Circuits group with cards VWIC2-1MFT-T1/E1 and VWIC3-1MFT-T1/E1

Similar Questions

• Tried to replace the video card integrated with card pci-e x 16 and lost audio - help please

  Is this normal - when you replace your car video with a pci-e video card you would lose your sound.  The system I have is a Pavilion a1450n and has 3 pci slots and 1 pci-e.  I changed the pci-e video in the bios and everything is fine, but no sound at all.  When I took out the card then I would sound.

  Please help.

  The former system of video seems to give me a little trouble.  He keeps hide and freeze from time to time.  Don't know when that will happen.  But when this happens, a blue screen it freezes or just blanks out and comes back.  It will happen nobody knows.  Everything else works fine.  Hate to give up this old gem - for a lot of software installed to lose.

  Thank you all very much for help.

  William

  Hi, William.

  Yes, when you have an old PC where the BIOS does not have HDMI.

  Your PC thinks that you have installed a sound card and a video card because of the HD audio chip on the video card.

  Thus, he disabled the integrated audio system.

  The fix should be easy...

  Go into the BIOS of your PC, look at the options menu and find the onboard audio setting.

  It will be set to auto or off.

  Change the setting to "Enabled". Save the configuration it and yet when you go out (save the settings and exit).

  When you restart, you should have the back of Board.

• WIC T1-1DSU vs VWIC2-1MFT-T1/E1

  Hi all

  I'm looking at a router of production with a VWIC2-1MFT-T1/E1 module, and none of the two parts of the serial p2p connection configurations of clock rate. Now I know, the VWIC2-1MFT-T1/E1, everything is configured under the controller interface. However I don't see any orders as with the WIC-1DSU clock rate. How does this work? Does this mean that there is a CDU/CSU at this place? I'm just used to seeing the WIC-1DSU-T1 more and have not worked with before multiflex modules.

  Thank you

  Hello

  If you have a WIC-1DSU-T1, WIC-1DSU-T1-V2 or HWIC-1DSU-T1, you pass under the clock interface source configuration and type of service-module t1:

  3845_2 (config) #int serial 0/1/0

  3845_2(Config-if) clock t1 source #-service module?

  clock use internal adapter

  clock to recover the line

  You have 2 options here as you can see. Internal provides synchronization and line gets by synchronizing. In a circuit back to back, it is recommended to configure one end as 'internal', while the other is "online". If your provider is in the middle to provide synchronization for both ends, the configuration of the 'line' is recommended, but it depends on the specifications of the circuit. You can use the "show-service module" (don't forget the counters to see compensation costs statistics) command to see if there are synchronizing issues. Basically, you need to focus on the 'Dry' value, this leaflet. If it increases, it is recommended to check if the synchronization is correctly configured. Sometimes you need to get the vendor involved to confirm the right configuration of synchronization, you should have.

  On the other hand, if you have a VWICX-XMFT-T1/E1 you must enter in the configuration of the controller and choose the right configuration of synchronization. It works essentially the same as in a WIC-1DSU-T1 hardware and similar.

  T1 #controller 3845_1 (config) 0/0/0

  3845_1(config-Controller) source of #clock?

  race free Free Running Clock

  Internal clock

  recovered clock line

  "The keyword which indicates a clock of free-running from the oscillator on the motherboard, which is used only for testing and back-to-back connections".

  http://www.Cisco.com/en/us/docs/iOS/12_2/12_2z/12_2zj/feature/guide/gthwecan.html

  To search for statistical use of the "show controllers t1 X/X/X" command and avoid using any command "loopback" so that it would affect the connection because it is used only for testing purposes. I hope this information helps and do not forget to note the useful messages.

  Kind regards.

• How to group multiple columns at the same level and sum one

  With the following XML data, I want to simulate the following query in the model. Exactly how can I accomplish this?
  
