ASA L2L IKEv1 5520 no information of its crypto isakmp

Similar Questions

• Cisco ASA l2l VPN disorder

  Hello Experts from Cisco,

  I run in trouble with one of my l2l ipec vpn between an asa 5510 and 5520 cisco running version 8.2.2.

  Our existing l2l VPN are connected fine and work very well. Currently SITE a (10.10.0.0/16) connects to the SITE B (10.20.0.0/16). SITE A connects to SITE C (10.100.8.0/21). These are OK.

  What is a failure is when I try to connect SITE B to SITE C. The tunnel coming up and phase 1 and 2 complete successfully. However, even if in the course of execution: ' entry packet - trace within the icmp 10.20.8.2 8 0 detailed 10.100.8.1 ' I get the following:

  Phase: 10

  Type: VPN

  Subtype: encrypt

  Result: DECLINE

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xad1c4500, priority = 70, domain = encrypt, deny = false

  hits = 609, user_data = 0 x 0, cs_id = 0xad1c2e10, reverse, flags = 0 x 0 = 0 protocol

  SRC ip = 10.20.0.0, mask is 255.255.0.0, port = 0

  DST ip = 10.100.8.0, mask is 255.255.248.0, port = 0, dscp = 0 x 0

  I noticed that when the tunnel came, the road to 10.100.8.0/21 was added in the routing table and cyrpto what ACL has not been applied on the SAA remote. I added the route manually but cannot get the cryto ACL to apply.

  Useful info:

  C SITE

  the object-group NoNatDMZ-objgrp network

  object-network 10.10.0.0 255.255.0.0

  object-network 10.10.12.0 255.255.255.0

  network-object 10.20.0.0 255.255.0.0

  access extensive list ip 10.100.8.0 outside_30_cryptomap allow 255.255.248.0 10.20.0.0 255.255.0.0

  IP 10.100.8.0 allow Access - list extended sheep 255.255.248.0 sheep-objgrp object-group

  card crypto outside_map 30 match address outside_30_cryptomap

  card crypto outside_map 30 peers set x.x.x.x

  crypto outside_map 30 card value transform-set ESP-AES256-SHA

  crypto outside_map 30 card value reverse-road

  outside_map interface card crypto outside

  SITE B

  object-group network sheep-objgrp

  object-network 10.10.0.0 255.255.0.0

  object-network 10.21.0.0 255.255.0.0

  object-network 10.10.12.0 255.255.255.0

  network-object 10.100.8.0 255.255.248.0

  IP 10.20.0.0 allow Access - list extended sheep 255.255.0.0 sheep-objgrp object-group

  allow outside_50_cryptomap to access extended list ip 10.20.0.0 255.255.0.0 10.100.8.0 255.255.248.0

  card crypto outside_map 50 match address outside_50_cryptomap

  game card crypto outside_map 50 peers XX. XX. XX. XX

  outside_map crypto 50 card value transform-set ESP-AES256-SHA

  outside_map crypto 50 card value reverse-road

  outside_map interface card crypto outside

  I've been struggling with this these days. Any help is very appreciated!

  Thank you!!

  Follow these steps:

  no card outside_map 10-isakmp ipsec crypto dynamic outside_dyn_map

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  clear crypto ipsec its SITE_B_Public peer

  Try again and attach the same outputs.

  Let me know.

  Thank you.

• ASA L2L VPN UP with incoming traffic

  Hello

  I need help with this one, I have two identical VPN tunnel with two different customers who need access to one of our internal server, one of them (customer) works well, but the other (CustomerB) I can only see traffic from the remote peer (ok, RX but no TX). I put a sniffer on ports where the ASA and the server are connected and saw that traffic is to reach the server and traffic to reach the ASA of the server then nothing...

