Cannot access the local admin page after first start
Hello
I am not able to access my newly purchased RN202, SN 45Y2535W003FC. I just plugged the power cable and turned on, but the power light keeps blinking even after hours. The NAS will connect to my local network with the ip 192.168.178.32 and ends by RAIDar under this address. However, the local admin under https://192.168.178.32/admin and https://192.168.178.32 page (even with http://) is not accessible. The connection is not accepted (cannot be connect-page in the browser). Also access more ReadyCLOUD is not possible, because the NAS cannot be discovered. Currently, there are no hard drives in the NAS. I also tried to insert a HARD disk already formatted in combination with a factory reset, but it does not work with the same result. It's already a replacement unit by my retailer the first device showing the same behavior, so I excluded a technical defect. What I am doing wrong? Any help would be greatly appreciated.
Best regards
Patrick Schmidt
OK I found the solution by myself. Without a HARD disc inserted the NAS will not start correctly. As mentioned, I already tried to insert a HARD drive and then do a factory reset. Now, I saw that I have is to not properly place the HARD disk. If you open the lock on the grid (the thing in which you put the HARD drive), then you can not insert in the case completely and do not connect the connector of power und data. Maybe a little more detailed manual on it (for Dummies like me) would be useful. Argh...
Tags: Netgear
Similar Questions
-
ASA 5505 IPSEC VPN connected but cannot access the local network
ASA: 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
Pool VPN: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.
I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.
Here is my setup, wrong set up anything?
ASA Version 8.2 (5)
!
hostname asatest
domain XXX.com
activate 8Fw1QFqthX2n4uD3 encrypted password
g9NiG6oUPjkYrHNt encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.1.253 255.255.252.0
!
interface Vlan2
nameif outside
security-level 0
address IP XXX.XXX.XXX.XXX 255.255.255.240
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain vff.com
vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0
access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging trap warnings
asdm of logging of information
logging - the id of the device hostname
host of logging inside the 10.1.1.230
Within 1500 MTU
Outside 1500 MTU
IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt AD
AAA-server host 10.1.1.108 AD (inside)
NT-auth-domain controller 10.1.1.108
Enable http server
http 10.1.0.0 255.255.252.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 10.1.0.0 255.255.252.0 inside
SSH timeout 20
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntest strategy
Group vpntest policy attributes
value of 10.1.1.108 WINS server
Server DNS 10.1.1.108 value
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the password-storage
disable the IP-comp
Re-xauth disable
disable the PFS
IPSec-udp disable
IPSec-udp-port 10000
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntest_splitTunnelAcl
value by default-domain XXX.com
disable the split-tunnel-all dns
Dungeon-client-config backup servers
the address value vpnpool pools
admin WeiepwREwT66BhE9 encrypted privilege 15 password username
username user5 encrypted password privilege 5 yIWniWfceAUz1sUb
the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username
tunnel-group vpntest type remote access
tunnel-group vpntest General attributes
address vpnpool pool
authentication-server-group AD
authentication-server-group (inside) AD
Group Policy - by default-vpntest
band-Kingdom
vpntest group tunnel ipsec-attributes
pre-shared-key BEKey123456
NOCHECK Peer-id-validate
!
!
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end
Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.
The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.
On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.
-
Cannot access the local users and groups
Hello everyone, I got this error since April 2010:
Cannot access the computer ComputerName. The error was: invalid syntax.It is not really bad for me, because I used to use the cmd console.
I followed several recommendation to solve this error, but without success. Many colleagues have the same error. About 100 of the 500 have this problem.
Don't tell me to reinstall the PC because it is not possible. I have no spare time to set my PC again and install all required software. And to reinstall the PC isn't sollution.Re-register the dll or other files not work. Not work replace the msc or cpl files. Installation of the admin packs, technical resource kits or installer also not work.
No errors in the application logs, no errors in the system log, no errors in the security logs. GPO is clear. The same mistake in compmgmt.msc, lusrmgr.msc, or when I add the MMC snap-in. So I guess that the error in the XML (MS XML) parser tool or in the msc file.
