Portege R830-10V - connection UMTS falls down very often

Similar Questions

• Portege R830-10v / i7 / change internal SSD 225 GB

  Hello

  I need to change my flash drive SSD internal 225 GB for a 512 GB SSD!

  What should I do to the hardware and software level?
  Can I take any SSD?

  Thanks for the help?

  Best regards, Florence

  The HDD or SSD drive update requires no special modifications in the software or hardware.
  You need a compatible player SATA SSD 2.5.

  Here is a nice and very useful document how to upgrade / replace the Portege R830 & Satellite R830 series SSD or HARD disk drive.

  http://APS2.toshiba-tro.de/KB0/CRU18037E0000R01.htm

  Of course, after this upgrade, you'll need to install the system new the best choice would be its use or recovery disk and recover the laptop to factory settings.

• Portege R830 cannot connect iPhone4S to USB port

  Hello world

  I have 5 Portege R830-138 with Win7x64 nine completely updated with the latest drivers and patches.
  Yesterday I connected my iPhone4S to the USB port on the right side and everything worked well (iTunes, tie, etc.).

  Unfortunately, this (the one on the right side) USB port no longer works for today: iPhone, mouse usb pendrives... nothing, it seems to be dead. The USB port on the left side still works with mouse usb and memories but not with the iPhone.

  I thought it was a problem of HW laptop on the right side USB port so I tried with a second Portege.
  Same problem: plug the iPhone on the right side, USB port, the USB port is not working.

  The same iPhone connected to my MacBook Air works fine.
  I wouldn't try with a third Portege, do you have any ideas?

  Thank you
  Valerio

  Hello

  The left USB port supports the standard USB 2.0 USB port on the right standard supports USB 3.0.

  I don't know if the Apple software supports USB 3.0 m.
  According to some information in the internet, USB 3.0 is not supported by Apple

• BlackBerry Smartphones "BOLD" falls down too often

  Hello

  I had this problem for some time. I don't remember if my phone used to hang when I bought first, but I think that this problem came later that I started using it.

  My OS version is: v5.0.0.400 (I think it was later) and platform (5.1.0.110)

  I noticed that my phone often crash when I use the browser on the phone, ex: while on facebook, it crashes just randomly and also when I use the facebook for blackberry application. It's only when I play these two tasks that my phone freezes. My phone carrier is SFR (france). When I say it crashes, I mean it hangs for one or two seconds, the screen turns white and then followed by the light. then it just restarts.

  Memory status:

  FreeSpace: 75.8 MB

  MediaCard freespace: 1.7 GB. (don't have a lot of things on my phone, I made also the memory thing cleaning but it did not help).

  I read through other similar forums but couldn't find a solution. I also tried to uninstall the fb app but the browser of the problem still there. Also it does not matter if my wifi is enabled or disabled, the phone falls down again.

  Someone could suggest a solution to this, and also why this happens only with the browser and fb app?

  First of all, this isn't the latest version of the operating system for the 9700. I know you can get OS 6, if you wish. Don't know if your carrier offers it yet or not, but many are.

  I'm going to guess that the particular operating system you are using has a problem. Try to get a new one and installing it.

• Portege R830-10V - DVD drive makes strange noises

  Hi all
  I just bought this machine and registered the following question:

  If I put in a portable DVD starts very strong buzz. This noise disappears if I put a finger on the reader. In addition, the DVD player starts to chat if I press the keys above the player as the arrow keys. Bothers me a lot.

  I called Toshiba support and they said that they can pick up the laptop. But it is possible that this service costs because maybe this problem is part of the specification.

  You have any ideas? What can I do?
  Best regards
  Denis

  Hi Denis_3,

  Have you noticed this problem with different CD and DVD or just a medium? In General, I also noticed the same behavior, but sometimes just with one disk, so the problem is the drive itself in most cases.

  On this path through the forum it s is not easy to say what the reason is but if it s associated with CD/DVD player and the reader needs replace it will cost you nothing because it s during the warranty. Of course, for out of warranty repairs, you must make ;)

• Portege R830-10V P/N: PT321E AHCI Driver for Win XP 32 bit

  Hello

  I'm looking for driver AHCI Inter chipset 6 series 32bi Win XP. I can't find any work. Tried drivers from toshiba web, I tried web drivers of intel - was trying to google for 4 hours in 2 men. His does not work.

