Cannot capture with Premiere CS6 with canon XA20

Similar Questions

• Cannot communitcate with Canon MP530 after upgrade to El Capitan

  iMac (27 inch, mid 2011)

  10.11.5

  Canon MP530

  I just upgraded to El Capitan yesterday, the printer was fine yesterday morning.

  New drivers not available from Canon.

  When you try to add the MP530, I get a dialog box saying "an error occurred while trying to add the selected device.  Cannot communicate with the printer at this time. »

  Any ideas?

  If you haven't already done so, try to reset the printing system.

  Reset the printing system - OS X El Capitan

• Cannot capture hdv with Premiere Pro

  I'm having a hard time capturing video from my camcorder high definition of Sony HDV - HC7. I am running Premiere Pro CS4 on a DellStudio running under Win 7 64 bit Ultimate system. It has a processor intel i7 CPU (8 cores) with 12 g of RAM.
  
  When I run first and select Capture it opens the capture window properly and allows me to control the camcorder. The camera is connected and working. However, it will not capture. I tried to capture several ways:
  
  1 connect the entry points and on the tape and then do a batch capture.
  2. Enter the whole band.
  3. manually press record at the correct stage is spotted on the camcorder.
  
  Each time the result is the same, nothing is captured. The meter reading displays the band plays and I can see the band playing, but the length of the recorded scene remains at 00:00:00
  
  I am connected via (camera) 4-pin to 6-pin (computer) via firewire. I tried two different firewire cables to ensure that it is not a cable problem. I don't have a capture card dedicated unless my Hauppauge Win TV HVR-1250 can be considered as a capture card. My firewire is out of the system tray, so I did not have a dedicated in system firewire card.
  
  I went through Adobe troubleshooting advice and none of these options helped.

  1. my hardware meets the minimum requirements

  2. recreate (even reinstall) cache does not help.

  3. I have tried two different bands with the same problem

  4. the connection cables work. I even tried two different firewire cables. The two show an iLINK on the camera connection and the capture window can control the playback of the camera without any problems.

  5 scene Detect is grey so I can't turn off, but I don't think it plays a role in the HDV capture.

  6. I checked my device control settings. The unit is set to sony and 1 alternate. I put it this way because I could not capture anything on the standard. I tried this setting and have captured a clip. After that, I could capture is no longer on the new setting. Even though I'm set to Standard or its replacement, the status of the camera is online.

  7 capture with another utility. I tried the software to capture from sony as well as first elements 8.0 and I have the same problems.

  8. make sure that all of the video was made. They are.

  9. Select playback (set to auto) settings.

  10. I'm logged on as an administratore

  11. I don't have a capture card. Do I need one?

  13. I run it with no other current main program execution.

  14. all my drivers are up to date.

  15. my video card driver is current.
  
  I must add that I have the same problem, try other software like Premiere Elements 8.0 and Sony Picture Motion Browser, so I think it's a hardware problem.
  
  I appreciate any suggestions. Do I need a dedicated video capture card? If so, what do you suggest me? Do I need a Firewire 4 pin, rather than a 6 port pins? Do I need a dedicated sony cable as suggested in some forums?
  
  Thanks in advance.
  
  wcameron

  my gut feeling is that the built-in firewire is not good. but before part you with little money for a PCIe version, it is possible, that you can test the device on another computer? just to rule out the camera itself.

  try to avoid really cheap FW cards. I envy those who have a TI chipset, but it's just anecdotal.

  MP

• Canon PIXMA MP160 error message 'cannot communicate with scanner.

  I have a Canon PIXMA MP160, who worked during the scanning of the printer on my computer. Now, I get an error message "cannot communicate with scanner. Installation scanner no longer works. The Canon site suggested looking in the Windows directory for a file named ' USBSCAN. SYS, but my research has not found it

  Installation scanner said that all the files are in place until it reaches the end.