Do someone have the solution for this?
Yet once the relocation no solution!
Hi Peter,.
In this case, I would say that you post your question in the Microsoft TechNet forums such that there is a problem with more than 100 computers.
-
custom palette with tabs to swf Flex cannot access the local file system
OK, with Flash Player 10, we can load and save local files from a flex web application, then why can't I in the bridge, when I load the SWF in a palette with bridge tabs, load and save functions no longer work.
Is it because I'm loading as a ScriptUI called range of flash, instead of a palette of HTML?
I tried the overall Flash Player security in order to allow the authorization of my swf and created a .cfg, but nothing seems to work.
Help, please.
Thank you, Todd
I don't know exactly how your Panel is a failure. I have attached three examples of Flex projects that include the JavaScripts and Flash panels for bridge. These all worked for me in Bridge CS4.
To access the local, I used FileRefrence.save () for these tests - note that this method is file system was added in Flash Player 10, and so this will not work in Bridge CS3, which uses the Flash Player 9 when you use a widget Flash Player in ScriptUI. In addition, to compile the example I had to modify the Flex builder projects require Flash Player 10 by changing the settings on the page 'Flex compiler' project in Flex Builder settings.
If you use another method to access the system files that works with Flash Player 9, please let me know what it is and I can test it.
Among sovereign wealth funds also gain access to the network. To activate SWF access to the network, I had to add a file of global security settings. Information on creating these files are available here:
http://www.Adobe.com/devnet/flashplayer/articles/flash_player_10_security.PDF
But, for example, on my mac, I put all these projects in a "BridgeFlashPanels" folder on my desktop. Next, I created the BridgeFlashPanels.cfg file in/Library/Application Support / Macromedia / FlashPlayerTrust. The .cfg file had a line: the path to the folder on my desktop.
A description of the panels:
PanelWithNetworkAccess - this Panel has a 'Test' button, when clicked, loads http://www.adobe.com and place it in the text box (note, it will be just the raw HTML, does not make the page).
PanelWithFileSystemAccess - for Flash Player 10 only, this Panel has a Test button and a text field. When you click the Test button, it writes the contents of the text box in the BridgeTest.txt file, unless you choose another file.
PanelWithNetworkAndFileSystemAccess - for Flash Player 10 only, this Panel has a text field and two buttons: "Load Test" and "Test to save." The load test loads http://www.adobe.com in the text field and save him testing saves the content of the text field to BridgeTest.txt.
To try signs, navigate the bin-debug for each project files with Bridge, the .swfs and .jsx files are there. Double-click the thumbnail for the .jsx and bridge must run the script and add the sign indicating the SWF file.
-David
-
Cannot access the EBS login page
Hello
I have already installed EBS VISION demo and all the services it and race, but I can't access the login page.
http://ebs122.ebsdomain:8000/OA_HTML/AppsLogin
output de./adstral.sh:
********************************
All services enabled for this node are started.
adstrtal.sh: exit with status 0
adstrtal.sh: check the logfile /d01/oracle/app/VIS/fs1/inst/apps/VIS_ebs122/logs/appl/admin/log/adstrtal.log for more information...
adstrtal.log:
[Service Control implementation report]
The format of the report is:
< group Service > < Service > < Script > < status >
Root Service Enabled
Adnodemgrctl.sh root Service NodeManager Started
Web administration enabled
Web Administration AdminServer adadminsrvctl.sh Started
Web Administration OracleTNSListenerAPPS_VIS_ebs122 adalnctl.sh Started
Entry Point active Web services
Entry point Web Services Oracle HTTP Server VIS_ebs122 adapcctl.sh Started
Web Entry Point Services Oracle Process Manager for VIS_ebs122 adopmnctl.sh Started
Application Web enabled services
Web Services application oacore_server1 admanagedsrvctl.sh Started
Web Services application forms_server1 admanagedsrvctl.sh Started
Web Services application oafm_server1 admanagedsrvctl.sh Started
Web Services Application forms-c4ws_server1 admanagedsrvctl.sh Started
Services enabled processing batch
Batch Processing Services OracleConcMgrVIS_ebs122 adcmctl.sh Started
Batch Processing Oracle ICSM VIS_ebs122 ieoicsm.sh people with disabilities Services
Batch Processing Services Oracle Fulfillment Server VIS_ebs122 jtffmctl.sh Started
Other disabled Services
Other Services OracleFormsServer - forms VIS_ebs122 adformsrvctl.sh disabled
Other Oracle MWA Service VIS_ebs122 mwactlwrpr.sh people with disabilities Services
Any help?
