BSOD 0x0000007e blue screen

Similar Questions

• Error 0x0000007e blue screen

  blue screen error at startup

  Only, my computer will boot in safe mode. I get the blue screen with WCC error 0x0000007e (0xc0000005, 0xa48dd184, 0xba502d3c, 0xba502a38) problems began after KB2555917 & KB2507938 updates have been installed.

  Make a bootable CD of XP (no XP media required) Recovery Console.

  Since the XP Recovery Console, you can uninstall updates two you listed, if things look better, you need to run MBAM and SAS, then when they run clean, you can simply reinstall the
  updates.  I would do one at a time and reboot each other to see which one is causing the problem.

  The Microsoft Support engineer should be able to tell how to uninstall updates of the Recovery Console.  Otherwise, I can, but I don't have the time to write because I have to go to work for a good while now, but at least make the XP Recovery CD of Console and get this to work.

  Here's how to make a CD of bootable XP Recovery Console:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  Once you're already once started, follow these steps:

  Update your McAfee and Ad-Aware with the latest definitions.

  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.

• blue screen error page "0x0000007E (0 x 0000005, 0x806E794F, 0xF7A45C30.). 0xF7A4592c).

  I get this error since the 22 and I ran across the typical procedures already (clean the temporary files and updates to the bios, etc.).
  I still keep getting a blue screen error page saying "0x0000007E (0 x 0000005, 0x806E794F, 0xF7A45C30.). 0xF7A4592c).

  The minidump files show a SYSTEM_THREAD_EXCEPTION_NOT_HANDLED_M (1000007e) coherent don't stop error.with no third-party driver named as causing the crash.

  Here is a "Summary" of the accident:

  BUCKET_ID: 0x7E_nt! FsRtlRemovePerStreamContext+ 1

  Here's the "Stack_Text" which refers to the fltmgr.sys:

  STACK_TEXT:
  f7a4dcf4 804ed978 85fdba28 85e185cc 85fdba20 hal! ExAcquireFastMutex + 0xf
  f7a4dd08 f7458b6c e2fa9b30 85e18370 e2fa9b30 nt! FsRtlRemovePerStreamContext + 0x1e
  f7a4dd34 f745a0ba 85e18370 86873be8 85e254c8 fltmgr! FltpDeleteAllStreamListCtrls + 0 x 62
  f7a4dd50 f744c8f7 85e183f4 86873be8 00000008 fltmgr! FltpFreeVolume + 0xa4
  f7a4dd68 f745064e 85e254c8 00000008 8056485c fltmgr! FltpCleanupDeviceObject + 0x61
  f7a4dd7c 805387cb 86873be8 86dc2b30 00000000 fltmgr! FltpFastIoDetachDeviceWorker + 0x14
  f7a4ddac 805cffa8 86873be8 00000000 00000000 nt! ExpWorkerThread + 0xef
  f7a4dddc 8054615e 805386dc 00000000 00000001 nt! PspSystemThreadStartup + 0 x 34
  00000000 00000000 00000000 00000000 00000000 nt! KiThreadStartup + 0x16

  It is very similar to the error reported in the following link where "Drive Letter Access" seems to be the issue.

  http://Forum.sysinternals.com/BSOD-7E-Driver-Verifier-problems_topic18148_page1.html

  Since you also have Sonic Drive Letter Access installed you can try to uninstall this software and see if the problem resolves.

• Error blue screen STOP: 0x0000007e. I powercycled the sys, unable to choose for sure (keys do not work when you try to select a mode) sys is trying just to go back to the blue screen. Help, please

  STOP: 0x0000007e (0xc000001d, ox8537008 0xba4c3508 0xba4c3204) and the system would not come to the top.

  Error blue screen STOP: 0x0000007e. I powercycled the sys, unable to choose for sure (keys do not work when you try to select a mode) sys is trying just to go back to the blue screen. Help, please

  Symptoms: Booted computer, loaded the raid drivers and showed at the start screen XP for half a second then to BSOD with a Stop error Code 0x0000007E - see also a lot of users (0xC0000001D, 0 x-, etc.) as well.

  Solution:

  1 boot from your Windows XP CD and start the recovery console. You may need to press F6 while RC loads in order to load the SATA drivers. you will have a prompt c:\WINDOWS to the console.

  2. type: CD $NtUninstallKB977165$ \spuninst (it's the update, I had to uninstall to get out of the boot loop, other updates can be uninstalled by changing the name of the directory to $NtUninstallKBCODE$, where KBCODE is the code KB)

  3. type: BATCH spuninst.txt

  4. type: exit

  Don't forget to configure your system to boot from the HD before resuming. I hope this helps. Saved me a lot of hassle today.