  See the result of sh crypto ipsec his below and part of the config for both clients

  ------------------

  address:

  local peer 100.100.100.178

  local network 10.10.10.0 / 24

  local server they need access to the 10.10.10.10

  Customer counterpart remote 200.200.200.200

  Customer remote network 172.16.200.0 / 20

  CustomerB peer remote 160.160.143.4

  CustomerB remote network 10.15.160.0 / 21

  ---------------------------

  Output of the command: "SH crypto ipsec its peer 160.160.143.4 det".

  address of the peers: 160.160.143.4
  Tag crypto map: outside_map, seq num: 3, local addr: 100.100.100.178

  outside_cryptomap list of allowed access host ip 10.10.10.10 10.15.160.0 255.255.248.0
  local ident (addr, mask, prot, port): (10.10.10.10/255.255.255.255/0/0)
  Remote ident (addr, mask, prot, port): (10.15.160.0/255.255.248.0/0/0)
  current_peer: 160.160.143.4

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 827, #pkts decrypt: 827, #pkts check: 827
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #pkts not his (send): 0, invalid #pkts his (RRs): 0
  #pkts program failed (send): 0, #pkts decaps failed (RRs): 0
  #pkts invalid prot (RRs): 0, #pkts check failed: 0
  invalid identity #pkts (RRs): 0, #pkts invalid len (RRs): 0
  #pkts incorrect key (RRs): 0,
  #pkts invalid ip version (RRs): 0,
  replay reversal (send) #pkts: 0, #pkts replay reversal (RRs): 0
  #pkts replay failed (RRs): 0
  #pkts min frag mtu failed (send): bad frag offset 0, #pkts (RRs): 0
  #pkts internal err (send): 0, #pkts internal err (RRs): 0

  local crypto endpt. : 100.100.100.178, remote Start crypto. : 160.160.143.4

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: C2AC8AAE

  SAS of the esp on arrival:
  SPI: 0xD88DC8A9 (3633170601)
  transform: esp-3des esp-md5-hmac no compression
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 5517312, crypto-card: outside_map
  calendar of his: service life remaining (KB/s) key: (4373959/20144)
  Size IV: 8 bytes
  support for replay detection: Y
  Anti-replay bitmap:
  0xFFFFFFFF to 0xFFFFFFFF
  outgoing esp sas:
  SPI: 0xC2AC8AAE (3266087598)
  transform: esp-3des esp-md5-hmac no compression
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 5517312, crypto-card: outside_map
  calendar of his: service life remaining (KB/s) key: (4374000/20144)
  Size IV: 8 bytes
  support for replay detection: Y
  Anti-replay bitmap:
  0x00000000 0x00000001

  -The configuration framework

  ASA Version 8.2 (1)

  !

  172.16.200.0 customer name

  name 10.15.160.0 CustomerB

  !

  interface Ethernet0/0

  nameif outside

  security-level 0

  IP 100.100.100.178 255.255.255.240

  !

  interface Ethernet0/1

  nameif inside

  security-level 100

  10.10.10.0 IP address 255.255.255.0

  !

  outside_1_cryptomap list extended access allowed host ip 10.10.10.10 customer 255.255.240.0

  inside_nat0_outbound_1 list extended access allowed host ip 10.10.10.10 customer 255.255.240.0

  inside_nat0_outbound_1 list extended access allowed host ip 10.10.10.10 CustomerB 255.255.248.0

  outside_cryptomap list extended access allowed host ip 10.10.10.10 CustomerB 255.255.248.0

  NAT-control

  Overall 101 (external) interface

  NAT (inside) 0-list of access inside_nat0_outbound_1

  NAT (inside) 101 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 100.100.100.177

  Route inside 10.10.10.0 255.255.255.0 10.10.10.254 1

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  card crypto outside_map 1 match address outside_1_cryptomap

  card crypto outside_map 1 set pfs

  peer set card crypto outside_map 1 200.200.200.200

  card crypto outside_map 1 set of transformation-ESP-3DES-SHA

  card crypto outside_map 3 match address outside_cryptomap

  peer set card crypto outside_map 3 160.160.143.4

  card crypto outside_map 3 game of transformation-ESP-3DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 20

