Can I programmatically change the default property to create for all elements of the front panel?

Similar Questions

• How can I programmatically change the parameters of voltage range in a DAQ Assistant

  Hello

  First post here.

  I need to be able to change the properties of voltage range of a daqmx assistant DAQ based on user input.  My material, an SCXI module - 1102C does not change this property on a running task, so I would together the range of input voltage analog before activating the DAQ Assistant, or break the DAQ Assistant immediately after it starts, set the values, and then resume.

  I don't know how to change the task ahead because the DAQ assistant creates the task when it is running, and there is no job before that.

  In the attached photo, I have a conditional section, configured to run only if the loop iteration is 0.  I take the task of the Daq assistant, sending him stop vi of task, set the property and then send the task with the snap the vi task. I can watch him run with lightweight debugging on, and everything seems to work properly, but on the second (and all others) iteration of the loop, I read I. Max and it seems that a re DAQ Assistant set it to the 5V.  You can see what's going wrong here?

  BTW, there is a continuous acquisition and the code doesn't produce error messages when executing.

  I've encountered a similar question someone posted here in 2006, but his question was specifically a Labview API (VB, I think) and not a real solution of G.

  Attached are the real vi in question and a PNG of the block diagram.

  Thank you!

  Ruby K

  First of all, if you want to start getting beyond the basics with the DAQ hardware, you have to stop using the DAQ assistant and do it with lower level VI DAQmx.  There are hundreds of examples in the finder of the example.  You can even make a right-click on the DAQ assistant and select open front panel.  This will create a Subvi, you can open and see what is happening behind the scenes.  Do it.  I think you will find that the task DAQ is recreated on each (although I'm not 100 percent the way parameters are established or maintained in each section of this sub - VI).

  The second problem is that you have a bit of a race on iteration 0 condition.  These two property DAQ nodes are running at the same time.  Thus, when you read the AI. Max, this can happen before or after the AI. Max is located in the structure of your business.

  Thirdly, make sure that involve you your son of the error.

• Can I programmatically change the active group on a Hypertrend in DSC?

  I would like to know how to change the active group of a hypertrend program in Labview DSC.  I saw a link that says it can be done at Lookout.  But in the module DSC, the active group is read-only.

  I know a hard way to do it.  I could save the settings of hypertrend as xmlSettings in a temporary file.  The active group is one of the parameters.  I could then change the group active in this file text to point to the new group, and then reload the settings.  But this isn't a clean way of dong it.

  Anyone know if there is an easy way?

  I found a way to do it but not very clean.  I don't know why there is no function to change the current group.

  Here's how I did it.

  

• change the front panel

  How can we change to frontpanel in labview?

  I wrote a program where the appearance of the façade must be different.

  How do you make different frontpanels in the face?

  What about Michael

  I still don't get that you have to go with two screws separated, or you could make your project with a single main VI. If so, here is a small example with TAB controls:

• How to programmatically change the width of a graph?

  How can I programmatically change the width of a form of wave or waveform graph? When I create an implicit property of a chart or a graph node, it is read-only. Change the boundaries of the parcel has worked in earlier versions of LabVIEW, but not anymore.

  It works for me in LV2013 but I use the plot area: Dimensions: width property.

• How can I programically change the background color of a VI using another VI?

  Is it possible to change the background color of text of an indicator on the front of an a different VI VI?

  Hello

  You can programmatically change the front like that, code

  Can I programmatically change the colour of the façade?

  http://digital.NI.com/public.nsf/allkb/0DDBDB2FE2F54A5286256918006D7BB9?OpenDocument

  Then using VI Server, you can get a reference to VI on another computer to change it (or on the same machine)

  Hope this helps,

• Error when changing the language of the front panel in Japanese

  Hello world...

  I'm changing the front panel of the English language to Japanese. To do this, first I exported the strings through the Tools->Advanced-> export channels.  After that I changed one of the label in Japanese and saved with Unicode encoding (as with normal ASCII coding Japanese texts will not be read). I imported the same file I recorded in a Unicode encoding format. But it shows that the error given below

  "Error analysis during the import of channels
  to test Main.vi
  of D:\Riyas\Work\X 520\28-11-15\X520 RT-Host 20151127\Strings\Test Main_Import 1. txt
  "Saturday, November 28, 2015 11:09:14.

  (See the attached screenshot of error)

  So I tried to import the same file ASCII coding mmee, then it is successful. But the problem is that the modified label is not in Japanese that it shows a few points mark. I'm able to import the channel file saved in ASCII format code but the channel with coding ASCII file will not read Japanese texts. So please help me to solve this problem.

  I need to import a channel file saved with a Unicode encoding or in any case format to enable Japanese texts as ASCII coded format.