  -Tom Steele
  http://www.hawkandtom.com Tom Steele

• Error 0x0000007E on normal startup, Mup.sys on SafeMode boot blue screen

  original title: BSOD on normal boot, safe mode startup Mup.sys

  So today, I got 18 updates on my laptop and Microsoft Office. I did both at the same time on both computers and my laptop lights no more.  My office works very well. two of my computers have XP Pro on them.

  If I boot in safe mode it hangs

  multi (0) disk (0) rdisk (0) partition (1) \WINDOWS\System32\Drivers\Mup.sys

  If I boot normally I get a bluescreen with

  Technical information:
  STOP: 0X0000007E (0X805BA6EC, 0XBACCB2B8, 0 X 80000003, 0XBACCAFB4)

  My bios is A05 which is common for a Dell Latitude D810.

  Is there a fix or is dead XP?

  Hello

  You have a Restore Point before this happened?

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  Visit this link before you restore just in case that is your problem.

  http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/276904c0-e775-4AC9-92b3-8abf465f8d4d

  Try a restore of the system to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  -----------------------------------------

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates an unaligned data reference was encountered.
  • 0 x 80000003: STATUS_BREAKPOINT indicates a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.
  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in the directory Inc. of the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system was launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly, make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Ensure that any new hardware that is installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the service by starting the computer by using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved .chk , which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  More information on troubleshooting blue screens below.

  -------------------------------------------------------------

  Stop the automatic driver updates as below - use these methods when you want to update the drivers.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  I hope this helps.

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Unable to start - blue screen STOP: 0X0000007E

  original title: STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578)

  I was working on my laptop Acer Aspire and suddenly my restarted windows and then leave her unable to start and just show a blue screen with the error code as STOP: 0X0000007E (0XC0000005, 0X89B16963, 0X8B76B87C, 0X8B76B578).

  I tried to run in safe mode, then even I tried all the options available in the Advanced menu to restart that we get after pressing F8 but just fails. Repair of the system showed the error Impossible to repair in the same way his unable to restore and unable to start with last successful boot setting.

  Kindly let me know what to do I have lots of important data in my hard drive that I don't want to lose.

  Hello

  Unless the drive itself is completely fried the data on disk can be recovered by putting the hard drive
  in another computer as 2nd or a case of external hard drive using a USB connection - then the data
  likely to be backed up or copied to other media.

  Of course, the major problem is that the system does not boot even in Safe Mode.

  Setup/settings (BIOS/CMOS) often F2 so screen shows that it boots CD/DVD on the 1st in the boot order-
  Start with a Windows 7 disc and try the Startup Repair tool. Also, try restoring the system from there. (Don't forget to)
  Set the boot order to when.)

  Those who cannot not helped at all and will need you the help of a real computer store (no leeks and)
  Displays a BestBuy or other stores) or system manufacturer support.

  =================================================================

  Here are the usual methods to troubleshoot the bluescreens if you have access to some and still have a
  problem.

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top 3 answers.

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  -----------------------------------------------------------------------------------------------------------------

  The system has RAID? If so, it is very suspicious.

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
  interpret, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
  the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
  has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
  Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Make sure all new hardware that is installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable
  or remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
  Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
  in Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the boot of the computer service
  by using the Recovery Console, and then by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You should also
  Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or
  Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
  BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
  space, reduce the number of files on the disk drive hard target. Find and delete any temporary
  the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
  contain fragments of file saved to disk scans. You can also use another hard drive with more drive
  free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="">
  * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-
  -------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard event viewer
  Windows. TIP - Options - Advanced filter allows you to see a time rather
  of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during ' blue screen of the.
  death ' crashes and displays information about all accidents of a table.
  Free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
  However, there are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Does not work
  tell all possible driver issues).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• [SOLVED] ATI HD series random blue screen error: error 0x0000007e ntoskrnl kb965494

  [Problems]

  Fixes random maps of BSOD blue screen of death ATI HD Series - spontaneous different random BSOD error codes every time

  Solves problems with his SoundBlaster X - FI (on board and add the map) extreme gamer - Sound sound seriously jerky or cut sharply off the coast

