Composite test - problem with wsdl

Similar Questions

• Satellite P100-221: problem with driver battery composite microsoft

  Hello

  I have problem with my satellite p100-221! A few days ago I had problems with my audio driver (audio conexant high definition), after starting it was indicates that the pilot of his failed to initialize, I reinstaleed this driver several times and at last it was working OK, but I noticed that windows does not see the battery.

  The small cell in the status bar disappeared and I can not say for how long can I use laptop with battery. Laptop works as if it is connected to the AC. In the Device Manager appeared an exclamation on the battery composite microsoft.

  I tried to renew the drivers but nothing. I deleted combatt.sys and cmbatt.sys in windows\system32\drivers but they appear again. I started in safe mode deleted, but after normal start, they do not appear. I also deleted them in Device Manager, and after start-up, this device did not and do not ask me to install the drivers.

  What can I do?

  Hello

  I noticed that you did a lot of complex changes to your device. You deleted some files, update drivers, etc..
  I guess that your operating system has been enough installed and worked properly.
  Windows XP supports a system restore tool. This tool allows you to roll back the OS to the beginning.
  In my opinion, you should try to use this option. Maybe he'll bring your laptop at the time where everything worked correctly.

• problem with loopback test base with NOR-6008

  I recently started to use DAQmx in c# .NET 4.0 with NOR-6008 USB DAQ. I tried a loopback test by connecting output to an analog input analog and tried readign the signal from the output to the entrance but did not send the signal (or maybe a problem with the code). The analog input readign reads a random value rather than the value entered by the user for the output. I connected ao0 and ai3 on data acquisition. Here's the code.

  private void button1_Click (object sender, EventArgs e)

  {

  Task analogOutTask = newTask();

  AOChannel myAOChannel = analogOutTask.AOChannels.CreateVoltageChannel ("Dev1/ao0", "myAOChannel", 0, 5, AOVoltageUnits.Volts);

  AnalogSingleChannelWriter writer = newAnalogSingleChannelWriter (analogOutTask.Stream);

  Double analogDataOut;

  analogDataOut = Convert.ToDouble (AnalogOut.Text);

  writer. WriteSingleSample (analogDataOut, true);

  }

  Private Sub button2_Click (ByVal sender As Object, EventArgs e)

  {

  Task analogInTask = newTask();

  AIChannel myAIChannel = analogInTask.AIChannels.CreateVoltageChannel ("Dev1/ai3", "myAIChannel", AITerminalConfiguration.Differential, 0, 5, AIVoltageUnits.Volts);

  AnalogSingleChannelReader reader = newAnalogSingleChannelReader (analogInTask.Stream);

  Double analogDataIn is reader. ReadSingleSample();

  AnalogIn.Text = analogDataIn.ToString ();

  }

  Hello

  I built an application using your code (with task.verify) and it works beautifully.

  Have you tried different channels of inputs/outputs?

  

  Curt

• Problem with the composition of the corporate directory / phone book (E.164)

  Hello

  I have a little problem with the composition of the cucm phonebook integrated telepresence system. I can search the telephone directory, and it displays the user. The format is E.164 number, but with spaces in the number of empty? And for me, it looks like telepresence system trys to deal WITH areas because if I compose without space market. So it seems it is not the phone book to a good number E.164 number.

  any ideas?

  Concerning

  Jason

  Hey Jason,

  Looks like it's still an open caveat on the current software for MX, EX, endpoints series E20 and C sq.

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/software/TC5/Release_notes/tc_software_release_notes_tc5.PDF

  CSCtz87452:

  MX, EX, E20, C and SX Series endpoints cannot use directories CUCM with numbers, including spaces.

  Thank you, Adam

• Need of XLSX files tested to see if there is a problem with the content library

  Hello
  
  I have a file which causes an error when you use the library of Stellent. The file is a file XLSX and when we open and then save the file again, then does not cause the error. This leads me to believe that the file has been successfully created or something wrong with the library. More than likely it is the file. Is there any tool that I can use to test the file that will tell me what exactly is the problem? The file is automatically generated by a survey company. And so if we can show a problem with the file itself, then they will have to solve the problem in their autogenerator.
  
