behavior reversed stacking bug?

Similar Questions

• Satellite A60-122: cooling systems and Power Saver bugs

  There are two methods of cooling for my laptop: "Max Performance" and "battery optimized". Well, I read what the manual says these plans, but my comments are a little different. I discovered that under the regime of 'Battery optimized' only the main fan works (the one with the processor), while according to the 'Max performance' secondary fan speed works.

  The problem is in the passage between the plans: once the 'Max performance' is turned on, and then the computer is switched back to "Battery optimized", the secondary fan will never stop. It is very worrying, because the secondary fan is noisy. Any ideas how to solve this problem?

  I have the latest version of the BIOS (1.90) so that the last program energy savings.

  Hello

  Sorry, but I don t think you're hardware engineer, designer hardware or software maybe developer to define certain behaviors such as bug. Or I'm wrong about this? ;)

  How old is your A60? Have you ever cleaned the unit and remove the dust? The device can be cooled properly? Please clean it properly and unit will be able to catch his breath. That means that the cooling fans work slowly and certainly not so often. After cleaning my old Satellite P20 (three vents) laptop was much quieter.

  Energy saver is created for the optimization of the battery, and allow the user to define how the phone should work with the battery or the power supply current. This optimization means low energy consumption and longer work with battery power supply.

  > The problem is in the passage between the plans: once
  > "Max performance" is turned on and then the computer
  > is switched back to "Battery optimized", the
  > secondary fan will never stop. It is very disturbing,
  > since the secondary fan is noisy. All ideas
  > How do I fix this?

  It's a very interesting question and I have tested on my laptop and it works well. I spent several times between the profiles and the result is always the same: fun runs on max performance but every time when I switch to the optimized battery cooling fan stops immediately. Try it please create own profile with a minimum level of activity of the CPU and cooling method. Connect it to the power supply and with FN + F2 switch between profiles.

  In the end, if there is a bug I think that these last two years (unit must be about two and a half years) it should be fixed long ago.

• Sending pictures to email - not set in order - and reverse before getting them

  I selected a series of photos in a folder in the picture library - 1st pic-clicked and clicked on the last offset.

  Photos were numbered from SAM_005 to SAM_016 and when sent to the Email SAM_016 has been attached 1 SAM_005, 006, etc - so out of sequence in my captions in my text of the e-mail.

  Even worse, when I sent the email in my sent folder, the entire list of attachments reversed in the slideshow - so my captions in my emial text were back to the slide show.

  I missed you to use send to mail recipient of the message.  You can manually create a message, then add them in reverse order.    Hotmail issues apply here: www.windowslivehelp.com
   
  Steve
   
  wrote in message News: * e-mail address is removed from the privacy *...

  Have wrong answer Steve, you tried?

  Make them individually creates a separate for each - e-mail defeats the purpose to send quickly a group of images.

  It is an obvious BUG in send it to / recipient of Email from programming and should be fixed - please report it if you have a sweater.

  Also, as I noted in my original post, after having sent the e-mail to a group of recipients and then going to Hotmail to forward my email sent, attachments are reversed - another BUG that should be reported and fixed.

  Software should work intuitively that the user expects!

• Question of layout on VBox with different content (bug or not?)

  I don't know if the following behavior is a bug, or scheduled. At least the behavior has changed since 2.2 to the last beta 8.

  I have VBox container. Inside is a ListView and a BorderPane. The content in the center of the BorderPane can be changed between a text box and a WebView. When that happens, the height of the ListView changes. (No additional constraints have been put on one of the nodes).

  I'm not enough of an expert layout of course what happens here. The desired behavior would be that ListView (or across the top of the VBox) has a constant size, does not matter what is in the rest of the VBox. If the observed behavior is intended, how can I get the desired behavior?

