Addition with sound help please

Similar Questions

• No sound help please - driver is not compatible with my version of windows

  Original title: no noise don't please help

  While UN-installing some I have programs no longer use i accidentally uninstalled my driver audio soundmax. I have a dell optiplex gx520 with the 32-bit version of windows 7 Home premium. I tried to find and re - install the driver sound max and I find one and download each time it says that the driver is not compatible with my version of windows. I would really like my back her again. also, I went into the start menu and click on the sound devices and game controllers, and all that shows is my webcam. I know that I have an internal sound card and a speaker and I know that they do not work, but when I searched for the pilot, he was gone and so I know that it is uninstalled by me when I remove other programs, I no longer use. any help you could give me would be greatly appreciated. Thank you.

  Hi Bill,

  See the link to install the drivers for the Dell OptiPlex GX520. The drivers are not available for the Windows 7 operating system. Therefore, I suggest you to install in compatibility mode and check if it works:

  Make older programs in this version of Windows

  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  Let us know the results.

• Problems with Photomerge - HELP Please!

  Hi everyone - I really hope you can help me here. I am trying to create a composite image along several other images. Sounds like a panorama, no? Well well, close, but not exactly. My photos (I'm a marine biologist) are of the ocean floor and all images have a chain or transect tape measure in them. The photos are taken separate images along the string or Ribbon, and now I'm trying to merge them into a single image of long who has the length of the Strip or the string through it. When the pictures were taken there is a lot of overlap (we usually look for a feature like a big sponge or something to include and use as a reference point).

  The problems I run into when I use photomerge are:

  (1) it is not merge all of them into a series, but gives me up to four "fixed" on a background

  (2) I don't know how to move the images around me for the best alignment (in some cases, its perfect, in many others, not so much)

  So, I can add them a facility in time? Can I move the images for the best alignment? Can I use the photomerge automated at all?

  Suggestions please! This chapter of my doctoral thesis little depends on it! Thank you!

  Looks like the algorithm has enough to work with. The general rule is that you need 40% between individual frames.

  And you need distinct features. Sand or mud will probably not work.

  I try to manually align in a first time - just stack them, reduce the opacity as needed and use the move tool or move with the arrow keys. The trick is to move, then go to Image > reveal all to extend the canvas as you go. Double-click the base layer to turn it into a floating layer, so that you do not get the solid background color on the extended canvas. Return all the opacities to 100%.

  This could help first "horizontalize" (Yes, it's a neologism) the rule in each image.

  Once you have essentially set up, make a copy and try editing > automatic alignment. This is the first step in the Photomerge script. If it works, run automatic merging - this is the second and last step.

  If automatic alignment does not work, you will need to finish manually. But you can still run the auto-merge to merge.

• Weird behavior with securities; help please

  With the premier items 13.1, I put a default title on the timeline.  I wanted it fade and then fade out per line, so I clicked on apply fade in preset and then I clicked on apply melted on the present and a present replace the other.  Looked on the web and saw no help on how to apply both at the same time.  I copied the title and applied fade in the first and fade out to the second thought that would do.  But no, when you apply fade in or fade out to the second clip that makes time independent so-called clips fade or both fade out!  You replace one and two.  What the hell is about?

  firedeva

  What operating system is involved with your elements 13/13.1 first?

  It seems that you apply to your text in the Section of titling and animation module open with his choice of text animation fades

  Fade online

  and

  Fade Out online

  You cannot apply both at the same time to the same text file. It's one or the other.

  If you want to Fade In and Fade Out a duly filled, created title in the Titler, consider

  a. close the module of titration

  b. right-click the title on the timeline, select fade in the menu that appears, followed by fade video (which gives you a 1 second Fade In).

  b. right-click right the same title in the timeline, select fade in the menu that appears, followed by Fade Out Video (which gives you a 1 second Fade Out.)

  This last leave points (keyframes) on rubberband of the file title chronology (the orange horizontal line running through the Middle clip)... you can set keyframes on the timeline level move keyframes (points) with your mouse cursor.