  Thank you
  Larry
  
  Published by: 1000345 on April 16, 2013 06:44
  
  Published by: 1000345 on April 16, 2013 06:45
  
  Published by: 1000345 on April 16, 2013 07:00
  
  Published by: 1000345 on April 16, 2013 07:00

  Which, in my view, that we use it for is to get out of text or metadata files to create an index on the data.

  Yes, it's also OutsideIn. I believe you can use the SDK to export research.

  If I were you, I'd do some testing base of the new version and it doesn't help, create a service request in Metalink so that management can take a peek inside.

• Problems with the Widgets Library / Compositions / presentation / Auto Play.

  I have a problem of failure when using the widget "Overview."

  The widget within the group is "Composition".

  With 'Auto Play' on...

  If I make a shortcut (button) to any element in the light table or use the options of 'Parts', 'Prev' or 'Next', continues to work option 'Auto Play '.

  I can only access other areas by direct click, it stops the 'Auto Play'.

  Can you help me solve this problem?

  Thank you very much!

  Hello

  Please take a look at this related post: http://forums.adobe.com/message/5551810#5551810

  See you soon

  Parikshit

• Problem with the license to test on both machines...

  I'm a developer looking.to.try.anew.development.IDE. I have two Win 7 Machines. On machine 1 install the trial went on a fine and DW, PS and I have been installed. This machine brings 30 days left in the trial when apps to start. He pointed out on machine 2, after installed, adobe application manager apps (I just installed on computer 1) ' day' (cannot be installed yet). FYI - Yes the logins and passwords to connect to adobe are the same for both machines. After researching the topic, I have cleaned with AdobeCreativeSuiteCleanerTool of the Adobe Site and reinstalled manager adobe application. Then the adobe application manager has indicated that all programs were available to 'try' but when I installed PS and started it - he said that "the trial is over - you can open just one more time" and now nothing opens. Therefore, machine 1 says 30 days trial and machine 2 it is expired? What I'm missing here? Your servers don't know my login ID (even) what's happening? It seems that track licenses Adobe has problems, and I fear that I will have problems with 2 machines after I commit to a year of monthly payments... Please don't even think to ask me to reinstall my system, or spend hours to install/uninstall registry tweaking, or trying this or that (in all fairness-ok software is complex I just haven't the time to spend hours to hunt the bugs with your software (I have enough debug with MY OWN CODE...)). I need a solution that I know I can count on the support of Adobe. Adobe's somone please answer this problem and help me to solve it as soon as POSSIBLE?

  Nothing you can do:

  Adobe trial software has expired at the beginning

  There is no support for tests in other...

  Mylenium

• database stress test - datagenerator problem with import data from oracle

  Hi all
  
  Today, I'm doing a stress test on my new server. Someone from this forum told me that there is a nice software for it:
  
  http://www.dominicgiles.com
  
  I have a problem with Datagenerator. I can't fill my user directly in the database. DataGenerator always has an exception. What ever...
  
  I tried to generate data on hard drive. It seems to go well. In the file data, I found a large number of files:
  
  *.dat
  *. CTL
  *. SQL
  
  N, anyone know how I can import only the files of user oracle?
  
  
  see you soon
  
  Dlugasx

  I do the table drop in the first place, I think it's to be sure, there are no objects before loading.

  Nicolas.

• Problems with WebCam? YouCam allows to test your WebCam

  Software using YouCam to solve your Notesbook WebCam problems

  Problems with your computers webcam portable? You can use the YouCam software to solve problems with your webcam. It was really only a few questions, which can cause problems with webcam. Driver problems, bad video configuration and software issues. YouCam will be able to identify these two problems for you.

  Troubleshooting with YouCam

  
  First you want to make sure that all other applications are closed. Other applications can steal the priority of the YouCam software that could interrupt the troubleshooting. Then open the YouCam software. If there are problems with the WebCam, you will be alerted with an error message here.

   

  "Unable to connect to the video device" error:

  Hope this helps to solve many problems of webcam. Again, this is an informational message that should serve as a reference. If you have gone over these steps and are still problems please create a new thread and include your computer model, operating system, and any other information that would be helpful in resolving the issue.
  
  Thank you!
  Sean S

• Problem with Unit Test

  What I am doing wrong?

