Activate the Transparent Tunneling on the VPN client?

Similar Questions

• How to install the VPN Client and the tunnel from site to site on Cisco 831

  How can I configure a Cisco 831 router (Branch Office) so that it will accept incoming VPN Client connections and initiate tunneling IPSec site to site on our hub site that uses a VPN 3005 concentrator?  I could get the tunnel to work by configuring it in a dynamic encryption card, but interesting traffic side Cisco 831 would not bring the tunnel upward.  I could only put on the side of the hub.  If I use a static encryption card and apply it to the external interface of the 831 I can get this working but then I couldn't get the VPN Client to work.

  Thank you.

  The dynamic map is called clientmap
  The static map is called mymap

  You should have:

  no card crypto not outmap 10-isakmp ipsec dynamic dynmap
  map mymap 10-isakmp ipsec crypto dynamic clientmap

  interface Ethernet1
  crypto mymap map

  Federico.

• The VPN Clients cannot Ping hosts

  I'll include a post my config. I have clients that connect through the VPN tunnel on the 180.0.0.0/24 network, 192.168.1.0/24 is the main network for the office.

  I can connect to the VPN, and I received a correct address assignment. I belive tunneling can be configured correctly in the aspect that I can always connect to the internet then on the VPN, but I can't ping all hosts on the 192.168.1.0 network. In the journal of the ASDM debugging, I see pings to the ASA, but no response is received on the client.

  6

  February 21, 2013

  21:54:26

  180.0.0.1

  53508

  192.168.1.1

  0

  Built of ICMP incoming connections for faddr gaddr laddr 192.168.1.1/0 (christopher) 192.168.1.1/0 180.0.0.1/53508

  Any help would be greatly appreciated, I'm currently presuring my CCNP so I would get a deeper understanding of how to resolve these issues.

  -Chris

  hostname RegencyRE - ASA

  domain regencyrealestate.info

  activate 2/VA7dRFkv6fjd1X of encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  name 180.0.0.0 Regency

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  link to the description of REGENCYSERVER

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  link to the description of RegencyRE-AP

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.1.120 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.248

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 208.67.220.220

  name-server 208.67.222.222

  domain regencyrealestate.info

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 Regency 255.255.255.224

  RegencyRE_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

  outside_access_in list extended access permit icmp any one

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  mask Regency 180.0.0.1 - 180.0.0.20 255.255.255.0 IP local pool

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  ASDM 255.255.255.0 inside Regency location

  ASDM location 192.168.0.0 255.255.0.0 inside

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 12.186.110.2 1

  Route inside 192.0.0.0 255.0.0.0 192.168.1.102 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  LOCAL AAA authentication serial console

  http server enable 8443

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 15

  SSH version 2

  Console timeout 0

  dhcprelay Server 192.168.1.102 inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  NTP server 69.25.96.13 prefer external source

  NTP server 216.171.124.36 prefer external source

  WebVPN

  internal RegencyRE group strategy

  attributes of Group Policy RegencyRE

  value of server DNS 208.67.220.220 208.67.222.222

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list RegencyRE_splitTunnelAcl

  username password encrypted adriana privilege 0

  christopher encrypted privilege 15 password username

  irene encrypted password privilege 0 username

  type tunnel-group RegencyRE remote access

  attributes global-tunnel-group RegencyRE

  Regency address pool

  Group Policy - by default-RegencyRE

  IPSec-attributes tunnel-group RegencyRE

  pre-shared key R3 & eNcY1.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:35bc3a41701f7f8e9dde5fa35532896d

  : end

  Hello

  -be sure that the destination host 192.168.1.x has a route towards 180.0.0.0 by the ASA gateway.

  -Configure the following figure:

  capture capin interface inside match icmp 192.168.1.x host 180.0.0.x

  capture ASP asp type - drop all

  then make a continuous ping and get 'show capin cap' and 'asp cap.

  -then check the ping, the 'encrypted' counter is increasing in the VPN client statistics

  I would like to know about it, hope this helps

  ----

  Mashal

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• The VPN client VPN connection behind other PIX PIX

  I have the following problem:

  I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

  So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

  I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

  Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

  If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

  305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

  194.x.x.x is our customer s address IP PIX

  I understand that somewhere access list is missing, but I can not understand.

  Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

  Can you please help me?

  Thank you in advan

  The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

  I've cut and pasted here for you to read, I think that the problem mentioned below:

  Question:

  Hi Glenn,.

  Following is possible?

  I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

  The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

  My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

  Thank you very much for any help provided in advance.

  Response from Glenn:

  First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

  fixup protocol esp-ike

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

  If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

  ISAKMP nat-traversal

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

  NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

  ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

  A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

  NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

  Hope that helps.