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP ipsec-over-tcp port 10000

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec svc

  internal customer group strategy

  Customer group policy attributes

  Protocol-tunnel-VPN IPSec svc

  internal CustomerB group strategy

  attributes of Group Policy CustomerB

  Protocol-tunnel-VPN IPSec

  tunnel-group 160.160.143.4 type ipsec-l2l

  tunnel-group 160.160.143.4 General-attributes

  Group Policy - by default-CustomerB

  IPSec-attributes tunnel-group 160.160.143.4

  pre-shared key xxx

  tunnel-group 200.200.200.200 type ipsec-l2l

  tunnel-group 200.200.200.200 General attributes

  Customer by default-group-policy

  IPSec-attributes tunnel-group 200.200.200.200

  pre-shared key yyy

  Thank you

  A.

  Hello

  It seems that the ASA is not Encrypting traffic to the second peer (However there is no problem of routing).

  I saw this 7.x code behaviors not on code 8.x

  However you can do a test?

  You can change the order of cryptographic cards?

  card crypto outside_map 1 match address outside_cryptomap

  peer set card crypto outside_map 1 160.160.143.4

  map outside_map 1 set of transformation-ESP-3DES-MD5 crypto

  card crypto outside_map 3 match address outside_1_cryptomap

  card crypto outside_map 3 set pfs

  peer set card crypto outside_map 3 200.200.200.200

  card crypto outside_map 3 game of transformation-ESP-3DES-SHA

  I just want to see if by setting the peer nonworking time to be the first, it works...

  I know it should work the way you have it, I just want to see if this is the same behavior I've seen.

  Thank you.

  Federico.

• Disconnecting from the VPN ASA L2L - CheckPoint

  Hello...

  Please your help...

  I configured a L2L VPN between an ASA5505 and CP2070.

  The tunnel is working, we have conectivity between sites, but the tunnel is disconnect periodically.

  When the tunnel fails, we have a 'clear crypto isakmp his "to retrieve the connection."

  I tested changing the parameters of life expectancy in IKE and IPSec configurations, but the problems persist.

  Any suggestion?

  The ASA configuration file is attached.

  Hello

  If solve you the problem by disabling the tunnel on the side of the ASA, I think that there is a loss of connectivity on the side of control point when this happens?

  I mean... the ASA still belives the tunnel is mounted, but it is not because that is not upward on the side of the checkpoint.

  Once you have disabled the SAs on the SAA, the tunnel to renegotiate and restores.

  There are DPD packets that can be sent to monitor the health of the peer VPN and KeepAlive, but they work a lot between Cisco devices. (I don't know if there are problems of incompatibility with other brands).

  Can you verify if this is the problem?

  In addition, is the ISAKMP phase 1 and phase 2 lives the same value two units?

  Federico.

• ASA L2L IP WAN au Public

  Hi all

  I have an obligation to set up a private network virtual of our network for a developer with the following basic topology:

  Our private subnet - ASA (WAN IP) - VPN - end developer audience - protected Developer Public IPs point

  If the developer has a bunch of public IPs protected behind a single endpoint, so that we can have access, we have our external IP to establish a VPN to this endpoint.

  I understand that we will not use NAT as internal IP addresses will be PAT behind the external IP - traffic to the IPs developer audience then will bring up the VPN tunnel and everything works as expected (I think?)

  Here is the config to base on the top of my head, is - this correct or I get very confused?

  network of the DEVELOP1 object
  host 2.2.2.2
  object OUR - WAN network
  host 1.1.1.1
  the object of OUR LAN network
  192.168.10.0 subnet 255.255.255.0
  !
  NAT (vlan10, outside) after the automatic termination of dynamic source OUR - OUR - WAN LAN
  !
  outside_cryptomap extended access list allow OUR WAN ip object DEVELOP1
  !
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  !
  card crypto outside_map 1 match address outside_cryptomap
  card crypto outside_map 1 set counterpart 5.5.5.5
  card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
  !
  outside_map interface card crypto outside
  !
  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  lifetime 28800
  !
  internal GroupPolicy_5.5.5.5 group strategy
  attributes of Group Policy GroupPolicy_5.5.5.5
  Ikev1 VPN-tunnel-Protocol
  tunnel-group 5.5.5.5 type ipsec-l2l
  tunnel-group 5.5.5.5 General attributes
  Group - default policy - GroupPolicy_5.5.5.5
  IPSec-attributes tunnel-group 5.5.5.5
  IKEv1 pre-shared-key thepassword

