Cannot access the VPN server located behind the corporate firewall.
The VPN server was created by myself, in my Department. I can access the server from anywhere when I am in my business network. When I'm at home, I can't even ping the VPN server WAN interface. When I try to connect via the cisco VPN client, I get the message ' reason 412: peer remote not responding. "
The main my company firewall blocks external traffic?
Should I change anything in the VPN server?
I heard about port forwarding, but have no knowledge about this. Port forwarding is done on the VPN server or the main firewall?
Also should I go and ask the company system administrator to enable certain ports for the public IP address that I use for my server?
I hope you can help
Concerning
Yes, quite correct. Please open ESP protocol UDP/500 and UDP/4500 for IPSec VPN.
Tags: Cisco Security
Similar Questions
-
Cannot access the Windows Firewall
The thing is I did an ad hoc network with my dads laptop computer and it seems that I have to use Windows Firewall to enable ICS but every time I click on "change firewall settings a dialog box saying: Windows Firewall settings cannot be displayed because the associated service is not running." You want to start Windows Firewall/Internet Connection Sharing (ICS)?
Yes/NoAfter I clicked on yes I get another dialog box saying: due to a problem not identified, Windows cannot display Windows Firewall settings.
OkI have no idea on what to do. Can anyone help?
Hi Mawuko wassel,
· Do you have any other firewall software or security running on the computer?
· Did you do changes on the computer before the show?
You can reset the firewall and then search for the question.
a. click Start, click run, type cmdand then click OK.
b. at the command prompt, type the following command and press ENTER:
Rundll32 setupapi, InstallHinfSection Ndi-Steelhead 132 %windir%\inf\netrass.inf
c. restart Windows,
d. click Start, click run, type cmdand then click OK.
e. at the command prompt, type the following command and press ENTER:
Netsh firewall reset
f. click Start, click run, type firewall.cpland then press ENTER. In the Windows Firewall dialog box, click on (recommended), and then click OK.
You can also view the article in the knowledge base Microsoft for more information:
Could not start the Windows Firewall service in Windows XP SP2:
http://support.Microsoft.com/kb/920074
Hope this information helps.
-
VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK
I tried to set up a simple customer vpn using this document
VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK BEHIND "RA"...
6.3 (5) PIX version
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the encrypted password of VmHKIhnF4Gs5AWk3
VmHKIhnF4Gs5AWk3 encrypted passwd
hostname VOIPLABPIX
domain voicelab.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list 101 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 101 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 102 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 102 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside 208.x.x.11 255.255.255.0
IP address inside 172.10.2.2 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool voicelabpool 172.10.3.100 - 172.10.3.254
history of PDM activate
ARP timeout 14400
NAT (inside) - 0 102 access list
Route outside 0.0.0.0 0.0.0.0 208.x.x.11 1
Route inside 172.10.1.0 255.255.255.0 172.10.2.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 172.0.0.0 255.0.0.0 inside
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-aes-256 trmset1, esp-sha-hmac
Crypto-map dynamic map2 10 set transform-set trmset1
map map1 10 ipsec-isakmp crypto dynamic map2
client authentication card crypto LOCAL map1
map1 outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 encryption aes-256
ISAKMP policy 10 sha hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address voicelabpool pool cuclab
vpngroup dns 204.x.x.10 Server cuclab
vpngroup cuclab by default-field voicelab.com
vpngroup split tunnel 101 cuclab
vpngroup idle 1800 cuclab-time
vpngroup password cuclab *.
Telnet timeout 5
SSH 208.x.x.11 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 172.10.1.2 255.255.255.255 inside
SSH timeout 60
Console timeout 0
username labadmin jNEF0yoDIDCsaoVQ encrypted password privilege 2
Terminal width 80
Cryptochecksum:b03a349e1ac9e6022432523bbb54504b
: end
Try to turn on NAT - T
PIX (config) #isakmp nat-traversal 20
http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#Solution1
HTH
-
CANNOT ACCESS THE LAN WITH THE EASY VPN CONFIGURATION
Hello
I configured easy vpn server in cisco 1905 SRI using ccp. The router is already configured with zone based firewall. With the help of vpn client I can reach only up to the internal interface of the router, but cannot access the LAN from my company. I need to change any configuration of ZBF since it is configured as "deny everything" from outside to inside? If so that all protocols should I match? Also is there any exemption of NAT for VPN clients? Please help me! Thanks in advance.