  I can't have win 7 on it, because I have Windows NT 4.0 Domain control and Win 7 does not work.

  So, its simple, I have Windows XP installed with all the AHCI drivers.

  What do you im? Force just install driver AHCI (in the hardware Manager)-online BSOD appears, badly restarts, get bios and change the Compatible in AHCI. I got BSOD again, error is unaccesible by car or something like that so I don't know, I have bad driver. Should I change compatible and try a different driver. I tried this way, all the drivers package from toshiba support web and other Google.

  I had a call with the help of toshiba authorized and that they cannot help me, because they do not know.

  Please, can you, someone help me?

  Thank you.

  Perhaps this Toshiba HowTo might be useful for you
  [How to integrate the AHCI driver when installing Windows XP | http://aps2.toshiba-tro.de/kb0/HTD9401AN0000R01.htm]

• Trial Portege R830 - 10V Bluetooth drivers 30 days

  Hi all

  I own a copy of Windows 7 ultimate.

  So I reinstalled my new laptop to this more advanced version of Windows.
  Now, I just realized that my Bluetooth software that I downloaded from the Toshiba site, is only a 30 day trial version.

  I chose the wrong driver or I buy it?

  Best regards
  Denis

  Hi mate

  BT stack driver is not limited to users who have installed it and use it on Toshiba laptops.
  Check this document:
  http://APS2.toshiba-tro.de/KB0/FAQ81021V0000R01.htm

  + If you use a non Toshiba Bluetooth adapter (a "dongle" USB or card PC Bluetooth, for example), the adapter may stop working and the following message may appear: +.
  + "Bluetooth Manager: thank your for the evaluation of battery Bluetooth for Windows by Toshiba." The evaluation period has expired. You can purchase a license for this version of Bluetooth Stack for Windows by Toshiba. " +
  + This message is intended for third-party developers of Bluetooth adapters, but may appear if you use such an adapter with the Toshiba Bluetooth Stack - rather than with the stack of the manufacturer of the adapter. The third-party Bluetooth adapter can operate with the battery Toshiba Bluetooth, but only for a 30 days evaluation period. +
  + For your Bluetooth adapter is working again, you must install the battery correct Bluetooth from the manufacturer of the Bluetooth adapter. +

  I found this here on this Toshiba BT Portal
  http://APS2.toshiba-tro.de/Bluetooth/

• Portege R830-10V - how to get press PRTSCN to work? (PRTSC)

  Help, please. I'm new on the Toshiba. My print screen button does nothing and I need to use it every day.

  Thank you, Brenda

  Brenda Hay

  Sorry but I don't understand what you mean exactly.
  Maybe stupid question now, but what should happen when you use the button PRTSC?

• VPN falls down intermettenly to one or more locations

  Hello

  We are facing a major challenge of the VPN tunnel down very often. It works very well for a few days, got 7 connectivity VPN Site-2-Site VPN tunnel suddenly breaks down intermettenly for one or a few places and I need to erase isakmp sa to this tunnel specific to come.

  When the tunnel down the status of the phase 1 VPN...

  6 IKE peers: 125.18.0.38

  Type: L2L role: initiator

  Generate a new key: Yes State: MM_ACTIVE_REKEY

  7 peer IKE: 125.18.0.38

  Type: L2L role: answering machine

  Generate a new key: no State: MM_REKEY_DONE_H2

  After clearing the phase 1 for specific tunnel the VPN tunnel developed.

  7 peer IKE: 125.18.0.38
  Type: L2L role: answering machine
  Generate a new key: no State: MM_ACTIVE

  CINBLR01-SQDR-FIREWALL-00002 # sh version

  Cisco Adaptive Security Appliance Software Version 8.0 (4)
  Version 6.1 Device Manager (5)

  Updated Friday August 7 08 20:53 by manufacturers
  System image file is "disk0: / asa804 - k8.bin.
  The configuration file to the startup was "startup-config '.