  Please let me know if I've targeted what you were looking for. If this isn't the case, please give more details.

  Thank you.

  RTA

  Add on... In case you encounter problems of application module of titration animation to more than one line of text in a file title, please check the details in the following how ATR first troubleshooting items: PE: titration module - part text Animations 1

  same principles for different versions of the program.

• Problem with Wireless help please!

  My computer got recently just completely wiped out. and renewed the operating drive, but

  Im having trouble getting online,

  Whenever I open Network Center and sharing, to see if theres any connection.

  It shows, and whenever I try to put in place, the only option of theres

  Dial-Up, which I have no idea how set up.

  I have a modem and a router [DIR-615] [Dlink] wireless

  I tried to connect an ethernet cable to see if she would get straight to the connection of the router and the modem. and it does not always show.

  I tried to reinstall the router information, disc, I got them, but it would not allow me to do.

  Because he couldn't detect the wired adapter.

  I checked the BIOS and I put the recovery of basic wifi, and all other points seem to be activated.

  I tried to open up to WLtray.exe

  but it gave me an error:

  The Application has failed to start because its side-by-side configuartion is incorrect. Check the log of events applications for more details.

  The wireless is not working, it certainly works on my phone exact same brother

  A Dell: Inspiron 1525

  Anything, it will just all together see wireless upward. or any other wireless connectivity.

  Basically, it does not recognize any wireless setting. all those I try to put in place, he would not go. and

  well done, my question is:

  How to configure a connection beetween my computer and wireless?

  Please help me!

  _Luke

  Hello

  Maybe this can help, http://www.ezlan.net/wireless.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Icons on the desktop and start used menu opened directly unless I use 'open with' program HELP PLEASE!

  Hello I have a huge problem and need HELP! With all the shortcuts I have on my desktop and icons that I have in my menu it start seem to be a problem. It allows me to open any programs unless I choose a program to start with. Now, I open ALL my programs with the "Open with" menu and its really a lot of time. Also I am not able to start all of the office programs, that it says I need set associations but I checked control panel and I couldn't find that. I tried the FIXIT Windows program on other issues ive had in the past and I was wondering if maybe theres a fix for the problem im having. IM currently on vista Home premium. and I really hope theres someone out there who can help me!   Thank you for your time...

  Hello

  Try the system restore before it happened.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  Its control panel - backup and restore center - left upper repair Windows

  SO which opens also to use the below to execute.

  Start - type in the search box-> rstrui.exe CONTROL the top - top - right click RUN AS ADMIN

  or use start - computer or Windows Explorer to navigate to

  C:\Windows\System32\rstrui.exe

  Top - right click RUN AS ADMIN

  =====================================

  To run a particular program until get them you all back to the normal fair use start - search and type in the
  program name or the name of the executable file - OR use start - computer or Windows Explorer to access to the
  program, and run it from there.

  Define your main program associations, and then you can edit any type of file to the correct program.

  How to set default Associations for a program under Vista
  http://www.Vistax64.com/tutorials/83196-default-programs-program-default-associations.html

  How to associate a file Extension with a program Type in Vistahttp://www.vistax64.com/tutorials/69758-default-programs.html

  How to view and change an Extension of filename on Vista
  http://www.Vistax64.com/tutorials/103171-file-name-extension.html

  How Unassociate a Type of Extension file in Vista and a utility to help
  http://www.Vistax64.com/tutorials/91920-unassociate-file-extention-type.html

  Restore the Type Associations by default Vista file extensions
  http://www.Vistax64.com/tutorials/233243-default-file-type-associations-restore.html
  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• problems with partitions - help please. [Hp dv6 2135sl]

  Hi all! So, I'm first of all I apologize for my English Italian.
  I bought a laptop HP dv6 2135sl with Windows 7 and I have a problem with the partitions.

