Cisco ACS 5.3 - How only allow specific ad groups you want to connect

Similar Questions

• How to allow access to all users of the connection on my computer?

  How to allow access to all users of the connection on my computer?

  Your question is hard to understand.  I interpret as:

  "How to allow all the users on my computer to access some files or folders?

  The answer depends somewhat on the question of whether you have XP Pro or XP Home, but a general answer is found the following article.

  "How to use file sharing Simple to share files in Windows XP"
    <>http://support.Microsoft.com/kb/304040 >

  Click on "level 3: files in shared documents available to local users"

  HTH,
  JW

• Unable to set usage, only allowed 1%. When you click OK ' could not ask for the parameters for the reason next 0x8007007b '.

  Windows 7 Home Premium (64-bit) Service Pack one.  Unable to set usage, only allowed 1%. When you click OK or apply. Get error message» Could not apply the settings for the following reason: the syntax of label file name, directory or volume is incorrect (0x8007007b).

  Original title: System Restore

  Hello

  You did changes to the computer, before the show?

  The error 0x8007007B occurs when the system is configured to store the restore on a wrong path or location points

  Follow these steps and check.

  a. click Start, type sysdm.cpl and press enter.

  b. click on the System Protection tab.

  c. automatic restore points, deselect any location invalid or duplicate.

  d. click on check the C: drive with the Windows Logo.

  e. click apply , and then click on Ok.

• "How to stop this message"do you want to install the plugin required to view media on this page.

  How to stop this message "do you want to install the plugin required to view media on this page.

  I don't need the plugin to play the video ok

  If it comes from the Flash plugin you can switch pref plugins.notifyMissingFlash false on the topic: config page.

  You can open the topic: config page via the bar of address and you can accept the warning and click "I'll be careful" to continue.

  • http://KB.mozillazine.org/about:config

• 5.2 ACS command set - how to allow empty arguments?

  Hello together,

  After the passage of a very old ACS ACS 5.2 3.2, I wonder how to specify an argument empty in a set of commands.

  Example:

  I want to allow:

  To write

  but I don't want to allow:

  write terminal

  write erase

  write the network

  write the kernel

  and so on.

  If I specify command = "Write" and leave the field to the empty argument, each argument is allowed. It would also "erase writing" what I don't want.

  ACS 3.2 I could specify command = "Write" and the argument ="^$". It's exactly what I want. Writing command with an empty argument is allowed. If there is no argument, the command is rejected.

  "ACS 5.2 if I get the same string in the field of the argument, the."is filtered and in the config is now only the string" ^ $"does not."

  Someone has an idea, how to specify an argument empty?

  BTW: View ACS shows only [CmdAV = writing] in newspapers...

  Thanks in advance for your help,

  Tobias.

  Please try the workaround in this bug to see if it works or not. The bug has been produced for some time, but it has not yet been set.

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtj62315

• Cisco ACS 5.2: How "service account" exempt from the life of password policy

  We have a GBA policy to disable the user account (user internal store name) after X days if the password is not changed.

  However, it creates challenges 'service accounts' servers NM. My goal is to exclude these password change service accounts. in other words, their passwords must not be updated.

  How to configure ACS to do this?

  THX

  Eric

  Hello

  I don't think it's an option.

  Dan

• How to allow another computer to access my wireless connection

  I'm connectedo to router Wireless 'InfostradaWifi '. Please help to allow me to set up this computer to allow access wifi by any computer nearby. A nearby computer gives the message: "cannot connect to the hidden network"InfostradaWifi". Thanks in advance for your help.

  Isaac

  Hello

  Windows operating system you are using?

  Method 1:

  Configure the computer to start clean, temporarily disable the firewall and Antivirus

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  How to set up Windows 7 to start in a "clean boot" State

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: Wi - Fi and in Windows network connection issues

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  See also:

  Wireless network card: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions

  I hope this helps.

• Cisco ACS 4.2 a user in several local groups

  Currently, I like this group map

  ACS groups window

  GRP of GRP-A-B-1 and PDM - 2
  GRP - A. GRP - 1

  GRP - Grp-2 B

  For example currently a user test1 is part of two groups 1 and 2 under windows and is mapped to the Grp-A-B of the CSA. Is it possible if I delete the mapping of Grp-A-B in ACS and can see the user test1 speratley in both groups (Grp - A and Grp - B) to GBA?

