ACI - cannot reach hosts outside the fabric until the traffic is inititated from a host outside in a host connected to the fabric

Similar Questions

• ASA5510 VPN L2L cannot reach hosts on the other side

  Hello experts,

  I have an ASA5510 with 3 VPN L2L and remote VPN access. Two VPN L2L, Marielle and Aeromique no problem, but for VPN ASPCANADA, to a host behind the ASA 192.168.100.xx, I can't reach 57.5.64.250 or 251 and vice versa. But the tunnel is up. Can you help me please, thank you in advance.

  Add these two lines to the NAT 0 access list:

  inside_outbound_nat0_acl list extended access allowed hosting ASP-NETWORK 255.255.255.0 ip 57.5.64.251

  inside_outbound_nat0_acl list extended access allowed hosting ASP-NETWORK 255.255.255.0 ip 57.5.64.250

  Also make sure this reflection of these statements are also in the distance of the ASA NAT 0-list of access.

  Test and validate results

  HTH

  Sangaré

  Pls rate helpful messages

• Hello Team Support, I just update iOS to 9.3 and the active stage, then my iPad cannot reach to the apple Server (internet connection is always good in this case). Apple ID

  Hello support team,

  I just updated iOS at 9.3 and the active step then my iPad cannot reach to the apple Server (internet connection is always good in this case). Apple ID & password are still loggin in/out using the iTune software.

  @VietNam country

  See you soon,.

  Thing

  Thing,

  Try again later. Server demand is strong and it's a common problem when a new update has been released.

  

• Continually, I get the error that cannot reach the server while trying to install SP1.

  Win XP Pro reloading, get all updates

  I reinstalled Windows XP Pro and need to update to SP1 to 3 as well as all security updates.  (After download) installation, SP1, I continually get the error that cannot reach the server, visit Web of MS for a version that requires no web access if the problem persists. I can't find this version of SP1 that does not need to happen on the server from Ms.  In addition, isn't there an easier way to get all updates when you perform a new installation instead of going one by one with all the updates?

  If you have SP1A, then you can go straight to the installation of SP3.  If you have SP1, then you need to install SP1A or SP2 before going to SP3.  You can get the updates described in the following article:

  "How to obtain the latest Windows XP service pack"
    <>http://support.Microsoft.com/kb/322389/ >

  HTH,
  JW

• Get the error code: 0 x 80041003 in Event Viewer. Events cannot be delivered through this filter until the problem is resolved

  Original title: - what the heck is - this?

  Can someone tell me what this means - in English?

  Filter event with the query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace '//./root/CIMV2' because of error 0 x 80041003.» Events cannot be delivered through this filter until the problem is resolved.

  I get this topic once per hour in my diary of events 'Application '.  The Source is: Microsoft-Windows-WMI and the event number is: 10

  Every word is understandable and I know what they mean, but how they are threaded and beat me to the syntax.

  Bill

  Thanks for the reply, Gerry.  I'm no stranger to computer, having started in 1962 in the Navy for 20 years.  The HD is fine.  I used the Hitachi software testing to verify this.  RAM is also fine after running MEMTest for about 17 hours.  CHKDSK shows up at all no error.

  I agree it could be caused by a hardware fault and looking for that I ran some tension and trials of O-scope on the motherboard.  The only discrepancy I found was Aida64 Pro told me that the 3.3V rail was only 1.75 v.  My DS was told that the rail was 3.327.  This led to the conclusion that maybe the sensor was messed up.  I have an almost identical computer with a motherboard in the same series and Aida reports that rail even as 3.319v.  So, I think that the motherboard may be offset slightly.

  The re - install is an easier way to remove a large number of applications I just didn't need more and had not touched in over a year.  Revo even would have struggled to clear the registry after such massive uninstall.

  I found that the results from a command prompt is quite easy if you issue the command once, read the results on the screen, and then do it again but to redirect the output to a text file ("' do_whatever > test_output.txt '").  All you have to do is cop0y and paste a post.

  This re - install and the subsequent installation of SP2, seems to have solved the error of the event: for now.