  Hello

  You can have communication with the public IP to L2L tunnel stack... What you need is NAT/PAT at both ends and your statement of cryptomap should be with your NAT or PAT... instead of... private LAN address by looking at your config, it seems to be okay... I also hope that your LAN users only launch the right of movement?

  Because to get out, you can have a generic Pat... but when the other end accepts traffic be tone should have a dedicated static NAT or direct public IP of the servers to an end... or at least King of thing port forwarding, they should have done on their end... If both ends have a generic pat then it won't work.

  Concerning

  Knockaert

• ASA at the ASA L2L VPN Firewall

  Hi experts,

  I currently have problems establishing a VPN site-to-site easy. It's my first time at this meeting and I am pulling my hair out for this issue.

  Currently, the installation program below is a typical topology (using ASDM):

  An ASA IP (1.1.1.2) of the site <-->(ISP) <-->Site B (ASA IP 2.2.2.2)

  All ASA IPs are the external interface connecting directly to their respective suppliers. Site has existing VPN tunnels to other networks, but Site B is a new network configuration (one can imagine Site A as a hub and the rest are rays). Site B outside interface opened ports IP 50 ESP, UDP 500 and UDP 4500 on the interface of all sources to connect to the external interface (besides us has allowed all the IP protocol for the external interface for troubleshooting). However, we have issues that phase 1 upward. We have carefully matched and double checked IKEv1 all the settings are correct and the same for the two parties, including the PSK. However Site A can ping IP of the Site B and Site B is not able to ping to the Site A IP.

  We also checked with our Internet service providers and they confirmed that they do not block 3 ports we need for the VPN. Is there more ideas or points that we missed?

  Oh, activation of debugging are not returned all the papers, but will help generate some 'interesting' traffic such as internal ping subnet of Site A of the Site B?

  Hello

  Instead of launching the plotter of the interface IP packets use all other inside IP, I see a failure of ifc interface.

  Also is it possible for you to take the UDP 500 captures on the external interfaces on the SAA?

  This would answer a lot of questions.

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• ASA L2L VPN NAT

  We have a partner that we set up a VPN L2L with.  Their internal host IP infringes on our internal IP range.  Unfortunately, they are not offer NAT on their side.  Is it possible on the SAA to configure a NAT device for my internal hosts will say 1.1.1.1 and ASA changes the internal address of the remote end overlapping?

  If this is the scenario

  192.168.5.0 ASA1 <---> <-- internet="" --="">ASA2<-->

  ASA1 (NAT will be applied)

  ASA2 (without nat will be applied)

  You want to do something like that on ASA1

  Change your source host or network to be 192.168.7.0 when communicating with the remote network. Change the remote network to come as long as 192.168.8.0 coming to your network on the SAA.

  ACL soccer match:!-match-list ACLaccess acl_match_VPN ip 192.168.7.0 allow 255.255.255.0 192.168.5.0 255.255.255.0

  ! - NAT ACL

  vpn_nat 192.168.5.0 ip access list allow 255.255.255.0 192.168.8.0 255.255.255.0

  ! - Translations

  public static 192.168.7.0 (exterior, Interior) 192.168.5.0 netmask 255.255.255.0 0 0

  static (inside, outside) 192.168.8.0 public - access policy-nat list

  Complete the VPN configuration using acl_match_VPN as the ACL match. Your inside host will have to use the 192.168.7.0 network when you talk to the remote end.

  I hope this helps.

• How to accompany the IDS in ASA 5505 and 5520?

  Dear All;

  We have the following configuration of HW for the ASA 5505 and ASA 5520, we add the functionality of system of detection of Intrusion (IDS) to the two ASA. My question is: what are the modules required to support this function, and what is the deference between IPS and IDS, fact the same Module both the feature?