Please see my full configuration:
Router #sh run
Building configuration...Current configuration: 8150 bytes
!
! Last modification of the configuration at 05:40:32 UTC Wednesday, July 4, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
router host name
!
boot-start-marker
boot-end-marker
!
!
Passwords security min-length 6
no set record in buffered memory
enable secret 5 xxxxxxxxxxx
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login ciscocp_vpn_xauth_ml_1 local
AAA authorization exec default local
AAA authorization ciscocp_vpn_group_ml_1 LAN
!
!
!
!
!
AAA - the id of the joint session
!
!
No ipv6 cef
IP source-route
no ip free-arps
IP cef
!
Xxxxxxxxx name server IP
IP server name yyyyyyyyy
!
Authenticated MultiLink bundle-name Panel
!parameter-map local urlfpolicy TSQ-URL-FILTER type
offshore alert
block-page message "Blocked according to policy"
parameter-card type urlf-glob FACEBOOK
model facebook.com
model *. Facebook.comparameter-card type urlf-glob YOUTUBE
mires of youtube.com
model *. YouTube.comparameter-card type urlf-glob CRICKET
model espncricinfo.com
model *. espncricinfo.comparameter-card type urlf-glob CRICKET1
webcric.com model
model *. webcric.comparameter-card type urlf-glob YAHOO
model *. Yahoo.com
model yapoparameter-card type urlf-glob PERMITTEDSITES
model *.parameter-card type urlf-glob HOTMAIL
model hotmail.com
model *. Hotmail.comCrypto pki token removal timeout default 0
!
Crypto pki trustpoint TP-self-signed-2049533683
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2049533683
revocation checking no
rsakeypair TP-self-signed-2049533683
!
Crypto pki trustpoint tti
crl revocation checking
!
Crypto pki trustpoint test_trustpoint_config_created_for_sdm
name of the object [email protected] / * /
crl revocation checking
!
!
TP-self-signed-4966226213 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02111101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43647274 31312F30
69666963 32303439 35323236 6174652D 3833301E 170 3132 30363232 30363332quit smoking
encryption pki certificate chain tti
for the crypto pki certificate chain test_trustpoint_config_created_for_sdm
license udi pid CISCO1905/K9 sn xxxxxx
licence start-up module c1900 technology-package datak9
username privilege 15 password 0 xxxxx xxxxxxx
!
redundancy
!
!
!
!
!
type of class-card inspect entire tsq-inspection-traffic game
dns protocol game
ftp protocol game
https protocol game
match icmp Protocol
match the imap Protocol
pop3 Protocol game
netshow Protocol game
Protocol shell game
match Protocol realmedia
match rtsp Protocol
smtp Protocol game
sql-net Protocol game
streamworks Protocol game
tftp Protocol game
vdolive Protocol game
tcp protocol match
udp Protocol game
match Protocol l2tp
class-card type match - all BLOCKEDSITES urlfilter
Server-domain urlf-glob FACEBOOK game
Server-domain urlf-glob YOUTUBE game
CRICKET urlf-glob-domain of the server match
game server-domain urlf-glob CRICKET1
game server-domain urlf-glob HOTMAIL
class-map type urlfilter match - all PERMITTEDSITES
Server-domain urlf-glob PERMITTEDSITES match
inspect the class-map match tsq-insp-traffic type
corresponds to the class-map tsq-inspection-traffic
type of class-card inspect correspondence tsq-http
http protocol game
type of class-card inspect all match tsq-icmp
match icmp Protocol
tcp protocol match
udp Protocol game
type of class-card inspect correspondence tsq-invalid-src
game group-access 100
type of class-card inspect correspondence tsq-icmp-access
corresponds to the class-map tsq-icmp
!
!
type of policy-card inspect urlfilter TSQBLOCKEDSITES
class type urlfilter BLOCKEDSITES
Journal
reset
class type urlfilter PERMITTEDSITES
allow
Journal
type of policy-card inspect SELF - AUX-OUT-policy
class type inspect tsq-icmp-access
inspect
class class by default
Pass
policy-card type check IN and OUT - POLICIES
class type inspect tsq-invalid-src
Drop newspaper
class type inspect tsq-http
inspect
service-policy urlfilter TSQBLOCKEDSITES
class type inspect tsq-insp-traffic
inspect
class class by default
drop
policy-card type check OUT IN-POLICY
class class by default
drop
!
area inside security
security of the OUTSIDE area
source of security OUT-OF-IN zone-pair outside the destination inside
type of service-strategy check OUT IN-POLICY
zone-pair IN-to-OUT DOMESTIC destination outside source security
type of service-strategy inspect IN and OUT - POLICIES
security of the FREE-to-OUT source destination free outdoors pair box
type of service-strategy inspect SELF - AUX-OUT-policy
!
