Clone VM and problem with selection of data store

Hello

When I tried to clone a virtual machine that has distributed records in several data stores, I never had the chance to select the store multiple data for the clone, he asks only for the unique data store and discharge all vmkdks to this one, is it possible that I can choose several data stores? for example: I want to drive D: to E: drive to datastoreC c, datastoreB: diving in datasoreA

Thank you

Beatrice

Hi Alain,

When you run the clone operation, when you are prompted to select the destination data store, don't you have an Advanced button? If you click on it, you should have access to a menu where you can choose a different destination for each virtual disk.

Concerning

Franck

Tags: VMware

Similar Questions

Problem with the local data store on ESXi 4.0 U1

Hi all
I have a HP ML330G6 with an internal Smart Array card which is mirrored (R1) SATA two 250 GB drives.
The question I have, is that virtual machines are REALLY slow and inadmissible. I get these errors from the ESXi host when I see problems:
Loss of connectivity to storage device
NAA.600508b10010523953585346555a0100. road
vmhba1:C0:t0:l0 is down. "Touch of data warehouses:"
', 'datastore1', 'Hypervisor1', 'Hypervisor2 ', '.
'Hypervisor3 '.
error
08/12/2009-23:12:28
If I do a constant PING on the virtual machine in question is what it looks like:
192.168.1.4 response: bytes = 32 time = TTL = 128 512ms
192.168.1.4 response: bytes = 32 time = 53ms TTL = 128
192.168.1.4 response: bytes = 32 time = s TTL = 128 168ms
192.168.1.4 response: bytes = 32 time = 25 ms TTL = 128
192.168.1.4 response: bytes = 32 time = 67ms TTL = 128
192.168.1.4 response: bytes = 32 time = 698ms TTL = 128
192.168.1.4 response: bytes = 32 time = 116ms TTL = 128
192.168.1.4 response: bytes = 32 time < 1 ms TTL = 128
192.168.1.4 response: bytes = 32 time = 250 ms TTL = 128
192.168.1.4 response: bytes = 32 time = 641ms TTL = 128
192.168.1.4 response: bytes = 32 time = 979ms TTL = 128
192.168.1.4 response: bytes = 32 time < 1 ms TTL = 128
Request timed out.
Request timed out.
192.168.1.4 response: bytes = 32 time = 2074ms TTL = 128
192.168.1.4 response: bytes = 32 time = 1ms TTL = 128
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.
192.168.1.4 response: bytes = 32 time = 1987ms TTL = 128
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Request timed out.
192.168.1.4 response: bytes = 32 time = 3989ms TTL = 128
192.168.1.4 response: bytes = 32 time = 1ms TTL = 128
Request timed out.
I turned off all virtual machines and rebooted the host with no resolution.
I looked on the VMware download site and I see no download driver for the HP Server or controller of the group.
Any thoughts?
Thank you!

Beyond the update of the firmware, I would check that you have the battery (BBWC) module installed on your controller and cache in write on. The BBWC module is an option and made a significant difference in performance.

Problem with the CLOB data type.
Greetings,

I am facing a problem with the CLOB data type. I know that the CLOB data type is 4 GB (I use Oracle 9i). But in the Pl Sql procedure, I can only store 34305 size for a CLOB variable character data.

This is the test script that I am trying to run.

DECLARE
-Local variables here*.
I have INTEGER;
C_1 CLOB.
BEGIN
FOR Rec IN (SELECT
*
ACCORDING TO THE TABLE)
LOOP
C_1: = c_1 | Rec.Clo_1;
END LOOP;
EXCEPTION
WHILE OTHERS THEN
Dbms_Output.put_line (SQLERRM);
END;

Here variable C_1 range value 34305 good character regardless of type CLOB. Now the above script fails if query my buckle - huge number of return values. It is throwing the exception "error during transfer of files ORA-06502: PL/SQL: digital error or value."

He would be grateful if someone can help me on this.

Thank you.
You are probably better off using DBMS_LOB.append, instead of the concatenation of varchar2 (|).

And... take off your when-other Manager exceptions, please...