  Complete code below.

  package jbugs;
  
  import javafx.application.Application;
  import javafx.stage.Stage;
  import javafx.scene.layout.BorderPane;
  import javafx.scene.control.Button;
  import javafx.event.EventHandler;
  import javafx.event.ActionEvent;
  import javafx.scene.control.ToolBar;
  import javafx.scene.layout.VBox;
  import javafx.scene.control.ListView;
  import javafx.scene.control.TextArea;
  import javafx.scene.web.WebView;
  import javafx.scene.Scene;
  
  public class WebViewLayoutBug extends Application {
  
    public void start(Stage stage) {
  
      BorderPane root = new BorderPane();
  
      Button text = new Button("TextArea");
  
      Button web = new Button("WebView");
      ToolBar toolbar = new ToolBar(text, web);
  
      VBox vb = new VBox();
  
      ListView<String> lv = new ListView<String>();
     
      lv.getItems().addAll("foo", "bar");
  
      final BorderPane bp = new BorderPane();
  
      vb.getChildren().addAll(lv, bp);
  
      final TextArea textArea = new TextArea();
      final WebView webView = new WebView();
  
      text.setOnAction(new EventHandler<ActionEvent>() {
        public void handle(ActionEvent e) {
          bp.setCenter(textArea);
        }
      });
  
      web.setOnAction(new EventHandler<ActionEvent>() {
        public void handle(ActionEvent e) {
          bp.setCenter(webView);
        }
      });
  
      root.setTop(toolbar);
  
      root.setCenter(vb);
     
      stage.setScene(new Scene(root, 800, 600));
      stage.show();
    }
  
  }
  
  

  This has exactly the same for me in 1.7.0_40 JDK and JDK 1.8.0 b109.

  The desired behavior would be that ListView (or across the top of the VBox) has a constant size, does not matter what is in the rest of the VBox. If the observed behavior is intended, how can I get the desired behavior?

      lv.setMinHeight(Control.USE_PREF_SIZE);
      lv.setMaxHeight(Control.USE_PREF_SIZE);
  

• IaaS > pass = strange behavior catalog

  I have a setup clean enough vcd.

  2 x iaas boxes which are essentially clean win2k3 os with a single partition.

  These are verified in the masters gold.

  I'm building a paralytic that contains 6 of the IAAS models in a confgiuration PAAS integrated with different disk / nic configurations.

  When I add the TIME of 6 boxes to the catalog (as scenario PAAS) I see no longer the IAAS models when you add a new vApps.

  I don't see templates that have been added since the new VAPP containing 6 boxes.

  If I delete the VAPP PAAS all IAAS models are available again. Is this standard behavior or a bug?

  This average PAAS configurations must be stored in different catalogs to IAAS configurations? Seems odd.

  Yes, we show only so many people... and don't forget to turn the page

• CreateInsert: table auto refresh, bug or feature?

  I noticed something strange.
  I have a table that is linked to a domain controller. I also have a button with custom code. In this code, I run the CreateInsert and open a popup.
  It works very well.
  
  I noticed that a blank line gets my table as soon as I press the createInsert button, however there are no partialTrigger from my table to the button. Is this a normal behavior or a bug?
  
  This is the code of my table:
  

  <af:table value="#{bindings.User.collectionModel}" var="row"
                rows="#{bindings.User.rangeSize}"
                emptyText="#{bindings.User.viewable ? 'No data to display.' : 'Access Denied.'}"
                fetchSize="#{bindings.User.rangeSize}" rowBandingInterval="0"
                filterModel="#{bindings.UserQuery.queryDescriptor}"
                queryListener="#{bindings.UserQuery.processQuery}"
                filterVisible="true" varStatus="vs"
                selectedRowKeys="#{bindings.User.collectionModel.selectedRow}"
                selectionListener="#{bindings.User.collectionModel.makeCurrent}"
                rowSelection="single" id="t1" width="850px"
                autoHeightRows="10" contentDelivery="immediate">

  It's the actionListener for my button:
  

      public void createUser(ActionEvent e) {
        BindingContainer bindings = BindingContext.getCurrent().getCurrentBindingsEntry();
        OperationBinding createInsert = (OperationBinding) bindings.get("CreateInsert");
        createInsert.execute();
        
        FacesContext facesContext = FacesContext.getCurrentInstance();
        ExtendedRenderKitService service = Service.getRenderKitService(facesContext, ExtendedRenderKitService.class);
        service.addScript(facesContext,"AdfPage.PAGE.findComponent('"+popup.getClientId(facesContext) + "').show();");
      }

  My button has the partialSubmit = "true" so I don't see why the table is notified and adds the empty line.
  I want to just open the popup and show the field in the record.
  
