C20 and SX20 camera cable

Similar Questions

• 8235 PCIe and several cameras

  I have just connected a second camera of Basler (sc640-70gc) to a PCIe-8235.  The problem is that NIMAX sees only one of them, either the original or the newest one.  I tried different ports and cables; doesn't make a difference.  Any suggestions?

  Hello RTA,.

  If you are running Windows 2000 or XP and you use link-local-addressing (the automatic IP address in the 169.254.x.x range) this is an artifact of a gap in the network stack because it does not properly filter the broadcast by network interface traffic when multiple devices have identical configured subnet information (technical explanation long omitted...)

  The good news is that there are many solutions to this problem:

  -Since you are using the PCIe-8235, you can use our High-Performance GigE Vision driver. When it is installed you can then fill all 4 ports together into a single virtual device network card and this has solved the problem because you only have a link-local IP address configured. All 4 ports act as if they are part of a switch and cameras can easily be moved between them. I think that the manual or guide start-up for the 8235 includes documentation on how to do it. All you have to do is to go to the network connections page, select all the 4 network ports, right click and select "bridge connections".

  -Another option is to assign manual IP addresses in different subnets for each port and the device. A port can be 192.168.0.1 with the subnet mask of 255.255.255.0 correspondent, and his camera would be 192.168.0.2. The following port would be 192.168.1.1 and so on. You can use the configuration utility IP of Basler to assign these IP addresses for the cameras. However, this becomes a bit a maintenance problem that you have for the right camera the right way-related stays.

  -The last option is to upgrade to Windows Vista or later version, which corrects the network stack such that multiple interfaces can use link-local address perfectly.

  Hope this helps,

  Eric

• How to extend HDMI on Cisco TV presence Codec C60 camera cable

  Hello everyone.

  I need to know how we can extend the camera HDMI cable and the control of camera d-SUB/RJ45 cable up to 50 m.

  We know that HDMI cab be extended to aid commercial Extender HDMI, but we do not know if the C60 uses standard HDMI signal. and what about the control cable. ?

  C60.PNG

  

  You can use any standard HDMI extender to extend HDMI video cable.

  For camera control cable, you can make your own cable from camera to extend existing or just cable one as long as you need. See the camera cable pinout scheme in the PrecisionHDMC camera Guide on pg 17. If the camera cable is more than 5 meters, the unit must be plugged into a power supply for camera (PSU-CAM-V =), as the time is too long for the codec to power the camera.

• Since the installation of the latest IOS i.e. IOS 10.0.1 and 10.0.2, my phone is very slow, especially the contacts do not appear in the search and the camera hangs on startup. the battery is also used faster then the previous version.

  Since the installation of the latest IOS i.e. IOS 10.0.1 and 10.0.2, my phone is very slow, especially the contacts do not appear in the search and the camera hangs on startup. the battery is also faster, then the previous version, use 6s with 64 GB

  Hello naqvi65,

  I see that you have several problems with your iPhone after updating to the latest version of iOS. These issues include problems of performance, inability to find contacts at a Spotlight search, problems with enforcement camera freeze after the launch and the battery discharge more quickly than what you are accustomed. I want to help you find a solution for these questions!

  To answer your questions with performance and your inability to find contacts, we will try to restart your iPhone first to see if the problems persist. Take a look at this resource for more information:

  Restart your iPhone, iPad or iPod touch - Apple Support

  Take a look at this Web site using your photo app troubleshooting:
  Get help with the camera on your iPhone, iPad or iPod touch - Apple Support

  To keep an eye on your battery use, take a look at the information here:
  On the use of the battery on your iPhone, iPad and iPod touch - Apple Support

  To help maximize your battery performance, this site has some good tips for iOS devices:
  Batteries - maximize Performance - Apple

  See you soon!

• Camileo B10, what happens if the USB is connected to the PC and the camera is on shot?

  Manual says that to charge battery camera must be set to off. The question is how the camera behaves if usb is plugged (and power) and the camera is turned on? It works normally, but battery is not looking or camera will take it s usb power and battery power or what? I ask this because I am in need of camera that should save minimum 4 hours without interruptions.

  Hello

  > Manual says that to charge battery camera must be set to off
  > Is that it works normally, but battery is not looking or camera will take it s usb power and battery power or what?

  I think it's just because common USB port provides 500mAh and I don t think it would be enough to charge the battery and to power the display, etc...

  I m no owner of the Camileo b10 but I have a: 30 and if the camera is turned on, the laptop will recognize this as an external storage and cam. But I charge the battery with the external AC adapter.

