Adding more than 1 point margin to #content everything makes you invisible.

Similar Questions

• The sony handycam dcr-hc30 can endure more than the 512 MB original memory? Thank you.

  The sony handycam dcr-hc30 can endure more than the 512 MB original memory? Thank you.

  According to this table of compatibility: http://esupport.sony.com/perl/support-info.pl?&info_id=11 DCR-HC30 may use the following maps:

  Memory Stick Duo Pro - 1 GB, 2 GB and 4 GB

  Mark 2 Memory Stick Duo Pro - 1 GB, 2 GB and 4 GB.

  You can read the table to make sure I was reading it correctly.

• How to export more than 100 points of waveform to Excel

  Hello world. Novice here.

  I am sure other people have my problem, but I don't know how the word it... and impossible to find a solution for it. Maybe I don't understand Labview enough to know what is happening.

  Here's what I do: I have a waveform, and I try to save the data in the worksheet.

  Problem: the CAP is on plots of 100 data (only what is shown on the chart). In other words, I get only the data for the chart hold right now.

  Here: I want more than that - EVERYTHING. If it starts from 0 to 50 years old, I want that all the points (increments of 10 ms, which is already done) on the excel file.

  Can you guys help me? How suck this story on the graph?

  I've attached my labview (a really simple) file, so you guys know where I am.

  Thank you guys!

  I probably go this route and use import TDMS Excel add-on

  

• PlotYAppend to draw more than 1000 points

  Dear all

  When I tried to add more than 1,000 points for a WaveformPlot on a WaveformGraph, only the last 1000 points were plotted on the graph.

  Take into account that I use the method "PlotYAppend" to add points to the plot.

  Please advice because we want to increase the number of points to exceed 1000 points

  Best regards

  Mohammed,

  One of the properties of the wave shape curve is the ability of the story. The default value is 1000, you resize it to a higher value?

• Using more than 2 points of control in Interpolater.Spline

  Hello
  
  what I'm getting is a bouncing ball, I thought it could work controlling the interpolator to create a control of several points using the spline. (a feature of x ^ n ^, where n is the number of control points)
  In a Groove I can use only two control points, is there a way to use more than that, or do I have to use another way.
  
  Thanks for any help.
  
  Edited by: A.m.z on 9 may 2013 01:49
  
  Edited by: A.m.z on 9 may 2013 01:49

  Well, I guess it was not so difficult - at least when there are libraries written by others to borrow to...

  The interpolator requires the apache commons math 3.2 lib - you can download Commons-math3 - 3.2 - upload - the here:
  http://Commons.Apache.org/proper/Commons-math/download_math.cgi
  Remove Commons-math3 - 3.2.jar since the zip and put it on your class path.

  The interpolator differs slightly from the interpolator of Interpolator.SPLINE that comes with JavaFX.
  Instead of control points which bend the curve but do not lie on the curve, the interpolator takes a set of points and trace a straight regression line through the points.

  import javafx.animation.Interpolator;
  import org.apache.commons.math3.analysis.interpolation.SplineInterpolator;
  import org.apache.commons.math3.analysis.polynomials.PolynomialSplineFunction;
  
  public class BestFitSplineInterpolator extends Interpolator {
  
    final PolynomialSplineFunction f;
  
    BestFitSplineInterpolator(double[] x, double[] y) {
      f = new SplineInterpolator().interpolate(x, y);
    }
  
    @Override protected double curve(double t) {
      return f.value(t);
    }
  }
  

  Here is a usage example:

  import javafx.animation.*;
  import javafx.application.Application;
  import javafx.scene.* ;
  import javafx.scene.paint.*;
  import javafx.scene.shape.*;
  import javafx.stage.Stage;
  import javafx.util.Duration;
  
  public class BestFitSplineDemo extends Application {
  
    private static final Duration CYCLE_TIME = Duration.seconds(7);
  
    private static final int PLOT_SIZE = 500;
    private static final int N_SEGS    = PLOT_SIZE / 10;
  
    public void start(Stage stage) {
      Path path = new Path();
      path.setStroke(Color.DARKGREEN);
  
      final Interpolator pathInterpolator = new BestFitSplineInterpolator(
        new double[] { 0.0, 0.25, 0.5, 0.75, 1.0 },
        new double[] { 0.0, 0.5,  0.3, 0.8,  0.0 }
      );
  
      // interpolated spline function plot.
      plotSpline(path, pathInterpolator, true);
  
      // animated dot moving along the plot according to a distance over time function.
      final Interpolator timeVsDistanceInterpolator = new BestFitSplineInterpolator(
          new double[] { 0.0, 0.25, 0.5, 0.75, 1.0 },
          new double[] { 0.0, 0.1,  0.4, 0.85, 1.0 }
      );
  