  Solves delays random system - system shuts down randomly for no apparent reason
  Solves the problems of disconnected Steam - quite noticeable in Call of Duty 4 Modern Warfare 2
  Resolved A of Call of Duty 4 Modern Warfare 2 in delays play random or falling of the game so that your game. Usually, when first start the game. Not having not NAT enable may cause a similar delay as well.
  [Source of problem]
  The problem is with an older driver a new loading equipment when you first load the operating system from Microsoft. Shame on you, Microsoft.  6 weeks to understand it and it is CLEARLY without Microsoft. Sorry, but none of the NDA here.
  Its a simple problem, yet almost impossible to find. Catalyst install Manager - ATI HDMI Audio Device will add an Audio device rather than to replace the device driver Audio HDMI Microsoft load the OS installation stage. Or the pilot is ignored all together because Microsoft has already loaded a driver installation for this device.
  [Clean Install FIX]
  When you install the ATI Catalyst 10.6, use the custom installation and exclude the HDMI Audio by unchecking the box next to the HDMI Audio. Pilots still end upward in the ATI Catalyst install directory if you can note the ATI installation path. The problem is that ATI will add an HDMI high definition audio device, DOES not replace the Windows device already loaded. Or may not charge a second device. Whatever it is, it uses the Microsoft device driver.
  Updated driver software with the driver - Microsoft high definition Audio Device driver ATI manually following the instructions below.
  [Windows OS already loaded FIX]
  -Device Manager-
  Manage driver updated using computer-> right click-> appliances-> sound-> right click HDMI high definition Audio Device-> update driver and browse to the directory of ATI (check include subfolders).
  Also noticed the BIOS default settings cause problems of NB and DRAM. Overclocked to mount pressure on the system. Even if I adjusted the settings of the BIOS, I have always many BSOD until I updated the driver for high definition Audio Device from Microsoft with the ATI driver.
  Ubuntu ran without a single question before changes to accommodate the Windows 7 operating system. For some reason any Windows is picky about certain parameters so that Ubuntu 10.04 LTS loads and runs without a single problem.
  I have the logs memory.dmp and mini.dmp. Any help and any help appreciated :D
  After running through the following steps, the problem here is the ntoskrnl.exe causing several bugs (BSODS). Even if it's a problem with Vista, this problem occurs with Windows 7.
  • Event ID: 1001 Source: error checking
    The computer was restarted after a bugcheck.  The bugcheck was: 0x0000007e (0xffffffffc0000005, 0xfffff88000e34294, 0xfffff880031bda18, 0xfffff880031bd280). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 052310-17316-01.

    The computer was restarted after a bugcheck.  The bugcheck was: 0 x 00000109 (0xb3b7465eeb217b7e, 0xfffff80002d18cc0, 0xa3a039d898a4a950, 0 x 0000000000000001). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 052110-23197-01.

  OS: Microsoft Windows 7 Ultimate 64 bit
  Antivirus: Microsoft Windows Security Essentials
  Motherboard: Gigabyte GA-890FXA-UD5
  RAM: 8 GB CORSAIR DDR3 4 GB 1333 MHz CORSAIR TW3X4G1333C9A TWIN

  Video: Diamond ATI Radeon HD5850 1 GB DDR5

  PROCESSOR: AMD X 4 965BE
  HD: Hitachi 1 TB HDE721010SLA330 S/N MS03G16K
  PS: Antec EarthWatt 750W PSU V2.3
  KB: Logitech G15
  Mouse: Razer Deathadder 3.5 G
  Gamepad: Belkin n52te
  First try to solve this problem:
  Fresh OS loaded and BSOD immediately after the restart. Reason or details is unknown because of the immediate reboot without a kernel image. No events logged in Windows event logs with error checking information.
  At ran Windows Update for the current patches. Random BSOD on restart.
  Load the ATI Catalyst 10.4 Suite for Windows 7 (64-bit). Random BSOD on restart.
  Problem again when the system is stopped and started. Chances are THAT BSOD will occur without emptying the core or the mini writing.
  Run the checker - 90% chance of BSOD
  Ran Check Disk - seems to be stuck on stage 4 'verification data file' 57531 63472 processed files. 01:05: PM 05/21/2010 FAIL stopped here 13:44

  Second attempt to solve this problem (low-level format):

  Using Hitachi tools - http://www.hitachigst.com/hdd/support/download.htm Drive Fitness Test - Switch BIOS from AHCI to IDE to access the SATA drive.
  Quick Test results - HDE721010SLA330 successfully completed / Disposition Code = 0x00
  Clear the result of the boot record - 0x00
  Wipe the drive (drive clean takes time for 1 to ~3.5 hours) / 17:07 Media Analysis / 20:20 hours of fact and change the outcome - success 0x00
  
  
  Updated the BIOS with F2 14/05/2010 (CPU compatibility improve)
  Press DELETE to enter BIOS F8 to enter the Q - Flash insert USB Thumb Drive (a drive if no floppy is in system) select the file
  Change the BIOS settings-
  Integrated Peripherals-
  OnChip SATA Type [Native IDE] change on [AHCI]
  (No Option for this) F6 for drivers to be loaded in Pre-os Windows 7 64 bit

  Install Windows 7 Ultimate 64 bit at 21:02 / Installer Reboot 21:14 / end of installation restart 21:18 / finalised result 21:21 - GOOD