  Published by: Yannick Ongena Sep 23, 2010 10:50

  Hi Yannick,

  Seems you and debugger do the same popup and Create/Insert button

  Edit: Ah, I just noticed that you say that you see the line in the table immediately... not sure that one (I see the line after rejecting the popup). I am downloading of clusters of JDev extensions right now, so I can't test my approach immediately, but I'll do it soon.

  Note: I recommend that you use the API server to display the popup rather than injecting JavaScript - see my sample code to this other thread - this method to display a popup is the way documented to do so in an actionlistener.

  John

• -Pop-up windows can not scroll?

  I noticed that in comparing to other browsers when there is a pop-up, for example when you use PrintFriendly to print the page I'll be staying - this pop-up window is not at all, making it impossible to decide what to print or not scrollable.

  I would like to know if you would like to clarify me the problem more or give an example of a problem?

  Unfortunately this uses shareaholic and bury code in some minimized js code (and as I am not web developer myself i can't make much sense of it unfortunately).

  According to http://www.w3schools.com/jsref/met_win_open.asp , it seems that chrome and webkit browsers are simply not address the setting of scrollbars in Window.Open)

  your only options may be to report this behavior as a bug of shareaholic (https://shareaholic.com/contact) or to implement the functionality of printfriendly manually yourself...

• DAQmxGetWriteTotalSampPerChanGenerated returns an incorrect number of scans generated after 25 minutes

  Hello

  When you use DAQmxGetWriteTotalSampPerChanGenerated, I noticed that I get a wrong number of generated scans when running analog output continuous for more than 25 minutes. After some debugging I realized that the generated value returned by DAQmxGetWriteTotalSampPerChanGenerated scans wraps around 2 ^ 32 despite the uInt64 data type. I checked that the data using NOR-DAQmx C reference type indicates indeed uint64 and not such a limitation is documented, so I just wanted to check if it was a normal behavior or a bug.

  I see this behavior with the NI USB-6255 housing, operating at the maximum sampling rate for about 25 minutes.

  I use a machine Win64 with NIDAQmx driver version 9.3.0f2.

  TaskHandle taskHandle = 0;

  uInt64 data = 0;

  ...

  DAQmxGetWriteTotalSampPerChanGenerated (taskHandle & data)

  Attached is a Trace of e/s OR illustrating this issue.

  Thank you

  Bruno w,

  The MathWorks

  This behavior has been reported on X as a Corrective Action Request (CAR) 353282 series.  I will update the CAR in order to take into account that it is a problem for the M series as well.

  In the short term, you can work around this problem by adding n * 2 ^ 32 (where n = number of rolls above) to the value returned by TotalSampPerChannelGenerated case where you would see that "TotalSampPerChannelGenerated" has declined.

  Dan

• How can I remove an account from synergy, Palm across the profile

  I have reported this Palm support, but I hope that someone else has seen cela and knows the answer (Hardbeatz, this should be easy for you).

  I let someone else connect to their facebook account on my pre +. He immediately put all his contacts in my contact list. Not what I wanted. So I deleted this account in the Facebook application, in the address book application and everywhere else, I could find a reference to it.  However, when I "sync" my Palm profile, this e-mail address continues to appear and returns the error that he uses an invalid password (Fortunately he didn't remember". So, whenever I have sych my profile, I get this error.

  Coincidentally, I got a replacement pre + a few days later. So I activated the phone and it continues to show that email address when I go through the process of"premiere". I ran doctor OS, twice. I did the reset/full erase, twice.

  Every time I have "sync" my contacts with my Palm profile, I get this "incorrect password" for the other person's facebook account. Really? Where that little info?

  It isn't on my profile page palm, not in my facebook client, not in my address book...

  I spent a few hours talking with a person well-informed VERY to Palm support. He opened a ticket because he couldn't solve it.

  OK, I have the solution and I must say that I am surprised at the answer (and not in a good way).