  Thank you
  Kurzweil4
  
  < pre >
  < G_MAIN >
  < LINE_CREATION_DATE > 17 December 09 < / LINE_CREATION_DATE >
  XYZ < ITEM > < / ITEM >
  HHOENT < PLANNER > < / PLANNER >
  < ITEM_TOT_PEND_QTY > 7000 < / ITEM_TOT_PEND_QTY >
  COMPANY ABC < client_name > < / client_name >
  < CATEGORY_SEGMENT1 > UU98 < / CATEGORY_SEGMENT1 >
  < OSTAND_QTY > 1000 < / OSTAND_QTY >
  SHIP_001 < LOCATION > < / LOCATION >
  JJK < SHIP_FROM_ORG > < / SHIP_FROM_ORG >
  < ITEM_TOTAL_OSTAND_QTY > 38000 < / ITEM_TOTAL_OSTAND_QTY >
  < / G_MAIN >
  < G_MAIN >
  < LINE_CREATION_DATE > 17 December 09 < / LINE_CREATION_DATE >
  XYZ < ITEM > < / ITEM >
  HHOENT < PLANNER > < / PLANNER >
  < ITEM_TOT_PEND_QTY > 7000 < / ITEM_TOT_PEND_QTY >
  COMPANY ABC < client_name > < / client_name >
  < CATEGORY_SEGMENT1 > UU98 < / CATEGORY_SEGMENT1 >
  < OSTAND_QTY > 1000 < / OSTAND_QTY >
  SHIP_001 < LOCATION > < / LOCATION >
  JJK < SHIP_FROM_ORG > < / SHIP_FROM_ORG >
  < ITEM_TOTAL_OSTAND_QTY > 38000 < / ITEM_TOTAL_OSTAND_QTY >
  < / G_MAIN >
  < / pre >
  
  < pre >
  SELECT
  LINE_CREATION_DATE,
  AGENDA,
  PLANNER,
  ITEM_TOT_PEND_QTY,
  CLIENT_NAME,
  CATEGORY_SEGMENT1,
  LOCATION,
  SHIP_FROM_ORG,
  ITEM_TOTAL_OSTAND_QTY,
  sum (OSTAND_QTY)
  Of
  table-name
  Group
  LINE_CREATION_DATE,
  AGENDA,
  PLANNER,
  ITEM_TOT_PEND_QTY,
  CLIENT_NAME,
  CATEGORY_SEGMENT1,
  LOCATION,
  SHIP_FROM_ORG,
  ITEM_TOTAL_OSTAND_QTY
  < / pre >

  http://winrichman.blogspot.com/search/label/grouping

  Certainly, we can group any level that you want

  for each group with data semi flattened

  Count and sum based grouping (could be linked to the crosstab)
  How to make a total in my model?
  Where is my Total issue

  It's a group on the Date of creation
  or

  It's a grouping on the POINT

  or

  It's a grouping on the POINT and PLANNER

• UC540 compatibility with card VWIC3?

  Hi all

  We have a customer using a UC540W-BIS-K9. They move from their office and improve their current ranges from 2xBRI to 1xE1 in order to have 30 channels.

  as you all know, the VWIC2-1MFT-T1/E1 = is now EoL/EoS. Will be the new model VWIC3-1MFT-T1/E1 = be completely cared for and compatible with our

  UC540W-BIS-K9? It is running

  Version of the software is a bit old but...

  !!!!!

  Cisco IOS software, software UC500 (UC500-ADVIPSERVICESK9-M), Version 15.1 (2) T4, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2011 by Cisco Systems, Inc.

  Updated Wednesday, July 12, 11 22:01 by prod_rel_team

  ROM: System Bootstrap, Version 12.4 SB (24r), RELEASE SOFTWARE (fc1)

  The availability of KFL-UC-01 is 26 weeks, 4 days, 14 hours, 11 minutes

  System to regain the power ROM

  System restarted at 22:33:37 THIS Thursday, July 12, 2012

  System image file is "flash: uc500-advipservicesk9 - mz.151 - 2.T4.

  !!!!!

  Thanks for your advice.

  Hi Hiromichi,

  As per UC540 platform reference guide, VWIC3-1MFT-T1/E1is not supported. VWIC2-1MFT-T1/E1 is the only supported card.

  http://www.Cisco.com/c/en/us/products/collateral/unified-communications/Unity-Express/C78-557768-00_540_platform_reference_guide_DS_v2a.html

  Rate to the post accordinly.

  Kind regards

  Kevin

• How to get ethernet workstation in the working group with wireless workstations

  All the g ' Day. I just purchased and installed a WAG120n annex a modem router with an Ethernet to port 1 and two wireless network cards. The problem is that I don't see the workgroup on the NETWORK ethernet card, and the two wireless network cards can not see the ethernet NIC however, I can find each NETWORK card using search. One of the network cards wireless can connect and connect to the ethernet NETWORK card, but when even it will appear in the working group - I have not yet tried with the other NIC wireless. How can I configure my router to allow all machines are? If this is of any help, is NETWORK card ethernet Intel Pro 100 V, wireless is Intel 2200 gb and the other NETWORK card wireless is a D-Link DWA 510. Gordon.