• buy an iphone 5s by amazon and I came with iCloud blocked an account... {I called the seller and does not that I do that I'm from Venezuela please need your help}

  buy an iphone 5s by amazon and I came with iCloud blocked an account... I called the seller and does not that I do that I'm from Venezuela please need your help

  No one here can help you. The device is locked activation. Since you have made the purchase by Amazon, you can check with them to see if they will stand behind it. No one on the forum, or Apple can help you remove the lock. Only the previous owner can do this. I suggest that you demand a refund, so let's start a claim with Amazon about this dealer.

• Error of flow OR MAX and attribute camera out of reach

  I recently bought a camera Point Grey Grasshopper3, it seems to work fine at point software fly Cap Gris provides, but I get an error NI Max when I try to do a simple puncture (see below). This error appears every time I try to catch a time image the first after the opening OR MAX, even if the flow is set to maximum. Then I change the flow under control of the unit to any integer 125000000 max, and the camera works very well for MAX. It will capture images as much as I need. Then I save the camera output MAX, open MAX once again, it shows my saved settings, I'm going to capture images and I get the error again. If I change the range regardless of the number and it works again in the same session in MAX.

  I had a gray point Zebra2 work very well and he used in my program LabVIEW with IMAQdx to acquire images. When I try to use grasshopper3, LabVIEW returns error attribute camera out of reach of the VI camera configuration. I use to test the camera of the VI is the camera just to open, configure acquisition, start acquiring, get the picture, cancel the acquisition and nearby IMAQdx camera configuration. I did twice open MAX, change the flow, save the camera, close MAX without grasping an image and then was able to acquire images in LabVIEW in the first inning. I would run the VI once again and then it returns the error to attribute camera out of reach. I changed the packet size, resolution and the frame rate of the camera with a difference in errors.

  Since I am able to images of the stream from the camera to the gray point fly capture and Max after activating/deactivating the flow layout, it leads me to believe there is some sort of error MAX/LabVIEW that prevent me to capture the images.

  Any ideas? Has anyone else had this problem with MAX and LV?

  Looks like the point Grey cameras showed this error before the firmware on the basis. See this linkfor such a forum. I would monitor the camera (*.icd) file located in the data folder IMAQdx in public Documents to see if the actual value is be replaced after the configuration of the camera has been saved in MAX. There is a chance that the GigE. XML file which is transferred from the camera is overwrite these values in the unacceptable value. See this linkfor a KB about this error, which leads me to believe that this may be the problem.

• HP and Sony camera

  I have a Sony DSC T10 and a HP Envy I7 TS with Windows 8.1 and the camera is not recognized when plugged into a USB port.  Device Manager does not recognize the device.  Installing the updated Sony software and it does not find the device.  Any ideas, please.

  Hi clb7122,

  When a device is not recognized by the computer, it can be for several reasons. I've included the document "troubleshooting USB (Windows 8) connections." Please select the option for USB device not detected by Windows (no name of device in the Device Manager)and follow the General troubleshooting steps.

  Please let me know the result of the resolution of problems and if you are able to correctly, connect your camera after troubleshooting.

  Thank you.

• After 10 Windows Installer on Audio SW5-11-18R3 and the camera will not work. How can I fix?

  Tried the upgrade of Windows 10 initially, but it failed with "lack of disk space", then installed full media and all but the Audio and the camera does not work.

  Hi all

  I would just like to make the point that there is a fix that has been made available and applications for a Windows Update is also underway. I'll link directly to the file located on our page drivers and downloads.

  
  
  
  
  
  
  
  
  
  
  
  
  

  Patch

  Acer

  1. fix camera function fail after upgrade to Win10 TH2.

  20160506

  91.7 MB

  30/05/2016

  Download

  Thank you
  Cory

• My system tells me that my network connection is damaged. I ran malwarebytes & it came back negative. I went to shoot to the top of my network connections in Control Panel, and it came in white.

  NETWORK CONNECTIONS

  Can anyone help? My system tells me that my network connection is damaged. I ran malwarebytes & it came back negative. I went to shoot to the top of my network connections in Control Panel, and it came in white, nothing at all, no icons, nothing.        Sincerely, Merlin

  Can you do a system restore at the time where it did not work properly? http://www.officeforlawyers.com/tips/sysrestore.html

  -B-
  http://www.officeforlawyers.com | http://www.OneNote-tips.com
  Author: Guide to counsel for Microsoft Outlook

• Cannot establish network connection. Messages on the icon alternate between "Acquiring network address" and "unplugged network cable.

  Original title: cannot establish a network connection

  Very well, a computer can connect to the internet. Another computer using the same modem cable and fixed connection of the router (for example using the port adapter, not wireless) Wireless does not connect. I suspect that there are has some settings somewhere that are not correct. Can you tell me how to understand where is the problem?

