Consider the value of imports DVM

Similar Questions

• Is the value MHz important when buying memory?

  A a site specialist Web memory told me I need memory DDR2 533 MHz (pc2-4200) 200 next pinSODIMM

  I thought that it is better to buy a toshiba retailer so I checked the world pc and curries etc. I found a module of memory similar to what I mentioned above - but the MHz is different - its 633 MHz... So I was wondering is it OK to buy this module, or should I stick to 533 MHz?

  Thanks for any help

  Hello

  The MHz value memory tells you how fast the modules can operate.

  But very important is the FSB value. Memory speed depends on the bus (FSB) front if the FSB supports substep MHz (IE. FSB = 553 MHz and memory = 667 MHz) then the modules of memory would go only with 553 Mhz.

  Also if you mix different bars with different speeds, then the two modules would be using lower speed. Simply said the slower module would slow the module second, faster.

  Greetings

• Canon 5 d Mark ii Images with the value of the white balance fixed. When they are imported into Lightroom, the value is different.

  If I take a shot with the fixed value of 5200K WB (5 d Mark ii) and import into LR 2015.2.1, happens to 4850K. No presets or applied adjustments.

  No idea why? How can I solve this problem?

  Rich

  All raw converters use four multipliers of white balance RGGB tinted and embedded in the raw file EXIF data to set the white balance and 'calculate' the temperature values displayed inside the module development LR WB.

  Scroll down to the "White Balance" section of the DCRAW tutorial PDF here: GUILLERMO LUIJK > TUTORIALS > DCRAW TUTORIAL it's all so raw converters all the rest of the white raw file and 'calculate' the temperature and tint values.

  Here is a Canon 5 d MKII CR2 file with the White Balance adjustment 'in the know' behind closed doors:

  (Data EXIF Maker Notes)

  

  The setting "As Shot" WB in LR shows a Temp of 4800 reading, which should produce a slight visual difference that the planned in-camera closed 5134 parameter, correct?

  

  However, with the LR settings file, "As Shot" above the white balance CR2 is the JPEG file in camera perfectly on my Canon 5 d MKII (raw + JPEG file format). It's just that Temp readings do not, because they are "calculated" four RGGB multipliers. Each raw (LR, opening, C1) converter will probably show the values of temperature and tint different, since they are derived by using "reverse engineering" of the manufacturer of exclusive camera raw data structure and camera sensor response file.

  Keep in mind that the spectral response of the camera is affected by changes in batch. A Canon 5 d MKII body can produce slightly different WB as one another using the same exact settings. Rather than depend on private clos or LR presets use a good white balance card or the ColorChecker Passport to 'calibrate' LR white balance settings standard shooting conditions (daylight, cloudy, Flash, etc.). For critical projects draw card of the white balance at least once for each unique lighting condition. You can then determine the correct inside the LR setting and settings of synchronization of the World Bank through all the images taken with this specific lighting.

• FormsCentral is throw the value of exports dropdown when you import PDF form

  I would like to communicate that I'm pretty new to this process.

  I created a PDF to a word document. After creating the form in Adobe Acrobat Pro XI part and adding javascript validation and calculations mainly from these community forums I encounters an error when importing the form of FormsCentral.  I have drop-down lists that contain numbers (1,2,3, etc.) to choose the amount of guests will invite the recipient. In turn, selecting a number, the value of exports ($100, $ 200, $ 300, etc) will be displayed in a text box adjacent indicating in quantity, what it will cost.

  It works fine in Acrobat, but when I import I get a message:

  FormsCentral was able to import the PDF file with the following exceptions:

  The choice field that contains an AddtD displays and exports values. FormsCentral must ignore export values, and this can cause existing calculations and validations to fail.

  The choice AddtG & D field contains both view and export values. FormsCentral must ignore export values, and this can cause existing calculations and validations to fail.

  When it comes to efficiency, I am aware that I can do things the tedious way. But I want an idea on how to make the most active text box in this scenario. I will include my properties / validations and calculations:

  Drop-down list 1 (AddtG-D): export values, such as discussed above

  Box 1 (TotalAddtG-D):

  Validation script:

  NULL filed value if the input is zero

  if(Event.Value == 0) event.value = "";

  Custom calculation script:

  Set this field to the value of the drop-down list box

  Event.Value = getField("AddtG&D").value;

  Goes the same for the drop-down list box and 2 2, because they are the same. Any help would be great!

  This is an unfortunate limitation of FormsCentral. I don't know really the reasons to make it, because you can use JavaScript to set export values after download and it works great. But a better approach is to use not the value of exports and to modify the scripts to make up for it. This is usually done with a lookup table to associate a value dropdown with what would normally be its export value. If you provide a list of your values in drop-down list and the corresponding values for export, I can post a sample script that you can use instead of what you are currently using.

• How a value is to consider the change of dblink to the web service?

  Implementation of SOA and OSB, how a value is to consider the change of dblink to the web service?
  
  Where I work, there are a large number of dblink between databases. Some dblinks are intended to be the way to load the immense amount of data while others exist only to simple queries.
  I wonder if it might be better to use web services as dblink. In principle, I think that simple queries may be suitable as a web service to improve reuse and governance but I find web service not apropriated for loads of data.
  Obviously, the decision is more complex that just think tecnology. Despite this, it will be useful to hear if there are people around the world think about change dblinks to web services the same load so heavy querys with a small amount of data to be trafficked and this as the principles, models or reasons behind this decision.
  Basically, we are implementing SOA and OSB and I'm looking for the best I can to rethink the way we used to do it so far. I heard from a friend of mine that we must avoid using dblinks and use only the web services. This seems strange to me because I wonder what level of overloading by the net, that we will face. Could someone give your personal opinion or propose an article? There are some pros and cons, formerly on this review?