  I received an update of windows on 31/10/2011. It works

• I'm trying to uninstall Cs6 master collection and I can't because this information is displayed ERROR: DW040: the product '{E8AD3069-9EB7-4BA8-8BFE-83F4E69355C0}' is not installed. Cannot proceed with the uninstall. How can I solve this problem?

  I'm trying to uninstall Cs6 master collection and I can't because this information is displayed ERROR: DW040: the product '{E8AD3069-9EB7-4BA8-8BFE-83F4E69355C0}' is not installed. Cannot proceed with the uninstall. How can I solve this problem?

  Hi Paulov53532347,

  Try to use the cleanup for the same tool: use of the Adobe Creative Cloud cleaning tool to solve installation problems

  Let us know if that helps.

• Can I capture with Final Cut Pro and edit in Premiere Pro?

  Because it appears first has problems with capture - at least for me, but as I see it for others as well - and I can capture with iMovie, I take it with Final Cut Pro for capture - cross for Adobe Premiere and the suite for editing, then finalized? Or is it a problem to copy the photos/files from one program to the other (they would be clearly identified if I could just import first shots later?)

  Thank you

  Rob

  Hi Rob,

  When you are capturing HDV into FCP, it creates a specific Apple HDV codec. It is a codec that is not available unless the FCC, movement or compressor is installed.

  Two solutions of workaround would be to use Premiere Pro on Mac with above mentioned applications on the same system or convert a codec which can be read in first.

  Best,

  Peter Garaway

  Adobe

  First pro

• How to make a capture of Premiere Pro CS4 with scene detect in HDV from a SONY HVR M15U deck?

  News of the computer:

  Windows 7 64 bit

  PC ACPIx64

  Xenon (R) Intel (r) CPU x 5650 @2. 67 GHz 2.67 Ghz

  24.0 GB of RAM DDR3 memory

  Hard drives: C drive is mirror 2 x 500 GB SATA - operating system, programs, windows VM, 387 GB free

  M drive: 1 TB SATA 901 GB of video files free media player

  N drive: 1 TB SATA 929 GB free trailers video & audio media player

  Video card: bus NVIDIA Quadro FX 3800 4 PCI, device 0, function 0 driver 8.15.11.9038

  DVD/CD Rom drive: Optiarc DVD RW AD - 7260S

  IEEE 1394: Texas Instruments OHCI

  Audio device high definition

  Virtual memory: 24567 MB Windows chose what is best

  Adobe Production Premium CS4 - first Pro 4.2.1

  Other programs installed

  NERO 9 Multimedia

  CCleaner

  CPUID

  Microsoft Security Essentials

  Name of the OS Microsoft Windows 7 Ultimate

  Version 6.1.7600 Build 7600

  Another Description of OS not available

  OS manufacturer Microsoft Corporation

  Name of the system SUPEREDIT

  System manufacturer Supermicro

  System model X8SAX

  Type of system PC x 64

  Processor Xeon of Intel (r) CPU X 5650 @ 2.67 GHz, MHz, 6 Lossnay 2668, 12 or logical processors

  Version of the BIOS/Date American Megatrends Inc. 1. 1A, 29/04/2010

  SMBIOS Version 2.6

  Windows directory C:\Windows

  System directory C:\Windows\system32

  Boot device \Device\HarddiskVolume1

  Locale United States

  Layer of HAL Version = "6.1.7600.16385".

  Username SuperEdit\Michel

  Zone Pacific daylight time

  Physical memory (RAM) installed GB 24.0

  Total physical memory GB 24.0

  Available physical memory 21.9 GB

  Total virtual memory 48.0 GB

  Available virtual memory 45.8 GB

  File of the page space GB 24.0

  Swap file C:\pagefile.sys

  Unable to capture HDV. Unable to capture from a Sony HVR M15U or directly from a Canon XH - A1 or Canon XL - H1 via one cable 1394. Project settings: Capture HDV.

  Parameters:

  M video capture: video capture,

  M: Audio captured audio capture,

  Audio video previews N: video and an Audio excerpt

  The sequence settings: reading: external device: zero, conversion of image format: audio systems Hardware, disable video output in the background, default settings for the General settings.