Problem with select query that includes a date

I fought with it for about 4 hours - Yes, quite literally... I was never good with stuff to date. I have a brain block.
In any case, here's the situation:
I have an Access database that has a date/time field. There is no time, just a date in the format dd/mm/yyyy.
This table is a list of classes held for three years. I want to do a query that displays only the classes that have completed after January 1st of this year. I don't want to put the 01/01/2010 in the query itself because I want it to work again next year.
It's the current query:
< name cfquery = "classes" datasource = "" #DSN # "dbtype ="ODBC">"
SELECT classesTitles.ClassTitle, classesTitles.ClassDesc, classCatagories.catagoryName, classes.classStart, classes.classEnd, classes.classNotes, owners.fName, owners.lName, classTime.timeSlot, classes.classID, classes.classLimit
FROM classCatagories INNER JOIN (((classes INNER JOIN classesTitles ON classes.classTitle = classesTitles.classTitleID) INNER JOIN classTime WE classes.classTime = classTime.timeID) INNER JOIN owners WE classes.classInstructor = owners.ownerID) ON classCatagories.catagoryID = classesTitles.ClassType
WHERE the classes.classEnd < 01/01 / #DatePart ("yyyy", now())) #.
ORDER BY classes.classStart, classCatagories.catagoryName, classTime.timeSlot, classesTitles.ClassTitle
< / cfquery >
I don't get any results, but I should get a list of each class that has an end date before 1 January of this year - about 200 cases.
When I swap around the place where clause:
< name cfquery = "classes" datasource = "" #DSN # "dbtype ="ODBC">"
SELECT classesTitles.ClassTitle, classesTitles.ClassDesc, classCatagories.catagoryName, classes.classStart, classes.classEnd, classes.classNotes, owners.fName, owners.lName, classTime.timeSlot, classes.classID, classes.classLimit
FROM classCatagories INNER JOIN (((classes INNER JOIN classesTitles ON classes.classTitle = classesTitles.classTitleID) INNER JOIN classTime WE classes.classTime = classTime.timeID) INNER JOIN owners WE classes.classInstructor = owners.ownerID) ON classCatagories.catagoryID = classesTitles.ClassType
WHERE classes.classEnd > 01/01 / #DatePart ("yyyy", now())) #.
ORDER BY classes.classStart, classCatagories.catagoryName, classTime.timeSlot, classesTitles.ClassTitle
< / cfquery >
I get EACH class in the database, and I should get only about 50
The classes are long about 8 weeks, the dates of beginning and end are in the database in the form of date/time fields, so I need to show everything that ends in 2010, regardless of when it began.
I'm sure it's something pressing, but he's avoiding me.
Thank you
Michelle

Your field format date in access is irrelevent to the situation at hand. Use objects appropriate date instead of trying to build an appropriate string. On 1 January of the current year, the createdate() of coldfusion functions and year() now() are your friends. Then, a message from Adam was not clear, use cfqueryparam with the resulting variable.

Problem with "select * from table" for dynamic IN the list

I have a 'for loop' based a query that does not work. The query is supposed to return the name of the table, the data type and the name of the column in the columns poses a number of name filters. The problem I have is when I run the query into a TOAD with:

schema_list value SCOTT, MED and the clause of 'in' as ' to (select * from table (DATAPUMP_UTIL.in_list_varchar2 (:schema_list))))»

The query returns the expected lines.

When I have it in my code as shown below it returns no rows. I don't know what hurts me, but any help would be great! I'm on Oracle 11.1.0.6.0.

