Brocade 8 Gb FC Dual-port HBA for IBM (46M 6050)

Similar Questions

• Mac Pro 3.1 dual port USB 3 pci-e card does not work on 10.8

  I have an inateck Dual Port USB 3.0 PCI-E card (KTU3FR - 2 p) which worked well when my Mac Pro 3.1 operated in the OS10.6.8, but after upgrade to OS 10.8.5, the map is no longer operational.   It can be seen as a device, but the description of the material says that he doesn't have a driver.  Inateck said it's Apple area, and "because of the new strategy of the Apple driver there is also no external support pilot in this case.  Can I do other than throw the card?

  THX

  Rob

  If inateck doesn't have drivers for OSX 10.8, and 3 Apple USB drivers do not work, then you are out of luck

• Model a block synchronous dual-port RAM with LabVIEW FPGA

  This question caught my attention recently.

  I am trying to model a particular design element called "RAMB4_S8_S8" with the LabVIEW FPGA module. This element is a block synchronous dual-port RAM allowing simultaneous access to two ports independently from each other. That being said, a port can perform read/write operation to this RAM while at the same time, the other port might be able to do the same thing. There are two opportunities of possible port conflict, however. The first is when both ports are trying to write to the same memory cell. The other scenario is when a port writes in a cell memory while at the same time the other port reads from it. Other than that, everything should be a legitimate operation.

  In order to reproduce this I select memory block that is integrated into my FPGA target. An interface is configured to be the playback mode, and the other is set to write fashion. For the option of arbitration, I let the two interfaces to be "arbitrate if several applicants only. Then I got a compiler error when I tried to run my FPGA code for this model in a SCTL. The error message is something like "several objects to request access to a resource through a resource configured with option interface" arbitrate if several applicants only ", which is supported only in the single-cycle Timed loop if there is only a single applicant by interface.

  This error goes away if I replace the SCTL with a simple while loop, but not what I would like to implement. So I wonder if there is a better solution to this problem, or is it just the limitation of the LabVIEW FPGA module.

  Thank you.

  Yes, you can use a form of conduct to perform the operations you want in the generations clock cycles, but all the code is inside a single SCTL. Basically, read the first address and storing in a register in a single cycle and then read the second address in the second clock cycle. This would allow you to two readings of valid memory every clock cycle 2. I have included a crude extract to illustrate the concept. The case selectors are identical with address A being connected to the memory in the true case, B in the case of fake address. Your biggest model memory dual port will be intact, but it will operate at 1/2 rate.

  Take a look at the white paper that provides more details on the construction of memory:

  Data on a target FPGAS (FPGA Module)

  The ball on the memory block indicates that memory block double port cannot be applied in a configuration of reading, which is a double ROM. access read/write port must be imitated with custom code.

• R.620 with two INTEL X 520 Dual Port 10 GB DA / SFP +.

  We have R620s running for our VMware ESXi environment. Currently, each server has an Intel x 520 with sfp + ports 10 GB (2) and (2) gig ethernet ports. Each server also has a Broadcom 4 gig ethernet card port. Can I exchange the Broadcom card on each server with a different Intel x 520, so that each server has ports sfp + 10 GB (4) and (4) gig ethernet ports?

  Thank you.

  Hello

  jmartinich

  Ports sfp + 10 GB Intel x 520 with (2) and (2), gig ethernet ports

  Which resembles the daughterboard X 520/I350 network. You have only a NDC slot in the system, only one of those can take place. I do not show a similar adapter PCIe version.

  If you have 2 PCIe 3 slot CPU configuration while you might add just another X 520 dual port. If you have a PCIe 2 connector configuration so I am not all ports that you are wanting to get a valid population.

  Thank you

• HP ZBook 17: Only one Dual Port EC2000S (RTL8111E, r8169) ExpressCard Port detected

  IK have the problem of this network only a Port Dual Port ExpressCard, StarTech EC2000S (RTL8111E, r8169) is detected.

  The problem occurres in Windows-7 and Fedora linux. (The system is dual-boot).

  I have updated BIOS updated to the latest version 01.33.

  The same card is ok in a HP's Probook 4720.

  Who can help?

  The Startech EC2000S dual port network adapter does not have Word with systems of cpu with Haswell as with the Ivy Bridge chips.

  There is therefore no sulution for this problem.