  The remote control: the remote control DV/HDV

  When I click on change capture settings: Capture format: HDV and HDV settings click the highlight of the yellow border lights, but no window opens. Why a window opens with the settings?

  I can control the HVR M15U, see and hear the video playback, but when I click on the record button, the screen becomes a blue screen with the rules of the game on the video material (what?) text on the screen and no audio. I don't have the ability to detect scene. It records the audio and video in a long clip (blind faith just is the recording and I do not have something for the blind).

  I have an another editing system with Windows 7 64-bit CS4 Production Premium with a Matrox RT - X 2 card. When I connect the HVR-M15U to this system, I can see and hear the recording as it is captured, with scene detect the work.

  My goal is to make this new system works without a Matrox RT - X 2 card. Where can I change the settings in order to see and hear what is recorded? How can I also get the scene detection to work? I made the change of compatible host OHCI 1394 controller (legacy), but that has not changed anything.

  Are there settings to see and hear the video as it is registered?

  Use HDVSplit. Much better than the CS4 PR, offer scene detection, avoids errors OOS (out-of-sync), gives an extract and is free.

• I have download Adobe Premiere CS6 in the trial with the CC, but it doesn´t install the program so I launch can´t.

  I have already downloaded Adobe Premiere CS6 Adobe Creative cloud, but it downloads the program but doesn´t install it.

  Who does not respect the conditions... you MUST have a 64-bit operating system

• 1065984 error during installation or capture with sp4 4.6 HPDM

  Hello

  Yesterday, I did the update to sp3 HPDM 4.5 to 4.6 sp4.

  Now, I can not install image of wes or capture on my computer thinclient t5740e.

  Can I install the update agent, the agent is the last (4.6.3660.21244).

  This newspaper to install and capture (with the french):

  Install:

  2014-11-13 14:08 mapping of the repository to: master repository
  2014-11-13 14:08 sent the job to the managed devices management gateway
  2014-11-13 14:08:04 the task has been retrieved by the agent.
  2014-11-13 14:09:09 [error code: {0}] [Module: {1}] [category: {2}]
  2014-11-13 14:09:09 [error details]: \Ndm\branches\Release_4.6.4\Source\Cpp\Agents\Core\Task\wins\ImageTask_XPE.cpp@286: cannot download the image customer kit.
  \Ndm\branches\Release_4.6.4\Source\Cpp\Agents\Core\Task\common\ImageCommon.cpp@601: cannot download the image map file, file name: toolsConfig.xml
  \Ndm\branches\Release_4.6.4\Source\Cpp\Agents\Core\Task\common\ImageCommon.cpp@560: cannot download the mapping file.
  .\port_layer\ftpclient\fileclient.cpp@179: could not get the remote file LocalDir:C:\,RemoteDir:\\172.22.22.86\Repository/Repository/Tools/Imaging/Mapping,Name:toolsConfig.xml
  .\port_layer\ftpclient\ShareFolderClient.cpp@442: could not get the size of dir.
  .\port_layer\file_io\dirfuncs.cpp@845: failed to get the data from the file.
  .\port_layer\file_io\filefuncs.cpp@86: could not get the data of the file & colon;\\172.22.22.86\Repository/Repository/Tools/Imaging/Mapping\toolsConfig.xml
  .\port_layer\file_io\filefuncs.cpp@84: the specified path is not found.
  2014-11-13 14:09:09 failed to run the common task.