  CINBLR01-SQDR-FIREWALL-00002 to 1 day 17 hours

  Material: ASA5510-K8, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz
  Internal ATA Compact Flash, 256 MB
  BIOS Flash M50FW080 @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
  Start firmware: CN1000-MC-BOOT - 2.00
  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05
  0: Ext: Ethernet0/0: the address is 001b.0c38.d232, irq 9
  1: Ext: Ethernet0/1: the address is 001b.0c38.d233, irq 9
  2: Ext: Ethernet0/2: the address is 001b.0c38.d234, irq 9
  3: Ext: Ethernet0/3: the address is 001b.0c38.d235, irq 9
  4: Ext: Management0/0: the address is 001b.0c38.d231, irq 11
  5: Int: not used: irq 11
  6: Int: not used: irq 5

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 100
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  VPN peers: 250
  WebVPN peers: 2
  AnyConnect for Mobile: disabled
  AnyConnect for Linksys phone: disabled
  Assessment of Advanced endpoint: disabled
  Proxy UC sessions: 2

  This platform includes an ASA 5510 Security Plus license.

  / * Style definitions * / table. MsoNormalTable {mso-style-name: "Table Normal" "; mso-knew-rowband-size: 0; mso-knew-colband-size: 0; mso-style - noshow:yes; mso-style-parent:" ";" mso-padding-alt: 0 to 5.4pt 0 to 5.4pt; mso-para-margin: 0; mso-para-margin-bottom: .0001pt; mso-pagination: widow-orphan; do-size: 10.0pt; do-family: "Times New Roman"; mso-ansi-language: #0400; mso-fareast-language: #0400; mso-bidi-language: #0400 ;} "}

  Please suggest a permanent solution to this...

  Kind regards

  Narendra

  Hello

  Looks like you have pfs enabled in the configuration of the tunnel. Please remove the configuration of pfs.

  Kind regards

  Anisha

  P.S.: Please mark this message as answered if you feel that your request is answered. Note the useful messages.

• Portege R830 had dead blue when the screen connects to wifi or shared internet

  It seemed began as soon as the automatic update from Microsoft on Qualcomm, Atheros, every time when connect to any WIFi, share internet, my portege R830 shows blue screen and the following error message:
  unhandled system_thread_exception (athwb.sys)

  I found that I am not the isolated on the Web site. I tried to remove and stop updates. However, once I connect to the internet, the blue screen comes back.

  Is the problem because of the network adapter? The model is Qualcomm Atheros AR9002WB
  Can solve the problem if I download the new driver of Qualcomm-Atheros site? Or if I replace a new adapter?

  The athwb.sys file belongs to the Atheros wireless driver. Usually placed in C:\Windows\System32\drivers\athwb.sys
  It seems that in your case this file causing the BSOD.

  I found a very interesting detail about this problem and why it seems.

  A user wrote:
  {quote} The issue is due to a database hosted on Linux kernel mapped NAS drives and if the Client for NFS is installed on the windows machine. For some reason, this configuration does not work. If you mount your shares and NFS is installed it tries to use the NFS client and fails miserably. Trick is to disassemble all the shares of logging in Safe Mode and then rebooted and uninstall the NFS client and then mount your shares. {quote}

• Portege R830 - problems of 3G connection after installing Win 7 32 bit

  Hello

  I went down a Portege R830 Windows 7 64 bit for Windows 7 32 bit with drivers of Toshiba. I put a SIM from my provider.
  In the windows Network Manager, 7 and in the Toshiba Wireless Manager I can see the right provider and HSPA network but when I start the connection, it does not (I don't have a PIN code).

  It is failed with Windows 7 Network Manager and Manager Toshiba wireless (I don't have this problem with the Portege R700 windows 7 32bits)

  But I found a small solution (but I think that's not enough):
  I have created a dial-up connection, with a number * 99 #,.
  I started the connection, it does not happen, but after that, when I raise my first connection is good.

  I don't know why, it's as if the modem is in sleep and the dial-up connection wake-up the modem, because after all is good (win7 Network Manager, Manager wireless Toshiba) so if I reboot the Portege.