  Install the driver USB 3.0 NEC 21:22 - result - GOOD
  Automatic update added KB978601 (pending reboot) and KB979309 - result - GOOD

  Install the network drivers Realtek Lan_win7 - result - GOOD

  Install win7_chipset (installed ATI Catalyst install manager 03.00.0765) 21:30 - result - BSOD KERNEL DUMP RENOWNED MEMORY. DPM at 5212010935PMMEMORY. DMP

  Hitachi configured disk requires reboot (stop for cold start) - 21:37 - result - connected

  Install Microsoft Windows Security Essentials 64 bits 21:43 d/l latest and scan / to 21:49 results - GOOD

  Shutdown - 21:51

  Power - result - GOOD

  Install ATI 10-4_vista64_win7_64_dd_ccc_wdm_enu (taken from the site of AMD ATI) start 21:59 / 22:01 need to restart (close) - result - GOOD

  Windows Installer wants to make changes - C:\window\SysWOW64\msiexec.exe/x {72736F5F-520 d - 472-A - 88 - 7 B 0 ERRRR it went away on its own.} Closing - 22:05 /qn REBOOT = really delete<---- came="" up="" again="" after="" cold="" start.="" think="" it="" had="" something="" to="" do="" with="" ati="" registration="" window.="">

  Install Google Chrome - result - GOOD

  Install Fusion - 2.0.1.117

  Install AMD OverDrive 3.2.1.0439 utility - Enable AMD Smart profiles -.

  Shutdown

  Power - result - GOOD

  Install the G15 - result - GOOD

  Install Windows Ventrilo 3.0.5 x 64-GOOD

  Install the Steam Client

  Install COD4MW2

  Change the settings to save energy for the computer to never sleep.
  22/05/2010
  Install gtalk, gApps
  Up to 08:57 05/22/2010 BSOD Mini dump.
  
  Dmp kernel that is renamed to 5222010857AMMEMORY. DMP

  BSOD more 2s on 2 days.

  Hello

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot the BlueScreens - top two responses.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/8df6485a-50cc-4cdc-BE3E-0f05c7745117

  ===========================================

  The material is highly suspect!

  Since you reformatted and reloaded Windows this indicates that the problem is either material or a
  very basic pilot who has been reloaded - video/display, network/WiFi, sound, possibly 3rd party
  mouse or keyboard, BIOS, chipset and other low level drivers.

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  ------------------------------------------------

  Even if you have some of these here tried a fairly complete convenience store just in case.

  BCCode: 7F 0x0000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in the directoryInc. of the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system was launched with the/nodebug. switch. This problem should occur infrequently. If it occurs repeatedly, make sure that a kernel debugger is connected and the system is booted with theSwitch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Ensure that any new hardware that is installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the service by starting the computer by using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x0000007E<-- read="">
  * 1141.html http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-

  -----------------------------------------------------

  BCCode: 109 0 x 00000109

  Cause

  There are generally three different causes for this bug check:

  1. A driver has deliberately or inadvertently modified kernel of criticism or data code. Microsoft Windows Server 2003 with Service Pack 1 (SP1) and later versions of Windows for computers x 64 do not allow the kernel to be debugged, except through authorized hot patches from Microsoft. For more information, see policy patch for x 64 systems.

  2. A developer tried to set a normal kernel breakpoint using a kernel debugger which was not attached when the system is started. Normal breakpoints (bp) can be defined only if the debugger is attached to the start time. Processor breakpoints (ba) can be defined at any time.

  3. A physical corruption has occurred. For example, the kernel code or data could are stored in memory has failed.

  BCCode: 109 0 x 00000109<-- read="">
  * 1262.html http://www.faultwire.com/solutions-fatal_error/modification-of-System-Code-or-a-Critical-Data-0x00000109-

  --------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Blue Screen of Death. STOP error 0x0000007E + things I've tried.

  A bit of history. I run a MSI 890XM-G65 and the installation manual can be found at http://www.msi.com/service/
  I use a Radeon HD 6870 graphics card.
  A SATA HARD DRIVE.

  So. Since I got the BSOD (the o death blu screen), these are the steps I've tried:
  I started pressing F8 and tried to start a repair. BSOD appears.
  I started pressing F8 and tried "Run with the last configuration that worked", same thing.
  I changed my boot on CD/DVD in BIOS and tried from my Windows install disc, BSOD appears.
  I tried to delete my graphics (Radeon) card and attached monitor to the on-board, BSOD arises.
  I tried to use one of my RAM sticks GSKILL (two, distinct moments by themselves) and tried in different locations. I also borrow a new KINGSTON DDR3 ram friends and tried is separately, BSOD appears at reboot.