  The partitions are all primary and the order is the sequent:
  C (450 F)
  tool HP (99MB)
  recovery (16GB)
  Sistem (199 MB)

  I would decrease C up to 50 GB and create two other partitions: J (programs 150 GB) and K (250GB of data). Is this possible? I realized that I have to change one of the 4 partitions in scope. What is the best? (Partition Wizard report an error: "no free slots of MBR"). Can I still use PM or I need something else?

  PS: Cannot use Acronis (not supprt W7) and if it's possible I won't use Gparted because I'm a noob; )

  Thank you all!

  I found a solution:

  I used the tool of W7 to handle the drive. I have create a 270 GB partition (the maximum allowed this program), then the disk was converted from basic in dinamic one disk. I opened the Partition Wizard, I turned the disc in the base. As if by magic, I found recovery logical (previously primary). Now I am able to create the partition n!

• Install problems with my help please CS2 premium

  My computer crashed and I lost most of my hard drive. So I built a new computer and CS2 doesn't let me open it once I installed. I get... No Acrobat serial number valid found. Now quit Acrobat... Help... I have project to fill...

  More details needed.

  What operating system? Did you get errors during installation?

  Bob

• Print outs are increasingly large print shown on the screen. Help please.

  Original title: print the problem

  Print outs are increasingly large print shown on the screen. This Cup is right edge

  or way to print additional pages. Help please.

  Hello

  1. facing this problem when printing from all applications or specific application?

  2. What is the serial number and model of the printer?

  You try to print the test page and verify that you are experiencing the same issue.

  To print a test page

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/print_test_page.mspx?mfr=true

• Visual Notification of need PRIVATE Blackberry Smartphones blackBerry with Gmail, but no alert sound, impossible to find how, help please?

  Help, please!

  I would like to have no sounds but the notification active just with Led

  Try the following and see if it's what you need:

  Assuming that your Gmail account is set up in the HUB

  Go to Blackberry Hub

  Press top left menu

  Tap Settings

  Go to your Gmail account

  Press the sound notification

  Now choose 'none' form the list of available sounds

• Help please with the addition of a Section of the video

  I created a video for a school organization. Have completed a section or scene, I would like to add more scenes before this scene. I know how to add things, but I don't want to start adding videos and pictures and then my audio may not be in the same place. Is it possible to add without the pictures and audio are out of sync? Can I connect the audio to the video? Help, please. Thank you!

  I guess that you do not want audio move with the clip with the fact that it is already synchronized. In this case select the video and the audio clip, right click and select "link Audio and video.

  

  See you soon,.

  --

  Neale

  Insanity is hereditary, get you your children

• No sound. Help, please!

  Qwest arrived and installed their security software, but now I have no sound.  I tried to uninstall and reinstall the driver, but it does not work.  Everything is properly connected.  The computer will play the start/stop windows songs, but it's the only sounds I get.  I have Windows XP Home Edition on a Dell desktop computer.  I called Dell and they said that it is a Microsoft driver.  I went to Microsofts driver download page, but mine is not listed.  I thought I could buy a new sound card, but Dell said my sound card is integrated and there is no slot for moving to a new.  What is missing is a midi mixer driver.  I did write the exact name, because I thought that the uninstall/reinstall would work as he had in the past.  Now, he just disappeared.  Help, please!  Thank you.

  What do you use to play these sounds - Windows Media Player, games, etc.

  Why do you think the midi mixer driver is missing?

  If you see an error message, exactly what he says?

  What security software Qwest did install?  They have a lot of security software.

  What Qwest did say when you told them that once they came and their installed security software you have discovered the sound on your system has been afflicted?

  Is your Dell system still under the factory warranty?  Call me later and I'll give you some tips for working with people for their support.

  It is usually best to get the drivers from the manufacturer of your system/motherboard and not from Microsoft, so we need to see what you have right now.

  Maybe someday the dialog box 'ask a question' forums XP will ask these questions automatically when a new thread is started so I don't have to ask every time.  It might even be possible to solve a problem in a single response when enough information is provided.