• Cannot send/receive at full speed with Intel dual port 10 GIG 82599 ethernet in guest on ESXi 5.5 OS

  Me to consider whether or not it is possible to send/receive to 20 Gbps throughput with Intel 82599 dual port card within a guest VM on ESXi. I use to send and receive traffic PF_RING DNA of ntop. I have configured the dual-port card Direct IO mode to allow the guest VM have a direct access to the card. For the traffic generator, I use a metal machine naked with another dual port ethernet to generate traffic. The generator of nu metal machine and ESXi have their double ethernet port directly connected via SPF + cables.

  In the first experiment, the traffic generator generates 10 Gbps of traffic on port 1. The guest VM is able to capture packets at full speed without any loss of package even for 64 byte packets, which translates into 14mil PPS. I had then invited VM pass to 10 Gbps for the traffic generator, which currently receives. However, guest VM was able to generate about 7 Gbps of traffic regardless of package size. The CPU seems to be fine at around only 20% of load. I do not understand why the VM can receive at full speed but could not pass to the line rate.

  In the second experiment, the traffic generator generates 20 Gbps of traffic on ports 2. The guest VM unfortunately can only capture at the rate of 5 to 6 Gbps per port for a total of 10-12 Gbit / s. I have the receiving process listens on each port on a different processor. Then, I got VM generate 10 Gbit/s on each port. Unfortunately, could not reach 5 to 6 Gbps per port, regardless of package size.

  The naked metal machine is only an AMD 2.2 ghz machine low range to four hearts. It can send full line ate 10 Gbps for gpbs port 1 and 20 for 2 ports. The ESXi server is actually a much beefier machine with the quad core Intel Xeon 3.2 Ghz. There is a lot of memory and CPU on ESXi machine.

  5.5 runs the ESXi server. I have 1 comments running virtual machine running experience.

  I'm quite puzzled why there is no bottleneck even in Direct IO mode. Both CPU memory seem to be good. I wonder if there is any setting that I need to be playing with in ESXi. I appreciate all help. Thanks in advance.

  It turned out that I placed the network card in the pci slot 3 which is only x 4 routing. I moved it to 1 (x 8) slot. Now, I get full 20 GIG.

• Cannot send/receive at full speed with Intel dual port 10 GIG ethernet in ESXi 5.5 82599

  Me to consider whether or not it is possible to send/receive to 20 Gbps throughput with Intel 82599 dual port card within a guest VM on ESXi. I use to send and receive traffic PF_RING DNA of ntop. I have configured the dual-port card Direct IO mode to allow the guest VM have a direct access to the card. For the traffic generator, I use a metal machine naked with another dual port ethernet to generate traffic. The generator of nu metal machine and ESXi have their double ethernet port directly connected via SPF + cables.

  In the first experiment, the traffic generator generates 10 Gbps of traffic on port 1. The guest VM is able to capture packets at full speed without any loss of package even for 64 byte packets, which translates into 14mil PPS. I had then invited VM pass to 10 Gbps for the traffic generator, which currently receives. However, guest VM was able to generate about 7 Gbps of traffic regardless of package size. The CPU seems to be fine at around only 20% of load. I do not understand why the VM can receive at full speed but could not pass to the line rate.

  In the second experiment, the traffic generator generates 20 Gbps of traffic on ports 2. The guest VM unfortunately can only capture at the rate of 5 to 6 Gbps per port for a total of 10-12 Gbit / s. I have the receiving process listens on each port on a different processor. Then, I got VM generate 10 Gbit/s on each port. Unfortunately, could not reach 5 to 6 Gbps per port, regardless of package size.

  The naked metal machine is only an AMD 2.2 ghz machine low range to four hearts. It can send full line ate 10 Gbps for gpbs port 1 and 20 for 2 ports. The ESXi server is actually a much beefier machine with the quad core Intel Xeon 3.2 Ghz. There is a lot of memory and CPU on ESXi machine.

  5.5 runs the ESXi server. I have 1 comments running virtual machine running experience.

  I'm quite puzzled why there is no bottleneck even in Direct IO mode. Both CPU memory seem to be good. I wonder if there is any setting that I need to be playing with in ESXi. I appreciate all help. Thanks in advance.

  It turned out that I placed the network card in the pci slot 3 which is only x 4 routing. I moved it to 1 (x 8) slot. Now, I get full 20 GIG.

• ESX4i IBM 46M 1076, Dual Port 1 Gb Ethernet daughter card

  Hi guys and girls,

  I recently bought an IBM x 3650 m2 and bought the additional Dual port 1 Gb Ethernet daughter card so I have 4 cards in total.