PROCEDURE export_schema_ondemand (schema_list VARCHAR2, encrypt_file NUMBER default 0, mask_sensitive_data NUMBER default 0) IS  
    ...
    schema_list_t := my_package.in_list_varchar2(schema_list);
    ... 
    for c1 in
       (
        with ok_to_mask as (
        select 
            owner,
            table_name, 
            column_name
        from   
           all_tab_columns
        where
            owner in (select * from table(schema_list_t))
        minus
        (SELECT 
            c.owner,
            p.table_name,
            cc.column_name
        FROM 
            all_cons_columns cc, 
            all_constraints p,
            all_constraints c
        WHERE 
            c.owner in (select * from table(schema_list_t))
            c.constraint_type = 'R'
            AND p.owner = c.r_owner
            AND p.constraint_name = c.r_constraint_name
            AND cc.owner = c.owner
            AND cc.constraint_name = c.constraint_name
            AND cc.table_name = c.table_name
        UNION ALL
        SELECT 
            c.owner,
            cc.table_name,
            cc.column_name
        FROM 
            all_cons_columns cc,
            all_constraints p,
            all_constraints c
        WHERE
            p.owner in (select * from table(schema_list_t))
            AND p.constraint_type in ('P','U')
            AND c.r_owner = p.owner
            AND c.r_constraint_name = p.constraint_name
            AND c.constraint_type = 'R'
            AND cc.owner = c.owner
            AND cc.constraint_name = c.constraint_name
            AND cc.table_name = c.table_name))
        select 
            atc.table_name as mask_tab, 
            atc.column_name as mask_col, 
            atc.data_type as mask_type
        from   
            all_tab_columns atc,
            ok_to_mask otm
        where
            atc.owner = otm.owner
            and atc.table_name = otm.table_name
            and atc.column_name = otm.column_name
            and atc.owner in (select * from table(schema_list_t))
            and 
            (
            atc.column_name like '%LAST%NAME%'
            or atc.column_name like '%FIRST%NAME%'
            or atc.column_name like '%NAME_LAST%'
            or  atc.column_name like '%NAME_FIRST%'
            or  atc.column_name like '%ENAME%'
            or atc.column_name like '%SSN%'
            or atc.column_name like '%DOB%'
            or atc.column_name like '%BIRTH%'
            )
            and atc.column_name not like '%PHYSICIAN_%'
            and atc.column_name not like '%DR_%'
            and atc.column_name not like '%PROVIDER_%'
            and atc.column_name not like 'PRESCRIBER_%'     
       )
      loop
         ...

FUNCTION in_list_varchar2 (p_in_list  IN  VARCHAR2)  RETURN VARCHAR2_TT is

    l_tab   VARCHAR2_TT := VARCHAR2_TT();
    l_text  VARCHAR2(32767) := p_in_list || ',';
    l_idx   NUMBER;
        
BEGIN
    LOOP l_idx := INSTR(l_text, ',');
        EXIT WHEN NVL(l_idx, 0) = 0;
        l_tab.extend;
        l_tab(l_tab.last) := TRIM(SUBSTR(l_text, 1, l_idx - 1));
        l_text := SUBSTR(l_text, l_idx + 1);
    END LOOP;

    RETURN l_tab;
        
END in_list_varchar2;

Published by: BluShadow on June 29, 2011 16:11
addition of {noformat}

{noformat} tags.  PLEASE READ {message:id=9360002} TO LEARN TO DO THIS YOURSELF.

Hello

If you have a query that works well when you launch it directly, and that breaks down when you start with a procedure, this can be a problem of privileges.

Points of view ALL_ * shows only the objects you have access, but using a procedure, privileges must be granted directly to the user and not with a role.

You should check the SELECT privileges to your user through roles and give them directly to the user.

Hope this will help.

Sylvie

Design pattern using queues and notifiers and problem with sync

Hello

I'm rearchitecturing a 4-channel data acquisition system which includes data acquisition, indexing of data between four channels, signal processing and recording of data.

All processes are placed in a single loop, and I have subdivided by the following in a producer and consumer two loop (or master with both loops slave), use a queue to manage orders and send the actual data through a notification list. I'm new to this, so I don't know how to go for rearhitecturing but am trying to move several loops. Instead of placing each channel in its own loop, I used only 2 to save duty all architecture. The acquired data are also indexed in the two loops (loop1, loop2):

Main loop: data acquisition (DAQ Assistant) where Notifier sends data to consumers loops, queue for General commands

Loop1: bed (table 2D index), addresses and records the data for channels 1 and 2

Loop2: bed (table 2D index), addresses and records the data for channels 3 and 4

Question 1: Is it ok to use Notifier and queue in the artchiture (best practices)? I would use two queues, but I find that the program may have a lag (although it lacks all data) and who interrupts the acquisition for the user and I don't want that. I prefer the program to retrieve data in real time and then decided to use the authors of notifications to send data to loops1 & 2. What are the caveats of this? Given that I am gaining at the rate of 1 s/s, maybe it will be enough.