      Circle dot = new Circle(5, Color.GREENYELLOW);
      PathTransition transition = new PathTransition(CYCLE_TIME, path, dot);
      transition.setInterpolator(timeVsDistanceInterpolator);
      transition.setAutoReverse(true);
      transition.setCycleCount(PathTransition.INDEFINITE);
      transition.play();
  
      // show a light grey path representing the distance over time.
      Path timeVsDistancePath = new Path();
      timeVsDistancePath.setStroke(Color.DIMGRAY.darker());
      timeVsDistancePath.getStrokeDashArray().setAll(15d, 10d, 5d, 10d);
      plotSpline(timeVsDistancePath, timeVsDistanceInterpolator, true);
  
      stage.setScene(
        new Scene(
          new Group(
            timeVsDistancePath,
            path,
            dot
          ),
          Color.rgb(35,39,50)
        )
      );
      stage.show();
    }
  
    // plots an interpolated curve in segments along a path
    // if invert is true then y=0 will be in the bottom left, otherwise it is in the top right
    private void plotSpline(Path path, Interpolator pathInterpolator, boolean invert) {
      final double y0 = pathInterpolator.interpolate(0, PLOT_SIZE, 0);
      path.getElements().addAll(
        new MoveTo(0, invert ? PLOT_SIZE - y0 : y0)
      );
  
      for (int i = 0; i < N_SEGS; i++) {
        final double frac = (i + 1.0) / N_SEGS;
        final double x = frac * PLOT_SIZE;
        final double y = pathInterpolator.interpolate(0, PLOT_SIZE, frac);
        path.getElements().add(new LineTo(x, invert ? PLOT_SIZE - y : y));
      }
    }
  
    public static void main(String[] args) { launch(args); }
  }
  

  Published by: jsmith on 11 may 2013 05:58

• Adding more than 4 GB of RAM to a VM Server 2008 32-bit

  Hi, can you tell me if it is possible for a Server 2008 Standard 32-bit VM for more than 4 GB of RAM? I activated the EAP, but it made no difference. Is there something specific that needs to be done as is a virtual machine?

  This is a Limitation of Windows

  Even with active EAP 4 GB maximum on 32 bits, see insert from the link:

  http://msdn.Microsoft.com/en-us/library/Windows/desktop/aa366778 (v = vs. 85) .aspx #physical_memory_limits_windows_server_2008

  

  Please allow points to useful/correct answers

• cannot access my hotmail account. have tried for more than 24 hours. now worried that everything has disappeared.

  No access to hotmail for more than 24 hours. Said they do maintenance and should not be more than an hour. Before be bleached, I had 9 unread messages, now when I sign it shows 0 next to the hotmail tab. What can I do? Nowhere to get after spending hours trying to find Hotmail and send requests on their forum.

  Submit all Live and Hotmail queries on the forum right here:

  Windows Live Solution Center
  http://windowslivehelp.com/

• Adding more than one host ESX and the upgrade at the same time.  What is the order of preference of the operations here?

  We are budgeting for more licenses and hardware for 2014 and want to do immediately in January.  I am trying to decide what is the best order of operations for adding two vmware hosts additional to our current installation of vsphere and also upgrade our vsphere / esx 4.1 u3 for the latest and best.

  We have 3 Dell PowerEdge R710 running ESX 4.1 U3.  In this vmware cluster, there is a vcenter server 4.1 U3 virtual machine handle this.  The three servers are about 90% memory used so we add 2 additional servers.  Probably the Dell PowerEdge r.620 since we get up 2 in the space of a 710.  Storage is on a san EMC NX4 NFS which will become too but not yet, let's just deal with the vmware part.

  When adding additional r.620 2, should I install ESX 4.1 on them and join them to the existing cluster and THEN pass vcenter and each one esx?  I ask precisely because 90% of use on 3 current servers, I need 2 other servers to support the update operations take place.  They would be able to repel vmotioned vm while each host receives an upgrade at the same time.

  So which is the best way to go about adding of the hosts and the upgrade?  Would I add as 4.1, then they would be available as targets vmotion and so I have room to start the hosts one upgrade at a time?

  If I update vcenter to the latest version, it is comparable backwards and can manage the 4.1 hosts, but also hosts 5.x?  I guess version 5.5 is the last one I would get from VMWare?  It is right of ESXi, then, how is this ESX ESXi 5.5 4.1 upgrade?  How much storage space do I need for ESXi 5.5, as I'm dechatoiement out of these r.620 Dell and need to know what hard drive to put in.