  I also went through the manual to make sure that all power cords are plugged in etc.

  The error is:
  STOP error 0x0000007E: SYSTEM_THREAD_EXCEPTION_NOT_ STOP 0x7E error means that a system thread threw an exception that the error handler did not. STOP code 0x0000007E may also display the SYSTEM_THREAD_EXCEPTION_NOT_ «»

  Hello

  References to Vista also apply to Windows 7.

  It's my generic how updates of appropriate driver: (look for the BIOS and driver
  updates.)

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on
  your system. For each driver in the list, additional useful information is displayed:
  load address of the driver, description, version, name of the product, the company that
  created the pilot and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit system Maker as replacements and manufacturer device which are the
  most up-to-date. Control Panel - Device Manager - Display Adapter - write it down
  and complete the model of your video - double click - tab of the driver card-
  Note the version information. Now click on UPdate Driver (this can do nothing
  that MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT it
  will update the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard
  If there are 3rd party with their own software and drivers and the other main device drivers
  you have.

  Now, go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restore)
  and site (Realtek, Intel, Nvidia, ATI, for example) and get the manufacturer and device
  their latest versions. (Look for the system to update the BIOS, Chipset and software updates
  Site of the manufacturer here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN -.
  REBOOT after each installation.

  Always check in the Device Manager - drivers tab to be sure the version you are
  installation actually appears. This is because that some rollback of drivers before the
  later is installed (particularly that audio drivers) so to install a driver - restart
  -check that it is installed and try again if necessary.

  Repeat to the manufacturers - BTW to the device makers DO NOT RUN THEIR
  SCANNER - check manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using
  the above methods is preferable to ensure the latest drivers from the manufacturer of system
  and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  If you update the drivers manually, then it's a good idea to disable driver facilities
  in the updates of Windows, which leaves on Windows updates, but it will not be installed
  pilots who are generally older and cause problems. If updates provides a new
  driver then hide it (right click on it) and then go get new ones manually if
  you want.

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for the)
  Professional, comprehensive and Enterprise edition)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  ==========================================

  Tests of memory intercept all errors such as memory do not match (possible
  even for the Poles that seem identical) and when the faster memory is placed
  in the system behind the slower memory. So it is best to also swap sticks in and out
  to check for those even if all the tests of memory are not a problem.

  To test the RAM here control - run 4 + hours or so.<-- best="">
  www.memtest.org

  For Vista/Windows 7 memory diagnostics tool

  Start - type in the search-> memory box - find top Memory Diagnostics tool
  -Right click - RUN AS follows ADMIN instructions

  Windows Vista: How to scan / test your RAM or memory with Windows Vista
  Memory Diagnostic tool
  http://www.shivaranjan.com/2007/11/01/Windows-Vista-how-to-scan-test-your-RAM-or-memory-with-Windows-Vista-memory-diagnostic-tool/

  How to run the diagnostic tool memory in Windows 7
  http://www.SevenForums.com/tutorials/715-memory-diagnostics-tool.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Satellite T130 (part PST3AE) blue screen BSOD

  This netbook is just out of warranty of 12 months (2 weeks) and does not on Windows 7 with a blue error screen shortly after the connection.

  It won't reinstall from the recovery partition (it blue screens during the installation of the OS) and a test of memory using the test installation of the recovery partition does not indicate an error with memory of the netbook.

  It has always run hot enough, and I barely saw the announcement of service about upgrading the BIOS to provide warning against overheating.

  I wonder if the overheating has damaged the netbook and now, the only use it has is as a paperweight or if I have to spend the money to replace the disc and try reinstalling the operating system.

  I must admit that I expect a better life of a Toshiba product than just 380 - odd days of use and I am considering what action is open to me under the law of consumption.

  Someone else had a similar problem?

  Hello

  I ve got two Toshiba laptops and never had any problems.
  Of course the laptop can always begin a malfunction it is nothing unusual, because the materials can damage all of a sudden.
  The laptop is therefore covered by the warranty.
  Standard warranty is valid for 12 months, but if you sign up on the page of Toshiba notebook you would get additional year.
  However, in my country the retailer warranty covers products (any product it is) always 24 months long.

  Back to your question; BSOD is the result of serious hardware or software problem.
  A higher temperature may affect parts of portable computer s like for example the RAM modules, and this may cause BSOD.
  This happened with my first non-Toshiba Notebook I bought 10 years ago.

  I guess that you are not sure if it s related to the software or hardware so I recommend recover laptop using the recovery disc or HARD drive recovery.
  If the BSOD happen again even if the laptop was found, then you should check the cooling modules. Clean it with a jet of compressed air. Blocked fans can lead to higher temperatures, which leads to BSOD.
  If this is insufficient, the laptop technician must check the hardware.

