Communication between the device IDS and router test

Similar Questions

• VPN tunnel between the concentrator 3005 and router Cisco 827

  I am trying to establish a VPN tunnel between the Central Office with VPN 3005 and controller branch Cisco 827 router.

  There is a router of perimeter with access set up in front of the 3005 list.

  I quote the ACLs on the Central perimeter router instructionsuivante to allow traffic to permit ip 3005 - acl 101 all 193.188.X.X (address of the hub)

  I get the following message appears when I try to ping a local host in the Central site.

  Can Anyoune give me the correct steps to 827 and 3005.

  Thank you

  CCNP Ansar.

  ------------------------------------------------------------------------------------------------------

  Debug crypto ISAKMP

  encryption of debugging engine

  Debug crypto his

  debug output

  ------------------

  1d20h: IPSEC (sa_request):,.

  (Eng. msg key.) Local OUTGOING = 172.22.113.41, distance = 193.188.108.165.

  local_proxy = 202.71.244.160/255.255.255.240/0/0 (type = 4),

  remote_proxy = 128.128.1.78/255.255.255.255/0/0 (type = 1),

  Protocol = ESP, transform = esp - esp-md5-hmac.

  lifedur = 3600 s and KB 4608000,

  SPI = 0x83B8AC1B (2209917979), id_conn = 0, keysize = 0, flags = 0x400D

  1d20h: ISAKMP: ke received message (1/1)

  1d20h: ISAKMP: 500 local port, remote port 500

  1d20h: ISAKMP (0:1): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM

  Former State = new State IKE_READY = IKE_I_MM1

  1d20h: ISAKMP (0:1): early changes of Main Mode

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: IPSEC (key_engine): request timer shot: count = 1,.

  You must also allow the esp Protocol in your ACL.

  access-list 101 permit esp any host x.x.x.x (address of the hub)

  Hope this helps,

  -Nairi

• Communication between the page background and the foreground page

  So I understand if you have the following:

  This means that when the unit starts, listener.html will be executed (in the sense that there is no UI element, just javascripts).

  Is - this here anyway for the listener.html file send all information to index.html when it starts? How the javascript code would work in this case (for example if you declare global variables in listener.html, index.html sees it)?

  If you had the two entry points to the same page (so background src = "index.html" as well), which would change anything?

  The use case can be if the listener.html had a setInterval function runs every so often to calculate things, and then the application would be able to use this information.

  I have to have just the page of listener.html send the information to a server, and then retrieve it via a server call the homepage?

  Thank you.

  What if you had both entry points to the same page (so background src="index.html" as well), would that change anything?
  

  This would do the trick. This means that your page is already starting to load at startup, so if you placed your algorithms on your page 'onload' event, it should work.

  And the payment of a bonus, I also used this tip to load my scripts (in particular the JQuery that takes a while to load) so that when the user opens your application after startup, you'd be on your home page.

  Hope this helps

• No communication between the Bluetooth SD - BT2 and PocketPC SD card

  I use an SD - BT2 (PA3271U) card in a Microsoft Pocket PC (also referred to as 'Microsoft PocketPC 2003') 4.20.00. I use the latest driver Toshiba 5.01 C and the card is recognized by the Pocket PC (Medion MD 95450 / MDPPC 150). I can connect to my mobile phone and GPRS connection is accumulation with no problems.

  But later at this point in time, the connection is established but dead... no connection to anyone. It seems that the communication between the Pocket PC and the card SD - BT2 is broken on the software side.

  Anyone have an idea (or a working driver) for this problem?

  Thanks in advance

  Karl

  Hello

  Have you tried to reinstall the drivers or software for SD - BT2?
  In my opinion, you should check this option.
  Also, I found a brand new version for PDA Bluetooth Stack (Bluetooth software and drivers).
  Check out this site.
  http://APS.toshiba-tro.de/Bluetooth/pages/download.php.

  Good bye

• No communication between the printer and the Red computer on switch flashing printer does on every time I turn it off

  I get a message there is no communication between the printer and the computer. Printer is all-in-one HP Officejet 4315v. Have uninstalled and reinstall the software and unplug the USB port and plug it back. Repeated several times. Still no communication. Exclamation red light next to 'on' and green button 'on' butter is flashing all the time.

  You have a hardware failure of the printer.  Contact the manufacturer for support.

• Encrypted L3 Communications between the TOWER and WLC?

  Hi all

  I work with a client who wants to put the towers away to their WLC (a 4402). The problem is that communications between the TOWER and WLC must be secured, even through their private Wan! I have a few questions that result, if someone is able to help you;

  1. I can't know if and what method of encryption is (is it AES etc.?) used on connections between towers and the WLC and what are the steps?
     1. The terminology can be a problem here, it's not a wireless mesh, just classic LAP for WLC
  2. EXTENSIVE customer network is already encrypted (IPSec VPN via VPLS) in parts - what is the consequence of execution of AP<-->WLC with end to end (if possible) on a network encryption EXTENDED with IPSec, i.e. double encryption?