Thank you
Luis
Hello. I already fix the problem. I did:
iptables-f
Concerning
-
HP ENVY 15-j181na N: TouchSmart cannot access the driver download page!
Hello, since yesterday I am trying to download hp envy Touch smart 15-j181na notebook drivers, but it gets stuck to the loading screen: "HP is compile your results." It could take up to 3 minutes, depending on the speed of your computer and connection. Thank you for your patience. "and nothing ever happends, pls help me because I did a fresh install of Windows 7 64 BIT and I need the drivers, thanks in advance.
Hello:
The HP support pages did not work for several days.
HP is aware of the issue and working to resolve it.
For now, try the W7 x 64 drivers and software from the HP 450 G2 on your model except the graphics, the BIOS and firmware files.
http://h20566.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=6943827&swLangOid=8&swEnvOid=4058
The graphics... try this...
1. install the driver Intel chipset installation utility of the model above and restart.
2. install the Intel graphics driver and restart. The second listed driver is the automatic installation file.
3. install nVidia HD graphic driver and restart.
http://www.nvidia.com/download/driverResults.aspx/86506/en-us
-
cannot access the drive of bitlocked after reinstalling windows
Hey guys!
I had locked a drive using bitlocker. I reinstalled my windows! now, I can't access the drive (I didn't turn off bitlocker or suspended.)
When I click on the drive it says you have to format it! and when I click on format it says is impossible to format!
I have 40 GB of data that I can't lose!
pliz help me!
You need a certificate to access a bitlocked drive.
BitLocker Repair tool to recover a diskhttp://TechNet.Microsoft.com/en-us/library/ee523219 (WS.10) .aspxhttp://social.answers.Microsoft.com/forums/en-us/w7security/thread/19f28028-EACE-4878-b5e5-8cd78c19f6f3If that fails, then you have to recover your files from your external backup media. -
Hello
I have 3 pages, that's all first my login page if the user is valid, then go to the second page, on the second page, I enter the data for the user and after you enter the data, I'm going to the next page but for this 3rd page I get network error (Try Again), but this code works fine on google chrome browser my machine.
What is the problem here?
After the installation of new WebWorksSDk, my problem is resolved automatically...
-
cannot access the internet after upgrading to firefox 30.0 on windows 7
After the upgrade to firefox 30.0 on windows 7, cannot access the internet. FF 30.0 works OK under Vista
Sometimes it's because of your security software thinking that the upgrade may not be legitimate. You can consult this article: problems connecting to websites after Firefox update.
-
Hello!
So I'm at the end of my rope with this one... it lasts for months, and I keep revisitng every two weeks to try and fix that and every time to be completely frustrated. I found this forum tonight, so here goes...We downloaded a few games on the HP Games Web site. We download them and everything works fine. Then, we will open the games and this pop up error message:
"Windows cannot access the specified device, path or file. You can not have the appropriate permissions to access the item.These games used to run fine, and I have no idea why they now have problems. We have a Vista operating system, 1 account who is the administrator, the Parental control is disabled (or if we believe).
If anyone can please help it would be much appreciated! We have a monthly membership to this site of game and continue to accumulate credits, but may not use it. It makes us crazy!
Thank you in advance!
Hello Heathie,
Thank you for posting. It seems that the program is no longer on your computer. This can happen if the game files are deleted, but the game itself has not been uninstalled correctly. I recommend you to download the game again to a location on your computer where you can easily find and install it. This should fix the problem.