  Capture:

  2014-11-13 16:21:43 sent the job to the managed devices management gateway
  2014-11-13 16:21:47 the task has been retrieved by the agent.
  2014-11-13 16:22:51 [code error: {0}] [Module: {1}] [category: {2}]
  2014-11-13 16:22:51 [error details]: \Ndm\branches\Release_4.6.4\Source\Cpp\Agents\Core\Task\wins\ImageTask_XPE.cpp@118: cannot download the customer kit.
  \Ndm\branches\Release_4.6.4\Source\Cpp\Agents\Core\Task\common\ImageCommon.cpp@601: cannot download the image map file, file name: toolsConfig.xml
  \Ndm\branches\Release_4.6.4\Source\Cpp\Agents\Core\Task\common\ImageCommon.cpp@560: cannot download the mapping file.
  .\port_layer\ftpclient\fileclient.cpp@179: could not get the remote file LocalDir:C:\,RemoteDir:\\172.22.22.86\Repository/Repository/Tools/Imaging/Mapping,Name:toolsConfig.xml
  .\port_layer\ftpclient\ShareFolderClient.cpp@442: could not get the size of dir.
  .\port_layer\file_io\dirfuncs.cpp@845: failed to get the data from the file.
  .\port_layer\file_io\filefuncs.cpp@86: could not get the data of the file & colon;\\172.22.22.86\Repository/Repository/Tools/Imaging/Mapping\toolsConfig.xml
  .\port_layer\file_io\filefuncs.cpp@84: the specified path is not found.
  2014-11-13 16:22:51 cannot run the common task.

  Please, help me! I don't know what I can do.

  Best regards.

  It seems that the shared folder was not well configured.

  Could you please download the controller.conf under masterrepository folder and take a screenshot of the master repository configuration dialog box?

• MG6120 - cannot scan error "cannot communicate with scanner.

  Hi, I have a Mac Book Pro with OS 10.10.5 (Yosemite).  I have the Canon MG6120 printer.  Since I updated to Yosemite, I'm more able to scan using the MP Navigator ex software  I get the following error message:

  "Cannot communicate with the scanner.

  Cable may be disconnected or scanner may be turned off.

  Check the status.

  Scanner driver will be closed.

  2.1.0.

  The only way I can scan is by using the touchpad on the printer and saving the scan on a USB key.

  I went to the page support and downloaded the latest drivers, but he has not made a difference.  I need to remove the printer and re - add again?

  You will appreciate greatly any help or advice.

  Thank you very much

  Alice Berman

  Hello.

  If the printer is used via the USB port, make sure that the printer is connected directly to your computer.  Avoid using USB hubs or extension to connect devices.

  If the printer is used with wireless, please proceed as follows to save your scanner to work wireless on Mac:

  1. click on the "Canon IJ Scan Utility" icon on the top of your screen and choose "display settings." (Located near the clock, looks like a scanner open with an arrow below). For the latest operating systems, the program can be located in the Canon Utilities listing applications.

  2. in the next screen, make sure that the network version of the printer is selected instead of "do not use". The network version will be a long series of numbers next to him.

  3. click on "Scan-of-operation-panel-settings".

  4. a new window should appear, make sure that the printer is selected, and then click OK.

  5. click OK to exit the utility.

  Once done, do the following:

  1. open the Application folder.

  2. open Canon Utilities.

  3. open MP Navigator.

  4. Once opened, click on the "Settings/preferences" button at the bottom.

  5. in the menu drop-down "Product name", select the Network Scanner.

  6. click OK at the bottom.

  Once done, try to scan from MP Navigator.

  If you continue to have difficulties, find more help contact us.

• Video capture with windows movie maker capture 16:9 dv camcorder.

  My Canon DV camcorder using Windows Video Capture video capture is not capture video in 16:9 format, 4:3 looks like. Why?

  Hello

  Thanks for posting your query in the Microsoft Community Forums!

  If I understand you correctly, you have a problem with the video capture from a camcorder DV Canon using windows movie maker. I understand it must be frustrating, but don't worry, we're here to help solve your problem and guide you in the right direction.

  The proportions of the original video on the videotape. Depending on your DV camera and the camera at the time settings wherever you saved the original video tape, your video can be recorded to an aspect ratio of 16:9 (wide screen) or 4:3 (standard). Choose a video format and a report l / h in video import, which is the same as the video recorded on tape.