• Error on blue screen (BSOD) during and after the installation of Windows 7

  I had to reinstall Windows 7 using the recovery partition. When installing I kept getting blue screen errors and even now I still get the BSOD a few minutes. I have no problem in safe mode.

  My laptop is a Satellite C650D - 12 c. I tried to update the BIOS, but I can't do it in safe mode. What should I do next?

  Saved on the HARD drive recovery image is tested so everything should be OK with recovery image installation.
  What you can try is to use the Microsoft installation disc to see if the same thing will happen again.

  If Yes, I'm afraid, you need professional help with this Portable Mr. probably guaranteed so the service guy should check this.

  You created the recovery DVDs?
  BTW: I think that the update of the BIOS is not solution. Recovery facility must operate with this original version of BIOS.

• Chromebook 11 - error blue screen bsod system 895 32. exe how can I get rid of this? screen cannot be deleted.

  Chromebook 11 - error blue screen bsod system 895 32. exe how can I get rid of this? screen cannot be deleted.

  [Moved from Virus & Malware]

  In case you see something similar...

  

  (photo source: https://malwaretips.com/blogs/remove-debug-malware-error-895-system-32-exe-failure-popup/ )

  ... you can normally just use the Task Manager to exit your browser (' end task'), and the pop-up should be gone. Please visit: http://answers.microsoft.com/en-us/protect/forum/protect_other-protect_scanning/potential-malware-blue-screen-with-dialog-box-on/3569bb1b-c05e-4247-98dc-6bf22da581e0

• Windows 7 clean installation Blue Screen of Death (BSoD) on a loop of reboot

  Aloha everyone,
  I did an install customized windows 7 on a new Western Digital 1 TB sata hard drive, which has been formatted, partitioned, scandisk, and a ntfs c drive was created prior to installation.
  The installation ended safely.  I then install my screen reader, Window-Eyes, requiring a reboot.  After the reboot, I started to install critical updates to Windows.  On my fourth update and restarting, I got the blue screen of death, that of some people call a BSoD.  I rebooted and Windows itself restored to a previous state of good, of my just accept the default choice.  Then the rear computer works, but if I stop, restart I get the blue screen of death (BSod) is back, and the loop begins again, i.e. windows restores good condition that works well, until you stop, but on reboot - BSoD is BACK!
  I removed the automatic update option, I disabled ScanDisk, drivers updated, bluetooth devices, deactivated sideshow, etc., without any positive result.  I called Microsoft for assisstance and the technician acted like this isn't a known issue, but he assured me that he could solve the problem.  He took control of my computer remotely and do not tell me anything except that the computer would check and repair any problem on reboot, and if he did does not resolve the problem, I have to remember.  The computer has rebooted without the BSod, but I stopped to check if the loop went, and it is not!  To restart the BSOd was back.  It is to note that if I put the computer to sleep, I get a clean start, but stop, restart or hibernation, I get the blue screen of death (BSoD)!
  It is a Dell Dimension XPS 420 with a intel Q6600 processer, 3 GB of ddr2 memory, which came with OS Vista Home premium 32-bit.  The Vista system, the last time I got a BSoD has been for more than a year.

  After researching this problem on Google, it appears that there is a problem without a solution.
  I ran "which has crashed, you can get:
  http://www.resplendence.com/downloads