  Bill

• Event 10, WMI and error 0 x 80041003, events cannot be delivered through this filter until the issue is resolved.

  Original title: that the error of the Devil: the 10, WMI event

  Log name: Application
  Source: Microsoft-Windows-WMI
  Date: 22/02/2013 20:23:43
  Event ID: 10
  Task category: no
  Level: error
  Keywords: Classic
  User: n/a
  Computer: INTL
  Description:
  Filter event with the query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace '//./root/CIMV2' because of error 0 x 80041003.» Events cannot be delivered through this filter until the problem is resolved.
  The event XML:
  http://schemas.Microsoft.com/win/2004/08/events/event">
   
     
      10
      0
      2
      0
      0
      0 x 80000000000000
     
      2515
     
     
      Application
      INTL
     
   
   
      ./root/CIMV2
      SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99
      0 x 80041003
   
  

  Anyone know what the h___ that's it?

  Hi Al Adams,.

  Thanks for posting your question in the Microsoft Community Forum.

  Based on the information, you receive the event 10, WMI and error 0 x 80041003 on Windows 7 computer.

  It would be useful that you can answer these questions to help you best.

  1. when exactly you receive the error messages?

  2. you remember changes to the computer before the show?

  This problem occurs if the WMI filter is accessible without the necessary permissions. To resolve this problem, refer to the article and try the steps:

  10 event ID is logged in the application log after you install Service Pack 1 for Windows 7 or Windows Server 2008 R2

  It will be useful.

  Let us know if you need help with Windows related issues. We will be happy to help you.

• Windows 7 Advisor - cannot reach the server

  I installed the Windows 7 advisor and both yesterday and today, he cannot reach the server updates - or before scanning - so it does not work for me.  Any ideas? The server is down? I can access many other things!

  It seems to run normally today.

• The local variable cannot be declared outside a function.

  I was getting an ORA-936 on an application that I support (Oracle 11 g, CF 11, Windows Server 2012).  The database went down yesterday, for some reason unknown to me, and when he came, I'm now getting this error message.  The only pointer to the .cfm file is the sponsor.  I don't see how to fix it.  Can what information I include that will help you help me?  It seems that the more I learn, something new always comes along.   Here is the error page that is displayed.  I have not changed all the statements, I know.   Thank you.

   The local variable application cannot be declared outside of a function.
  All variables defined with the var keyword must be declared inside a function.
  
  Resources:
  
      Check the ColdFusion documentation to verify that you are using the correct syntax.
      Search the Knowledge Base to find a solution to your problem.
  
  Browser       Mozilla/5.0 (Windows NT 6.1; Win64; x64; rv:46.0) Gecko/20100101 Firefox/46.0
  Remote Address       108.44.188.221
  Referrer       https://TestServer/secure/Requirement/requirementsum.cfm?frompage=orig&CFID=58847&CFTOKEN=1c45276fd65debf-7F25B5E6-AA99-1268-0B24AB3E54D73594
  Date/Time       27-May-16 01:25 PM
  Stack Trace
  