  I created a small example of how to test the functionality of substitution of variables within the unit test framework.

  Documentation: SQL Developer: unit tests

  create or replace procedure SimpleTestProcedure (param1 in varchar2) as

  Start

  null;

  end SimpleTestProcedure;

  /

  Test configuration with the following configuration:

  Input value: Test

  Process: Boolean function

  declare

  Param varchar2 (4 char);

  Start

  param: =: param1;

  If "{param1}"! = param then

  Returns false;

  end if;

  end;

  

  Is found in the following message is displayed after the test run:

  

  I use SQL Developer Version 4.0.3.16.

  Any help would be appreciated!

  Kind regards.
  

  Hi Flofe,

  It looks like the Boolean function as a validation of process takes no parameters that a function pl/sql 'generic' put... it's probably called "function" only because it returns a value, as does any function. But you can use substitutions of setting the parameters for the stored procedure that you are testing, which you are already doing.

  So, try to change your code to:

  declare

  Param varchar2 (8);

  Start

  param: = "{param1}";

  If "{param1}"! = param then

  Returns false;

  on the other

  Returns true;

  end if;

  end;

  And it should work for try you the little test...

  I hope this helps...

  Val

• Logitech G19S problems with Windows 8 Pro x 64

  Hi all

  I have been a customer of Logitech for 18 years now and I've probably had more Logitech material than cooked dinners. And my latest purchase is the successor the Logitech G19 with the G19S awaited. Although it comes with a crazy price tag. It also comes with a nightmare experience, trying to get this device works on Windows 8 even if e t product has been certified to work with Windows 8, it caused an absolute headache get this 'thing' to work.

  For an eye untrained a novice, one would think that the keyboard has been installed twice. When actually the keyboard has not been installed twice, what it is for the keyboard, the other is for the USB ports and LCD for the keyboard. Although, to confuse the issue even worse. Windows sets the icon as two keyboard, when in fact it should have been G19 Gaming Keyboard then G19 Gaming Keyboard/LCD/USB because it does that confuse the issue. Examine the properties of the material, then you will have an understanding why there are two icons. My argument is that the description should be separated so do not cause confusion.

  +------------------------------------------------------------------------------------------------------------+

  | Keyboard game G19s

  | Device HID keyboard- keyboards

  | Human interface for the device of control of compatible consumer-HID Human Interface Devices

  | HID-compliant device - Human Interface Devices

  | Composite USB device - Bus USB controllers

  | Device-USB Human Interface devices

  | Device-USB Human Interface devices

  +------------------------------------------------------------------------------------------------------------+

  | Function USB Host Controller device

  | Status of the device: this device does not work correctly.

  +------------------------------------------------------------------------------------------------------------+

  +------------------------------------------------------------------------------------------------------------+

  | Keyboard game G19S

  | Device keyboard HID- keyboards

  | HID-compliant device - Human Interface Devices

  | Logitech G19 LCD - Logitech LCD

  | Composite USB device - Universal Serial bus controllers

  | USB Device input - Human Interface Devices

  +------------------------------------------------------------------------------------------------------------+

  | Function USB Host Controller device

  | Status of the device: this device does not work correctly.

  +------------------------------------------------------------------------------------------------------------+

  G19S keyboard (MAX 500mA USB Ports) which, when coupled with the USB receiver to the mouse G700S, looks like ports are overloaded because when you start Windows 8 sometimes with blue Windows Logo (no circle of spinning at the bottom of the page) I left to see if Windows will load , but noting. Unplug the USB cable from the port, and then restart Windows 8 with the USB cable removed it to load very well. reattach the USB cable from the keyboard to the back of your PC. Everything is fine until you turn on your PC again and it comes up with the same problem. What I've discovered, by removing the rear receiver is Receiver USB port to the front USB ports without the port of a USB docking station and just the small receiver of mooring. There is no interference, not crashing or the keyboard causing Windows crash when loading for the first time.

