Comments to suspend and hibernate results in the cable host is disconnected.

Similar Questions

• How to use vGPU and vSGA both on the same host vSphere 6.0

  I tested vGPU on a host vSphere 6.0 to 6.1 of the Horizon, and I would now add a vSGA pool to this host. Only two physical GPU is used with the two vGPU vm that I turned on.

  My question is, what should I do to make this Host allow compatible vSGA VM turning on and share resources on the other two other GPU?  I put the office pool to use the 'Material' 3D rendering engine and added a VM pool.

  When I try to turn on the virtual machine, I get this error message in vSphere client Web:

  "GPU hardware is required but not available. The virtual machine will not start until the GPU resources are available or the virtual machine is configured to allow software rendering. »

  It's the output of command line gpuvm and nvidia-smi:

  

  The host ESXi 6.0 has two cards of K2 of GRID for a total of 4 GPUS. Only two vGPU-enabled vm is turned on, it seems that I can use the other two GPU for vSGA VM, right?

  It is currently not possible since the Nvidia VIB:s vSGA and vGPU cannot be loaded at the same time.

  The driver will claim all compatible GPU:s (except those configured for passthrough, IE vDGA)

  An exception to this rule is if you have an AMD GPU for vSGA and a Nvidia GPU for vGPU.

  Can't comment on if, and when this will be resolved, perhaps krd can do.

  Linjo

• PIX - static and port redirection to the same host

  Version 6.2 of the PIX

  I was watching the following config:

  static (inside, outside) 172.18.124.99 tcp telnet 10.1.1.6 telnet netmask 255.255.255.255 0 0

  static (inside, outside) 172.18.124.99 tcp ftp 10.1.1.3 ftp netmask 255.255.255.255 0 0

  static (inside, outside) 172.18.124.208 tcp telnet 10.1.1.4 telnet netmask 255.255.255.255 0 0

  public static tcp (indoor, outdoor) interface 10.1.1.5 telnet telnet netmask 255.255.255.255 0 0

  public static tcp (indoor, outdoor) interface 10.1.1.5 www www netmask 255.255.255.255 0 0

  static (inside, outside) tcp 172.18.124.208 www 8080 10.1.1.7 netmask 255.255.255.255 0 0

  go to this URL,

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_tech_note09186a0080094aad.shtml#topic11

  and I was wondering if the following configuration will work or not:

  static (Inside, Outside) 172.18.124.10 TCP 10.1.1.10 netmask 255.255.255.255 0 0

  static (Inside, Outside) 172.18.124.10 TCP 10.1.1.10 netmask 255.255.255.255 0 0

  Thanks in advance for any input.

  Ariel

  Yes, it'll be OK. What you can't have is the following:

  static (Inside, Outside) 172.18.124.10 TCP 10.1.1.10 netmask 255.255.255.255 0 0

  static (Inside, Outside) 172.18.124.10 TCP 10.1.1.10 netmask 255.255.255.255 0 0

  and you can't have:

  static (Inside, Outside) 172.18.124.10 TCP 10.1.1.10 netmask 255.255.255.255 0 0

  static (Inside, Outside) 172.18.124.10 TCP 10.1.1.10 netmask 255.255.255.255 0 0

  In other words, you cannot map the port itself to two different ports, in both directions. The PIX will get confused when it receives a packet on the duplicate port and does not know what a host to map to. As everything inside and outside ports map to unique ports on the other interface then you're OK.

• VShield service Manager installation and vShield app to the same host ESXi

  Hello, I'm planning on vCloud Director assessment in a laboratory with only a single ESXi host.  When I try to install the app vShield service I get the following warning: do not install on a host or a cluster where the VC or the vShield Manager resides. This can cause network problems. The following IP address must be a unique IP address assigned to this unit of App vShield. Please do not use an IP address that is assigned to another machine, including the VC, vShield Manager or any ESX host. Using an incorrect IP address you will need to uninstall and reinstall App vShield on this host. My question is: is it is absolutely impossible to install vShield manager on the same host ESXi as the vShield Manager resides?  Or is it just a bad practice?  What are the ramifications of installing?