With respect to the orders queue, this is done and two commands are queued in order to activate loops1 & 2. Using multiple loops slave/consumer, how we manage several channels? the user can choose to acquire all the channels simultaneously or one at a time. I am able to activate the four channels. In this case, because loops can not run in order, how do you ensure that the item is read by the right loop?

I'm running into a few problems:
Question 2: synchronizing data - use 'wait on ms' synchronize all loops (main loop and loop1, loop2)
-data doesn't seem to be very good sync - why is - this? consumer of treatment<>
-what I'm missing?
Question 3: processing loss data - because using filers is frozen and using queues is not, I did so that orders of the so-called 'turn on' the two loops is done using a queue. I compared it with the notifiers
Question 4: Errors - I made loops 1 & 2 output on the notifier error error - they throw an error when the program stops so happy so I was testing for. I read some ni.forums he's talking about is enough, but what are the other types of error monitoring (error reporting)? Thank you very much for reading!

I programmed so far and it can read all or individual channels but I want check against all cases, that's why I ask these questions to check. I know that architecture may not be the best, so any suggestions would be welcome. I try to get the synchronization of the time and I don't want any data with loss. I guess that the use of queues to send data and commands is ok?

Thank you in advance for your help!

Problems with registration of data in a FPGA project.

I have problems trying to save data that I receive on my CompactRIO. I can get the data off of it, trace and display, but I can't seem to save to a file with a recording of VI. Try to solve this problem, I did a VI outside our project that runs the simple task of saving a table provided in a .csv file. Outside the project, this works fine, but when I add this VI project is when I get problems. If I provide a path outside the project, he invites me to the path, in the project, this guest never appears, but I get an error indicating that the user has canceled the operation. I found that this error is the same as you would get if you closed the guest to use the X rather than hitting the Cancel button. If I provide a path in VI, I get no error, but nothing happens and nothing is recorded. Another interesting thing happens when I move this file to the project. When I go to run it, I get a prompt asking you to save Message String.vi Format because it has unsaved changes, and when I ask him to list the unsaved changes, he said that the VI has been recompiled. When I take the VI on the project and run it, it says he has recompiled again and must still be saved. It's really frustrating when such a simple task will not work for any help that you could give is appreciated.

Will be

He will never be able to save the file on your PC, only on the controller it self.

Then use FTP to transfer the files to your PC.

Or you could do a host PC VI that gets the data from the controller, and then stores the data on the PC.

To transfer the data, you can use TCP or shared variables.

problem with the backup data in text file

Hello

The problem I am facing wihile, saving the data in the text file is that everytime when I'm slecting the path of the façade, data that are recorded are added with the previous data, not only in the new text, the new data set is saved but also, is there any previuos run for the program , the corresponding data is also present in this text file.

However, when I change the same ''(file path) to 'constant' in the control block diagram, and then add the path of the file, it doesn't have this problem. Basically, changing the "file path" constant in the diagram of control block (so that it is displayed in the front panel) is at the origin of the problem.

Help, please!

Thank you

Your shift on the loop Register For is not initialized. It will keep the value of the string since the last time that he performed. That initialize and it should solve your problem.

Problem with registration of data in the txt file

Hello

I have 2009 Labview, Labview real-time 2009 and cRIO 3.3.0. I also NEITHER cRIO-9024 more cRIO-9112 chassis and modules.

I would like to save the data measured modules in the txt files, but I want to do in a period of time to time desire. For example, I want to save data of measurements of 60 seconds and repeat every one hour. I of the project (in the file attachment vi) and normally it works fine but I noticed that the recording of the data is not correct. I mean it seams to save what was in the memory before. That's the problem with Windows XP I have check with another computer with Vista and it seems to be ok. It seems that on XP the buffer (refnum?) is not clear and it retains the previous values.

Can someone explain to me why it happened and how I can obey Windows XP? Or maybe there are techniques to clear the memory buffer/refnum for rescue?

Thanks for any help.

Kind regards

Kamil

Disabled the HTTPS option in Hotmail and problems with the Windows Firewall, Microsoft Security Essentials and Windows updates.

Original title: Windows Live Hotmail only opens a new window links e-mail composition!