Crypto ctcp port 10000
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 2
Group 2
!
ISAKMP crypto client configuration group vpntunnel
XXXXXXX key
pool SDM_POOL_1
include-local-lan
10 Max-users
ISAKMP crypto ciscocp-ike-profile-1 profile
vpntunnel group identity match
client authentication list ciscocp_vpn_xauth_ml_1
ISAKMP authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-model 1
!
!
Crypto ipsec transform-set TSQ-TRANSFORMATION des-esp esp-md5-hmac
!
Profile of crypto ipsec CiscoCP_Profile1
game of transformation-TRANSFORMATION TSQ
set of isakmp - profile ciscocp-ike-profile-1
!
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
!
interface GigabitEthernet0/0
Description LAN INTERFACE-FW-INSIDE
IP 172.17.0.71 255.255.0.0
IP nat inside
IP virtual-reassembly in
security of the inside members area
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
Description WAN-INTERNET-INTERNET-FW-OUTSIDE
IP address xxxxxx yyyyyyy
NAT outside IP
IP virtual-reassembly in
security of the OUTSIDE member area
automatic duplex
automatic speed
!
interface Serial0/0/0
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
no fair queue
2000000 clock frequency
!
type of interface virtual-Template1 tunnel
IP unnumbered GigabitEthernet0/0
ipv4 ipsec tunnel mode
Tunnel CiscoCP_Profile1 ipsec protection profile
!
local IP SDM_POOL_1 172.17.0.11 pool 172.17.0.20
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP nat inside source list 1 interface GigabitEthernet0/1 overload
IP route 0.0.0.0 0.0.0.0 yyyyyyyyy
IP route 192.168.1.0 255.255.255.0 172.17.0.6
IP route 192.168.4.0 255.255.255.0 172.17.0.6
!
access-list 1 permit 172.17.0.0 0.0.255.255
access-list 100 permit ip 255.255.255.255 host everything
access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
access-list 100 permit ip yyyyyy yyyyyy everything
!
!
!
!
!
!
!
!
control plan
!
!
!
Line con 0
line to 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
transport input ssh rlogin
!
Scheduler allocate 20000 1000
endA few things to change:
(1) pool of IP must be a single subnet, it is not the same subnet as your subnet internal.
(2) your NAT ACL 1 must be changed to ACL extended for you can configure NAT exemption, so if your pool is reconfigured to be 10.10.10.0/24:
access-list 120 deny ip 172.17.0.0 0.0.255.255 10.10.10.0 0.0.0.255
access-list 120 allow ip 172.17.0.0 0.0.255.255 everything
overload of IP nat inside source list 120 interface GigabitEthernet0/1
No inside source list 1 interface GigabitEthernet0/1 ip nat overload
(3) OUT POLICY need to include VPN traffic:
access-list 121 allow ip 10.10.10.0 0.0.0.255 172.17.0.0 0.0.255.255
type of class-card inspect correspondence vpn-access
game group-access 121
policy-card type check OUT IN-POLICY
vpn-access class
inspect
-
Just upgraded to El Capitan and cannot access the calendar. It opens with a message 'Moving calendars to the server.
I cannot access all features and can be closed only by using force quit.
Please stop calendar and also the application of reminders, runs. Force quit if necessary.
Back up all data.
If you synchronize some of your calendars, or reminders with iCloud, then in the iCloud preferences window, uncheck that marked calendars and reminders. You will be prompted to confirm that you want to remove your iCloud calendars and reminders of the computer. They will always be in iCloud. Re-check the boxes.
If you synchronize agendas or reminders with another network such as Google service, please open the preferences panel Internet accounts. Make a note of the settings for calendar accounts, then delete and recreate.
Launch schedule and see if there is an improvement.