  
  coldfusion.compiler.ASTvariableDefinition$InvalidVarDefinition: The local variable application cannot be declared outside of a function.
      at coldfusion.compiler.ASTvariableDefinition.register(ASTvariableDefinition.java:98)
      at coldfusion.compiler.SemanticAnalyzer.transform(SemanticAnalyzer.java:340)
      at coldfusion.compiler.Treewalker.postorder(Treewalker.java:100)
      at coldfusion.compiler.Treewalker.postorder(Treewalker.java:27)
      at coldfusion.compiler.Treewalker.postorder(Treewalker.java:27)
      at coldfusion.compiler.NeoTranslator.parseAndTransform(NeoTranslator.java:443)
      at coldfusion.compiler.NeoTranslator.translateJava(NeoTranslator.java:370)
      at coldfusion.compiler.NeoTranslator.translateJava(NeoTranslator.java:147)
      at coldfusion.runtime.TemplateClassLoader$TemplateCache$1.fetch(TemplateClassLoader.java:436)
      at coldfusion.util.LruCache.get(LruCache.java:180)
      at coldfusion.runtime.TemplateClassLoader$TemplateCache.fetchSerial(TemplateClassLoader.java:362)
      at coldfusion.util.AbstractCache.fetch(AbstractCache.java:58)
      at coldfusion.util.SoftCache.get_statsOff(SoftCache.java:133)
      at coldfusion.util.SoftCache.get(SoftCache.java:81)
      at coldfusion.runtime.TemplateClassLoader.findClass(TemplateClassLoader.java:609)
      at coldfusion.filter.PathFilter.invoke(PathFilter.java:101)
      at coldfusion.filter.ExceptionFilter.invoke(ExceptionFilter.java:94)
      at coldfusion.filter.BrowserDebugFilter.invoke(BrowserDebugFilter.java:79)
      at coldfusion.filter.ClientScopePersistenceFilter.invoke(ClientScopePersistenceFilter.java:28)
      at coldfusion.filter.BrowserFilter.invoke(BrowserFilter.java:38)
      at coldfusion.filter.NoCacheFilter.invoke(NoCacheFilter.java:58)
      at coldfusion.filter.GlobalsFilter.invoke(GlobalsFilter.java:38)
      at coldfusion.filter.DatasourceFilter.invoke(DatasourceFilter.java:22)
      at coldfusion.filter.CachingFilter.invoke(CachingFilter.java:62)
      at coldfusion.CfmServlet.service(CfmServlet.java:219)
      at coldfusion.bootstrap.BootstrapServlet.service(BootstrapServlet.java:89)
      at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:303)
      at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:208)
      at coldfusion.monitor.event.MonitoringServletFilter.doFilter(MonitoringServletFilter.java:42)
      at coldfusion.bootstrap.BootstrapFilter.doFilter(BootstrapFilter.java:46)
      at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:241)
      at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:208)
      at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:220)
      at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:122)
      at org.apache.catalina.authenticator.AuthenticatorBase.invoke(AuthenticatorBase.java:505)
      at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:170)
      at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:103)
      at org.apache.catalina.valves.AccessLogValve.invoke(AccessLogValve.java:956)
      at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:116)
      at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:437)
      at org.apache.coyote.ajp.AjpProcessor.process(AjpProcessor.java:197)
      at org.apache.coyote.AbstractProtocol$AbstractConnectionHandler.process(AbstractProtocol.java:625)
      at org.apache.tomcat.util.net.JIoEndpoint$SocketProcessor.run(JIoEndpoint.java:316)
      at java.util.concurrent.ThreadPoolExecutor.runWorker(ThreadPoolExecutor.java:1145)
      at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:615)
      at org.apache.tomcat.util.threads.TaskThread$WrappingRunnable.run(TaskThread.java:61)
      at java.lang.Thread.run(Thread.java:722)
  

  I had added end brand to all the and it has cleared up.  Weird.

  Which brings me to another question.  When you do make the end like this tag or use the tag?

• Cannot add host ESXi 5.5 to vCenter for a routed network - cannot communicate with the specified host

  I was wondering if anyone has come across this problem before, who could give advice how to fix them:

  Host of pre-production UCS ESXi migration of a Production vCenter on another network (routing in place)

  Can ping both directions successfully - from vCenter Prod to the host of the pre-production

  no firewall between the two.

  902 port is open on the host

  Host connects to the pre-production vCenter on the subnet even fine

  VCenter production can add different hosts on the same network end

  Even with the various guests of ESXi UCS.

  ESXi host was completely disconnected and removed from vCenter inherited before attempting to add. No dvswitch physical or virtual.

  Then try and add, enter the user name and password and get cannot communicate with the specified host.

  Thank you

  The solution to this. Used ESX host 5.5 3B (3248547) update that disables SSLv3. (Ref: VMware ESXi 5.5 updated Notes version 3B) one of the consequences of this is that older versions of vCenter (such as trying to move the host) can not add/connect host.