  I need to run tests more today and see if my theory is correct. But it seems that for the moment he is stable and I didn't have problems with the keyboard. I restarted the PC to see if there is a conflict at the initial boot to the top of the PC, and that's fine. It seems there is a conflict between the receiver for the mouse, then USB cable for the keyboard. It's in the same area that the keyboard, it causes Windows 8 to be unstable. If you move it from your PC. A small receiver coming out of the front of your PC is not intrusive. It is small and compact, so it doesn't show that much.

  The research that I did last night and this morning, it seems he had a similar problem with the predecessor the G19, I read articles and community forums with similar problems with Intel and AMD systems.

  I finally cracked and you are never in 1 million years think that would have been the likely cause of the problem. The G19S and G700S connected to the proximity to the other, caused the USB Bus overload. Me personally I don't see what is the cause... but, it works and it's stable and that's all that matters at the end of the day.

  The signal of the receiver G700S is 1000 Hz, which is much stronger than a wireless mouse normal that there are any lag or drop signal. Although, I found; with the connected connected to the USB docking station nearby renovator or next to each other caused the USB Bus overload. I moved the no intrusive receiver to the USB Port on the front of my rig and it is now very stable and load every time. It's the most bizarre experience I've ever lived, and now I know with certainty that the plausible cause of the problem was if anyone else has experienced the same problem as mine. Just remove the USB cradle for the receiver and plug the receiver into the front USB port of your platform.
  What a nightmare of an experience I will never forget. That you you prevented me troubleshooting for a whole day of Logitech.

• Problems with the program monitor for 20 to 90 seconds with project started in first CC2014 using CC2015

  I'm just finishing an important project for first Pro CC2015 and it tests my patience. Whenever I do an edit simple ripple and transitions program window to view side-by-side, CC2015 PP becomes somewhat insensitive for anywhere between 20 and 90 seconds. Sometimes it does not recover at all. When I say it's a bit insensitive, I mean I can always move clips, remove clips, or manipulate the clips in any way I want on the timeline. But the program monitor just sits on that same side-by-side view. The side-by-side never displayed the images while ripple editing is performed. The source window, audio mixer and lumetri litters all stop working. But they recover before the window of the program.

  This project was launched in 2014 CC and we should never have improved while in the middle of this project, but now it's too late to go back. It does this on two PCs at work and my PC at home. I started a new project, and no problem with changes to the ripple. Although there are minor, other performance issues, more generally I'm not happy about this day with first CC 2015. I also found a CC2014 project that will not export the correct proportions using CC2015, but just, we returned to the 2014 project to continue working on it.

  Number for ripple editing, eventually everything comes back and still works, but only once so far. Only once, however, my PC completely frozen and had to be returned. I built this PC at hand and never charge anything on what I have needed for my work. This is the first time that this PC has frozen more than 3 years that I used it. Sometimes, a program crashes, but never the entire system.

  Did anyone else out there having this problem?

  MY ADVICE: Finish the projects of CC2014 on CC2014! Stick with new projects with CC2015. or just hold off on upgrading.

  Hi Lisa,

  Disable "Composite overview for Trim" in the timeline view settings and see if that helps to run.

  

  Your Advisor not to switch versions of the programs in the middle of a project is the RIGHT HAND RULE of THUMB of video editing. + 1 for your advice.

  Thank you

  Regalo

• Problems with render (Prem 11 items)

  When I first import a clip in my project, the video quality is very good, but after I have make, he out craps, gets all grainy (the irony). How can I solve this problem?

  Sophie

  Part 1.

  Your Untitled.mp4 (turned)

  = AVCHD video compression

  Compression audio = AAC stereo

  Frame rate = 60 progressive frames per second

  File extension = .mp4

  Nominal value, it would seem that the project preset should be

  NTSC

  AVCHD

  AVCHD Lite 720 p 60

  In the first 11 elements, the program takes control over predefined setting the project given of some composite properties from the first video file dragged to the timeline. Sometimes it does, sometimes it doesn't. In no situation, it doesn't give you the project closet preset for you, but rather by default, its default value

  NTSC

  AVCHD

  Full HD 1080i30

  that does not correspond to properties of your video, including an interlaced 30 rate per second of the image instead of a 60 progressive frames per second an and including the size of the image of 1920 x 1080 instead of the size of your video 1280 x 720.  Why? It seems to be failing because it is having a problem with the frame rate. He is looking for a 59.94 to profile it and find 60 frames per second for your video.