-
Hello
I have a Windows 2003 X 64 server and since a week ago everything works fine.For a week or two when I try to run an X 86 application, I always get this error:"Windows cannot access the specified device, path or file.If I run a x 64 apps everything works fine.What made a mistake?Thank youHello
Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet. Please post your question in the TechNet forums. You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en/category/WindowsServer/
-
How can I get my email on when I get the above message
Cannot access the url reqested due tosystem error on this server
Apparently, there is a problem on the mail server. Contact technical support for your email provider. MS - MVP - Elephant Boy computers - don't panic!
-
I am faced with a kind of strange and unusual error. in my office, the internet is accessible with the proxy server. without him we cannot access the internet. However, there is a laptop computer on which some time the internet is accessible only when I leave the proxyserver only on that machine... any idea?
Hello
Work on a domain environment?
Changing the proxy settings is something that you usually only have to do if you connect to the Internet via a corporate network. By default, Internet Explorer automatically detects proxy settings. However, you may need to manually set a proxy with information supplied by your network administrator.
If you are on a domain environment then please post the question on the link mentioned below using:
http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads -
When I install Oracle Grid Infrastructure 12 c Release 1 (12.1.0.1.0), I have the following error:
Failure of the initial installation of INS-30131 required for execution of the controls of the installer cannot access the temporary location
Cause:-unable to access the temporary location
Action - make sure that the current user has required permissions to the temporary location
Details of the addition
-GLWB-1560: "/tmp/" temporary directory path is shared on the nodes '... »
The oracle user I use is to have access in / tmp, I did a test by creating a file here.
Any idea?
Thank you
This is the description of the error, I saw, but he was trying to find an idea how to solve this problem.
Anyway, I solved it by renaming the Group of volumes and accordingly update the fstab and the grub.conf.
Thank you
Eugen
-
Cannot access the server message coming up and cannot convert files
Cannot access the server message coming up and can't convert the files. Works on my desktop, but not at home.
ER
Is it ExportPDF?
-
BI SampleAppFiles Server cannot access the correct file
Hello experts,
Part of my project is creation of KPIs for my clients. Before doing all this, I'm trying to create a KPI sample and see if it works well. It is using 11g (1.1.7).
Here's the problem: I created the sample KPI without problem; However, when I try to open the report I get an error that
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error occurred. [nQSError: 43113] The message returned by OBIS. [nQSError: 64023] Cannot access the E:\BIHOME\instances\instance1\bifoundation\OracleBIServerComponent\coreapplication_obis1/sample/SampleAppFiles/Data/SAMP_REVENUE_A.xml: no such file or directory for table SAMP_REVENUE_A (HY000)
The path is correct, except instead (E:\), it should be (C:\). Does anyone know how to change this? Help, please.
I don't have a 'E' drive in my system. This forum works on windows
Help, please
Hello
In the sample OBIEE, you have a variable called BI_EE_HOME with this path
To change this, open your SPR (online mode) and then change repository variable BI_EE_HOME
We call this variable in your connection pool (you can change this path directly on the connection pool too)
Felipe Idalgo
-
Hi I encounter an error message "Windows cannot access the specified device, path or file. You don't have appropriate permissions to access. »
The error message every time I click on administrative tools of the window (including the Control Panel, windows update, the Windows Explorer, etc.) but without impact on other programs I have.
I rebooted in safe mode and discover that everything works fine (no error message will appear when you click on window management tools).
I proceed to do a clean boot-> first disable all services of third parties (message yet to come), and then clear the components of the service windows (message yet to come)
I tried to type "explorer.exe" in the start menu-> search field then click right highlight to run with administrative rights, then received another message of error "Server execution failed".
I am the administrator account on this PC - and have full access.
The error seems to have appeared on 11 August after Windows Update the following:
Update of security for Microsoft Windows (KB2536276, 2556532 2559049, 2560656, 2563894, 2567680), and
Update for Microsoft Windows KB2563227
A security update for the Microsoft.net framework 4 client profile (verson 1)
There is no installation of any software or updates outside the windows update.
I also tried to restore the windows before August 10, 2011, but that did nothing.
As the error prevents me to access any object Admin window - I'm unable to retrieve the product ID and write to Microsoft Tech and ask for help.
I hope some of you can offer the suggestion of possible solutions (I really want to re - install window 7 and other software, I'm sure).
Thank you.
My solution works in about 2 minutes, it's a very weird error and only happened to 3 jobs in the last 3 years, this solution does not need to create another account if local administrator is active and allows access to the corrupt user documents ect.