  Enable SSLv3 to spend (port 443) on the resolved host (virtuallyPeculiar: connection A ESXi 5.5 U3b host to vCenter with a lower Version A.)

  Note: should not enable SSLv3 to Port 902.

  Ref:

  The SSLv3 Protocol on vSphere 5.x configuration (2139396) | VMware KB

  Many thanks to Suhas Savkoor of virtuallyPeculiar for resolution for this on his website display

• HP MSA2324i, new volume / LUN added, cannot be seen by the host ESX 4.1 (fine old LUN work)

  Hello

  I have a vSphere Essentials Plus 4.1 cluster that is connected to 2 x bays HP MSA2324i SAN, we have 2 x hosts and both can see current volumes / LUNS absolutely perfect (vMotion and migration of VM offline all work as expected). I'm starting a consolidation project virtual disks / volume of the San 2 x, however a new volume I created on a network SAN cannot be seen by the other host.

  The new volume has been implemented exactly like the others, but of course with a unique logic for mapping unit number explicit, but when scanning the iSCSI HBA the new LUN is never found :-(

  I was wondering if others have had also this happens to them and know why this may be implemented?.

  (This is a company that I joined, it's my third week, and that they had also no VMware subscription on their reunification since 2012, otherwise I would be to connect a call to technical support of VMware, by train to get the sub upwards and running)

  OK I think that might be the cause, I came across this recently maximum LUN ID is 255, change the logic unit to a number smaller than 255 ID number and try again, let us know how you go!

  vM

  -----------------------

  VCAP-DCD / VCAP-DCA / VCP-CLOUD / VCP - DT / VCP5 / VCP4

  -----------------------

  vMustard.com

• The host cannot be admitted to the current cluster Enhanced vMotion compatibility mode.

  Hello everyone

  Here's the situation...

  I have:

  vSphere 5.1 Cluster with two 5.1 ESXi hosts and configuration VSA.

  vCenter Server running on a virtual Windows Server 2012 machine.

  Task: Transfer virtual vCenter to a physical machine.

  I have install the physical machine with Windows server 2012.

  Installed vCenter 5.5 (hosts Newer then the ESXi 5.1)

  VSA installed Manager (VSA Cluster 5.5)

  When go to VSA Manager I am introduced to the following screen...

  

  Recover DOES NOT work!

  Full move operation DOES NOT work!

  It recognizes the Cluster AUV-> check availability (is online and OK)-> begins to create the Cluster VSA and it fails with the following error...

  Move the cluster host

  VSA HA Cluster

  The host cannot be admitted to the current cluster Enhanced vMotion compatibility mode. Under voltage or suspension of the virtual machines on the host can use the CPU features hidden by this mode.

  Could someone please help?

  Thanks to you all! This problem has been SOLVED as follows...

  • VCenter Server go to--> "C:\Program Files\VMware\Infrastructure\tomcat\webapps\VSAManager\WEB-INF\classes".
  • Open the file "dev.properties" with Notepad
  • Change the line that says "evc.config.baseline = lowest" to 'highest = evc.config.baseline' and save the file.
  • Perform the SERVICES. MSC and reboot 'VMware VirtualCenter Management Webservices'

  After that it of back in the VSA Manager and run it again 'Cluster of VSA recover'!

  Now, the wizard should be able to add hosts to the inventory, create the HA Cluster and add hosts to the HA cluster and configure Cluster HA.

  Done everything! :-)

• Urgent issue: remote vpn users cannot reach server dmz

  Hi all

  I have an asa5510 firewall in which remote vpn client users can connect but they cannot ping or access the dmz (192.168.3.5) Server

  They also can't ping the out interface (192.168.2.10), below is the show run, please help.