Please let me know if this helps you.
Zack
Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think. -
Cannot access the WAP54G after firmware upgrade
I have updated the firmware of my WAP54G v.2; We just started to use the AP again and when I checked, I thought I would update. I was going to 1.2 or 1.4 to the latest firmware using this link http://homesupport.cisco.com/en-us/wireless/lbc/WAP54G, version 2. I could see the AP before starting my Dlink router. I downloaded the firmware and the upgrade of the access point. She completed successfully, but when I tried it I could reach him is no longer. I checked the router and it shows is no longer there and I can't access it via the installer.
How you try to access the router configuration page? If the access point is connected to your d-link router, make sure that your router's default ip address and AP are in the same range. The IP default WAP54G is 192.168.1.245.
If the router's default IP address is different, so you will need the AP wired to your computer and assign a static ip address to your computer ie: 192.168.1.10 and then connect to the access point configuration page and settings wireless entry and change the default IP of AP, which is of the order of your d-link router.
-
Cannot access the BEFSX41 router Config page Win 7
Hi, I have a BEFSX41and am not able to access my router from any browser config page I have on my system. I use IE and FireFox and when I punch in the IP address for the router there is just there and about 30 seconds later, says that there is a mistake and that the connection has been reset. It is a 64-bit installation and I also have another computer that goes through the same router, is 32-bit and doesn't have this problem.
I added a NEW driver for my Realtek NIC and it still happens. Another machine that I have on my network ALSO has a Realtek NIC but can still access the router config page.
Someone at - it else here has the same problem?
OK, problem solved. I used a different IP and the problem disappeared, thanks for the help.
-
Hi I encounter an error message "Windows cannot access the specified device, path or file. You don't have appropriate permissions to access. »
The error message every time I click on administrative tools of the window (including the Control Panel, windows update, the Windows Explorer, etc.) but without impact on other programs I have.
I rebooted in safe mode and discover that everything works fine (no error message will appear when you click on window management tools).
I proceed to do a clean boot-> first disable all services of third parties (message yet to come), and then clear the components of the service windows (message yet to come)
I tried to type "explorer.exe" in the start menu-> search field then click right highlight to run with administrative rights, then received another message of error "Server execution failed".
I am the administrator account on this PC - and have full access.
The error seems to have appeared on 11 August after Windows Update the following:
Update of security for Microsoft Windows (KB2536276, 2556532 2559049, 2560656, 2563894, 2567680), and
Update for Microsoft Windows KB2563227
A security update for the Microsoft.net framework 4 client profile (verson 1)
There is no installation of any software or updates outside the windows update.
I also tried to restore the windows before August 10, 2011, but that did nothing.
As the error prevents me to access any object Admin window - I'm unable to retrieve the product ID and write to Microsoft Tech and ask for help.
I hope some of you can offer the suggestion of possible solutions (I really want to re - install window 7 and other software, I'm sure).
Thank you.
My solution works in about 2 minutes, it's a very weird error and only happened to 3 jobs in the last 3 years, this solution does not need to create another account if local administrator is active and allows access to the corrupt user documents ect.
Log in as the local administrator or a domain administrator
If the local administrator is not activated refer to http://support.microsoft.com/kb/555910 and after completing these newspapers of steps on the local administrator account.
Locate the user for example files. C:\Users\[username]\
If you see no AppData press Alt to see the toolbar at the top of the window, select Tools > folder options, go to the view tab and select "Show hidden files, folders and drives" click OK.
Go to AppData\Local
Select all (Ctrl + a).
Delete
* Do not delete credentials (as it will remove their wallpaper) *.
This allows to release the error.
-
Jpg file printing - windows cannot access the specified device, path, file
Original title: I have a similar problem, I can open the jpg fine, I can't print it
I have a similar problem, I open the jpg fine, I can't print it, permissions are fine. I get the same erorr-windows cannot access the specified device, path, file...