  Part number:	Description	QTY.
  ASA5505-BUN-K9	ASA 5505 appliance with SW 10 users, 8 ports, 3DES/AES	1
  CON-SNT-AS5BUNK9	SMARTNET 8X5XNBD ASA5505-BUN-K9	1
  SF-ASA5505 - 8.2 - K8	ASA 5505 Series Software v8.2	1
  CAB-AC-C5	Power supply cord Type C5 U.S.	1
  ASA5500-BA-K9	ASA 5500 license (3DES/AES) encryption	1
  ASA5505-PWR-AC	ASA 5505 power adapter	1
  ASA5505-SW-10	ASA 5505 10 user software license	1
  SSC-WHITE	ASA 5505 hood SSC of the location empty	1
  ASA-ANYCONN-CSD-K9	ASA 5500 AnyConnect Client + Cisco Security Office software	1

  Part number:	Description	QTY.
  ASA5520-BUN-K9	ASA 5520 appliance with SW HA, 4GE + 1FE, 3DES/AES	2
  CON-SNT-AS2BUNK9	SMARTNET 8X5XNBD ASA5520 w/300 VPN Prs 4GE + 1FE3DES/AES	2
  ASA5520-VPN-PL	ASA 5520 VPN over 750 IPsec User License (7.0 only)	2
  ASA-VPN-CLNT-K9	Cisco VPN Client (Windows Solaris Linux Mac) software	2
  SF - ASA - 8.2 - K8	ASA 5500 Series Software v8.2	2
  CAB - ACU	Power supply cord (UK) C13 BS 1363 2.5 m	2
  ASA-180W-PWR-AC	Power supply ASA 180W	2
  ASA5500-BA-K9	ASA 5500 license (3DES/AES) encryption	2
  ASA-ANYCONN-CSD-K9	ASA 5500 AnyConnect Client + Cisco Security Office software	2
  SSM-WHITE	ASA/IPS SSM hood of the location	2

  Thanks in advance.

  Rashed Ward.

  Okay, I was not quite correct in my first post.

  These modules - modules only available for corresponding models of ASA.

  They all can act as IPS (inline mode) or IDS ("Promiscuous" mode), depending on how you configure your policies.

  When acting as IPS, ASA redirects all traffic through the module, then all the traffic is inspected and can be dropped inline if a signature is triggered.

  When she acts as an ID, ASA a few exemplary traffic is the module for inspection, but the actual traffic is not affected by the module, as it's not inline in this case.

  In addition, these modules can be both comdination. That is part of the traffic can be inspected "inline", when some other (more sensitive) traffic can be inspected in promiscuous mode.

  To better understand, familiarize themselves with this link:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/modules_ips.html

• Cisco ASA - l2l IPSEC tunnel two dynamic hosts

  Hello

  I have two firewall Cisco ASA an i want to made a l2l between two ipsec tunnel, the problem is that both parties have a dynamic IP, on both sides I have configured dyndns, can I did an ipsec tunnel using dyndns name such as address peer?

  Hello

  ASA supports only the RFC compliant method for updates used with dynamic DNS, not updates HTTP, such as dyndns.org and others use.
  i.e. https://tools.cisco.com/bugsearch/bug/CSCsk25102/?reffering_site=dumpcr

  On ASA, it is not possible to configure the tunnel between two dynamic peers.
  You will need to have a static end to configure static to dynamic IP.

  For routers, you can follow this link.
  I hope this helps.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• ASA L2L filter-VPN Tunnels

  I need help to understand how the vpn-filter command is applied to the traffic tunnel.  Until very recently, I was under the command of printing the vpn-filter (applied in Group Policy) provided an access control incoming (outside to inside) for VPN traffic after decryption.  Recently I change any of my VPN connections (add a phase access list entry 2) which causes questioning me how the vpn-filter.