  SH run

  ASA5510 (config) # sh run
  : Saved
  :
  : Serial number: JMX1243L2BE
  : Material: ASA5510, 256 MB RAM, Pentium 4 Celeron 1599 MHz processor
  :
  ASA 5,0000 Version 55
  !
  Majed hostname
  activate the encrypted password of UFWSxxKWdnx8am8f
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  DNS-guard
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 192.168.2.10 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  192.168.1.10 IP address 255.255.255.0
  !
  interface Ethernet0/2
  nameif servers
  security-level 90
  192.168.3.10 IP address 255.255.255.0
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  boot system Disk0: / asa825-55 - k8.bin
  passive FTP mode
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  acl_outside to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
  acl_outside list extended access allow icmp 192.168.5.0 255.255.255.0 192.168.1.0 255.255.255.0
  acl_outside of access allowed any ip an extended list
  acl_outside list extended access permit icmp any one
  acl_inside list extended access allowed host ip 192.168.1.150 192.168.5.0 255.255.255.0
  acl_inside list extended access allowed host icmp 192.168.1.150 192.168.5.0 255.255.255.0
  acl_inside list extended access allowed host ip 192.168.1.200 192.168.5.0 255.255.255.0
  acl_inside list extended access allowed host icmp 192.168.1.200 192.168.5.0 255.255.255.0
  acl_inside list extended access allowed host ip 192.168.1.13 192.168.5.0 255.255.255.0
  acl_inside list extended access allowed host icmp 192.168.1.13 192.168.5.0 255.255.255.0
  acl_inside to access ip 192.168.1.0 scope list allow 255.255.255.0 host 192.168.3.5
  acl_inside list extended access allow icmp 192.168.1.0 255.255.255.0 host 192.168.3.5
  acl_inside list extended access deny ip 192.168.1.0 255.255.255.0 192.168.5.0 255.255.255.0
  acl_inside list extended access deny icmp 192.168.1.0 255.255.255.0 192.168.5.0 255.255.255.0
  acl_inside of access allowed any ip an extended list
  acl_inside list extended access permit icmp any one
  acl_server of access allowed any ip an extended list
  acl_server list extended access permit icmp any one
  Local_LAN_Access list standard access allowed 10.0.0.0 255.0.0.0
  Local_LAN_Access list standard access allowed 172.16.0.0 255.240.0.0
  Local_LAN_Access list standard access allowed 192.168.0.0 255.255.0.0
  access-list nat0 extended ip 192.168.0.0 allow 255.255.0.0 192.168.0.0 255.255.0.0
  allow acl_servers to access extensive ip list a whole
  acl_servers list extended access allow icmp a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 servers
  IP local pool 192.168.5.1 - 192.168.5.100 mask 255.255.255.0 vpnpool
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 621.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  interface of global (servers) 1
  NAT (inside) 0 access-list nat0
  NAT (inside) 1 192.168.1.4 255.255.255.255
  NAT (inside) 1 192.168.1.9 255.255.255.255
  NAT (inside) 1 192.168.1.27 255.255.255.255
  NAT (inside) 1 192.168.1.56 255.255.255.255
  NAT (inside) 1 192.168.1.150 255.255.255.255
  NAT (inside) 1 192.168.1.200 255.255.255.255
  NAT (inside) 1 192.168.2.5 255.255.255.255
  NAT (inside) 1 192.168.1.0 255.255.255.0
  NAT (inside) 1 192.168.1.96 192.168.1.96
  NAT (servers) - access list 0 nat0