  Hi - I'm going to mark it as resolved: I realized that I was looking for something I didn't need. While I have 3 machines with capacities of networking of industrial quality, all I need is a P2P system. I had already activated beside the TCP/IP NetBEUI, simply because it worked wonderfully on my D-Link G604T GenII and NetBEUI is what you really need on a P2P. TCP/IP must remain, then we can access the internet and the router. We can easily map network drives - which has never been a problem - and I was systematically put out of service on each computer network browser Service to eliminate the 8003 errors that continue to occur. You don't need the network browser in a P2P... In any case, the new (financial) year approaches, have a happy! Gordon. Why doesn't the RichText? I activated in my settings!

• My Yahoo cursor has changed to a diamond with a cross in the middle and nothing in the pick - able (?) groups. How can I change back?

  My Yahoo slider went from arrowhead to a diamond with a cross in the middle and nothing in the pick - able (?) groups. How can I change back? 8.1 (latest) Windows and FireFox (latest).

  You're not referring to auto scroll?

  • Tools > Options > advanced > general: navigation: "use autoscrolling".

• Model 23k300xt want J6s79av #ab: HP wireless 802.11 a/b/g/n/ac dual band Mini card with Bluetooth (R) (2 x 2) and WIDI

  HP Wireless 802.11 a/b/g/n/ac dual band Mini card with Bluetooth (R) (2 x 2) and WIDI

  How do we change this computer to use the 2.4 Ghz for the 5.0 Ghz a wavelength. My Microsoft Surface Pro works on why 5.0 can not this computer there is a double prohibition?

  Help!

  So why didn't it connects to your router on the 5.0 GHz band?

  Did you have to do something special for your other 5.0 GHz Wireless N cards to connect to your router?

  Answer to?  N °

  Then explain to me why you can't connect to the 5.0 GHz with the AC map Strip?

  HP has put the designation of expertise because I have solved thousands of questions from members of the forum, not me.

  It's not my problem if you cannot accept the facts of the case.

  Of course, it's a card dual band.

  On the band of 2.4 GHz and AC on the 5.0 GHz band Wireless N Wireless.

  If you want this map to be able to connect to the 5.0 GHz frequency, then you need to upgrade your router to router dual-band wireless AC.

• Conflict of resource with card wifi PCMCIA on the boot process

  -Did you turn off the wlan card integrated in the victory and also with the switch near the wlan on board.
  -Did you flash the latest bios version

  Seems that the problem is loading.

  Is it possible to disable the onboard in the loading process? Even though I'm sure it must be possible to have two cards installed?

  I'm really looking forward to receive assistance.

  A shame that there is no cat.

  No, as much as I know you can disable only the LAN card and not the wireless network card.
  The wireless network card may be disabled in Device Manager.

  But have you tried to change BIOS options for the PCMCIA card.
  I put t know what phone you have but the Toshiba BIOS options of configuration on the second page.
  If the configuration of the device is set on all devices, you will be able to change the PC Card controller mode to: Auto selected, compatible CCIP or CardBus/16-bit

  If he not there no improvement then I guess there is nothing to see

• Photo constantly order of photos in a slideshow changes no matter how many times the movements of the user the photo back to the good look at an order. Example: Bathroom Plans eventually grouped with pictures of kitchen! I have found no way to stop this o

  Apple Photo 1.3 serious problems - how can I SOLVE all these problems?

  (1) breaks down without rhyme or reason no matter where I am in the workflow.

  (2) pictures will not be Shut Down Every Time, even after several days of waiting.

  (3) aPhoto frequently badly chooses picture in the EDIT picture option, I get a picture different than the one I clicked on which is on a 100 pictures in a row.

  (4) picture constantly order of photos in a slideshow changes no matter how many times the movements of the end user the photo back to the good look at an order. Example: Bathroom Plans eventually grouped with pictures of kitchen! I have found no way to stop this weird behavior! Is there a way to stop this? If I drag the photo again some 7 additional photos in the slide show, after a minute or less, he appears again to where it was it not. !@#$%$#

  (5) If you make any CHANGES to a photo, it often changes the appearance of your complete slideshow of this picture with impatience. So you lose all this not work fix your configuration of the slide show. Even changing the order of photos once more that I had put back where they should be. !@#$$#@

  (6) photo identifies often shades of lamps and long door handles as the faces of the people.