  Salam Muhammad,

  If you have a local user in ACS, this user cannot be a member of both groups at the same time.

  The same concept applies to external users. They cannot be mapped to two different groups at the same time.

  If you delete the configuration of Grp-A-B, the test1 user will be mapped to the first group in the list because ACS 4.2 process mapping group in the order:

  ' the snip "'

  Order of group mapping

  ACS always maps users to a single group of TISA. However, a user can belong to several groups the group mapping. For example, a user named John could be a member of the ensemble of the engineering group and California, and at the same time be a member of the combination of Group Engineering and management. If the value of group ACS mappings exist for these two combinations, ACS must determine what group John should be affected.

  ACS prevents contradictory group set mappings by assigning an order of mapping for the whole group maps. When a user who is authenticated by an external user database is assigned to a group of ACS, ACS begins at the top of the list of groups for this database mappings. ACS sequentially checks group memberships of user in the database of the external user against each group mapping in the list. Where to find the first set group mapping corresponding memberships to external users in the user database, ACS assigns the user to the group this group map ACS and ends the process of mapping.

  ' the snip "'

  Reference:http://goo.gl/cvc474

  HTH

  Amjad

  Rating of useful answers is more useful to say "thank you".

• How can I disable the Do you want to save the password?

  When I open a site like facebook, there is a window that asks if I want to save password and two options, save or not now. How can I disable this window?

  If you disable the Firefox password manager, so you should not get the pop up window to remember passwords.

  Tools > Options > Security: passwords: [] "Remember passwords for sites".

• You want to connect laptop that is only temporarily used wireless to Ethernet connection...

  This seems to be a simple question, but again I received conflicting answers.

  I have a laptop (Toshiba Satellite U305-S5077) running Vista HP SP1.   The office that is connected to my router has developed age problems; He ran Xp2.

  If I want to connect my laptop via Ethernet temporarily for example to change the settings of the router, I have to manually disable my wireless connection, firstly, and then he reactivate manually after disconnecting?

  A source said that Windows does NOT automatically, to ensure stability & connectivity, this should be done.  Another source said no need.

  In short, can I just plug my laptop into the Ethernet without do something else first?

  Your recommendations?

  Thanks in advance for advice and counsel.

  MWQ133

  My recommendation would be to disable the wireless device when you use the wired Ethernet connector. Brian Tillman [MVP-Outlook]

• How to remove the warning "do you want to save the changes to investigation.pdf before closing.

  Question: To remove the warning "do you want to save the changes to investigation.pdf before closing.

  I created a file of pdf XFA (using the LC Designer 8.2) to view this issue

  I can't attach PDF file. Without attaching the pdf file, it would be difficult to explain.

  Click event js:

  function activateUser() {}
  var PDFVersion = xfa.host.variation + xfa.host.version;
  xfa.host.messageBox ("registered button click event");
  XFA. Form.Form1.sendForm.welcomeMsg.Presence = "invisible";
  XFA. Form.Form1.sendForm.successMsg.Presence = "visible";
  Event.Target.Dirty = false;
  };

  docReady event js:

  function displayInfo() {}
  var res =xfa.host.variation;//Added this line to display the successMsg
  xfa.host.messageBox ("docReady event recorded");
  XFA. Form.Form1.sendForm.welcomeMsg.Presence = "visible";
  XFA. Form.Form1.sendForm.successMsg.Presence = "invisible";
  };

  docClose js event:

  xfa.host.messageBox ("docClose recorded event");
  Event.Target.Dirty = false;

  Steps to get the caveat:
  (1) open the attached pdf using Acrobat Professional.
  (Bouton 2) click on registration to confirm.
  (3) now close the document and the Acrobat gives a warning "do you want to save the changes to investigation.pdf before closing.

  The XFA pdf summary:
  It has two text fields. DocReady event field has done this & field B is rendered invisible.
  The button click event of the field made invisisble & field B are made visible.
  Closing the pdf should not raise this warning message.

  My Efforts:
  (1) found a property in js adobe docs.
  Event.Target.Dirty = false;
  It does not solve the problem.
  (2) I tried to put this logic in almost all the events listed in the designer, but I'm not able to solve the problem.

  Please help me solve this problem.

  Hello

  Change the visual appearance is dirty the screen, before all data are actually entered in the form. I've seen this before.

  I think that the docClose event is too late to have the sale/requiresFullSave script. preSave does not either, as this is triggered after the warning dialog is displayed.

