Cannot use join homegroup, no button "join"

Similar Questions

• My computer is on a network, but Windows 7 (Pro x 64) shows that it is not. Cannot change network location to home. Cannot use the homegroup.

  I'm putting my network (with homegroup) home, but when I go into control panel > network and Internet > homegroup, it says:

  "This computer cannot connect to a homegroup." Then,

  "To create or join a homegroup, network location of your computer must be on home."

  Okay so. I go to network and sharing Center and click on "connect to a network" and I get a box in the lower right corner that says "no connection available.

  I find that strange, because when I click on 'My Computer', I see in the left pane all the computers in my house under 'Network'... so I'm in network... but I'm not?

  It is a problem because until I am able to add this computer, I am unable to share the data on this computer and it is my office alone AND the pc is connected to my router.

  I can not access my storage drive. I can't stream media.

  All opinions are appreciated. Thank you.

  Hello

  Check the Device Manager for the entry of valid card of the wire.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a Local Area Connection icon/entry, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Connect you to the menu of the router from a work computer and make sure DHCP is on, and it is configured to assign IPs which can cover the number of computers that are connected (a bit more will be even better).

  Turn off the computer and the router, reset the router and the computer.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  It still does not work, try this too.

  Firewall software.

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall Windows Firewall should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly, or uninstall it completely allowing the clean flow of traffic on the local network. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Reset the network stacks .

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP, just replace the command typed with.

  netsh int ip reset

  Restart the computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Satellite L850 - cannot use the FN (function) button to turn wireless on

  I have a Toshiba Satellite L850 PSKDLA-0D100R. My problem is what is stated in the subject. I tried to reinstall windows, that did not work, I tried everything I found concerning this problem on google and none of this helped then please help me! The 'flash cards' I think they are called do not come to the top when I press 'FN F12' to turn on without thread, even if they do not work when you adjust the brightness of the screen and the sound.

  Please help me!
  Thank you.

  Usually, this should work if you tried to reinstall the OS using original recovery image that you got with your laptop.

  Have you tried to reinstall Toshiba Value Package?

• How can I use join query ANSI in Forms 10 g

  Dear all,

  How I use the query as mentioned below in Forms 10 g

  SELECT <fields>  
    FROM TableA a INNER JOIN TableB b ON a.key = b.key
  

  Kind regards

  Zafar Iqbal

  You cannot use the SQL commands that did not exist in the 8.0 database.

  Oracle Forms (and reports) has a full PL/SQL engine and (only) the SQL parser.

  However, form (and reports) PL/SQL engine / SQL parser is at a level that was in the Oracle 8.0 database.

  Kind regards

  Zlatko

• Cannot use cards MBNA Web page Services: no account login button appears.

  Cannot use cards MBNA Online Services because no connection of the personal account button appears on the original Web page. However, I can access my MBNA card account using their site of Bank of America. Also cannot reserve National coach Express tickets because no key prosecution appears after have entered my details to the passenger. However, the same site operates using SAFARI. I have FIREFOX 15.0.1.

  Hello

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  Note: This will make you lose all the Extensions, open Web sites and preferences.

  To reset Firefox, perform the following steps:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the button 'Reset Firefox'.
  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  This solve your problems? Please report to us!

• I forgot my PIN for my iPhone and cannot use recovery mode because my sleep button is blocked. A certain predicamnet ik

  I forgot my PIN for my iPhone and cannot use recovery mode because my sleep button is blocked. A certain predicamnet ik

  Only thing you can do is to let die and then hold the home button when you plug it into your computer to put it in recovery mode.

  Actually if the phone is on and that you have an icloud account, you can delete it at distance of icloud.com

  Go to find my iphone and erase the phone.

• Cannot use the Start button

  For some reason, when I try to click on the Start button, it disappears.  I tried all day to dissable addons that sort, but it ended up doing another way.  I have restarted computor, but the Start button, always goes away until I can click on it.  Everyone comes through this before please?

  Hello BeverleyMacKenzie,

  Thank you for the question!

  I'm sorry to know that have problems you with start button. As I understand it, you cannot use the button start effectively.

  Method 1: perform the scan SFC (System File Checker) and see if the problem occurs.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  Method 2: use the Microsoft Safety Scanner in full scan mode and to remove all the threats that is not detected by it and see if the problem persists.

  Microsoft safety scanner

  Note: the Microsoft Safety Scanner expires 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  The Microsoft Safety Scanner is not a replacement for the use of antivirus software that offers continuous protection.

  Answer to us if you have problems with start button or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• creating table using joins in the subquery

  can we create a table using joins in the subquery?
  Like this
  create table emp in select * from employee e, Department d
  where d.department_id = e.department_id
  ??
  We can?

  987018 wrote:
  We can?

  Yes, as long as you column alias names common to both tables to make them unique.

  SY.