Hi Janine.
1. are you able to print documents?
2. the problem occurs only with a particular image file?
3. how the printer is connected to the computer?
4. What is the brand and model of the computer and the printer?
5. have you logged as administrator?
Method 1:
First of all, try to print a test page and check if it works:
To print a test page
Method 2:
I suggest you check out the link to use the System File Checker tool (SFC) to troubleshoot missing or corrupted system files in Windows:
Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)
Note: you must have the Windows XP disc to make the SFC scan.
Method 3:
I suggest you to turn off all third-party security software and the Windows Firewall and then try to print the file:
How to change or remove a program in Windows XP
http://support.Microsoft.com/kb/307895
How can I turn on or turn off the firewall in Windows XP Service Pack 2 or later versions?
http://support.Microsoft.com/kb/283673
Note: run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.
Let us know the results.
-
Hello
I recently changed to use AVG free Antivirus Vista 2010 edition and since then (next day) seems to be locked out almost everything on the computer other then IE. Open any kind of .exe translates into "Windows cannot access the specified device, path or file. You don't have the appropriate permissions to access the item. "I can access the Control Panel, but when I try to run something (a user restore Sys account) nothing happens or I get the same error. I can not even access/cmd?
Operating system is vista 64 bit home premium
Computer has 1 which is defined as administrator SP1
Tried to do a restore of the system in normal mode and safe, the two will not start.I have a feeling I know what the problem is, that when you look at the properties > Security "Progam files" in the 5 groupnames user administrator has not enabled in the lower area of permissions? Guess a virus has locked all accounts to use the machine key files? (When editing and allowing the admin to have full control etc. in written authorization, I get an "access denied" Message.) Be honest this really problems out of my PC knowledge, I would usually just reformat if I hit I can't solve a problem, but this time reformating is not the best option.
Thanks in advance for any help, I would really appreciate it, it left me speechless!
PS. read through the similar questions and have used the "fix windows' programs, with nothing working or me being not able to access something used.
Hi Dany88,
First of all, I would say that you uninstall security antivirus vista 2010 of computer software, since there are several questions on the computer after installing. This software may have created conflicts between other programs on the computer.
As you face problems to access items from 'Control panel', I would say you visit the security software vendor's Web site and search a tool of suppression using which you can uninstall the software.
Important: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.
If questions are set after uninstalling security software, I suggest that you change the security antivirus vista to some else software or contact the vendor of the software for more information.
I would also say that you are investigating the computer by using the methods mentioned in the link below.
How to get rid of malware or viruses
http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/ba80504b-61f1-4D71-960f-b561798b7b42See the link below to find out how to start in safe mode.
Start your computer in safe mode
http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-modeI hope this helps!
Halima S - Microsoft technical support.
Visit our Microsoft answers feedback Forum and let us know what you think.
Maybe you are looking for
-
MAC G4 - starting from different OS
Hi I need help. I'm completely new to Mac. I have two Power MAC G4, an assembled in Ireland = Y and the other Singapore = Z, but inside, the components are different. I have two HDD, drive HARD-A = OS X 10.3.1 (7 C 107) and the other a HDD - B = BON
-
W1907 monitor: windows 10 for w1907 driver
I have upgraded to Windows 10. My w1907 monitor requires the driver support resolution 1440 x 900. Windows 10 uses the generic display for my monitor driver and it does not support 1440 x 900. Where can I find a Windows 10 driver which supports 14
-
Passport Passport blackberry blackBerry battery
Hey I just got my passport I must charge for 12-24 hours for the first time?Or use it until the end of the battery and then load it?Thank you
-
Disabled accounts of internal users of ISE
Hello I noticed this morning that, rather than the regular minimum number of users during the night on our wireless network from about 200 we had 68. Missing customers were some infusion pumps Hospira that have been set up with accounts of local user
-
Please help me understand the submenu
HelloHow to make the submenu and more, how I see what I've done in the browser?I have tried, but somehow, it does not work.Please help me, I'm lost!See attachment.Thank you.