  It turns out that synergy will be integrated into the accounts without asking. He sees no difference with an additional e-mail address and someone using their email address to check facebook from my phone.

  Palm note: It is a horrible and dangerous and quite unexpected. It is essential that synergy wonder if I want to do this before you take this step. I had more than 500 new contacts of a person with my phone for 30 seconds. And I got constant actions of backup or automatic and manual synchronization error messages. Nice to wake up to the error messages. This behavior is a bug. Behavior wrong and undocumented. Until fix you this, there should be a label on every new phone that says: 'be careful, never lend this phone to anyone, unless they promise to do nothing more than to make telephone calls'.

  Solution: It is in fact just as crazy as the problem, in my humble OPINION. When someone connects to the facebook app, synergy adds this e-mail account to 4 applications! A reasonable person would assume that a remove the e-mail account of the FaceBook application that would solve. In fact, it was smart enough to delete contacts 500 +, he shot on the unwanted FaceBook account. But imagine that it would also add this account to 3 other applications? Although it adds account 4 apps, it wasn't smart enough to REMOVE IT from these applications.

  Go to more than 3 applications. Photos, address book and calendar. Once you have deleted the email address of these 4 (Yes 4) apps, the problem is resolved. WUH? I had already done. Then I went to a replacement phone, and apparently not all of those changes when this is stated in my Palm profile before I activated the new material. So he put those references into every time I reset or "doctored" the phone. When I re-trace my steps, I found that the e-mail account was back in the calendar, even though I had removed it several times.

  Palm support had me once again, remove it, then run a manual backup. That seemed to make the deletion permanent.

  In the application (at the top left of the screen) menu, choose 'Preferences and accounts' to remove the rogue e-mail account. Delete this email account in FaceBook, Photos, address book and calendar.

  I don't have the courage to let someone try it with other guests of the social network, MySpace, or Twitter, but I hope that they behave in the same way.

  Moreover, Palm support this increased rapidly and has been VERY helpful to understand this. It took them a while to understand it, but they kept the call and try things until they got it. I'm surprised, it was not documented somewhere, but I'm really impressed by how much they knew. They did a great job! Kudos to Palm support!

  I hope this helps others, and I hope fixes Palm synergy runaway nature and provides a more granular control on what she accompanied...

• APEX 5 - page partial refresh of specific IR refreshing all IR regions when they are in a "main" region

  I created a page with several interactive reports. The main report at the top is a report of "companies". All other reports are partial reports (addresses, Contacts, etc.). I have a page that I put the value with javascript (company code) by clicking on a line from 'Companies' parent report. I have a dynamic action on the change of the page element, which then updates from subreports in society, they have chosen. When interactive reports are not in a region, it works very well. When I try to put them all inside a region main standard HTML page/visual layout purposes, they do not work and looks like it is refreshing to all reports (including the main ' firms' one). When I separate everything out of the main area, they all work very well yet. All subreports have a condition in the SQL query to limit the rows in the place where company_id =: P2_COMPANY_ID. The ir companies, does not have this condition. Right now, I just them removed from the main area, but I wonder if it is a bug.

  Hi Jen,

  We agree it shouldn't / desired behavior and filed bug #21207953 for what should be fixed in the first series of patch 5.0.1.

  During this time, John has proposed the following solution for me, which just is to reorganize a little, your regions such as the IRs child are not direct descendants of the parent IR so maybe you have something like this:

  IRR1

  IRR2

  IRR3

  That could be changed to:

  R1

  IRR1

  R2

  IRR2

  IRR3

  Where R1 and R2 use models of simple region (for example 'white with attributes' the universal theme) which show nothing visually on your page, and because they are no longer the direct descendants of level higher IRR, prevent you unwanted refreshment.

  Kind regards

  Anthony.

• SelectionListener ADF table fault line did not

  Hi all

  I came across this well-known problem:

  SelectionListener not firing when only 1 result of searching in a table

  SelectionListener ADF table question

  Listener First Row af selection problem: table in ADF 11 g | _outwardBound

  Basically the selectionListener on the table of the ADF is not triggered for the selected standard line, or if the table has only one line, when you filter a column and the result returns only a single line or even when you turn off the filters and it shows you once again all the lines, marking the first such as selected.