  NAT (servers) 1 192.168.3.5 255.255.255.255
  static (inside, servers) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
  static (servers, inside) 192.168.3.5 192.168.3.5 netmask 255.255.255.255
  Access-group acl_outside in interface outside
  Access-group acl_servers in the servers of the interface
  Route outside 0.0.0.0 0.0.0.0 192.168.2.15 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.3.5 255.255.255.255 servers
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic outside_dyn_map 10 the value transform-set ESP-3DES-SHA
  Crypto-map dynamic outside_dyn_map 10 set security-association life seconds288000
  Crypto-map dynamic outside_dyn_map 10 kilobytes of life together - the association of safety 4608000
  Crypto-map dynamic outside_dyn_map 10 the value reverse-road
  map Outside_map 10-isakmp ipsec crypto dynamic outside_dyn_map
  Outside_map interface card crypto outside
  ISAKMP crypto identity hostname
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  No encryption isakmp nat-traversal
  Telnet 192.168.2.0 255.255.255.0 outside
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet 192.168.3.0 255.255.255.0 servers
  Telnet 192.168.38.0 255.255.255.0 servers
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal vpn group policy
  attributes of vpn group policy
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Local_LAN_Access
  allow to NEM
  password encrypted qaedah Ipsf4W9G6cGueuSu user name
  password encrypted moneef FLlCyoJakDnWMxSQ user name
  chayma X7ESmrqNBIo5eQO9 username encrypted password
  sanaa2 zHa8FdVVTkIgfomY encrypted password username
  sanaa x5fVXsDxboIhq68A encrypted password username
  sanaa1 x5fVXsDxboIhq68A encrypted password username
  bajel encrypted DygNLmMkXoZQ3.DX privilege 15 password username
  daris BgGTY7d1Rfi8P2zH username encrypted password
  taiz Ip3HNgc.pYhYGaQT username encrypted password
  damt gz1OUfAq9Ro2NJoR encrypted privilege 15 password username
  aden MDmCEhcRe64OxrQv username encrypted password
  username hodaidah encrypted password of IYcjP/rqPitKHgyc
  username yareem encrypted password ctC9wXl2EwdhH2XY
  AMMD ZwYsE3.Hs2/vAChB username encrypted password
  haja Q25wF61GjmyJRkjS username encrypted password
  cisco 3USUcOPFUiMCO4Jk encrypted password username
  ibbmr CNnADp0CvQzcjBY5 username encrypted password
  IBBR oJNIDNCT0fBV3OSi encrypted password username
  ibbr 2Mx3uA4acAbE8UOp encrypted password username
  ibbr1 wiq4lRSHUb3geBaN encrypted password username
  password username: TORBA C0eUqr.qWxsD5WNj encrypted
  username, password shibam xJaTjWRZyXM34ou. encrypted
  ibbreef 2Mx3uA4acAbE8UOp encrypted password username
  username torbah encrypted password r3IGnotSy1cddNer
  thamar 1JatoqUxf3q9ivcu encrypted password username
  dhamar pJdo55.oSunKSvIO encrypted password username
  main jsQQRH/5GU772TkF encrypted password username
  main1 ef7y88xzPo6o9m1E encrypted password username
  password username Moussa encrypted OYXnAYHuV80bB0TH
  majed 7I3uhzgJNvIwi2qS encrypted password username
  lahj qOAZDON5RwD6GbnI encrypted password username
  vpn tunnel-group type remote access
  VPN tunnel-group general attributes
  address vpnpool pool
  Group Policy - by default-vpn
  Tunnel vpn ipsec-attributes group
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !

  Hello brother Mohammed.

  "my asa5510 to work easy as Server & client vpn at the same time.?

  Yes, it can work as a client and a server at the same time.

  I have never seen anyone do it but many years of my understanding, I have no reason to think why it may be because the two configurations (client/server) are independent of each other.

  Your ASA function as server uses the "DefaultL2LGroup" or it uses standard group policy and tunnel-group are mapped to the remote clients ASA?

  Thank you

• Acrobat XI cannot reach activation server after update

  XI Acrobat bought for my wife (this is the version that she needs) a few weeks ago.  Did a clean install on a new machine and activated correctly, no problem.  It worked exactly as it should.

  Tonight, she did something really terrible, she agreed to do an update.  At the end there, impossible to reach the Adobe server to activate.

  Troubleshooting, it seems that it cannot reach the Adobe server.  I tried on my machine and I could not reach him; she refuses connections.

  Is this intentional, a way to kill older versions of Acrobat?  She cannot use the newest one, he must be pro XI.  The server still exists?

  Does anyone know a workaround that will repair Acrobat XI on his machine?  Should I delete everything and reinstall from the original CD?  And tell him to NEVER accept "updates?

  I discovered the problem.

  I am the victim of a fraud, the software I bought is fake.  It was a bit

  develop, in that the installation process creates a hosts file which blocked

  all access to any Adobe authentication server address.  Apparently the fake

  Serial number fooled the program itself, but it cannot validate at Adobe.  When my

  wife did the update, for some reason, he attempted to validate again and this is where

  He failed.  I do not know if he would have continued working if she had not

  the upgrade, but I always discourage updates that many end up breaking

  something.  Yes, I know the security implications, but I had two

  orders of magnitude more broken with updates that the security problems if

  will try my luck.

  Now, I'm the money I spent, but since (for compatibility reasons) my wife

  needs XI pro, which is not sold by Adobe, I have little chance.  I have

  don't want a pirated version but, apparently, selling online, at least on ebay, can

  trust.  Techsoft24 in London seems legitimate and I can try it, unless someone

  can suggest a better way to buy a package of Acrobat Pro XI legitimate known.

  Peter

• Cannot add appointments to the calendar

  I used OS10.6.8 until recently, but the new Macbook Pro has OS 10.11.6

  I tried to use the calendar in ElCaptain for the first time, but failed to add all appointments.

  When I tried to make a message entry; "You can change events in the calendar 'Found in the Mail'."

  Only the calendar administrator and delegates with permission can make changes to the read-only calendars. To make changes to the calendar, contact the calendar administrator.

  I found the following tips, but that did not work:

  • Select the item, and then choose file > get info, or press on command I.
  • Click the triangle next to sharing and permissions to expand the section.
  • Click on the drop down menu next to your user name to view the settings for permissions.
  • If you are not signed in as an administrator, you may need to click the lock icon and enter an administrator name and password.
  • Change the permissions to read & write or "read only".

  I selected calendar in applications and followed the instructions above.

  Everyone is set to "Custom".

  System has been on "read and write".

  Wheel has been set to "read only".

  Everyone has been set to "" read-only ".

  With the "padlock icon" open I tried to change the entries:

  By system logic should have allowed me to make entries in the calendar. However, I tried to affect the other classifications "read and write.

  The result was a warning message: "the operation cannot be performed because you don't have the necessary authorization."

  I check accounts and not use their calendar, so I am at a loss.

  My previous systems never had problems with calendar, or change permissions.

  Any ideas would be welcome.

  Hi memory,

  Congratulations on the new MacBook Pro! I appreciate that you try add calendar events, but to send a message that you cannot write to this calendar. I know it's important to keep track of your events, so I am happy to help clarify this.

  Due to the error "you cannot change events in the calendar 'Found in the Mail'." he said that you currently selected found in Mail schedule, which does not allow to write for her because these events are created only from your Mail.

  To change the calendar you are trying to create these events in, first, click on the Calendar button in the upper left corner of the window, and then select the new calendar.

  If you do not have other calendars or need to create a new one, check out the following steps:

  The basics of the Mac: calendar keeps your appointments - Apple Support

  Create new calendars

  By default, OS X includes two calendars in Calendar - work and home. If you want to create a new calendar, choose new calendar in the menu file . In the text box, type a name for your calendar. For example, if you have children, you can create a separate calendar for each of them follow their schedules. You can see and control how your calendars will appear by clicking the calendar button.

  

  To change the color or the name of a calendar, select it in the calendars list, and then choose the command Edition > read the information. To remove a calendar and all its manifestations, click or control the calendar name, and then select delete in the context menu that appears.

  Once you have selected a different calendar, you can add events as expected:

  Calendar (El Capitan): Add, edit, or delete events

  Thank you for using communities of Apple Support, cheers!

• the camera shutter sound cannot be silent with the mute button on my phone i 6 s

  the camera shutter sound cannot be silent with the mute button on my phone i 6 s

  Depending on where you purchased your phone, this is not possible, because of legislation in these countries that regulate this feature.

  In all other cases, try to force reboot the phone by holding down the button sleep and home for 10 seconds, until the Apple logo comes back again. You won't lose data, but it can cure some problems after installing new software or applications.

  In the case where this does not work, restore the phone:

  Use iTunes to restore your device iOS to factory settings