  Please provide additional information on your system:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?

  What you see you don't think you need to see?

  What do not you think that you should see?

  Now to provide information about your motherboard and system device:

  Click Start, run and enter in the box:

  Msinfo32

  Click on OK and when the system info summary appears, click on Edition, select all, copy, and then paste the information here.

  For information about the audio drivers, expand components, click Sound Device, click on edit, select all, copy and then paste the information here.

  There will be some personal information (such as the user name and the name of the system), and anything that turns information private for you, simply delete the pasted information.

  Do, or do not. There is no test.

  I decided to implement the points for a new puppy instead of a pony!

• I recently got an automatic update of Windows and now my iTunes does not... and neither is NO sound at all. Help, please!

  Windows automatic updates from time to time, and since the last of them, not only my iTunes plays not anything... my sound on my computer does not work for anything.  I can't watch any videos/tv shows/listening to music... NOTHING.  Help, please

  Remove and reinstall iTunes, QuickTime, and other software components for Windows Vista or Windows 7
  http://support.Apple.com/kb/HT1923

  Uninstall software, remove programs and solve uninstalling problems
  http://www.revouninstaller.com/

  ITunes download (32-bit):
  http://www.Apple.com/iTunes/download/

  Download 64 - bit:
  http://support.Apple.com/kb/DL1037

  If your computer has problems play a sound, try using the Audio playback problems resolution to solve the problem. For measures and additional information, see o ink below.

  Open the troubleshooting of Audio playback

  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-troubleshooterOpen

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx?type=hardware

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

  You have a fluorescent lamp next to your computer which could be emitting a rf? This could interfere with the microphone.

  In Windows 7

  Click Start > Control Panel

  Click on hardware and sound

  Under sound, click on manage audio devices

  Under playback (tab)

  Choose speakers you have in your output device

  Click Properties >

  Click levels (tab)

  check if the value is 100% >

  GoTo Enhancments > select Loudness balancing

  Apply and OK

  Should be much stronger now...

  For enhancment bit,.

  and if you have HD realtek soundmanager (R2.37) in your control panel

  Try a classic Equalizer setting

• New computer with Win 7 and I'm drowned in ads, pop ups and constant redirects. Help, please!

  I just got a new computer with Windows 7, and I had nothing else that problems with redirections constants, pop up windows, ads pasted on top of advertising.  It's really driving me crazy.  Any time I click on what (in Facebook, or my website, or Twitter or whatever it is!) I am redirected to a new tab with an advertisement trying to make me spend it, or download that.

  When I'm on Facebook, I brilliantly flashing ads covering my groups and pages.  When I opened my site, I have flashing ads to the bottom of the left and the right of my blog and all my pages.

  I tried everything I know to stop this, and nothing works.  I ran Malwarebytes, and they found pieces of adware 2029!  I quarantined and deleted and ran two additional scans that came clean, but ads and redirects are always there, drive me to madness.

  Then someone please help me, I can't use this computer as it is, it takes twice as much time to my work, and that rebounds, flashing ads are too distracting for me to even write in my blog.

  Help, please

  Check out this free removal guide: http://malwaretips.com/blogs/remove-adware-popup-ads/

• I have a new pc with win8.1 and I can't get my Photoshop Elements to 1.0.1 to install help, please.

  I have a new pc with win8.1 and I can't get my Photoshop Elements to 1.0.1 to install help, please.

  Please help with this problem of compatibility.   Thank you

  Gordonr18571658 I'm sorry I don't have any additional suggestions on how to install Photoshop elements 1.0 in addition to installing in compatibility mode for Windows XP.

  As an alternative you can find details about Photoshop elements 13 photo editor, edit photos | Adobe Photoshop Elements 13.  13 Photoshop elements has been designed for installing and running Windows 8.1.  Ago 30 day trial if you wish to evaluate the software and complete any current picture, you may be faced with editing projects.