I recently put my Windows Live Hotmail account to my default e-mail client in Internet Explorer 8 on my Windows XP SP3 System. Unfortunately, whenever I click on a link to e-mail on a Web page to open a new message, Hotmail tells me, "Sorry, there seems to be a problem with Hotmail right now", and a new/compose message window does not open. I disabled the HTTPS option in Hotmail, which fixed the problem. However, when I went to do a manual update of Windows, I am nailed with a Trojan horse! Apparently, the Windows Firewall and Microsoft Security Essentials have been affected by turning off HTTPS in Hotmail! It's 2012, and it's terribly disappointing that Microsoft only has not ironed out all the imperfections in these services now. If anyone can give me a solution (in simple terms), I would appreciate it!

Thank you

Ryan

Hi Ryan,

1. you receive messages or error codes when you access Windows updates?

2. what happens exactly with the Windows Firewall and Microsoft Security Essentials?

About the update of Windows, the Windows Firewall and Microsoft Security Essentials issues, you may try to launch the FixIt and see if it helps:

Method 1:

Resolve security issues to protect and secure Windows automatically

The problem with Microsoft Windows Update is not working

Method 2:

You can also refer to article and perform a full scan on your computer by using the Microsoft Safety Scanner.

Microsoft safety scanner

Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

On the Windows Live Hotmail account, you can publish your request in instances of Windows Live to get help:

http://answers.Microsoft.com/en-us/windowslive

"Delayed write failed" message keeps appearing to external hard drive (WD passport) and problems with suggest fix kb908673 (register edit).

I had problems with my WD usb hard drive, where a "delayed write failed" message keeps appearing when the transfer of files to or from it. Among the fixes suggested on the WD support site is a link to kb908673, and this seems to sum up my problem. This fix is included in sp3, I believe, however, the fix indicates that a manual registry editing needs to be done;

"After you install this hotfix, the following registry subkey is automatically added and configured:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\USB\EnSoftRetry

The registry key is configured with a DWORD value of 1. This value allows the Soft-Retry code path that is used in this hotfix.

"If you install a later version of the patch (a patch that contains later versions of Usbport.sys and Usbehci.sys), including Windows XP SP3, this registry value not be automatically added and configured. The registry value must be manually added and configured as described above to activate the Soft-Retry code path that is provided in this hotfix. »

I don't have this registry subkey and have no idea how to do to configure a key to have a DWORD value - I can create as a registry entry DWORD value in this key, but it must be given a name. Should I create a DWORD value called "EnSoftRetry" in the USB, or should I create a DWORD value in the EnSoftRetry key and, if so, what should it be called? Or am I completely misunderstanding something here?

(1) manage devices

(2) find each host EHCI USB controller

3) click on USB EHCI host controller Details of the

Highlight 4) Device Instance path

(5) copy "Device Instance path«path information in the Notepad for quick and easy access»»

(6) open Regedit

7) click "HKEY_LOCAL_MACHINE."

8) click on 'SYSTEM '.

9) click on CurrentControlSet «»

10) click on 'Enum '.

11) click on "PCI".

(12) click on ' * the folder that corresponds to the stage 4 information.

(13) this is where you should be now: "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\PCI\------\Device Parameters.

(14) right click on 'device settings '.

(15) select "new-> Key".

16) enter the field of naming the new key 'EnHcSoftRetry '.

(17) right-click on "EnHcSoftRetry"the ket has created "

(18) select "new-> DWORD (32-bit value).

19) enter the field of naming 'DWORD '.

(20) right click 'DWORD '.

(21) select 'change '.

(22) entry in the field value '1' Base of Hex

(23) close regedit complete process :)

BlackBerry Q5 big problem with BB Q5 data - IP ADDRESS REJECTED. :( :(

Hi all!! I have a blackberry Q5, the version of the 10.2.1.2102 software... It is the best blackberry smartphone I've ever had! but since one week, I have a very big problem with my BB Q5: if I want to surf the internet, with data from my phone (not in WIFI mode but with the data of the phone (4G, 3 g +)), I can not go on any website, but the only thing I watch is a white screen with this message "ERROR HTTP 403.6 ": the IP address of the client has been rejected"...! What can I do? I'm really desperate! I called my provider (SFR), they told me that my connection is ok, I'm not a problem with them, and this is my phone... HELP ME PLEASE!