  The steps that you must follow

  -Updated vCenter Server

  -Upgrade of the ESX hosts (because we do a updating of the material we will install 5.5 on our new guests and add them to the cluster and then dismantle our existing)

  -Upgrade VMWare tools

  -Update data warehouses

  ESXi 5.5 has these storage requirements:

  • Installing ESXi 5.5 requires a boot device is at least 1 GB in size. When booting from a local disk or SAN/LUN iSCSI, a 5.2 GB drive is necessary to allow for the creation of the VMFS volume and a scratch 4 GB partition on the boot device. If a smaller drive or logical unit number is used, the installation program attempts to allocate a region scratching on a separate local disk. If a local drive is not found, the scratch partition (/ scratch) is located on the disk virtual ESXi host, linked to the/tmp/scratch. You can reconfigure /scratch to use another drive or logical unit number. For best performance and memory optimization, VMware recommends that you leave no /scratch on the ESXi host ramdisk.
  • To reconfigure / scratch, see Configure the Scratch Partition of vSphere Client vSphere Installation and Installation Guide.
  • Because of the sensitivity of the I/O devices, USB and SD, the installation program does not create a partition scratch on these devices. Therefore, there is no tangible benefits to the use of the great features of USB/SD that ESXi uses only the first 1 GB. When installing on USB or SD, tent Setup devices to allocate a region scratching on a local disk or the data store. If no disk is local or data store, /scratch is placed on the virtual disk. You must reconfigure /scratch to use a persistent data store after the installation.
  • In Auto deploy facilities, Setup attempts to allocate a region scratching on a local disk or the data store. If no local disk or data store is found /scratch is placed on the virtual disk. You must reconfigure /scratch to use a persistent data store after the installation.
  • For environments that start from a San or use Auto Deploy, it is not necessary to assign a separate logical unit number for each ESXi host. You can co-locate areas scrape for several hosts ESXi on a single LUN. The number of hosts assigned to a single LUN must balance the size of the LUN and behavior I/O virtual machines.

• Game-OSCustomizationSpec - GuiRunOnce adding more than one entry.

  So I try to figure out how I can change all of my current scripts by adding some registry changes more via powershell for guirunonce entry.  I find myself with an entry that contains all my changes to reg instead of multiple entries, as shown in the screenshots.  This is what I am running.

  Game-OSCustomizationSpec-spec TEST - GuiRunOnce "reg delete"HKLM\SOFTWARE\Network Associates\ePolicy Orchestrator\Agent"/v AgentGUID/f, reg delete"HKLM\SOFTWARE\Network Associates\ePolicy Orchestrator\Agent"/v MacAddress, f.

  The MultiLine.jpg shows how the spec looked before running the script.  The Oneline.jpg shows what it looks like after running the cmdlet.  Any ideas?

  Zsoldier wrote:

  Game-OSCustomizationSpec-spec TEST - GuiRunOnce "reg delete"HKLM\SOFTWARE\Network Associates\ePolicy Orchestrator\Agent"/v AgentGUID/f, reg delete"HKLM\SOFTWARE\Network Associates\ePolicy Orchestrator\Agent"/v MacAddress, f.

  Try each line in its own set of quotes, separated by a comma.

  -GuiRunOnce "reg delete 'HKLM\SOFTWARE\Network Associates\ePolicy Orchestrator\Agent' /v AgentGUID /f", "reg delete 'HKLM\SOFTWARE\Network Associates\ePolicy Orchestrator\Agent' /v MacAddress /f"
  

  =====

  Carter Shanklin

  Read the PowerCLI Blog
  [Follow me on Twitter |] http://twitter.com/cshanklin]

• validate the email - check for more than one point

  I'm looking to validate and address email and I found how to check for a simple point 'never@land. . com' with email_txt.text.indexOf('.') < 0 but I want to also want to check to see if the user may have registered two points 'never@land. . com ".

  I tried:

  email_txt.text.indexOf('.') < 0 |  email_txt. Text.IndexOf('.') > 2 but which in fact throw up all the time.

  I also tried:

  email_txt.text.indexOf('.') < 0 & & > 2 and one launched all sorts of errors.

  I don't know if I've ever seen someone check for that, so I might be a little more zealous, but I thought I'd give it a try.

  Thanks in advance

  function validateEmailF(inputEmail:String):Boolean {}
  Search for spaces
  If (inputEmail.indexOf("") > 0) {}
  Returns false;
  }
  bust of the email part in what comes before the @ and what comes after
  var emailArray:Array = inputEmail.split("@");
  Make sure that there is exactly a symbol @.
  Also make sure that there is at least one character before and after the @.
  If (emailArray.length! = 2 | emailArray [0] .length == 0 | emailArray [1] .length == 0) {}
  Returns false;
  }
  bust of share the stuff after the @ apart on any. characters
  var postArray: Array = emailArray [1].split(".");
  Make sure that there is at least one. After the @.
  If (postArray.length<2)>
  Returns false;
  }
  Make sure that there is at least 1 character in each segment before, between and after each.
  for (var i: Number = 0; i
  If (postArray [i] .length<1)>
  Returns false;
  }
  }
  Download what's left after the last.
  suffix var = postArray [postArray.length - 1];
  Make sure the end segment is 2 or 3 characters
  If {(suffix.length<2 ||="" suffix.length="">3)}
  Returns false;
  }
  It is passed all the tests, it is a valid email address
  Returns true;
  }

• Interpolation - more than one point

  Hello

  I'm trying to find the position that a graph crosses the x-axis zero. The problem is that this happens several times in my chart (this is a graph of the reactance of a parcel of impedance). I use 1 d interpolation and it returns only one point of intersection instead of 2-3 that occur. Is it possible to get all three?