  Messages on the icon alternate between "Acquiring network address" and "unplugged network cable. When I run troubleshooting this is what I get:

  Diagnosis of IP Configuration
  Invalid IP address
  Info	Zero (0.0.0.0) detected IP address
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: reset the network connection
  action	Disabling the network card
  action	Activation of the card network
  Info	Successfully activated network adapter
  Info	Zero (0.0.0.0) detected IP address
  action	Repair Manual: Reboot modem
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  Info	Redirect the user to support call

  WinSock status
  Info	All base service provider entries are present in the Winsock Catalog.
  Info	Winsock Service providers strings are valid.
  Info	Entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.
  Info	Entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.
  Info	Entry provider RSVP UDP Service Provider managed the loopback communication test.
  Info	Entry provider RSVP TCP Service Provider passed the loopback communication test.
  Info	Connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter
  Network location detection
  Info		Using the Internet connection at home
  Identification of network adapter
  Info	Network connection: name = Local 2, Device network connection = Intel(r) 82562V-2 10/100 Network Connection, MediaType = LAN, type = LAN
  Info

  Ethernet connection selected

  State of the network adapter

  Info

  The network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn

  FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  warn

  FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  error

  Could not make an HTTP connection.

  error

  Could not make an HTTPS connection.

  error

  Could not make an FTP connection.

  I found the problem (s), even if I am always left with a few questions.

  During this process, I have disabled the firewall, but that did not help. However, I noticed 'tweaks' accessed via the tab 'Advanced' in 'Microsoft Firewall' which looked like, they must be checked in order to access the internet. I checked these and reintroduced the firewall. After I got things working, I unchecked them and things still worked so I obviously don't understand what these parameters.

  The solution:

  (1) I have to go straight from the modem cable to the computer. I can't have a cable modem, router wireless, computer, even if using hard wire, and even if this same configuration works with another computer. Also, I can't use a cable length to go from modem to the computer. So, it seems to have had a problem of cable length. Power problem? Only connected to this computer devices are the mouse, the keyboard and the Ethernet. Would not this be fixed with an upgrade of the power supply? Or is it due to the quality of the Ethernet hardware on the motherboard? It's a Dell Vostro 200.

  (2) in back and forth between configurations while following the problem, you must think to unplug the modem to reset between each configuration. You may have stumbled upon the solution, otherwise he's not shot. Also, I unplugged the cable from the modem when you reset data cable - do not know if it was necessary. I wanted to limit the degrees of freedom that I had a lot, as it was.

• I bought a computer from a business and it came not with all drives.

  Original title: I bought a computer and it came not with all drives.

  I bought a computer from a business, and it was a computer on the network. It came not with all drives. Is it possible to reformat the system with out having to re - buy windows xp or office? Can I get copies of XP and Office? I still have the XP sticker with the computer.

  If they don't give you the disks, all you need is a boat anchor. Ask them to give you the disks and product keys. Otherwise, you will need to buy.

• my computer is very slow and the sound is crackling and move icons on their own i have norton security and scanned and it came with a few flaws, but has not yet sorted

  my computer is very slow especially on the startup sound is crackliing and when you watch videos it jumps a little icons often have moved when I start I have norton security and it did an analysis complete and it came with a few things but has not yet sorted

  Hello

  Try to update norton antivirus defination files and run a full system scan in SafeMode (http://support.microsoft.com/kb/315222).

  I hope this helps.

• How to get the angles of view (horizontal and vertical) camera?

  How to get the angles of view (horizontal and vertical) camera?

  The horizontal and vertical field of VIEW properties are available with the camera_get_physical_property() function.

  Who is using the C API of the photo. I don't think that you can access by using the control of the camera of Cascades.

• BlackBerry Smartphones after upgrade to v4.5.0.138 - Can t Sych elements between mailboxes and my camera deleted

  Yesterday I was prompted to upgrade my BBerry (Curve 8330) software and I did. Now, I run v4.5.0.138.

  I have four parameters separated on my BBerry, Hotmail 2 and 2 Gmail accounts email accounts.

  Before the upgrade, I could "synchronize items in the mailbox of [these] [are] and my camera deleted"-I had this option to 'Yes' for each of my mailboxes in the General settings for each. Whenever I chose to delete an e-mail message from my BBerry, I was invited to remove the only device or remove it from the device and the server. It was great! Often, I want to delete my BBerry and the server. It really helped me keep my Inbox clean e-mail.

  After the upgrade, I don't have this feature. Hotmail accounts have even this option available in the General settings. Gmail accounts have this setting, I put 'Yes', but I'm not invited when I delete the messages, and the messages will not be deleted on the server.

  Anyone has any ideas on this subject?

  Welcome to the DiskEyes forums

  The settings you are looking for are in the Mail folder. Press the menu/blackberry button > Options. In the Options go to the reconciliation of the enamel. You must configure each email from there. Change "Message Services" to the email that you want to configure, and then under it, change the "remove the ' to 'ask '. Press ESC and save.

  After the back if you have problems doing that.

  See you soon,.