  I modified the configuration settings to activate the Unicode format as follows "UseUnicode = TRUE'." I'm using Labview 2014.

  Thank you...

  racahmd wrote:

  My requirement is to change the language of the labels on the front. Is it possible to export the settings of the legend and label parameters separately? Currently, I am only able to export the two together. Also when I import the unicode file that does not contain unicode characters, it shows the same error.

  Perhaps the requirement is statesd as such because the people who wrote the requirement had no idea, you can keep the labels even but change the subtitles only.  Changing labels is a massive effort that could have profound ramifications to the code itself.  Not the same with a legend.

• programmatically change the def type

  I inherited program that I'm editing with the least amount of change.  One of the controls is used in all of the auxiliary of the screw, and it's a def type.  It's a cluster containing three groups.  I want to programmatically change the limits of data entry on one of the digital controls in one of the clusters of void.  I can't get to the point where I can create a node property to do this.

  The type of data you get from the [] Controls property is a generic control. You must cast to a cluster.

• programmatically change the tab in TabbedMobileApplication?

  I have a TabbedMobileApplication that has X number of tabs. In a view to 1 of the tabs, I want to programmatically change the tab selected to another tab, as if the user clicked the button on the tab at the top of the screen. Is this possible? I searched through the TabbedMobileApplication API and can't seem to find anything.

  Much appreciated!

  Hey,.

  Currently, the best way to change the tab selected by program would be to set the selectedIndex on browser of the application property.  You would do so this type:

  FlexGlobals.topLevelApplication.navigator.selectedIndex = x;

  Note that the navigator in the TabbedMobileApplication class property is not the same browser referenced in a view.  Doing so navigator.selectedIndex an inside view would not work.  I hope that makes sense.

  Let me know if you have any other questions.

  Chiedo

• Programmatically change the selected cell/line of control multi-column listbox

  I want to programmatically change the selected cell of a multicolumn list box whose selection Mode is set to highlight the whole line.  I would use this to highlight the line whatever the list box, I chose to.  It would work the same way if the user has clicked on a line to select and highlight that particular line.  Set Active cell does not fulfill this.

  Steve

  Try to use the property value; p

• Lightning: How can I permanently change the event organizer email address when he invited?

  I have two email accounts with Thunderbird; one is the default account from which my emails are sent. However, when you attempt to send an invitation to the event through lightning, my secondary email is displayed in the field of the organizer and it cannot be changed.
  Thank you, in advance, for all the answers.

  Right click on the calendar in the left pane - properties
  Change the e-mail address you like.

• programmatically change the date of modification to a folder

  Is it possible to programmatically change the date of last modification of a file?  The OpenG info VI file doesn't seem to work for a folder.

  I think you should be able to use .NET, as shown in the attached VI (although in my case, each file fails this and says that the file is being used by another process. If the same thing happens to you I suggest looking more far away).

• How can I permanently change the NVIDIA geforce of Intel(r) hd graphics?

  I would like to know how can I permanently change the type of adapter display card Intel (R) NVIDIA geforce hd? Previously, when I bought my computer, it is equipped with one chart type-NVIDIA geforce and everything goes fine until I installed Intel(r) hd as you are prompted by windows update. Since then, my computer have encountered many problems, especially when you play high graphics... I tried to move from the graphics card Intel (R) NVIDIA geforce hd when playing games... and yet, the performance is not as good as the last time where I did have only one chart. Because of this, I would like to change or define main graphic geforce NVIDIA and Intel (R) hd as secondary, or if possible, permanently remove the hd Intel (R).

  Hello

  What is the make and model of computer?

  What is the Windows operating system?

  Follow these steps to disable Intel

  http://www.WikiHow.com/disable-the-onboard-graphics-and-install-a-new-graphics-card-in-your-HP-Pavilion-6630

  HP Support Doc

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c01684404&tmp_task=useCategory&LC=en&DLC=en&cc=us&product=4215700&lang=en

• How can I change the visibility of the images pasted on the front panel?

  Hello

  I'm using LabView 8.5 and I pasted pictures on my front.

  Is it possible to programmatically change the visibility of these images (i.e. make them poster sometimes and not at other times)?

  It doesn't seem to be an option to get a node visibility (or anything else stripped) when I have secondary click on images.

  Furthermore, if there is some sort of control to the 8.5 I could load and display images in order to get this feature visible visible/no, which would also be useful.

  Thanks in advance

  Frenk

  Yes, you use the Brush tool even that you use to change the color. One of the color options is a white search box with a "T" in it.

• programmatically change the range structure case

  I think I already know the answer to that, but I'll ask anyway. In the attached picture, is it possible to programmatically change the range of numbers used by the case?

  Tay

  I probably would solve the problem by program, for example as follows.

  Start by Ravens idea above and use a picture of the limits of the range, for example as described here.