  The following accident report:
  Monday, December 21, 2009 23:23:44 your computer crashed
  This was probably caused by the following module:
  Wininit.exe
  Bug check code: 0xF4 (0x3, 0xFFFFFA800573B060, 0xFFFFFA800573B340, 0xFFFFF80002D91240)
  Error:
  CRITICAL_OBJECT_TERMINATION
  Empty the file: C:\Windows\Minidump\122109-16972-01.dmp
  file path: C:\Windows\system32\wininit.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: Application to Windows startup
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Monday, December 21, 2009 20:22:10 crashed your computer
  This was probably caused by the following module:
  Ntoskrnl.exe
  Verification of error code: 0 x 50 (1, 0xFFFFF80002A9300C, 0xFFFFFFFFFFFFFFD0, 0 x 0 x 0)
  Error:
  PAGE_FAULT_IN_NONPAGED_AREA
  Empty the file: C:\Windows\Minidump\122109-33306-01.dmp
  file path: C:\Windows\system32\ntoskrnl.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: NT Kernel System &
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Sunday, December 20, 2009 15:28:42 crashed your computer
  This was probably caused by the following module:
  Ntoskrnl.exe
  Verification of error code: 0 x 50 (1, 0xFFFFF80002ADC00C, 0xFFFFFFFFFFFFFFD0, 0 x 0 x 0)
  Error:
  PAGE_FAULT_IN_NONPAGED_AREA
  Empty the file: C:\Windows\Minidump\122009-17565-01.dmp
  file path: C:\Windows\system32\ntoskrnl.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: NT Kernel System &
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Thursday, December 17, 2009 12:27:45 AM your computer crashed
  This was probably caused by the following module:
  Ntoskrnl.exe
  Verification of error code: 0 x 50 (1, 0xFFFFF80002A9300C, 0xFFFFFFFFFFFFFFD0, 0 x 0 x 0)
  Error:
  PAGE_FAULT_IN_NONPAGED_AREA
  Empty the file: C:\Windows\Minidump\121609-28111-01.dmp
  file path: C:\Windows\system32\ntoskrnl.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: NT Kernel System &
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Monday, December 14, 2009 20:59:21 crashed your computer
  This was probably caused by the following module:
  Wininit.exe
  Bug check code: 0xF4 (0x3, 0xFFFFFA80059A3060, 0xFFFFFA80059A3340, 0xFFFFF80002DC4240)
  Error:
  CRITICAL_OBJECT_TERMINATION
  Empty the file: C:\Windows\Minidump\121409-25506-01.dmp
  file path: C:\Windows\system32\wininit.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: Application to Windows startup
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Sunday, December 13, 2009 02:17:55 your computer crashed
  This was probably caused by the following module:
  Wininit.exe
  Bug check code: 0xF4 (0x3, 0xFFFFFA80058A4060, 0xFFFFFA80058A4340, 0xFFFFF80002D8A240)
  Error:
  CRITICAL_OBJECT_TERMINATION
  Empty the file: C:\Windows\Minidump\121209-24648-01.dmp
  file path: C:\Windows\system32\wininit.exe
  product:
  Microsoft® Windows® operating system
  company:
  Microsoft Corporation
  Description: Application to Windows startup
  The accident took place in a standard Microsoft module. Your system configuration can
  be incorrect, perhaps the culprit may be another driver on your system which cannot
  be identified at this time.
  Conclusion
  6 dumps were found and analysed. Note that it is not always possible to
  assert with certainty whether a reported driver is really responsible for crashing
  your system or that the cause is in another module. However, it is suggested
  looking for updates for the products that these drivers belong to and regularly
  Visit the Windows Update or activate the automatic updates for Windows. In the case of a piece of
  defective material is in trouble, a Google search on the bug control
  Errors, as well as the name of the model and brand of your computer can help you investigate
  This further.
  end of the crash report.
  A side comment:
  Them are 56 reported problems, and none of them have solutions. If I go through each problem report and check for solutions, about 80% of the times I ask myself to send to Microsoft for more information about the problem and I click on send, but I always get the following:
  [Window title]
  Incident reports

  [Main instruction]
  Problem connecting to the Windows error reporting service

  [Content]
  Some of the reports can not be uploaded to the Windows error reporting service. Please try again later.

  [Close] »
  I tried several times with the same result, that is, the details of the problem which has need of Microsoft is not be received.  To this end, the problem will not be found.
  Thanks much for any help.
  Manny
  P.S. I'll never upgrade a Windows operating system.  My recommendation for anyone who is planning to upgrade to Windows 7 is to try first on a dual boot using the free download.  If it works for you, consider yourself lucky and buy the upgrade.  If it does not, then remove Windows 7 and stay with your old system.

  Please check your RAM for errors (use memtest86 + to test). "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• KB9711486 blue screen causing 0x0000007e

  KB9711486 part of the recent automatic updates last Friday (10/16).  XP SP3, INTEL processor.   After the reboot, get a blue screen with the following error message when windows tries to start.
  0x0000007E (0x805c49b8, 0xf7a602b4, 0 x 8000003, 0xf7a5ffb0).  Also impossible to revert to last good configuration.  Get the error "PAGE_FAULT_IN_NONPAGED_AREA).  Requires external to go back to the last good configuration rescue disk.    Given that Microsoft was pressed so many updates (hotfixes about 11 last Friday... and I run autmatic update), it took trial and error to find patch that was causing the problem.  Ignoring this patch at the moment. Lost most of the weekend recovering in activity. Thank you very much.

  Incidentally, now that the PC is working again, getting another error during the operation:
  DSCA.exe - routing of common language of the debugger service Process ID 0x8d4 Thread id (2260) = 0x8d8 (2264).  Anyone idea what all this on and how do I get rid of him?

  I found this and it worked.

  1 boot from your Windows XP or DVD CD and start the recovery console (see this Microsoft Help article at this stage)

  2. type this command: CHDIR $NtUninstallKB971486$ \spuninst

  3. type this command: BATCH spuninst.txt

  4. type this command: exit

• "A problem has been detected and Windows has shut down to prevent damage to your computer"... * STOP: 0x0000007e (0x805c49b8, 0xf7a172b4, 0 x 80000003, 0xf7a16fb0)... blue screen

  Hello!