  To summarize, the selectionListener is launched when the user clicks on a different line, but not from the default (even if the user clicks on it on purpose).

  I know that there are a few workarrounds, but who may not be suitable for the use of each case on these old threads.

  I think that, given that the line is selected (does'nt matter whether or not it is by default), the developers expect the listener to be pulled in all cases and that this behavior is a bug.

  My question is, given that this problem is still happening in jdev 12.1.3, if there are plans to fix this in future versions.

  Thank you.

  We cannot answer that. To get a response, you must file an SR with support.oracle.com and seek support for a date it a fix.

  Timo

• Creating a package includes all actions in a module when referencing only the module.

  I don't know if this is a bug or not, but I thought I'd ask the question here.  I'm trying to adjust my coding to match suggestions in the guide so I try to reduce my System.getModule calls.  It seems that the module does not get included in a package, if I put a variable in a task scriptable for just the module or if I put an attribute to the module.  I expect the compiler to package to capture the entire module and include it in the package when I do, but that does not happen.  It is expected behavior, or a bug?  Looks like a bug to me.

  This is the expected behavior of the present code, although it could also be considered a bug.

  The code that scans the content of script to determine what elements are referenced scans for a System.getModule("someModuleName").someAction (args) of criteria special and, if found, adds someAction action to the package. It does not detect the model of System.getModule ("someModuleName") and therefore does not add all the actions of this module to the package.

  It also means that the outline does not detect someAction as being referenced:

  var module = System.getModule ("someModuleName");

  module.someAction (args);

  The problem is that the reference scanner is not a good Javascript language parser and does not recognize the many valid Javascript constructions.

• Problem: by dropping a Table Check constraint

  I got a check from a table constraint in my model. Then wanted to synchronize data dictionary. The comparison of models- dialogue see the difference, but as I check the box drop -(which is unchecked by default) and click the DOF preview preview is empty. I mean it's totally empty, not even the ddl-comments standard as

  -Generated by Oracle SQL Developer Data Modeler 4.0.1.836

  show up! So I guess that this behavior as a bug.

  Dieter

  Hi Dieter,

  Thanks for reporting this problem.  I connected a bug on this issue.

  Note that this problem does not occur for check constraints that are defined in the definition of a column.   It only occurs to verify the constraints defined at the Table level.

  David

• Do not focus on type maps

  When I create a map that contains centered text it appears only focus after using the button. but when you first launch the whole text is top RAS.

  Can understand why?

  Here is the image of the card settings:

  

  Here is a a picture of text as it appears first before and after click on:

  

  

  Your sounds of behavior as a bug and not related to the way that you put cards in place. I spent along the dev team to investigate.

• OQL + Member distributed with the REPLICATE_PROXY regions

  Hello

  We have defined two caches. That contains the data and SAID regions and another that acts as a gateway with the REPLICATE_PROXY regions.

  The problem now comes with the client (used applications) linking well Locator. Sometimes the request goes to the bridge (with the REPLICATED_PROXY regions) memebr and receive all the data of the Member. Of course because he has no data and is the only PROXY. However according to documentations should work:

  REPLICATE_PROXY
  A REPLICATE_PROXY has no local State and transmits all operations to an ADAPTATION or a REPLICATE_PERSISTENT who are his peers.

  But not like all operations covers the OQL as well. Select * FROM /MYREGION.

  (a) what is the expected behavior or a bug?

  (b) how can we prevent a customer form does not connect to this specific Member? cache-server-port does not work as it is just a work around and we have paritioned area mixed with replicated regions, so do not specify a port?

  (c) also set level is-server cache = "false" doesn't work? What is the use of this tag. The default value is 'false' anyway.

  This looks like a bug, based at least on what documentation and of the observed behavior.

  Because you don't want this node to a cache server, is that you want not clients can connect to it, you can start this node without the server component that listens for client connections. If you use the cacheserver script to start your cache nodes, you can set the parameter - disable-server-default to achieve. If you have GemFire 7.0 and use gfsh to start your nodes, 'start server' command has the same setting.