  I just installed upgrading ESX4i 1 and everything works fine apart it has not detected the 46M 1076, Dual Port 1 Gb Ethernet Daughter Card.

  I can see network adapter Broadcom NetXtreme II BCM5709 that I know are network adapters shipped as I have the configured and connected to the management through vmnic0 port. I can also see vmnic1 which is the other NIC onboard.

  Any ideas on the question of whether the daughter card is supported, and why I can't see it?

  Thanks in advance

  See you soon

  Oli

  Hello

  This ibm network adapter is not supported by vmware.

  You can see in the "IO Devices" of the vmware Compatibility Guide:

  http://www.VMware.com/resources/compatibility/search.php

  A saludo/best regards,.

  Pablo

  If you found this information useful, please consider awarding points for the answers 'OK' or 'useful '. Thank you!! -Como so upon mi respuesta ayuda, por favor puntuarla considered correcta o util. MUCHAS gracias!

• Need new ports USB for Satellite Pro L450D

  Hello

  I ve tried to keep new ports usb for my Toshiba Satellite Pro L450D I ve called Toshiba and they said I have to put it in for repair, but the thing is - it's not is no longer in warranty so that I can t make and send to Toshiba for repair.

  for me would cost loads I ve asked Toshiba provide me for my laptop usb ports, but they won t so I would like to know where I can get these parts as one of my ports usb don t work because of my daughter in the first place to break them and the entire interior of the usb ports is broken.

  Help, please
  Thank you

  Hello

  At first, I must say that Toshiba service doesn t sell these small parts such as USB ports. USB ports are soldered to the motherboard.
  Where to get the new USB ports? Good question.

  I don t know where you MFL, but perhaps you should I use Google in your country and check if you can find some independent repairer for laptop and ask for help.
  I fear it won't be so easy to find new ports of m.

  What you can try is to buy defective mainboard in the hope of USB ports are OK and are trying to replace them.

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team

• HP Compaq 6000 Pro AIO: PCI Serial Port driver for HP Compaq 6000 Pro

  Hello world

  I could get help to find driver serial port PCI for HP Compaq 6000 Pro all in one workstation. It has 8.1 Windows x 64 installed. The hardware IDS are

  PCI\VEN_8086 & DEV_2E17 & SUBSYS_1489103C & REV_03
  PCI\VEN_8086 & DEV_2E17 & SUBSYS_1489103C
  PCI\VEN_8086 & DEV_2E17 & CC_070002
  PCI\VEN_8086 & DEV_2E17 & CC_0700

  Thank you

  Vignesh

  Hello:

  You need this driver... Install manually if auto installation does not work.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4210069&swItemId=vc_85050_1&swEnvOid=4059

  You can see on the partial copy and paste installation information file driver that the ID you have posted is supported by this driver.

  ; Drivers
  ;----------------------------------------------------------
  [Manufacturer]
  Intel % = Intel, NTamd64

  [Intel.NTamd64]
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E07 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E17 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E27 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E37 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E97 & CC_0700"

• I use a server DNS Server 2008 and need to transmit the DNS lookup on a Linux server that only allows you to Port 3128 for DNS.

  Hello

  I use a server DNS Server 2008 and need to transmit the DNS lookup on a Linux server that only allows you to Port 3128 for DNS.

  How can I configure my DNS server to use this port for shipments?

  Thanks for your replies

  Marcus

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  http://social.technet.Microsoft.com/forums/en-us/winserverNIS/threads
   
  Here are a few Server DNS forwarders. Links for refrence,
   
  http://TechNet.Microsoft.com/en-us/library/cc754941.aspx
   
  http://TechNet.Microsoft.com/en-us/library/cc731991.aspx
   
  I hope this helps.

• on port 162 java.exe running. I tried to kill him with the command prodess k 1289. 1298 here is the process ID. but it comes back again. I need the port 162 for sending traps.

  original title: port162

  Hi, on port 162 there is a process called java.exe running. I tried to kill him with the command prodess k 1289. 1298 here is the process ID. but it comes back again. I need the port 162 for sending traps. I first removed java completely from my pc, but still there was this java.exe. in fact, there are two java.exe if I check in the running task manager. need help. I also ran antivirus as well as anti-malware software, but no difference.

  Hello

  I suggest you to visit these links and check if it helps:
  http://www.Java.com/en/download/uninstall.jsp
  http://Java.com/en/download/help/regkey_addremove.XML

  Have you tried to change the port to Java? See this link:

  http://www.Java.com/en/download/help/proxy_setup.XML

  It will be useful.