  For more information:

  Video import settings: frequently asked questions

  http://Windows.Microsoft.com/en-in/Windows-Vista/video-import-settings-frequently-asked-questions

  For your reference:

  Troubleshoot importing video problems

  http://Windows.Microsoft.com/en-in/Windows-Vista/Troubleshoot-importing-video-problems

  Import video from a videotape

  http://Windows.Microsoft.com/en-in/Windows-Vista/import-video-from-a-videotape

  It will be useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• Scanning with Canon PIXMA MX870 all-in-One printer using Windows 7 64 bit

  The computer is unable to recognize the scanner.  The message I get is "cannot communicate with scanner for these reasons - scanner is turned off - scanner is disconnected." Code 2,145,50 "impression is generally OK.  Help.

  Have you tried canon support?

  http://www.USA.Canon.com/Cusa/consumer/products/printers_multifunction/office_all_in_one_inkjet_printers/pixma_mx870#ServiceAndSupport

• I have a problem with Canon PowerShot SX 60 Hs-camera with Camera Raw, I can not open the photos taken in raw mode. How can I update Camera Raw? I also tried with Photoshop elements 13, but it was the same thing, I could not open pictures.ts 13 gross

  I have a problem with Canon PowerShot SX 60 HS-vamera wirh Camera Raw in Photoshop elements 12, cannot open raw files. I have the latest version of camera Raw plug in, what is the problem?

  It's on our radar and hoping to incorporate it in a next update.

  As soon as it is available, it will be updated in the article.

  http://helpx.Adobe.com/Creative-Suite/KB/camera-raw-plug-supported-cameras.html

  ~ David

• First Pro CS5 does not not after 55 minutes of capture with intensity shuttle

  Hi and thanks for the valuable resources on this forum.

  I'm analog video capture in first Pro CS5 it using the shuttle Blackmagic intensity (with corrector time basis in the path of the video).  My shots are stopped at 54 or 55 minutes when the computer becomes inadmissible.  What happened with the codec Blackmagic movement as well as jpeg YUV 10 bit capture. Same thing if I capture with express media (blackmagic capture software)

  I tweaked my system according to the many recommendations in the forum.

  Running CS5 5.03, backup 10 minutes automatic (same problem without automatic recording or automatic check in at 20 minutes)

  Windows 7 64 bit fully up-to-date

  I7 - 930 cpu

  Gigabyte x58A - UDP5 (revision 1)

  24 GB Ram

  NVIDIA 470 - MSI twin Frozr cooling solution.

  Restore off, windows search indexing

  Followed advice from the forum and Viper about optimization system

  3 hard drives

  System on standard Sata 2 drive

  The capture of SSD drive from OCZ Vertex 3 120 g (beautiful piece of gear) of the project currently running on the Sata 3 controller

  Pagefile on another hard drive

  Uninstalled Norton 360

  Anything else I could find uninstalled or disabled.

  Firmware and latest drivers for USB of the Station pilot as recommended by Blackmagic.

  Capture of the very successful things less than 55 minutes, but I have things any longer I would like to capture at once.

  I used process Explorer to watch what is happening.  Nothing special that I can identify in terms of process, but cpu seems to be 100%.

  With the progressive settings problems remain the same.

  I'm not aware of any limit of size of file with Premiere Pro or Blackmagic - is there some?

  Whereas reinstall but would be grateful to all points of view.  My first post so I hope that I have provided good info to help me help you.

  Thank you

  Andrew

  As happens with the BM software as body, I will GUESS that the problem is with the pilot BM device that links software appliance

  I would check to see if they have a difficulty with BM

• 1st generation Apple TV cannot connect with the apple ID

  Have 1st Generation apple TV and recently cannot connect with my apple ID.

  The reset several times and nothing.

  Help?

  You have activated 2 no authorization of your Apple ID? If so, disable the connection from a browser and temporarily, then connecting ATV, then reactivate. If not, please describe what is happening when you try to connect. What message do you have?