Log in as the local administrator or a domain administrator
If the local administrator is not activated refer to http://support.microsoft.com/kb/555910 and after completing these newspapers of steps on the local administrator account.
Locate the user for example files. C:\Users\[username]\
If you see no AppData press Alt to see the toolbar at the top of the window, select Tools > folder options, go to the view tab and select "Show hidden files, folders and drives" click OK.
Go to AppData\Local
Select all (Ctrl + a).
Delete
* Do not delete credentials (as it will remove their wallpaper) *.
This allows to release the error.
-
We have implemented a cluster and our hosts, added vmkernel and have the right licenses. The migration option is available, but then we get the error message "cannot access the virtual machine configuration: cannot access the file [storage]" I thought about is because they do not work on a shared storage...
I had to think about iSCSI, but have not tried it before, and now I ask you, is the most optimal solution? We will cable from the server to the top with a SAS cable,
The servers are located in different parts of the building, I could put the other to the first server and their cable it but to avoid this, is there another solution? I can't use the data storage "migrate" since I don't have essential vmware more...
you need external shared storage and follow the right cable FC, iSCSI, or SAS. You can not just a two-server cable upward with a SAS cable and expect it to work like the discs are still local only. the other option is to search for virtual storage in which transform your disks local shared iSCSI volume
-
Hello!
So I'm at the end of my rope with this one... it lasts for months, and I keep revisitng every two weeks to try and fix that and every time to be completely frustrated. I found this forum tonight, so here goes...We downloaded a few games on the HP Games Web site. We download them and everything works fine. Then, we will open the games and this pop up error message:
"Windows cannot access the specified device, path or file. You can not have the appropriate permissions to access the item.These games used to run fine, and I have no idea why they now have problems. We have a Vista operating system, 1 account who is the administrator, the Parental control is disabled (or if we believe).
If anyone can please help it would be much appreciated! We have a monthly membership to this site of game and continue to accumulate credits, but may not use it. It makes us crazy!
Thank you in advance!
Hello Heathie,
Thank you for posting. It seems that the program is no longer on your computer. This can happen if the game files are deleted, but the game itself has not been uninstalled correctly. I recommend you to download the game again to a location on your computer where you can easily find and install it. This should fix the problem.
Please let me know if this helps you.
Zack
Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think. -
Jpg file printing - windows cannot access the specified device, path, file
Original title: I have a similar problem, I can open the jpg fine, I can't print it
I have a similar problem, I open the jpg fine, I can't print it, permissions are fine. I get the same erorr-windows cannot access the specified device, path, file...
Hi Janine.
1. are you able to print documents?
2. the problem occurs only with a particular image file?
3. how the printer is connected to the computer?
4. What is the brand and model of the computer and the printer?
5. have you logged as administrator?
Method 1:
First of all, try to print a test page and check if it works:
To print a test page
Method 2:
I suggest you check out the link to use the System File Checker tool (SFC) to troubleshoot missing or corrupted system files in Windows:
Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)
Note: you must have the Windows XP disc to make the SFC scan.
Method 3:
I suggest you to turn off all third-party security software and the Windows Firewall and then try to print the file:
How to change or remove a program in Windows XP
http://support.Microsoft.com/kb/307895
How can I turn on or turn off the firewall in Windows XP Service Pack 2 or later versions?
http://support.Microsoft.com/kb/283673
Note: run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.
Let us know the results.
Maybe you are looking for
-
I just got a Thinkstation S20 with preinstalled Vista Business and no XP install cd, just a DVD of drivers. I did the all HARD disk controllers floppy I could find on this dvd and I tried to install XP by pressing F6 and installing the storage driver
-
Not be able to use gmail and yahoo mail
I have problems connecting to my email yahoo & gmail.
-
IMPOSSIBLE TO INSTALL ANTIVIRUS SOFTWARE
Recently, I uninstalled NORTON INTERNET SECURITY to my laptop but I did not remove my Norton settings (this is an option during the uninstall process). After that I downloaded Avast Home, but I could not register the software (I thought that somethin
-
When I create a list of the contact group, how can I avoid all these names also appear in my contact list individually? I just want the name of 'group' is displayed. Otherwise, many contacts on my list twice and my contact list is too long.
-
Limitations of email to Contacts?
HelloEach contact should not receive more than 2 emails in 1 week. How do we that?Thank you!