• The VPN client connection

  Is it possible to configure the VPN client to set up some sort of login and password so when you run, connects automatically without writing the user name and password.

  This must be the vpn client without making any changes on the vpn server.

  No idea how to do this?

  Kind regards

  to 4.0.2 4.6 & 4.8 Yes - in the profile .pcf file, make sure that

  SaveUserPassword = 1

  This will keep the user name & password in the profile, when you click on it - it should fine connection.

  You must also activate the user store password: -.

  In the pix / asa - under the client VPN profile:-

  allow password-storage

  HTH.

• Itineraries other nets will be lost when using the vpn client?

  I have a very general question. I intend to implement a security solution for the extranet partners to connect to our intranet using VPN client. IPSec will close on the external interface of the Cisco PIX firewall v6.3.

  Now, my consirn is, I downloaded the vpn client to test but I saw no advance settings to define what network traffic will pass through the IPSec tunnel and which will be routed normally. Is it by default all traffic passing through VPN? Is that what it means if there are other networks using their default route, they will not be able to achieve? (i.e. the Internet).

  Thank you.

  That would depend on how you set up the PIX. You can allow the VPN to your site and access to the Internet at the same time. This is called the split tunneling. It is configurable on the PIX, not the customer.

  This link might help you get started, but I'm sure that there stronger links.

  http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/products_command_reference_chapter09186a00800ec9ec.html

• IP address connection sets using the VPN Client

  Hello world. I'm using a VPN Client when I establish a VPN Tunnel with a 1600 router, and I have a question.

  Can I assign a fixed IP address in the client, instead the router send to random addresses from customer?

  What I would he do this?

  It would be in the configuration of the VPN client, or in the configuration of the router?

  If so, I'm doing this?

  Do I need another tool, or other software or hardware to do?

  any help is hope...

  Thank you...

  Hello

  I don't think that there is a simple way to do this.

  However, if you create a different groupname for the user who needs a static IP address, I think you should be good to go

  So what you need to do, create a new pool of addresses. Make the start and end ip address be the same (this is the address to which you want to assign to the VPN user)

  Configure another ipsec on the router group and bind the new pool to this group

  Ask your VPN client to connect to this group

  Hope that helps

  Jean Marc

• The VPN Clients need access to the subnet on another router

  Hello

  We have a pix 515e PIX Version 8.0 (2)

  We have two subnet 10.1.x.x/16 and 10.2.x.x/16

  The firewall is on 10.1.x.x and vpn clients can access this subnet.

  The firewall can ping 10.2.x.y where x is a server in the other subnet.

  On the 10.2.x.x customers out the firewall.

  The problem is that vpn clients cannot access the server of 10.2.x.y even if the pix can ping 10.2.x.y and the road for him.

  What I need to check that the vpn rules are correct in the pix 515e?

  I think it is a rule of exemption nat or something like that not exactly sure.

  Everything would be a great help.

  Thank you

  Hello

  For clients VPN access to these subnets, check the following:

  1 NAT exemption include these subnets (if not using NAT)... it's the NAT0 ACL command

  2. these subnets is included in the split tunneling

  3. these subnets have a route to the PIX to send traffic to the VPN client pool.

  4. There are no ACLs not applied to the inside interface of the PIX deny this communication.

  Federico.

• ASA problem inside the VPN client routing

  Hello

  I have a problem where I can't reach the VPN clients with their vpn IP pool from the inside or the asa itself. Connect VPN clients can access internal network very well. I have no nat configured for the pool of vpn and packet trace crypt packages and puts it into the tunnel. I'm not sure what's wrong.

  Here are a few relevant config:

  network object obj - 192.168.245.0

  192.168.245.0 subnet 255.255.255.0

  192.168.245.1 - 192.168.245.50 vpn IP local pool

  NAT (inside, outside) static source any any destination static obj - 192.168.245.0 obj - 192.168.245.0 no-proxy-arp-search to itinerary

  Out of Packet trace:

  Firewall # entry packet - trace inside the x.x.x.x icmp 8 0 192.168.245.33

  Phase: 1

  Type: ACCESS-LIST

  Subtype:

  Result: ALLOW

  Config:

  Implicit rule

  Additional information:

  MAC access list

  Phase: 2

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  in 192.168.245.33 255.255.255.255 outside

  Phase: 3

  Type: ACCESS-LIST

  Subtype: Journal

  Result: ALLOW

  Config:

  Access-group acl-Interior interface inside

  access list acl-Interior extended icmp permitted an echo

  Additional information:

  Phase: 4

  Type: IP-OPTIONS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Phase: 5

  Type: INSPECT

  Subtype: np - inspect

  Result: ALLOW

  Config:

  Additional information:

  Phase: 6

  Type:

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Phase: 7

  Type: NAT

  Subtype:

  Result: ALLOW

  Config:

  NAT (inside, outside) static source any any destination static obj - 192.168.245.0

  obj - 192.168.245.0 no-proxy-arp-search to itinerary

  Additional information:

  Definition of static 0/x.x.x.x-x.x.x.x/0

  Phase: 8

  Type: VPN

  Subtype: encrypt

  Result: ALLOW

  Config:

  Additional information:

  Phase: 9

  Type: CREATING STREAMS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  New workflow created with the 277723432 id, package sent to the next module

  Result:

  input interface: inside

  entry status: to the top

  entry-line-status: to the top

  output interface: outside

  the status of the output: to the top

  output-line-status: to the top

  Action: allow

  There is no route to the address pool of vpn. Maybe that's the problem? I don't know than that used to work before we went to 8.4.

  Check if the firewall is enabled on your host from the client ravpn and blocking your pings.

• Need a guide to configure the VPN Client

  Hello...

  I vpn in my 506th pix and I have ver.4.0.1 software vpn client installed on the other pc (on the outside). In the firewall, there are two types of vpn; VPN site to site and remote vpn access. We use vpn for remote access to allow the vpn client to access our server right?

  This is all new to me and could you give an example how to configure vpn inside my firewall in CLI or PDM command and how to configure the software vpn client.

  Please help us beginners cisco

  Tonny

  Tony,

  Try chanigng a cisco and see if it solves... but otherwise, since you changed the PIX outside IP now, you will be able to make VPN connections to the new public IP address now, if it is routed on the internet.

  can you please try to connect now and let us know what is happening?

• The Vpn Client ASDM download

  I was trying to the vpn Wizard ASDM allows you to download the new client anyconnect 4.2 and I got errors saying that the file is not valid.

  Should which file I download in order for customers to download the vpn client.

  I have asa x 5506

  Hello

  You must use the anyconnect file you get from cisco.com or Cisco partner and download, the .pkg file extension

  for example:

  # poster run | grep anyconnect
  AnyConnect image disk0:/anyconnect-win-4.2.01022-k9.pkg 1

  HTH

  Samer.

• Is there a 64-bit version of the VPN Client for the coming of Vista?

  Is there a 64-bit version of the VPN Client for Vista to come for VPN 3000 series concentrators?

  Hello

  A bit is a tour here.

  According to Cisco:

  Install the VPN Client on a Vista 64 bit Machine will cause an error 1721

  Cisco IPSec Client does not support 64-bit. If the user requires a 64-bit support, upgrade path is to use the Cisco AnyConnect VPN Client instead, that supports 64-bit. Note that the AnyConnect Client supports only SSL VPN (CSCsi26069) connections.

  So if you want to go with 64-bit, you need SSL support on the VPN 3000 series and replace all IPSEC with SSL connections.

  Please rate if this helped.

  Kind regards

  Daniel

• Unable to access the VPN Client LAN

  I configured a 877 for VPN Client Access. The Client authenticates and connects and receives an IP address off the coast of the pool of intellectual property. However, he is unable to access anything on the IP network.

  I have included my router config. The VPN Client is v5.0.05.0290.

  Any ideas on what I'm missing?

  Can try reverse our ACL VPN-Client, I think that it is written in the wrong way

  For example:

  VPN-Client extended IP access list

  Note * permit VPN Client pool *.

  IP enable any 192.168.201.0 0.0.0.255

  or more precise

  VPN-Client extended IP access list

  Note * permit VPN Client pool *.

  192.168.1.0 255.255.255.0 ip permit 192.168.201.0 0.0.0.255

• The VPN client user authentication

  When users connect to our network remotely via VPN user name field is already filled with the last person who logged. I know that they just delete the username and enter their own, but is there a way the client can be configured to where the username field will be always empty for all those who want access to the network via VPN? We have an ASA 5510 with version 7.0 (8) and a windows 2003 with IAS server for windows authentication. Thank you!

  Hello

  In FCP, you can configure a single line is not editable by the user (or the vpn client).

  Simply insert an attack! Like this

  ! Username =

  ! SaveUserPassword = 0

  ! UserPassword =

  ! enc_UserPassword =

  Subsequently the vpn client will not save registrations for these settings more.

• field of the authentication of the vpn client

  Hi, I would like to remove the domain in the authentication of the vpn client. How?

  Could the password-management, command force the presence of the domain?

  Thank you

  Yes, once you add password management, domain field appears. If you do not need password management, you could remove it and field will disappear.