  It is a general practice to separate management and resources. What you see is just a warning. When there are very fewer resources available you can do. Make sure that you exclude from the required VM by referring to this post

  http://www.yellow-bricks.com/2012/03/17/excluding-your-vCenter-server-from-VShield-app-protection/

• Method for patching only host ESXi4.1 and VC is on the same host

  Hello people,

  I'm patching one of the ESXi, 4.1.0 348481 and Vcenter Server 4.1 Update1 (VM) is sitting on the same host ESXi. Please let me know how I can this patch

  a single host as the Vcenter also will restart. I'm looking to patch manually rather than Update Manager. How patch manually the ESXi host as there is no rounds in ESXi and what serves the Cli. If his VCLI then what is the command for the application of patches and download link. I'm looking to get the procedure. Any help on this

  will be well appreciated.

  Thank you

  vmguy

  If you have another host, you can vMotion your VM vCenter to it, then use AUVS to patch.  If a stand-alone host, then you will need to turn off vCenter and all the guests and try the method below

  http://communities.VMware.com/people/vmroyale/blog/2010/12/27/single-use-vihostupdate-how-to-for-ESXi-4x

• The s/w and h/w on the same host iSCSI initiators.

  Hello

  Can someone tell me if both software and hardware on the same host iSCSI initiators and looking the same LUN is supported in ESX3.5U5, 4.0U2 and 4.1.

  If this isn't the case, please give me the URL of any article of vmware goes in the same.

  Thank you

  P Martin

  The closest would be on page 28 of the 4.1 "iSCSI SAN slot Guide.

  http://www.VMware.com/PDF/vSphere4/R41/vsp_41_iscsi_san_cfg.PDF

  Because the software initiator ESX is definitely a charge adapter, this could be considered to be applicable.

  In spite of being is not clearly established, there is no summer tested enough to be considered as support even if there are no known issues.

  Andy

• How to display /etc/resolv.conf and other files from the remote host to the vMA host ESX4i

  Hi all;

  I'm new at VMAs, I put it in place and adds 5 Server esxi 4 and I can list the fines using vifp lists broadcast and works, very well but my problem is I want to interrogate the remote servers for this vMA host for example I need to check the contents of these files

  cat /etc/resolv.conf

  cat/etc/sysconfig/clock

  tail/var/log/vmkernel

  Discovered the following

  esxcfg-firewall - q and esxcfg-vswif - l

  Can someone please help me on how to run these commands or another way on how to get this information above hosts and ESXi 4. I checked the forum, but I don't see anything similair nature! now, either I'm stupid full because it's as simple as drinking water and so no one asked or I am just lucky to ask the right question, so be it, I appreciate your time and effort

  Thanks in advance

  Esxlinux

  So its worth your time through the vMA documentation to understand how to manage your hosts and it's main use case. The operations that you are trying to accomplish cannot be done using vMA... at least in the way that you are hoping for.

  See my vMA article and some of the getting started guides.

  cat /etc/resolv.conf

  You will want to use esxcfg-dns to list the configured DNS servers

  cat/etc/sysconfig/clock

  This file does not yet exist on ESXi, if you try to set the time on ESXi host, you should use NTP and it is also important to note that single ESXi uses UTC and no other options are available.

  tail/var/log/vmkernel

  If you need to display the host logs, consider using vi logger on vMA OR configure syslog on your host to send to the centralized syslog server

  Regarding the last two commands, they do not apply to an ESXi host and therefore these commands are not available.

  There are certainly differences between ESX and ESXi, understand the differences and orders to ask for certain pieces of information is very important. vMA can help with this, but you must understand the use case of vMA and what tools are at your disposal. The best way to start is to take a look at the documentation, to jump it and try to jump in, will just be confusing.

  Good luck

  =========================================================================

  William Lam

  VMware vExpert 2009,2010

  VMware scripts and resources at: http://www.virtuallyghetto.com/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".

• Unable to connect to the internet (using a wired connection or wireless) after a power failure, error "the cable network is disconnected"

  After a power outage, I can not connect wireless (cannot connect even with the wired ethernet cable); get message "network cable is unplugged", which is not.  The cable modem work properly in wireless mode with two other computers.  System to an earlier date of reload and change the cable has not solved the problem.  Running Windows XP.  Any suggestions?

  Hello

  I suggest to follow the steps provided and check if it helps.

  How to troubleshoot the following message appears in Windows XP: "a network cable is unplugged": http://support.microsoft.com/kb/910389

  Hope this information is useful.

• I made a form with bootstrap with an email, comments (textarea) field and a shipment or the Send button

  Now how can I send it to my email address?

  Probably with a php file or how.

  I can't find anything in dreamweaver.