  Any help would be greatly appreciated,

  Bill

  Typically when you need to detect multiple instances of a condition in a data table, you will find the first and then look for the part of the table after the first to the second.  You probably won't find a built-in function that will do this for you. The process I described in my previous post will be repeated.

  Lynn

• Cannot attach more than 1 point with IE9 Win7

  For some reason, I am unable to attach several items at a time when sending an email.  For example, sending a photo more, etc.  I can select a single item but the click + Shift does not select all and the control + click selects multiple No.  Where can I find a way to solve this problem?  It is not a question of size - it won't work in Outlook or Gmail then he owes me a Windows 7 issue or a question of IE9.

  Thank you

  Elena Lamberson

  Hey Elena,

  I suggest to follow the steps below and we update on the State of the question.

  Method 1: Run the next fixit.

  Troubleshoot Internet Explorer to IE quick, safe and stable

  http://support.Microsoft.com/mats/ie_performance_and_safety?WA=wsignin1.0

  
  Method 2: If the problem persists, I suggest you to optimize Internet Explorer.

  How to optimize Internet Explorer: http://support.Microsoft.com/kb/936213/no

  Warning:  Please note that reset it the settings of Internet Explorer running resets all settings defined by the user, including those set by the installed extensions, toolbars and other add-ons for IE by default. This includes all parameters of security, confidentiality and area. Also this will erase browsing history, delete all temporary Internet, cookies, form data files and especially all the passwords.

  Note: The measures suggested in the link above are applied to Internet Explorer 10.

  I hope this helps!

• Adding more than four levels of failure in a multiple choice quiz (5 Cp)

  Hi-

  I am currently using Captivate 5. In a quiz of multiple choice with five possible answers and only one good answer, I am only able to select up to three levels of failure. This means that if the student is wrong four times (and selects each of the four incorrect answers before finally choosing the right pair), he or she will not be served a failure with the fourth wrong answer message. Is there a remedy for this situation?

  I would like to know if I was unclear, or if you could use more information.

  Thank you!

  wcramblit

  Several slides question and answer do not have the option of advanced responses.  Yet true/false questions do not have it.  It's only for the Multiple choice questions.

  You can save a feature request for this.  Every vote helps little.

• Adding more than one locale to sample mobile TwitterTrends - works not

  Hi all

  I struggled to add local muliple support in my application so I desided to try with TwitterTrends sample application. Should be easy, but does not work for me...

  What I did:

  1 Add a locale folder to the asset with a subfolder en_US

  SRC/assets/local/en_US

  2. create a file of properties for en_US and save in src/assets/local/en_US

  SRC/Assets/local/en_US/twittertrends. Properties

  3 adding a resource key unique to view House in 'twittertrends.properties '.

  views. Home.title = Twitter trends

  4 update the TwitterTrendsHome.mxml to use, to get the title of the properties file

  title = "{resourceManager.GetString ("twittertrends","views.home.title")} '"

  5 Add the folder of locale in the path of the source of applications, I did this by changing the arguments additional compilter for Flash Builder:

  -local en_US-source-path = assets/local / {local}

  Result:

  No title appears...

  I don't know what I did wrong. Any help is very appreciated.

  Has anyone got any other seen/not seen this problem?

  See you soon,.

  
  Greg

  Try adding

  [ResourceBundle ("twittertrends")

  The problem is that the compiler is not smart enough to say that you are using the 'twittertrends' Resource Pack unless tell him both through [ResourceBundle] metadata. He's not trying to analyze the ActionScript code inside the data binding expressions to determine what parameters you pass to ResourceManager functions, etc..

  If instead of data binding, you use the @Resource () compiler directive, as in

  title="@resource ('twittertrends', 'views.home.title').

  then it should be able to understand it without the [ResourceBundle] metadata. But this way, it does not support the locale when switching running.

  Gordon Smith

  Adobe Flex SDK team

• It is impossible to ad more than a point stop on my site

  I always get the message: 'cannot create breakpoints in 25 px of an existing breakpoint.' Even if I try to do a 500 px now!

  

  I found the solution via chat. I had to change also the minimum with the site to 200 px.