  Example-

  original vpn connection - my side hosted the server and the clients were on the other side.  My vpn-filter rule has allowed customers to come to my server.

  more - (above the original setting still in place) - the other side is now hosting a server and on my side has clients.

  Without any changes to vpn-filter, I have lived: phase 2 built tunnel but no packet encryption or decryption and no error in syslog.

  Using packet - trace, I discovered a list of access (vpn-user subtype) blocked access.  "vpn-user" must be a Cisco term because it is not in my config.  I added an entry to my vpn-filter acl allowing their server to talk to my clients.  Adding to the vpn-filter enabled that the tunnel started working.

  I would have thought

  vpn-filter acl was dynamic and not required an entry

  or

  the without the vpn-filter acl, the phase would have shown his encryption/decryption and perhaps an acl deny message in the system log.  Basically, the traffic is encrypted, returns server, decrypted and then dropped access policy.

  Have a further explanation or documentation?

  Thank you

  Rick

  Rick,

  The problem is that the ACL applied through the vpn-filter is not dynamic.

  A vpn-filter command applies to traffic after decrypted once it comes out a tunnel and the previously encrypted traffic before entering a tunnel. An ACL that is used for a vpn-filter should NOT also be used to access interface group. When a vpn-filter command is applied to a group policy which governs customer connections access remote VPN, the ACL must be configured with the assigned client IP addresses in the position of src_ip of the ACL and the LAN in the position of dest_ip of the ACL.

  When a vpn-filter command is applied to a political group that governs a connection VPN from LAN to LAN, the ACL must be configured with the remote network in the position of src_ip of the ACL and the LAN in the position of dest_ip of the ACL.

  Caution when the construction of the ACL for use with the vpn-filter feature. The ACL are built with traffic after decrypted in mind. However, ACL also apply to the oncoming traffic. For this previously encrypted traffic that is intended for the tunnel, the ACL are built with exchanged src_ip and dest_ip positions.

  More information here:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_groups.html

  It will be useful.

  Federico.

• ASA L2L Tunnel 8.3 NAT helps

  I read all the messages that I could find, every bit of documentation, I could find and still cannot get my head around how I have to configure this new ASA to meet the requirements.  My client's implementation of a new data center and going to migrate to this new domain controller.  They currently have an old PIX-515E clocked 6.3 to their existing data center.  I need to imitate the configuration on a new ASA 8.3 running.  I think I got all the NAT static etc, but I'm stuck on the configuration of their two tunnels they use.  The relevent to the old PIX configuration is pasted below. I don't get the ACL, etc. in full as there are a lot of old tunnels, etc. which do not pass.  Only the parts that are relevant to these two tunnels are below.  Also, many of the elements from the old configuration do not make sense and I don't know what is actually happening.

  Global 1 interface (outside)
  NAT (inside) - 0 100 access list
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  public static 172.30.6.65 (Interior, exterior) 10.0.0.130 netmask 255.255.255.255 0 0

  allowed for line of the access list 100 11 ip 10.0.0.0 255.0.0.0 10.0.0.0 255.0.0.0 (hitcnt = 80740)

  allowed for line of the access list 100 39 host ip 10.0.0.130 2.9.37.0 255.255.255.0 (hitcnt = 13531)

  outside_cryptomap_220 list of allowed access host ip 10.0.0.130 2.9.37.0 255.255.255.0
  outside_cryptomap_220 ip 172.30.6.64 access list allow 255.255.255.248 2.9.37.0 255.255.255.0

  access-list 181 allow ip 10.0.0.0 255.0.0.0 10.0.26.0 255.255.255.0

  gersmap 220 ipsec-isakmp crypto map

  card crypto gersmap 220 correspondence address outside_cryptomap_220

  peer set card crypto gersmap 220 64.87.28.38

  card crypto gersmap 220-transform-set-3DES-SHA

  gersmap 241 ipsec-isakmp crypto map

  correspondence address card crypto gersmap 241 181

  card crypto gersmap 241 counterpart set 74.238.28.7

  card crypto gersmap 241 transform-set dblsecure3

  gersmap interface card crypto outside

  ISAKMP allows outside

  Here are some configuration information that was sent to the customer to the company remote.

