A740 - remove the Base cover
Hello
I am trying to remove the cover of a model A740, but it seems virtually impossible. The coverage seems to be one piece and will be simply not to remove. Equipment, manual, in this case, doesn't give me all the tracks. Someone at - he had luck with this and that could possibly help?
Thank you
Petter
Problem solved!
You must remove the rubber feet on the base. Below, you will find the 4 remaining screws that must be removed before you can remove the base of the cover.
You can use a small screwdriver to lift loose rubber feet. They will be set to the base once you are finished.
Tags: Lenovo Desktops
Similar Questions
-
2015 envy 17 t-n100 I76700HQ: how to remove the back cover of a 17 t-n100 envy?
Hello, I upgrade my Ram and hard drive 16 GB of Ram and 1 TB ssd drive. I looked everywhere, but for the life of me I can't find any info on how to remove the back cover. There are utube videos that show older versions, but they are completely different. You can provide any help would be greatly appreciated.
Thank you
Hello
Did you know that it's a job for parts of authorized service provider ? If you wish, for the RAM, try it please:
1. turn off the computer. If you don't know if the computer is off or in hibernation, turn on the computer and then stop it through the operating system.
2. remove power from the computer by disconnecting the power cord from the computer.
3. disconnect all external devices from the computer.
4. remove the battery (see battery on page 27).
5. remove the optical drive (see optical drive on page 28).
6. remove the bottom cover (see low cover on page 31).as mentioned on page #38 of the following record:
http://h10032.www1.HP.com/CTG/manual/c04696907.PDF
DIY will void the warranty.
Good luck.
-
Can I remove the base of an iMac of 2013?
I read that the later models of iMac, (I have a 2013) the base cannot be deleted.
I need to lower my iMac, either by removing the base and attach a mount,
'He' placed on a support of ledger, or some kind of support.
Any suggestion would be appreciated.
Thank you!!
RM. Austin
Unfortunately, the answer is no, you cannot remove the base. It is affixed permanently on the computer chassis. However, you can find third-party wall brackets. For example, https://www.ergotron.com/portals/0/html/AppleAdapter/VESAguide2.html
-
I want to know how to remove the back cover of my HP product name: HP Pavilion Sleekbook 15 to install the new memory? All site shows HP Web is how remove caches memory. Unfortunately, with the newer models like mine, the whole back cover needs to be removed. I have tried in vain to remove it, but so far all that I managed to do is scratch my cover. If anyone can help?
Dear David
It's a very good idea, it would also be a good excuse to use my new phone for this. So I'll say thanks again for the good advice. Have a great weekend you Mr. As I said earlier, you're a star...
Yours Sincerely
Alan
-
CLIQ XT: Remove the battery cover
Has anyone found out how to remove the battery cover? I have tried since the 18th to remove this stupid thing and can not >
-
I'm looking for instructions on how to remove the base from a desire to HP TouchSmart 23 "in order to mount on the wall.
You want:
http://support.HP.com/us-en/document/c03437336
Enjoy!
-
Remove the back cover of my Y710
Hi all
I tried to remove the back cover of my Y710 by unscrewing all the screws that are visible, but the lid in the form of S always seems to be screwed. Just use a little more force, or there at - it a secret to this?
Just for the record, I am trying to replace the HARD drive.
I thank in advance
Steve.
Success!
The HARD drive is under the Panel S shaped. To remove the Panel S shaped first remove the screws of 7 or 8. Then, start to lift the Panel upwards from the back (ie the closest edge of the hinge). The front edge of the Panel must be slid and can be popped up, as can the other edges.
Thanks for your help,
Steve
-
How can I remove the base on a screen LCD S232HL?
I am moving and you need to remove the base of a screen LCD S232HL can anyone help?
I think you have to shoot, place the monitor on a flat surface with a cloth under the screen to prevent scratches and pull on the base.
-
Accidentally that hidden/removed the base Panel (the one with the shadows, made highlights, contrast, exposure) to develop module. I was clicking on the exposure slider when my mouse slipped and I clicked on something. How to do back panel?
Make a right-click on any other Panel name develop. In the menu that appears, put a check mark next to the base.
-
How to remove the lower cover of the Satellite S50D-B-103
How can I open the back of my Satellite S50D-B-103 (botton)? I have to put in some more memory.
You just need to remove all screws in the base, then place the lid off the coast.
But you can get an ASP to do as this may void the warranty or something can break.
-
XPRT: How to remove the battery cover?
How to remove the cover of the battery on the XPRT correctly? You lift up the slot on the bottom next to the mic or what? Nothing really seems to drag...