Hello!!! Just to say that finally, after several attempts, I have solved my problem: there was a problem with my service provider SFR with my phone! I regret bringing this up on the forum, but when you call the customer service you think they know their work... but fortunately for us if we have the blackberry is because we are not so ignorant on the connections, network and telephone line! : D have a nice day blackberry users!

Problem with sharing of data specific to the application via BBM 10.2

Hello - I am having a problem of data sharing applications with BBM 10.2-specific. I take the advice of some comments here, and it seems to work on 10.1. I can receive the file on 10.2, but when I try to share on the same device that I get this:
```
InvocationWrapper::onQueryFinished: no matching result from Menu Service for query
   mimeType=""
   uri=QUrl("file:///accounts/1000/shared/misc/My App Data.myapp")
   data= ""
   metadata= QMap()
   perimeter= 0
   action= "bb.action.SHARE"
   target= "sys.bbm.sharehandler"
   invokerIncluded= false
InvocationPrivate::onQueryResolved: no result matching query, no armed signal sent.
```
It is the call that I use, which works on 10.1 but not 10.2:
```
Invocation {
   id: invokeBBM
   query {
      InvokeQuery {
         id: invokeBBMQuery
         uri: "file:///accounts/1000/shared/misc/My App Data.myapp"
         invokeTargetId: "sys.bbm.sharehandler"
         invokeActionId: "bb.action.SHARE"
      }
   }
}
```
I also tried it with a "text/plain" MIME type and a few other variations, same result. If something has changed in point 10.2?

(And while I'm asking, any reason why I can't use the data instead of a file uri? I need to convert the data in JSON, save the file, share the file, send, receive, save the file on the receiver, then open it, read it, and convert it back. Seems a little roundabout, if I could share the JSON data. "(And this is the only reason that my application requires permissions of shared files)."

Thank you!

It is a problem with the current version of BlackBerry Dev 10.2 Alpha. You can call C++ BBM, but citing QML does not work.

HP Photosmart 6520 and problems with the air IPAD using IOS 8.0.2

Used APPLE IOS 7. No problem with printing to the 6520. Now, I've updated to version 8.0.2. now, to get a message on the IPAD, saying: 'no printer not found '. No printing from laptop to printer and no problem shows on laptop as the printer selected in the folder devices and printers. Y at - it an update of software of HP to run version 8.0.2. .

JERENDS, thanks for your response. I had already tried the "hard restart" at the suggestion of the Apple Tech Help, but that doesn't seem to help. But late last night after posting my question Imtried print again and IPAD are my printer without problem. Why he couldn't find yesterday morning but has been able to find it later in the day is one of the mysteries of life, I guess.

Problem with order submit data record for Reporting ATG

Hi, r. j. Nunes
I am facing problems with the connection to present newspapers for ATG of the report. The logs for RegistrationFileLogger, SiteVisitFileLogger, UserFileLogger, SegmentFileLogger were successfully getting generated but unable to see the logs for OrderFileLogger during shipment of the order.
I understand that the/atg/reporting/datacollection/trade/SubmitOrderEventListener of the listener must be notified so that the listeners of corresponding data is called in the order:
SubmitOrderEventListener-> OrderLogEntryQueueSink-> OrderLogEntryGenerator-> OrderFileLogger
and newspapers would be written.
But I'm not able to determine which component notifies the SubmitOrderEventListener by submitting an order.

Is - this SendFulfillmentMessage component? But SendFulfillmentMessage sends the message to the localdms topic: / local/realization/LocalSubmitOrder on the port of OrderSubmitPort which as component SubmitOrderEventListener listen the subject localdms: / local/realization/LocalSubmitOrder on the DEFAULT port?

Could someone please clarify.
Thank you
Saud

Hello

Pipelinelink = "sendFulfillmentMessage" name has been commented to our commercepipeline.xml that we did not use OOTB Presse. Once I removed the comment, sent messages and newspapers to submit order got generated.

Thank you

Saud

Clone VM and problem with selection of data store

Similar Questions

Maybe you are looking for