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Fort-ASA01 # sh crypto ipsec peer of his FLOO1

  peer address: FLOO1

  Tag crypto map: toVPNClients, seq num: 17, local addr: 64.87.28.38

  2.9.37.0 IP Access-list extended floo1 255.255.255.0 allow 172.30.6.64 255.255.255.248

  local ident (addr, mask, prot, port): (2.9.37.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (172.30.6.64/255.255.255.248/0/0)

  current_peer: FLOO1

  Thank you for any assistance in getting this set up correctly

  You're absolutely perfect.

  This is the correct instruction of NAT, IE: 10.0.0.130 will be coordinated to 172.30.6.65 when the destination is 2.9.37.0/24.

• Hello, I am divorced and my ex has my Apple ID password and your email address, I need to know the easiest way to change the information to its own as well as to iCloud without losing my email address?

  Hello, I got divorced a few years back and my ex-wife got custody of the children so I went never to change the identifier Apple or iCloud. My question is how do I transfer my name, payment information and email address off the Apple ID and then transfer it to her (she was stalking my phone) I'll sign account of my wife new apple but must still be able to give this account to my ex and the son who bought a ridiculous amount of songs is only fair! So to sum up, I am currently connected to my iphone under [email protected] for iTunes Store, App Store, icloud and gamecenter and want to give the said account son and crazy ex so that they do not lose their music and I stop doing stalked!

  Contact Apple for assistance. There is nothing that you can do yourself and we can nothing what to do to help.

  Apple Store Customer Service at the the 1-800-676-2775 or see the online help for more information.

  Contact product support and tech: Contacting Apple for support and service - this includes

  numbers of international calls...

  Mac App Store: Apple - Support - Mac App Store.

  For iTunes: Apple - Support - iTunes.

• WCCP and ASA L2L VPN Tunnel

  How L2L WCCP vpn tunnel? If there is a Web page on the otherside of the tunnel that I need access on ports 80 and 443, it goes through the process of WCCP. How will I know the traffic through the tunnel for 80 and 443 to ignore the WCCP?

  Hello

  I have not had to deal with WCCP on the SAA configurations as it, but to my knowledge, this could be done in the ACL that is used in configuring WCCP on the SAA.

  I mean a single montage we have has an ACL that simply bypasses the WCCP for some destination addresses.

  The ACL was originally for example

  WCCP ip access list allow a whole

  Then we had to stop it for some destination network and we would add a Deny statement at the top of the ACL

  access-list 1 deny ip WCCP line any 10.10.10.0 255.255.255.0

  -Jouni

• Move on to a different physical interface same ASA L2L tunnel

  Some may describe the process to move a tunnel L2L existing since one physical interface to another?

  Thank you!

  Sent by Cisco Support technique iPhone App

  Add the map encryption to the new interface

  card crypto IPSEC interface new_outside

  You will also need to add isakmp to the new interface

  ISAKMP crypto enable new_outside

  If you have a new public IP address, then you will need to create a new VPN Group also.

• How do you set up when TMS purge the information from its database?

  Hi all

  I would purge the Pb on my TMS server and cannot find information on how to do it.

  My server is encountering the limit of 4 GB for the DB SQL 2005 I have running.  I want to prevent the server from suffocation, so I pulled back the number of days THAT TMS stores for newspapers but he cannot find a way to initiate a purge so the DB can make room for new conferences.

  I know what's happening every night at midnight, but I prefer to be able to open the purge now.

  Is anyway to do this?  Is there a way to change the default time of calendar purge?

  Thanks for the help,

  Shawn

  You cannot manually start the jobs of the TMS product interfaces.  They will work based on the calendar automatically in the background.

  To see when they will work, Goto administrative tools-> active and look for the work listed as "purge the data expired in the tables.

  BTW, if you upgrade to SQL Express 2008 2012, the database limit is much higher (10 GB).  In addition, support for 2005 will be removed from newer versions of TMS little.