  For a test, I would put the sale/requiresFullSave script in the layout event: loan. Not the most efficient, but he should do after changing the visibility of the messages.

  This could be interesting: http://cookbooks.adobe.com/post_How_often_events_fire_and_their_sequence-16547.html

  Niall

• Cisco ACS 4.2: Question about the license...

  Dear Sir

  When I started this project, we start with the demo available on the Download Center on Cisco.

  We have purchase a license and we expect the CD/DVD with the license.

  But... How can I convert the 'demo' to a licensed version?

  Should I reinstall Cisco ACS?

  How the license is supplied, is a registry key? A small file?...?

  Thanks in advance,

  Make a backup of the current configuration, you want to keep it.

  System configuration > backup ACS > backup now.

  Then when you get the full version, just run the setup and it automatically detects the trial version, and invite you, if you want to keep the configuration or not, checks to keep the configuration and move forward. And you'll have improved trial full version.

  There is not the registry keys concerned.

  Kind regards

  Prem

  Please rate if this can help!

• connection via Cisco ACS 5.0 limit

  Hi all

  My infrastrucer wireless a few days ago I deploy Cisco ACS 5.0 with Active directory integration. My wireless users are connecting through web authentication process. The authentication process is gone through AD & his works very well. But I want to work on my 5.0 ACS that a user cannot simultaneously connect several devices at a time.

  Hello Sabine,.

  'max sessions' featre introduced acs 5.3.

  Maximum user sessions

  For optimal performance, you can limit the number of concurrent users to access the network resources. ACS 5.3 imposes limits on the number of simultaneous sessions of service by the user.

  The limits are defined in several different ways. You can set limits to the user level or at the level of the group. Depending on the configurations of the user's maximum session, the session number is applied to the user.

  IMPORTANT: for maximum sessions work for access of the user, the administrator must configure RADIUS account management.

  You can go through the link listed for more information below:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/access_policies.html#wp1176806

  The code that you're using now ACS 5.0 is not recommended for a production environment. You need to upgrade the ACS to achieve the functionality of session max.

  Jatin kone
  -Does the rate of useful messages-

• "Do you want to view only the webpage content that was delivered safely. "the Web page content that willl be sent using a secure HTTPS connection, which could jeopardize the securityof the entire Web page.

  Original title: SECURITY WARNING

  When I try to open a program I have getthis message:

  "Do you want to view only the webpage content that was delivered safely.

  "the Web page content that willl be sent using a secure HTTPS connection, which could jeopardize the securityof the entire Web page.

  Is this something that needs to be corrected?  If yes how.

  Hi billkabay,

  (1) program which you are referring?

  (2) is the problem confined to this specific programme?

  (3) since when are you facing this problem?

  This problem normally occurs when you open Web pages in internet explore. Please specify if this happens when you open a program or opening a Web page or link in internet explore.

  You can see the steps in the link below

  https://community.dynamics.com/product/crm/crmtechnical/b/crminogic/archive/2009/07/09/how-to-disable-the-34-do-you-want-to-view-only-the-webpages-content-that-was-delivered-securely-63-popup-for-custom-pages-added-to-crm.aspx

  Also see the steps by Vincenzo Di Russo (check the post Saturday, May 30, 2009 11:36) in the link below.

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/e7526a5f-F953-4235-90c3-004f9b973585

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I connect my Mac to a network server? As in windows yo go to my computer / connection to a network drive, and then you select a letter and write the name of the server that you want to be logged

  I'm trying to adapt Windows to my new MacBook Pro with OS El Capitan.

  I work remotely for a company and I want to connect my Mac to the server of the company.

  My question is how to connect a MAc to a network drive with the permanently available connection.  For example, in my old HP I went to my computer / connection to a network drive. I've selected a letter and note the name of the server that I wanted to be connected to. The connection was then shown with my other drive hard 'sections '; I want to say C:, D: (for recovery), e: (for tools) and then connecting to the external server has been shown with the selected letter.

  There is no "letter" under OS X. It's a hangover very old of BACK, devices of mapping and volumes labeled mailbox.

  If you are connected to your corporate network, you should see the available network volumes listed in the Finder, in ' my computer > network ", or with the command K to connect to a server.

  You can create an alias for the volume and put it in the Dock, or leave on the desktop or put it somewhere else, and the next time you want to connect to this subject, simply double-click on it. You can also add the server address to your "favourites" in the connect to Server dialog box.