  When boil us all this down to a few words. In this case, you must assign the project preset manually.

  First Elements ATR troubleshooting: PE11: accuracy of the project auto Preset setting (new project dialog box)

  When you do, you should be able to import your video into the project NTSC/AVCHD/AVCHD LITE 720 p 60 without the orange line on the content of the timeline despite this company of 59.94/60.

  Part 2

  When I import your Untitled.mp4 in a first elements 11 on Windows 7 64-bit project manually the value

  NTSC

  AVCHD

  AVCHD LITE 720 p 60

  the video quality seems good reading in the monitor of the area to change. And it doesn't have the ability to make this specific because the program its color line on the line of the capacity indicator tells me that I have the best possible overview of content (to get a better view). And, I found good quality reading display full screen also.

  Your Untitled.mp4 has a video bit rate (variable bitrate) of 5973 Kbps (kilobits per second in 5.973 Mbps. The size of the file is 41.0 MB).

  If you export your video Untitled.mp4

  Publish + share

  Computer

  AVCHD

  with Presets = MP4 HD720p60

  You should have a file whose properties are comparable to the source. The reading of this export of AVCHD.mp4 in the drive on your computer should be good.

  If for export file size considerations are not a problem here, you can increase the export export video bitrate settings tab button/video forward of the preset looking for a superior quality export.

  But, when all was said and done, I couldn't see not "grainy" before or after the reading of the Untitled.mp4 in the monitor area Edit. Export of this H.264.mp4 at no time looked grainy on playback in QuickTime player.

  Please review and consider. The double project preset controls, in particular the "Force selected setting on this project' checkbox in the dialog box new project when you perform the manual setting of the preset project. Please let me know what additional tests you need for your samples.

  Looking forward to your results.

  Thank you.

  RTA

• Problem with Framemaker 9 Dita XML Files in Framemaker 10

  I just upgraded to Framemaker 10. I meet a number of problems when trying to work with my help of Dita XML topics, that were last saved in Framemaker 9.

  1. using the default Dita model

  When I open one of my documents in Framemaker 10, the Dita 1.2 model ditabase.fm is automatically applied. Everything seems fine. But then when I convert the XML using Eclipse (which is essentially the html, so we go from XML to HTML format) using Dita Open Toolkit ant scripts, I see this message:

  [pipeline] [DOTJ013E] [ERROR] failed to parse the referenced file 'html\c_licensing.xml' cause from under exception. Please correct the base on the exception message reference.
  [pipeline] c_licensing.xml 25:Attribute 'xmlns:ditaarch' of the line must be declared for the element type "dita".

  Then, I opened the xml file in a text editor, and I saw this on line 25:

  < dita xmlns:ditaarch = "http://dita.oasis-open.org/architecture/2005/" > ""

  25 line seems to me. Am I missing something?

  2 go to a model of Dita 1.1

  I tried to get around the above problem. In Framemaker, I tried to put another structured as the default application. I closed all files and choose the structured Dita 1.1 application default (it defaults to the Dita 1.1. Composite app.)

  Then I tried to open my file: I got this message inside Framemaker:

  'Failed XML validation. Continue?
  Error to the [path of ACCESS], line 25, tank 72, Message: attribute ' {http://www.w3.org/2000/xmlns/} ditaarch' is not declared for the element "dita"

  Sounds familiar, isn't?

  I went from Dita 1.1 by default. Composite application structured with the Dita 1.1. Application of structured theme. Then I messed the source file and saved. The messages that I got in the FrameMaker log window included one above, plus I had a variety of messages to unknown element, things like:

  Element unknown dita.

  notion of unknown element,

  various attributes are not reported for concept,

  element unknown conbody.

  If I go to the Dita 1.1 mash all these messages diappear except this one:

  Attribute ' {http://www.w3.org/2000/xmlns/} ditaarch' is not declared for the element "dita"

  
  My conversion scripts of Ant in the Dita Open Toolkit are still unable to process this file. They give the same message as above in (1) and the file is not converted to HTML.

  
  Can someone help me with this problem? I also posted this question in the Group of users of Dita on Yahoo Groups. If I get an answer in one place, I'll post it in the other.