• recently, I ran a program that has messed up my settings for the taskbar! now, any program or folder I use shows a small button mini that you cannot read even if someone can help thanks to

  recently, I ran a program that has messed up my settings for the taskbar! now, any program or folder I use shows a small button bar mini tasks that you do not know still can anyone help thank s that it is just a program minimized, I used to be able to read the content now, it is not big enough for an icon

  Hello

  You can check this link:

  Description of the Option "the of the Group similar taskbar buttons".

  http://support.Microsoft.com/kb/281629

• Satellite L25 - after that Windows update is unable to use the Wi - Fi button

  I have a S-1193 Satellite L25, caught a virus, and after a windows update, cannot use wi - fi on the front button.

  What I have to do is disable the adapter, turn it on, then re-boot.
  If I turned off the computer, I di everything again.

  This will make the button work? Or is there a setting that is always on?

  Hello

  > after a windows update, cannot use wi - fi on the front button
  Do you mean the button that launches Internet Explorer?

  According to your message the laptop doesn't connect to the WLan automatically and you will need to connect it manual to get the job of WLan.
  Is this right?

  I put t know how you have connected the laptop to your router, but usually, if you own Windows WLan zero configuration then you should make sure that the parameters to a called + connect when this network is in range. +

  Welcome them

• Qosmio X 300 - this system cannot use Toshiba Accessibility

  I managed to install all Qosmio X 300 drivers on Windows 7 64 bit. Everything works fine except this one: 'Toshiba Accessibility. When I click on a button of 'Access', I get this error message:

  "This system cannot use Toshiba Accessibility"

  I get this and what is this feature?

  Hello

  I agree with the user above. I think you didn't install Toshiba Value Package added but it is necessary to other tools to operate. You can download it on the Toshiba site so take a look at it again.

  Check this box!

• Galaxy S4, HP 8600, error: cannot use this photo option

  Hello.  I have a problem with mobile printing to my HP 8600 N911g of my Samsung Galaxy S4 v4.2.2 Android running.

  According to the HP documentation this combination of devices should be able to use the built-in HP android printing solution, which basically means that I wouldn't install anything to print.  When I try to print from the browser on the phone, I choose the option 'print '.  I am able to locate and select the printer on my network.  I see the preview of the web page on the phone.  I click on the "print" button and get a message in the top of the screen saying "starts to print.  Then I get an error pop up at the bottom that says: "print error: cannot use this print option.

  I turned the market things.  The phone and the printer are on the same wifi network.  The printer I have installation ePrint as well as wifi direct (although I do not know what counts).  I tried to disable bluetooth.

  Clues?  Would appreciate some help here.

  PS - I also tried to download the HP ePrint app on the android market and had success with either... but I'm sure that I shouldn't do that, right?

  Thank you.

  I got a success...
  I tried to change the printer by 'search' again, then clicked on my printer and then it worked...

• Cannot use audio controls 4000 keyboard wiler (xp home sp3/w) has worked with 3000 keyboard

  Have purches an ergonomic natural 4000 wired keyboard with home sp3 xp3. Cannot use Mute, + & - audio.  All these features have worked under natural ergo keyboard 3000.

  Hello

  Have you tested the keyboard with the keyboard Diagnostics tool in Windows XP?

  Click Start, click run, type mskey in the Open box, and then click OK.

  1. Press multiple keys to verify that the keys match the keys identified in the MS Key window.
  2. When you are finished, click exit.

  This will show us at least for XP to recognize the buttons.

• DeskJet 460, cannot use the Toolbox Windows in Windows 7

  Just bought mobile printer HP Deskjet 460 take traveling with the new laptop, which will no doubt be Windows 8.  Installed printer on my computer running Windows 7.  Installed automatically when I plugged it in.  Do not have installation CD.  Downloaded Windows box to tools on the HP site, but when I try to use it I get message cannot use it because the printer driver is not installed.  Tried the solution I found in this forum to run the Toolbox in compatibility mode for Vista and that caused a window to open it by saying I need to align the cartridges, but the Toolbox then basically hangs and will not function.  How can I perform the functions described in the user guide when they say open the Toolbox?

  The printer prints large so far, but I have a feeling I'll need Toolbox afterwards.

  Is this printer just not completely compatible with Windows 7 or 8?

  Is there another way outside the Toolbox to align the cartridges or clean them or what is in the box at tools?

  Hi @KathyAtHome

  There is no complete software driver for the 460 Deskjet which is compatible with Windows 7 or 8, instead, you use a driver in OS and features.

  With the - OS driver, some of the buttons on the product do not work, and some of the advanced features of these products are not available. For more information about your driver in the OS and see workarounds for lost features, go to the frequently asked questions section.

  You can see, " ", "workaround solutions use following HP Toolbox when you install the product using the driver in Windows 7. "

  

  BUT,

  You can use the print HP and doctor Scan to perform this maintenance like cleaning the print heads and to check ink levels.

  

  

  

  Click here to download and run the print and Scan Doctor > www.hp.com/go/tools

  If you need help, let me know if this resolves the issue, please let me know by marking this message as "accept as a Solution. Thank you.

