results with WCDMA/GSM without selected LTE?
-
My C7280 guard fall Wi - Fi for Windows7 64 bit
I have a Belkin N Router + wireless running the latest Firmware (v 1.01.19) and a HP Pavilion dm1 Notebook running Win 7 64 bit. However, the wireless connection to the printer keeps falling. He considers that the printer is offline and extremely difficult to restore. Sometimes it takes several reboots the PC, printer and router, and sometimes it does not. Y at - it a solution or should I set up a static IP address? If so, how?
Did ever set you a static IP address for the printer? Follow these steps:
-Print a the front of the printer Network Setup Page. Note the IP address of the printer.
-Enter the IP address in a browser to reveal the internal settings of the printer.
-Choose the network tab, then wireless along the left side, then on the IPv4 tab.
-On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
-Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
-Enter the IP of your router (on the Page of the Network Config) for the gateway.
-Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS.
-Click 'apply '.Now, stop the router and printer, start the router, wait, and then start printing.
After that, you will have to redo 'Add printer' using the new IP address.
-
Cisco 877 VPN - two routers remote connection to the head office
Hi all.
Our headquarters has a 877.
Our two remote sites also have 877 and they have a permanent tunnel in 877 headquarters which works OK.
My problem is that two remote sites cannot talk to each other - but they can talk to the seat of fines.
I guess I sort of NAT problem - so I'll post the relevant configs and if someone could take a look and point me in the right direction, I had to be very happy!
Head office config is a txt 192.168.16.5 file
Remote site 'Riversdale' is the 192.168.17.1 text file
Remote site 'Tynewydd' is the 192.168.18.1 text file
How have you checked with pings? Is this an internal host to internal host?
You can check with pings between rays? Please use the internal interface of rays for both source and destination addresses. And send me 'Show details crypto session' of all the routers both before and after the sending of pings.
One thing I forgot in your rays (both) config file is on NAT. Please reorganize both deny entries followed first allow entry.
access-list 100 deny ip 192.168.17.0 0.0.0.255 192.168.16.0 0.0.0.255
access-list 100 permit ip 192.168.17.0 0.0.0.255 any
access-list 100 deny ip 192.168.17.0 0.0.0.255 192.168.18.0 0.0.0.255
-
We are setting up a asa 5505 with anyconnect. But vpn-pool local traffic network is to be droppped. but the traffic from the inside network to the vpn client is not being deleted. Any help
Can you also clear line 'access-group anyconnect in external interface' bur leave a vpn-filter configuration?
You can also add a line to deny a whole at the end of each ACL to see which blocks the traffic.
Best regards.
-
[Config] 877 VPN - please help
Hello
I wonder if someone could help me because I am quite stuck
I am trying to establish the following VPN configuration?
Remote user Mobile > Internet > Cisco VPN > server (service)
With the help of SDM I selected 'Easy VPN Server' deployment.
I am able to connect remotely via the telephone dialler customer of Cisco, connection is made very well and I am able to ping 192.168.1.1 where the standard ping results are returned.
I have a server that is running IIS on 192.168.1.20 but I can't ping the server? I don't want to install software on this server that users can synchronize remotely with and I'm not sure what to do.
Attached configuration
Thanks in advance
Hello
Somethings to check.
a. What is the default gateway on the server?
b. the server has more than one NETWORK card?
can c. If Yes, you close the second NETWORK card and see if it works.
d. you can run debug on the router to see if we even get the package and respond to the customer.
Here are a few troubleshooting steps.
Thank you
Gilbert
Maybe you are looking for
-
I have "ve been 'download' for more than six hours!
I tried 3 different downloads. Firefox seems to be stuck.
-
Como instalar el dispositibo audio
Hola nesesito mucha Ahmed ayer estaba goes musica y mark subirle y despues wedding escucho nada y el audio tiene una tachita y no puedo is him bringing in all partes no puedo ayundenme in el audio dio not of than no hay salida to enable audio device
-
How can I uninstall/reinstall the games?
I'm having a problem of the pixalating to display only when I try to play all the games that come with Windows 7, hearts, Minesweeper, etc.. There are no other games installed. This is on a Dell Studio 1537 laptop. When I open any game, there are sma
-
my computer compaq presario cq56 laptop does not recognize my usb drive hp usb flash drive v195b
I have a lot of problems with flash drives and card readers that plug about my ports detected usb, I just buy a new drive 16 GB flash (HP) as above is said on this plug and play, but when I plug it I can't, there is no prompt and if I remove usb it d
-
Create safer self-signed certificates on IOS router?
I use a router in 1921 and use partially as an AnyConnect (WebVPN) server for remote access in the location. The certificate I used was a self-signed certificate & trustpoint generated on the router. I am running as the last IOS available track to