  I want to avoid the dial-up connection on my r700 portege with 32-bit windows 7

  Thanks for your help and sorry for my English.
  support for the toshiba told me to reinstall windows 7 64 bit to solve the problem :)

  Hello

  Are you sure that you have correctly configured the connection?
  Here is a nice FAQ that explains step by step how to connect 3G using the Toshiba Wireless Manager:

  + How to configure and set up a 3G connection via the preinstalled Toshiba Wireless Manager +.
  http://APS2.toshiba-tro.de/KB0/FAQ1A037W0000R01.htm

  and here you can find instruction how to create dial upward of connection using own configuration of Windows.

  + How to create a Dial-Up connection with 3 +.
  http://APS2.toshiba-tro.de/KB0/HTD9802OF0000R01.htm

  Recommend check them both!

• Portege R830-138 - does not connect to the SharePoint Site: 401.1 error

  Recently bought a Portege R830-138, but I am getting it to connect to our Service businesses - SharePoint Site I receive a "error HTTP 401.1 - Unauthorized: access denied due to credentials not valid." message.
  The laptop has a full internet access and we have access to the server that is running the SharePoint site by using the same credentials via Remote Desktop. Can also connect to SharePoint site of any another machine using the same credentials.
  Services SharePoint runs on a server with OS - Windows Server 2003 Standard Edition with SP2

  The IT support checked this knowledge of MS doc?:
  + You get a "error HTTP 401.1 - Unauthorized: access denied due to credentials not valid" error message when you try to access a Web site that is part of an IIS 6.0 application pool +.
  http://support.Microsoft.com/kb/871179

• How to connect multiple external monitors to Portege R830

  Anyone has any advice on how to connect more than one external monitor to a Portege R830?

  I have a monitor through the station home, but when I attach a second monitor to the port of the laptop do not recognize at all.

  It is used to work on my old Portege, but for some reason not on the R830.

  Any tips or advice?

  Hello

  You use the same port in the docking station and Portege R830?
  Docking station replica ports in order to use the Portege docking station port or port.

  If you want to connect more than one external monitor to the laptop then I would recommend using something like Toshiba Dynadock
  http://us.Toshiba.com/computers/accessories/dynadock/

  Welcome them

• Portege R830-10R: No. USB connection after recovery from sleep mode

  Nice day!

  I have experienced the problem depending on my Portege R830-10R for a long time.

  Quite often, when he recovers as soon as "sleep" mode it loses the ability to recognize USB devices and built-in 3G modem does not work as well.

  After awhile, like 10-15 minutes of work (or), the problem is solved by itself, but normally, it is not the case.

  If I try to send the laptop to Hibernate or "standby mode" again, while this problem is active, allows to say, it not put into hibernation and crashes on a midway with a black screen - so I have to stop it manually, and then start again.

  Normally, the only way to solve the problem is to restart, but the issue comes after the next "standby".

  Someone has something like this? Any solution available?

  Hello

  > Quite frequently, when he recovers as soon as "sleep" mode it loses the ability to recognize USB devices and built-in 3G modem does not work as well.

  Have you noticed this behavior from the first day of purchase?

  Only special USB devices assigned as USB flash memory stick or USB HDD or are
  other devices such as the USB mouse or USB keyboard has also affected?

• Portege R830/PT321E: update the Bios stops with "year error occurred while...» »

  Portege R830/PT321E: update Bios end with ' year error occurred while preparing the environment of update...» »

  Following message appears first

  BIOS version: Worm. current 3.40-> update version 3.70
  THIS Version: worm. current 1.30-> update version 1.50
  BIOS and THIS should be updated

  During BIOS update seems following message:

  + An error occurred during the preparation of the updated environment. You have not given permission to run the update. +

  My settings:
  -BitLocker is turned off.
  -No connection to a docking station
  -Windows 7 is installed
  -Boot mode is enabled? I guess that means:
  "Close all open programs, shut down windows and then turns off your computer."

  Any idea what is the problem?

  Post edited by: ML

  Hi ML

  Stupid question maybe now but why do you want to update the BIOS on this, I think, fairly new laptop model?
  Have you noticed a few issues or hardware issues?