  Thank you

  Nina P.

  [transferred to dita-users]

  Hi Nina...

  The xmlns:ditaarch attribute must be the "topic" not dita root element. If demand for FM10 structure is the award that it is wrong. You create composite themes (multiple topics in a single file under the root of dita)? If this isn't the case, you can get rid of the total dita element and who can "solve" the problem.

  The first mistake you get (#1) says that the xmlns:ditaarch attribute must be declared (that is, defined in the DTD)... It's not (because it is not supposed to be there (as I know). This is not to say that it must be declared in the DITA file.

  Even for the #2 error... the composite 1.1 app is apparently set up correctly, so it's saying the same thing that the Old Testament said... "you have this attribute in the XML file, but it is not declared in the DTD.

  Your subsequent error on the missing items is because you spent in the "topic" DTD, who does not know the dita element or elements based on concepts.

  If you can unpack your files dita element (because you are just using a topic in each file), which can solve the problem. But you probably need to do is open these files in a text editor and remove the attribute of xmlns:ditaarch of them (he not really needs on the elements of the topic either since it is the default value). Then, I turn to the composite 1.1 as a default app. I'll take a look at the FM10 1.2 default app and see what happens. (I have not seen this problem since I was on DITA-FMx, which has its own structure of apps).

  See you soon,.

  .. .Scott

  Scott Prentice

  Leximation, Inc..

  www.leximation.com

• Problem with Blackmagic DeckLink HD Extreme 3D and Premiere Pro CS 5.5.1

  Hello

  I'm having a problem with the first and Blackmagic DeckLink HD Extreme 3D. When I create a timeline of Blackmagic of any sort and I import a film and start working on it, everything works as expected and are quite fast. I can see the image in the window of my monitor and the output to the external display of JVC is excellent (SDI). If I create another new project and in there I create a regular first screening chronology (in this case to edit Canon 5 d MKII footage) I can also change without problem (and with even better named Update).

  The problem appears when I try to have a timeline for Blackmagic and a predefined regular creation timeline in the same project. If I create the chronology of Blackmagic first, I can import and edit, but at the moment I have create a first preselection timeline screen goes black for a second (which always happens btw) and then comes back again. So I can edit the first timeline screening perfectly but the chronology of Blackmagic image stopped appearing in the monitor window. I can play, I can hear and I can see it in the external monitor of JVC. But on the computer screen the only thing I see are images that paint on it and somehow stuck in there get it looks like some sort of overlay problem. After that if I close first he won´t close properly. I have to force it out. If I first create a first timeline preset that works just fine but when I create a timeline of Blackmagic this work won´t (the first timeline works fine)

  So, my guess would be that first pass to a certain color depth or space when creating a first screening chronology and for some reason any the Blackmagic card won´t adapt or update so I find myself with no picture and the remains of some images that I place on the monitor window area. I can see the scopes and all waveforms but not the video. Also perhaps monitors and display port adapters have something to do. I'll change soon so monitors would be nice to know if it's part of the problem.

  Any idea? Waiting to hear from Blackmagic too.

  My specs:

  MS Windows 7 64 bit SP1

  Card mother TYAN S7025

  Two-processor Intel Xeon X 5650 @ 2.67 GHz

  32.0 GB Triple-Channel DDR3 @ 533 MHz (7-7-7-20)

  Graphics NVIDIA Quadro 5000

  System drive: 125 GB KINGSTON ATA (SATA) Device

  The data disks: Seagate 2X1954GB (SATA)

  Seagate 2x977GB (SATA)

  External Lacie RAID 5 TB (for backups)

  My monitors are 2 Apple Cinema HD 1920 X 1200, connected via 2 ports of graphics cards.

  BTW, this problem appeared before the named Update.

  Thanks in advance.

  Sergio Rozas

  www.usert38.com

  http://blog.usert38.com/

  I had a similar problem with a Matrox card.  The solution was to turn on the composition of the bureau.  It is under properties - TAB, show - system on the 4th in the advanced settings list.  Some programs (for example AVID) insist on this being extinguished, but with CS5.5 I needed active.  I have not tested this with dark magic devices.  It don't has not caused me a problem with CS5,