• Cannot use mouse on Ubuntu hosted on vmware Fusion on a mac

  Hello world

  I'm running into a problem that I can't seem to understand-

  I can't get the mouse running x on Ubuntu hosted on a mac. I keep seeing these errors in the console:

  [85.137467] init: before the start of plymouth-stop status 1 last updated (1769)

  [94.768947] psmouse serio1: vmmouse: impossible to extract the data of State

  [94.769646] psmouse serio1: VMMouse to isa0060/serio1/input0 lost synchronization at byte 3

  [94.786399] psmouse serio1: vmmouse: impossible to extract the data of State

  [94.786895] psmouse serio1: VMMouse to isa0060/serio1/input0 lost synchronization at byte 3

  [94.803792] psmouse serio1: vmmouse: impossible to extract the data of State

  [94.804212] psmouse serio1: VMMouse to isa0060/serio1/input0 lost synchronization at byte 3

  [94.821407] psmouse serio1: vmmouse: impossible to extract the data of State

  [94.821913] psmouse serio1: VMMouse to isa0060/serio1/input0 lost synchronization at byte 3

  [94.838185] psmouse serio1: vmmouse: impossible to extract the data of State

  [94.838593] psmouse serio1: VMMouse to isa0060/serio1/input0 lost synchronization at byte 3

  [94.838594] psmouse serio1: show reconnect request

  and I can't tell if it's a configuration issue with vmware or a configuration problem in Ubuntu (or more likely, both).

  The mouse worked - but when I installed a window manager and improved, it seems to stop working.

  Any suggestions or points on how solve/debugging/troubleshooting this would be greatly appreciated.

  I googled around and installed xserver-synaptic modules and tried different 50 - synaptics.conf file.

  My/proc/bus/input/devices looks like this:

  Bus I: = 0019 Vendor = 0000 product = 0001 Version = 0000

  N: name = "button".

  P: Phys = LNXPWRBN/button/input0

  S: Sysfs = / devices / LNXSYSTM:00 / LNXPWRBN:00/input/input0

  SUP: Uniq =

  H: managers = event0 kbd

  B: PROP = 0

  B: EV = 3

  B: KEY = 10000000000000 0

  I: bus = 0011 Vendor = 0001 product = 0001 Version = ab41

  N: name = "keyboard at translated Set 2.

  P: Phys = isa0060/serio0/input0

  S: Sysfs = / devices/platform/i8042/serio0/entry/entry 1

  SUP: Uniq =

  H: managers = sysrq kbd event1 leds

  B: PROP = 0

  B: EV = 120013

  B: KEY = 402000000 3803078f800d001 feffffdfffefffff fffffffffffffffe

  B: MSC = 10

  B: LED = 7

  Bus I: = 0011 Vendor = 0002 product = 0013 Version = 0006

  N: name = "VirtualPS/2 VMware VMMouse.

  P: Phys = isa0060/serio1/input1

  S: Sysfs = / devices/platform/i8042/serio1/input/4

  SUP: Uniq =

  H: managers = mouse0 event2

  B: PROP = 0

  B: EV = b

  B: KEY = 70000 0 0 0 0

  B: ABS = 3

  Bus I: = 0011 Vendor = 0002 product = 0013 Version = 0006

  N: name = "VirtualPS/2 VMware VMMouse.

  P: Phys = isa0060/serio1/input0

  S: Sysfs = / devices/platform/i8042/serio1/entry/input3

  SUP: Uniq =

  H: managers = mouse1 event3

  B: PROP = 1

  B: EV = 7

  B: KEY = 30000 0 0 0 0

  B: REL = 103

  Bus I: = 0003 vendor = 0e0f product = 0003 Version = 0110

  N: name = "VMware VMware Virtual USB Mouse"

  P: Phys = usb - 0000:02:00.0 - 1/input0

  S: Sysfs=/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1/2-1:1.0/0003:0E0F:0003.0001/input/input5

  SUP: Uniq =

  H: managers = mouse2 event4 js0

  B: PROP = 0

  B: EV = 1f

  B: KEY = ffff0000 0 0 0 0

  B: REL = 140

  B: ABS = 3

  B: MSC = 10

  Bus I: = 0003 vendor = 0e0f product = 0003 Version = 0110

  N: name = "VMware VMware Virtual USB Mouse"

  P: Phys = usb - 0000:02:00.0 - 1/input1

  S: Sysfs=/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1/2-1:1.1/0003:0E0F:0003.0002/input/input6

  SUP: Uniq =

  H: managers = mouse3 event5

  B: PROP = 0

  B: EV = 17

  B: KEY = ffff0000 0 0 0 0

  B: REL = 143

  B: MSC = 10

  I found this thread and it helped: cannot use the mouse in the Ubuntu VM

  However, the solution for me was the opposite. I needed to activate "Auto-detect of mouse for games.