  Strange but true - pointers will be greatly appreciated... Phil.C

  With a controller of the 4400 series, the control traffic between the AP and the regulator is already encrypted AES.  The user traffic is not encrypted.  If you use a 5508 controller all traffic between the AP and the controller is encrypted AES.

  For what is running the traffic through a VPN, it should work.  The issue I see with this is with the MTU in general.  The controller will drop all packets with a payload of less than 32bytes data.  According to the MTU over the VPN I've seen packets getting fragmented and it is a question.  If you use one of the versions CAPWAP (5.2 or newer) discovery dynamic MTU is part of the Protocol and this MTU problem does not really exist.

• No communication between the primary and standby

  Hello
  
  I have configured the DG,
  
  primary-> testprod
  standby mode-> testprod_s
  I started, standby machine instance watch with testprod and its place...
  but there is no communication between the primary and standby...
  
  How can I ask/check communication?

  Heartbeat PING [ARC3]: Unable to connect to the day before "testprod_s". Error is 12514

  eve of post form

  status of $lsnrctl
  $lsnrctl services

  When oracle not registered with listener service, this kind of errors occurred.
  The value of register LOCAL_LISTENER & manually as below in sleep mode and post

  SQL > alter the registry system;

• Disable communication between the host and the virtual machine

  I have VM Server 2.0 and one of the virtual machines has the same name as the server and even if the virtual computer is connected to the host only network it generates the Windows error message: duplicate names exist on the network.

  is there a way to disable communication between the host and the virtual machines? I just need a virtual network that is isolated from my network complete and host also.

  Thank you.

  The GUI Server2 is not to choose the other unused vmnets.  Then edit your file VMX use a different vmnet of 0, 1 or 8.  (which are bridged, host-only and NAT)

  Thus, for example, if your VMX has a line that says:

  Ethernet0.VNET = "VMNet0.

  change to:

  Ethernet0.VNET = "VMNet2.

  (This assumes that you have not used the network Editor to fill the vmnet2 either).

• Error "Unable to establish two-way communication with the device" Windows 8 with c309g

  Operating system: windows 8, 64 - bit

  computer: desktop

  Home network: network, the computer is on a wired connection, printer is on a wireless connection

  error message: "the computer is unable to establish two-way communication with the device.

  • When you install first of all my husband's new computer, we were able to install the software and connect the printer very well, and the printed test page.
  • A few days later, I installed the HP ePrint app on my iPad, found our printer and tried to print a page of a Web site. Printing failed, and the iPad app gave a message something like "the Word document may be printed." I cancelled again tried the iPad app, print work, and has not yet. I had not heard of AirPrint, so I did that on my iPad.
  • We tried to print the page of the computer instead, but the task has failed.
  • We looked at the parameters of the printer through the computer of windows 8 and found that there are two differently named c309g printer now displayed in the printer list.
  • My husband uninstalled the printer software, the computer restarted and reinstalled and then got the "the computer is unable to establish two-way communication with the device.

  any ideas on what to do next?

  My brilliant husband fixed it. Power cycling the router.

• I can't transfer file via airdrop between the macbook pro and my iphone 6.

  Hello world

  just bought a new macbook pro 2015 and I can't transfer file via airdrop between the macbook pro and my iphone 6.

  Can someone please help me solve this problem?

  Thank you

  < re-titled by host >

  First check the steps to run the drop:

  Use AirDrop to send the contents of your Mac - Apple Support

  There are some work around to try airdrop work:

  1. Turn off Bluetooth on your Mac.
  2. Delete /Library/Preferences/com.apple.Bluetooth.plist
  3. Re-turn on Bluetooth

  You can find more info here:

  Transfer and AirDrop does not work in El Capitan

  If you do not see all of your device, it means that you are affected by the same problem, I have known, since the upgrade to OS X the air drop of Captain does not work.

• Problem of the printer, I get "the computer is unable to establish two-way communication with the device.

  Original title: printer problem

  "The computer is unable to establish two-way communication with the device. I have pluged a all cables and pluged in that they return.

  Hello
   
  1. What is the brand of your printer?
  2. when the question is is produced?
  3. you remember to make changes to your computer before the problem?
  4. when exactly you get this error?
   
  I would temporarily disable all security software and check if the problem persists.
   
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
   
  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
   
  If you have an HP printer, you can consult the links below.
   