  (7) photo made bad decisions when it comes to brightness, contrast and colors effortlessly around other than to use other software, where as with iPhoto there was a lot of workarounds. I could continue, but will save one who might be reading of this.

  I am up to date on all updates for my Mac. If anyone have REAL answers so please spilling the beans, but according to me, it's the only truth is that Apple has rolled out a product inferrer to replace an exceptional product, called iPhoto, which does not work on my new iMac computer 5K of 27 ".   If I knew what I would have chosen another computer that I use iPhoto to prepare more of fifty to sixty thousand photos in a given year and I use iPhoto to make hundreds of slideshows from it.  Are there plugins for Photo 1.3? I ask because I see where there could be Add-ons, but I can't find.

  Apple has taken a serious decision by turning his back to iPhoto and tens of millions of loyal users.

  Thanks in advance to anyone brave enough to tackle this job.

  James

  First, back up your library of Photos and hold down the command and option keys while launching Photos - repair your database - you have a corrupted database

  LN

• Cannot create a smart group with three conditions

  When I create or edit a smart group, I can specify one or two conditions. But if I try to add a third condition, no third line is displayed, even if the OK button goes grey as if a third line were appeared containing a partially specified condition.

  Does anyone of you can create a smart group with three or more diseases? I can't.

  You need to scroll to the bottom of the list of criteria to see one after another. The window is not resized.

• With the help of Lego sensors and motors through the LabVIEW and NI PCI card

  I want to connect a card PCI NI Lego motors and sensors and drive motors and the data of sense using LabView. What card PCI can I use? Thanks for a great site and fantastic community online.

  Hi Tom,

  Looks like a great app.  NXT with LabVIEW Migration will be a big intermediate step before joining more industrial and better sensors with a PCI, PXI, cDAQ or cRIO.  We have a lot of options when it comes to vision and control and acquisition of movement, and we have dedicated forums for all of these products as well.

  Machine vision: http://forums.ni.com/t5/Machine-Vision/bd-p/200

  Motor control and motor control: http://forums.ni.com/t5/Motion-Control-and-Motor-Drives/bd-p/240

  Programming LEGO Mindstorms LabVIEW Guide: http://digital.ni.com/manuals.nsf/websearch/93B7EC451C8DEEC68625762B005380FE

  Getting started with LEGO Mindstorms: http://digital.ni.com/manuals.nsf/websearch/80456522F9BE87FB8625746400540977

  Good luck

• Can I create a distribution group with other than microsoft email accounts?

  I want to be able to communicate with a set of independent consultants and match them with each other as a group. I tried to create a distribution group, but I am not able to add addresses of e-mail for the domain package. Anyway I can do this?

  I thank;

  Ivan.

  Hello

  This thread has been created in the Microsoft answers Site Feedback forum. the Microsoft moderation team has moved this thread on the Forum of Networking, Mail and get online other/unknown .

• Creating security group with grants decided in active directory - Server 2003

  Hello

  I need to create several different security groups for about 7 users with grant different access rights, but all users will access the same folder main and some of the same void records. I created a group with some of the users but appear to have access to all the folders there particular subfolder but I only want to have access to some of the folders in the selected subfolder.

  I guess what I'm asking is how do I create groups of different security with grants decided for each groups and ensuring that users in these groups only have access and subsidies to certain folders.

  I don't know if I explained myself properly but I certainly confused myself, I hope someone can point me in the right direction to solve this problem.

  Thanks in advance

  Jah

  Jah,

  For assistance, please ask for help in the appropriate Microsoft TechNet Windows Server Forum.
  
  Thank you.

• Solitare opens suddenly, with cards staked in a stack to the top left corner. I was not able to detach them to play a game. Help!

  Solitare opens suddenly, with cards staked in a stack to the top left corner.  I was not able to detach them to play a game.  Help!

  Hi Perren7,

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. open an elevated command prompt. To do this, click Start, click programs, accessories principally made, right-click Guest, and then click Run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  2. type the following command and press ENTER:

  sfc/scannow

  3. the sfc/scannow command. analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  If that is not enough then try to create a new user account and check what is happening. To create a new user account

  1. to open user accounts, click the Start button, select Control Panel, click user accounts and parental control, and then click user accounts.

  2. click on manage another account. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. click on create a new account.

  4. type the name you want to assign to the user account, click an account type, and then click on create an account.

  If the new user account works fine then the old account has been corrupted, you can follow the link given below to fix the corrupted user profile.

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.