• How to configure Intel X 520 Dual Port card on VMware

  Hello

  I'm Hyeonjin.

  I'm configuration use VMware5.5.

  I want to use Intel X 520 Dual Port SFP + 10 GB as LOM (onboard NIC 1 G TX),

  but is not show the card MMIC Port and NIC set VMware

  How to set up the problem?

  Server: UCS C220 M4

  CPU: 2.4GZ * 2, Mem: 32 GB, HARD disk: 300 GB * 6

  On board NIC * 2, Intel X 520 SFP + Dual Port 10 GB

  x520.PNG

  

  Those who appear to be 3rd party and are not optical Intel.  Even Cisco SR optics do not work with this card.

  http://www.Intel.com/content/www/us/en/Ethernet-products/optics-cables/Ethernet-SFP-optics-brief.html

  Above link: "Note: other brands of optical modules SFP + will not work with the Intel® Ethernet Server Adapter X 520 series.»

  I recommend you get the specific ones screaming in the technical guide, that those who have been tested and work. (Intel SFP nde2-SFP-1WLR or nde2-SFP-1WSR).

  Thank you

  Kirk...

• count the number of targets, devices and paths by hba for each host with powercli 5.5

  Hi all

  I'm writing this Question again in the community, was not able to found the answer I was looking for in the nets:

  https://communities.VMware.com/thread/516226?start=0 & tstart = 0

  https://communities.VMware.com/thread/293531

  I went through the scripts provided in the community, but seems that t not work on powercli 5.5.

  ///

  # The target account, devices and paths for each host

  Get-Cluster $cluster | Get-VMHost | Sort-Object-property name. {ForEach-Object

  $VMHost = $_

  $VMHost | Get-VMHostHba-type FibreChannel | Sort-Object-property device | {ForEach-Object

  $VMHostHba = $_

  $ScsiLun = $VMHostHba | Get-ScsiLun

  If {($ScsiLun)

  $ScsiLunPath = $ScsiLun | Get-ScsiLunPath | `

  Where-Object {$_.} Name - like "$($VMHostHba.Device) *"} ".

  $Targets = ($ScsiLunPath |) »

  Group-object - property SanID | Measure - Object). County

  $Devices = ($ScsiLun |) Measure - Object). County

  $Paths = ($ScsiLunPath |) Measure - Object). County

  }

  Else {}

  $Targets = 0

  $Devices = 0

  $Paths = 0

  }

  $Report = "" | Select-Object - property VMHost, HBA, target devices, paths

  $Report.VMHost = $VMHost.Name

  $Report.HBA = $VMHostHba.Device

  $Report.Targets = $Targets

  $Report.Devices = $Devices

  $Report.Paths = $Paths

  $Report

  }

  }

  ///

  I went through the script LucD posted below: but it's not exactly what I'm looking for.

  LucD : can you please change the same for me please.   to count the number of paths per hba for each host with powercli 5.5, devices and targets.

  //

  $esx = get-VMHost < host name >

  foreach ($hba to (VMHostHba Get - VMHost $esx - type "FibreChannel")) {}

  $target = ((get - see $hba. VMhost). Config.StorageDevice.ScsiTopology.Adapter | where {$_.} Adapter - eq $hba. Key}). Goal

  $luns = get-ScsiLun - Hba $hba - LunType 'disk '.

  $nrPaths = ($target | % {$_.}) Lun.Count} | Measure - Object - sum). Sum

  Write-Host $hba. Device ' target: ' $target. County "devices:" $luns. County ' path: ' $nrPaths

  }

  //

  I'll be grateful for any help.

  Tarun Gupta

  Try something like this

  {foreach ($esx in Get-VMHost)

  foreach ($hba to (VMHostHba Get - VMHost $esx - type "FibreChannel")) {}

  $target = ((get - see $hba. VMhost). Config.StorageDevice.ScsiTopology.Adapter | where {$_.} Adapter - eq $hba. Key}). Goal

  $luns = get-ScsiLun - Hba $hba - LunType "disk" - ErrorAction SilentlyContinue

  $nrPaths = ($target | % {$_.}) Lun.Count} | Measure - Object - sum). Sum

  $props [ordered] = @ {}

  VMHost = $esx.name

  HBA = $hba. Name

  Target = $target. County

  Device = $luns. County

  Path = $nrPaths

  }

  New-object PSObject-property $props

  }

  }