  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=&cc=us&DocName=c01868684&product=3737195
   
  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=&cc=us&DocName=c00301806&product=407677
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• U2415, around the gap between the Windows desktop and the edge of the monitor (bezel)

  Hello

  I have a Dell Ultrasharp U2415. I've read all the FAQS and I know I have to perform the SUBMISSION, but before doing so, I just want to know if it is normal to have a gap between the Windows desktop and the edge of the screen. If the Windows desktop is not covering or fill the entire screen. There all around the smaller than a 1/4 "gap between the edge of the windows desktop on the edge of the bezel of the monitor, and this model has almost no bezel. The graphics settings in Windows 10 are set to use the native resolution of 1920 x 1200 monitor. I tried with different computers (all windows 10), and the drivers are up to date. The monitor is connected via HDMI since I don't have portable computers not with DP interfaces. Laptop computers have Intel and ATI video cards. I have check the put option to scale on the video card software and it is set to 100%. So, is this gap normal? Is the edge Office Windows 10 supposed to touch the physical edge of monitors?  If the gap is not normal, I will perform the integrated test.

  TIA!

  Based on the YouTube comments, which seems to be normal. "But you must run the APPLICATION to see if the"smaller than 1/4"gap" appears. If Yes, then we can say that it is normal. If this is not the case, then some settings of the operating system is the culprit.

• DVD drive icon has disappeared from the Device Manager and my computer

  DVD drive icon disappeared from the Device Manager and my computer. I m using window 7. How can I get it back.

  Ashwani Hello,

  Thanks for posting on Microsoft Community.

  There are various reasons why a CD or DVD drive may not be detected. I would like to ask all of the steps in the Microsoft Article describes a troubleshooting and check if they help to resolve the issue.

  Your CD-ROM or DVD drive is not recognized by Windows or other programs

  Note:

  Before editing a registry key or subkey, we recommend that you export, or make a backup copy of the key or the subkey. You can save the backup copy to a location that you specify, for example, a folder on your hard drive or a removable storage device. If you make changes that you want to cancel, you can import the backup copy. For more information about backing up the registry, please see the link below.

  How to back up and restore the registry in Windows

  Hope that advice is useful. Let us know the State of the question, so that we can guide you further.

• What is the difference between the "Software Version" and "Version of the platform?

  I posted in this forum, because there is a maximum activity in this forum. Sorry, if this is not a good place to post this kind of question.

  What is the difference between the "Software Version" and "Version of the platform" of any blackberry device?

  My camera's curve 8900 and I can see in the menu About his version of software is 4.6.1.231 and the version of the platform is 4.2.0.108. What are these 2 versions for?

  Probably the best posted in the software section of the device, but is not serious.

  Version of the software/App - indicates the version of your applications (address book, browser, calendar, etc.).
  Version of the platform - indicates your version of system software (Java based software, radio code, etc.).

• What is the relationship between the main timeline and timelines of symbol in Adobe Flash Professional CC?

  I am new to Adobe flash and tried to create an E-card for a class. My teacher said that it is better just to have a keyframe for each layer in the main timeline and do all the clips of animation and film on the deadlines of each symbol. I'm having a hard time to understand how it works. To illustrate my confusion, let's start with an example.  I have a kite I want to start flying to frame 20. The kite is a symbol, so I create movement to 20 image interpolation in chronology of the wing. 20 on the symbol Timeline frame occurs at the same time as frame 20 of the MAIN scenario, or are they completely separate instances of time?

  Part of my mission, is should I use code snippets to add an element of interactivity to the Ecard. My confusion about the timeline affects my ability to do so. My teacher said that you need a stop on the first keyframe code to make sure that things will not start before you click the play button. Can I put the stop action on the main timeline or in the timeline of each symbol, or both?  Let's say I want to create a button that makes the kite flies when I click it. Where to play action 'go to and play', in the Assembly of the wing?

  I would greatly appreciate any help from the community. I'm the kind of person who needs to understand how things work. I searched for days, watch videos and read articles, but I still need to find a resource that effectively dissolved my confusion on this subject. So if anyone knows of any tutorials that explain how the main timeline and symbol timelines coincide, please share them with me. Thank you very much for your time.

  (P.S. are CC Animate Adobe and Adobe Flash Professional CC the same?)

  Thank you both for responding. Yes, your answers were useful, but a bit Advanced. I hope that you don't mind me asking a few follow-up questions.

  For Pete47-

  So I put my stop() in the main timeline. How the actionscript in the main timeline code works on the chronology of the wing if the two are separate?  Why not put the ActionScript on chronology of the wing? Clearly, there must be an interaction between the main timeline and symbols, right?  When you say "you can drag the symbol on the main timeline and it will run when you start", what do you mean by that? Like GETTING started, in the main timeline or in the scenario of the symbol? As you can see I am very confused by there!

  For Colin.

  I thought that Pete said you want to only have a keyframe in the main timeline. Then, when you said... "you can do it with an interpolation of the main timeline... from the beginning to the final position," why would you animate the motion on the main timeline? Why not in the chronology of the wing, can create another symbol of the tail in this period?

  And if the schedules of chronology and main symbol are separated, how SYNCHRONIZE you together different symbols to their movement to work together? And why should it be like that anyway?

  I am new to the community here, the last thing I want to say because you two sounds very knowledgeable on the Flash. How did you get your start? Did you start by watching the tutorials, read the manual, or something else?

  Once more, you have my abundant thanks for taking the time to help.