Hold the phone upside down, the back facing you, place your middle finger
into the slot that is located just above the speaker.
A little pull with your middle finger back enough to place your index finger and
ring finger away from each side.
Place your thumb in the center of the lid, close the Motorola "M" logo
Pull with your index, middle and ring finger with your thumb as
leverage and the back will be open.
You can remove the lid of the compartment from the rest of the way by pulling
you.
The back door is pretty thin, so be careful not to overdo with
your thumb, you try not to snap paused just half, the 'seal '.
the bottom of the phone.
On Saturday, June 25, 2011 at 22:19, rwhite
-
You can remove the back cover of the Milestone 2?
Hi I just got my Milestone 2 today (9 December). Because I had to use my old phone for charging the battery I assembled the phone without the SIM card. I want to insert the SIM card now I can't remove the back. I try to push the lens of the camera and move it for abour one third of a millimeter, but no more. I broke my thumb nail trying to push even more away, without result. I can move it back again. Any suggestions?.
Maybe your back is very tight, but I can remove it easily mine in holding the phone face down, and using the apartment of my thumbs in the back and pushing the lens on the camera. It moves about 2mm and can then be raised.
Good luck.
See you soon,.
Steve.
-
remove the base by script files
Hi all.. my oracle 11g generates files of basis whenever there is a problem in the whole of the structure. I managed my server db on solaris 10 machines. can u please guide me how to write a script in solaris that monitors the/U01 directory, at the frequency of 15 minutes, and if it fills up more than 90%, remove (rm - rf *) all the files in/u01/cdump base?
I am new to solaris. any help wud highly appreciated.
Thanks in advanceGrand... I am really grateful for your help... I'll write and implement the work immediately (with 70%). then I willl test it by placing the data in dir... Thank you
There are a few labels for the forum, see [Forums label / Reward Points | http://forums.oracle.com/forums/ann.jspa?annID=718]
Thank you.
-
How to remove the rear cover to the hard drive.
I own a laptop, a HP Pavilion dv6, System ID 3583, product ID LY076UA.
When you turn on the laptop hard disk cover has no screws, it seems to be stuck in the chassis. What to do, take a knife and try to lift up?
All the diagrams that I find slightly different models shows screwed on covers HD online.
I also need to replace the fan, I would not mind a maintenance manual appropriate.
Hello
This is the HP Pavilion dv6 Maintenance & Service Guide. There's a latch of service you must release to access with the optical and hard drive. This is why there is no screws.
Best regards
ERICO
-
Unit will stop dying just after removing the base
My Palm continues to falter after that I loaded and synchronized it. Can you replace the batteries on the devices?
Try a search on google for "Battery Palm T3" and you will find several places that sell a replacement battery for the T3 and include instructions for replacement.
If you don't want to do it yourself, I would go around (again, google is your friend, 'palm t3 repair' or the glance at the research of battery to see if the places that sell batteries also offer installation services). I would bet that these types of places will be much cheaper than to go through Palm, since this unit is out of warranty and you should pay $199 to fix it through this page: http://kb.palm.com/wps/portal/kb/na/tungsten/t3/unlocked/supportservices/page_en.html
P.S. I'm moving this to the Board, also.
Maybe you are looking for
-
OS update 10.11 El Capitan, causing the crash MacPro
MacPro (mid-2010) 2.8 GHz Quad-Core with 32 GB of RAM ECC DDR3 and an OWC SSD 480 GB Accelsior, AMD Radeon HD 7950 graphics card. I tried to upgrade 10.10.5 to 10.11 three times with the same result - startup gets about 80% of fact and accidents with
-
Reinstalled XP; Freezes reboot
I did a complete reinstall of XP on Dell Inspiron 8100 laptop. I received a large batch of Microsoft updates auo requiring a restart of the computer. Everything is OK. Later, I received another important batch of 61 automatic updates, and the compute
-
Version of Windows 64-bit Server and the remote your 2161DS-2 console switch
I have a Dell 2 your 2161DS remote console switch connected to the servers of 7 or 8. Recently, I removed several servers and install 3 new devices; a Windows Server 2003 (32-bit) system; a system of Windows Unified Data Storage Server 2003 (64-bit)
-
Wifi blackBerry Smartphones No. option in manage connections
Hello I try to use wifi via my home network. I understand that I need to enable wifi in 'manage connections '. BUT I don't have a wifi option in 'manage connections '. Am I missing something?
-
How can I solve this problem?Exit code: 6Please see the faults and warnings below for troubleshooting. For example, ERROR: DS003, DW050... WARNING: DW036...-------------------------------------- Summary ---------------------------------------1 fatal