  Try this tutorial into 3 parts:

  ALT-Web Design & Publishing: sensitive Contact form with 3.2 Bootstrap and PHP (part 1)

• How to transfer and share files using the cable ethernet on hp probook 4540

  Please using the ethernet cable I connect two laptops with windows OS 8, but can not set up to share files and folders. Please help me, it keeps bombarding me with animals of the AUTHORIZATION.

  Hello Abekah,

  I understand that you need assistance, sharing of files between computers.

  Here is a link to a video that will guide you through the steps.

  I would like to know how everything goes.

• connect and read data from the windows host's Web site

  Hello, I have a Web site hosted by windows server with SQL server, I want to create an application to read all about me and write in the listview. When tcoh each title in the listview opens a new .qml window or call to view or order specific goodbye data thereon in the mode list. like .aspx

  you would need a server component that uses the data, for example a web service soap or json.

• Stop and restart prevented by the task host window

  Hello world.

  I'm having currently a problem each time I try to shut down or restart my laptop. I have the following message:

  «Closing 1 app and restart»
  Task host window
  Task host stops background tasks.

  Windows cannot close it, and I'm finally started on the desktop, but with all my applications closed and even some features of pilot missing (for example multitouch). I can't use the Task Manager as it crashes whenever I open it. By clicking on "restart still" does not resolve the issue and I think that causes a crash (cannot be 100% sure, only tried once).

  Does anyone have any suggestions? I am pleased to provide you with more information if necessary.

  Hello

  Try this, it worked for me.

  1:

  Run the Troubleshooter:

  Follow the steps below:

  (a) press Windows + W together.
  (b) writing Troubleshooting in the search to the corner box and press on enter.
  (c) click the Troubleshooting tab.
  (d) click view all in the upper left corner.
  (e) select the power options in the list.
  (f) click Next to launch the troubleshooter of power.

  Go to the next method if the problem persists.

  Ref: http://answers.microsoft.com/en-us/windows/forum/windows_8-performance/problems-with-windows-8-not-doing-what-it-is/9ad39bdf-ad5a-435d-a393-3b27507da5a4

  2:

  Put the computer to boot and search for the issue.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts. Here is the link for your reference perform the clean boot.

  http://support.Microsoft.com/kb/929135

  Note: Reset to start the computer to a normal startup.

  Browse the event viewer for the cause of code and the exact error number:

  Press the Windows key + X and click on event viewer and follow him.

  Event Viewer is a tool that displays detailed information about the events important (for example, programs that don't start as expected or updates are downloaded automatically) on your computer. The event viewer can be useful when troubleshooting problems and errors with Windows and other programs.

• I look at apple tv in illinois, with service from comcast.  but, I'm moving to arizona for 3 months and cox communications is the cable operator. I always look at my apple tv?

  I look at apple tv in illinois with comcast as my ISP.  I'll be in arizona for three months.  Arizona cable provider is cox communications.  is it possible that I can watch apple tv on a big screen tv?

  As long as you have Wifi/ethernet your OK. Regardless of the name of the current provider.

• Satellite Pro S500 - 11 c is suspended and the fan runs at full

  Hi people,

  I am experiancing a problem with my Satellite Pro S500 - 11 c where close unexpectedly, it crashes and the fan runs at full speed. Discount to zero is my only option and this resulted in the windows having to retrieve a few times so I'm fearing one requiring a major reconstruction after a deadlock of the future. Until now this issue has occurred only when you use a wireless USB mobile of 3G or internet teathering via USB with my iphone 3G. Using another USB port did not help.

  If someone has encountered this problem and have a fix? No help from Toshiba?

  Best regards

  Andrew

  Hmmmm... What to say. Problem is that you use third party hardware and software and some conflicts are possible. The question is: who can help you with this?
  In general you should talk to your ISP provider at first to see what they will say about all this.

  Have you ever talked with them?

• Understand the memory host memory and comments tab

  Hello everyone!

  In the computer virtual host memory resource assignment tab and the host cpu resources consumed in the physical machine (esxi host) and the memory of comments is close to the resources consumed to the virtual machines guests, correct?
  
  Thank you

  Sena.

  SENA,

  The memory of the host is the amount of memory host the VM uses against what has been allocated to it (including overhead).

  The way I understand it, the area of memory comments shows how memory is allocated to the guest - host memory, swap, share, etc..

  Check out this yellow post - Bricks.com for many more details on the parameters of memory in vCenter http://www.yellow-bricks.com/2010/12/20/vcenter-and-memory-metrics/

  Hope this helps,

  Hersey

  VCAP4-DCA

  http://www.vhersey.com/