  For the life of me I can't figure out how to get my machine to boot successfully. Nothing changes when I choose Safe Mode, last known good Configuration, enable VGA Mode, booting, Directory Services Restore Mode or Debug Mode logging.

  It's very stressful, because I'm right smack dab in the Middle a semester at the College. I have most of what I currently need access to supported illuminates... but not quite all :( It is also very reassuring to be able to take care of the school of work away from the library of the University. Yesterday, my computer was working fine... I think that Windows has completed an update, if I can't remember now. As I woke up this morning, I was not able to boot all the way to Windows only once.

  My laptop is a HP Pavilion dv6000 running XP Media Center, and I have not installed new hardware since I bought the machine about 3 years ago.

  Here are more details, where they can help in the diagnosis of my problem:

  • ID of the system board: 30BB
  • Type of processor: Genuine Intel(r) CPU T2250
  • Processor speed: 1730 MHz
  • Total memory: 1024 MB
  • Video memory up to: 128 MB
  • BIOS version: F.06

  Here's the entire message to the blue screen:
  - - - - - - - - - - - - - - - - - - - -
  A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

  Make sure you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

  Check with your hardware vendor for updates to the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select Safe Mode.

  Technical information:

  STOP: 0X0000007E (0X805C49B8, 0XF7A172B4, 0 X 80000003, 0XF7A16FB0)
  - - - - - - - - - - - - - - - - - - - -

  I also learned to a blue screen that says something about "PAGE_FAULT_IN_NONPAGED_AREA". I think that this happens when I try to start safe mode.

  Also, I never did much with computer problems beyond what could be repaired with the restoration of the system... so not being is not able to boot at all me has to stop. Please, I beg you! Help me?!

  With great appreciation for your time,.
  Damaya

  Quick suggestion

  Some HP partition the hard drive. have you tried to type F11 or F12 during startup (before that he go to the option mode start screen)? It might take you for a HP recovery program in that partition (because windows don't be loading not to use that recovery)
  Good luck

• Blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  How to fix blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  These accidents were caused by the corruption of memory (probably a driver).  Run these two tests to check your memory and find which driver is causing the problem.

  If you are overclocking reset all default before running these tests.
  In other words STOP!

  1 - Memtest.

  * Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. "http://www.memtest.org/#downiso"] Memtest86 + - Advanced Memory Diagnostic tool

  * Boot from the CD and let it run at least 5 or 6 passes.

  Remember, anytime Memtest reports errors, it can be bad RAM or a bad motherboard slot.

  Test the sticks individually and if you find a good, test it in all slots.

  Any error is indicative of a memory problem.

  If a well-known stick fails in a slot of motherboard, it's probably the slot.

  http://www.SevenForums.com/tutorials/105647-RAM-test-Memtest86.html

  2. Driver Verifier

  Using Driver Verifier is a dubious proposition. Most of the time it will crash and it will tell you what is the driver. But sometimes it will crash and will not tell you the driver. Sometimes it will crash until you can connect to Windows. If you can't mode without failure, then you will have to resort to editing the registry offline to disable driver verifier.

  I suggest that you first back up your data and make sure you have access to another computer so you can contact us in case of problems. Then do a system restore point (so you can restore the system using the functionality of Vista/Win7 Startup Repair).

  In Windows 7, you can do a startup repair disk by clicking Start... All programs... Maintenance... Create a system - with Windows Vista repair disc, you need to use your drive installation or from the "Repair your computer" option at the top of the Safe Mode menu.

  So, here is the procedure:
  -Go to start and type "auditor" (without the quotes) and press enter
  -Select 'Create a custom settings (for code developers)' and click 'Next '.
  -Select "Select individual settings from the list complete" and click "Next".
  -Select the entire document except for "Low resource Simulation" and click "next".
  -Select "Select driver names from a list", then click "next".
  Select all drivers that are NOT provided by Microsoft, and then click "Next".
  -On the next page, select "Finish".

  Restart the system and wait as he crashed to blue screen. Continue to use your system normally and if you know what are the causes of the crash, do it several times. The objective here is to get the system crash because Driver Verifier is stressing out the drivers. If it is not planted for you, then let it run for at least 36 hours of continuous operation (an estimate on my part).

  If you are unable to Windows because it crashes too early, try safe mode.
  If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.
  http://www.SevenForums.com/tutorials/101379-Driver-Verifier-enable-disable.html

  Further reading
  "http://support.microsoft.com/kb/244617"] using Driver Verifier to identify issues with Windows drivers for users advanced