  966355 wrote:
  My question is: wouldn't I tend to turn the worst of communication when I change the dblink in scenario 1 and even more terribly worse in scenario 2?

  Yes, this is a drawback... You can't get better performance by adding more load, unless you bring better infrastructure...

  One more detail: in scenario 1, there is a high probability to be reused by other systems.

  It is one of the beneficial results you have to weight against your disadvantages...

  In scenario 2, it is not reused, but we need to audit and traceability of the integrations like this.

  This scenario looks more like ETL integration... It's a bulk data loading, you can take a look at ODI - Oracle Data Integrator (ODI is also part of the Fusion Middleware)

  In my view, the main issue is to have systems so closely coupled... Systems get older, they get out of support, seller will declare a version is end-of-life, then you need to update. The system vendor has don't might not mind system B accesses its internal tables, but if they decide to change the internal database on the next version, they do... And then you're stuck with the vendor and version...

  I hope this helps...

  See you soon,.
  Vlad

• DVM loopup, without using the value to hardcode in playoffs

  Hi gurus,
  
  I use dvm in xslt. My code works fine when I use the value of hardcorded in search of dvm as qualifier. but my requirement is whatever number arrives in payload, it should act as a qualifier. Here I am using following code, compile and run, but every time I get the same output "NOTFOUND".
  
  
  Could you please solve this problem...
  
  
  < name of xsl: variable = "InterchangeSenderNumber."
  Select = "normalize-space(/ns0:Transaction-850/ns0:Internal-Properties/ns0:Data-Structure/ns0:Lookup[@Name ="InterchangeSenderID"])" / >
  < name of xsl: variable = "InterchangeReceiverNumber."
  Select = "normalize-space(/ns0:Transaction-850/ns0:Internal-Properties/ns0:Data-Structure/ns0:Lookup[@Name ="InterchangeReceiverID"])" / >
  
  
  <xsl:value-of select='dvm:lookupValue("EDIOrderFDM.dvm","Ordertype",/ns0:Transaction-850/ns0:Segment-BEG/ns0:Element-92,"SoldtoCustid","NOTFOUND","SenderID","$InterchangeSenderNumber","ReceiverID","$InterchangeReceiverNumber")'/>
  
  
  Concerning
  Francis

  Hi Francis,.

  Francis wrote:
  

  The variables are cited... use $InterchangeSenderNumber instead of "$InterchangeSenderNumber"...

  See you soon,.
  Vlad

• Value of imports in from the text Imput field

  Hey I want to ask something. In this countdown code that I placed below. He has an exact value of count. My question is how a user can enter his own values of countdown to input text fields? The entire .swf looks like this: first, the user opens the screen it enter its value for the minutes and seconds in the text entry fields and the countdown begins then how link text input fields to import the value of minutes and seconds in for the countdown? pls help

  Here is the Code that I use for the time count:

  start_time = getTimer();
  Countdown = 600000;
  onEnterFrame = function () {}
  elapsed_time = getTimer () - start_time;
  _root. Count.Text = time_to_string (elapsed_time);
  _root.count_down. Text = time_to_string(_root.countdown-elapsed_time);
  };
  function time_to_string (time_to_convert) {}
  elapsed_hours = Math.floor (time_to_convert/3600000);
  remaining = time_to_convert-(elapsed_hours*3600000);
  elapsed_minutes = Math.floor (remaining/60000);
  remaining = remaining-(elapsed_minutes*60000);
  elapsed_seconds = Math.floor (remaining/1000);
  remaining = remaining-(elapsed_seconds*1000);
  elapsed_msecs = Math.floor (remaining/10);
  
  If (elapsed_hours < 10) {}
  hours = "0" + elapsed_hours.toString (); "."
  } else {}
  hours = elapsed_hours.toString ();
  }
  If (elapsed_minutes < 10) {}
  minutes = "0" + elapsed_minutes.toString (); "."
  } else {}
  minutes = elapsed_minutes.toString ();
  }
  If (elapsed_seconds < 10) {}
  seconds = "0" + elapsed_seconds.toString (); "."
  } else {}
  seconds = elapsed_seconds.toString ();
  }
  If (elapsed_msecs < 10) {}
  Ms = "0" + elapsed_msecs.toString (); "."
  } else {}
  MS = elapsed_msecs.toString ();
  }
  
  "return minutes +": "" + seconds + "'." + MS; "
  }

  assuming that you use a movieclip button (named countdownBtn) to start the countdown and your input textfields are minutesTF and secondsTF, use:

  countdownBtn.onRelease = function() {}
  start_time = getTimer();
  Countdown = 60000 * Number (minutesTF.text) + 1000 * Number (secondsTF.text).
  this.onEnterFrame = countdownF;
  }

  function countdownF() {}
  elapsed_time = getTimer () - start_time;
  _root. Count.Text = time_to_string (elapsed_time);
  _root.count_down. Text = time_to_string(_root.countdown-elapsed_time);

  If (Number (_root.count_down. (Text)<>

  delete coundownBtn.onEnterFrame;

  }

  };
  function time_to_string (time_to_convert) {}
  elapsed_hours = Math.floor (time_to_convert/3600000);
  remaining = time_to_convert-(elapsed_hours*3600000);
  elapsed_minutes = Math.floor (remaining/60000);
  remaining = remaining-(elapsed_minutes*60000);
  elapsed_seconds = Math.floor (remaining/1000);
  remaining = remaining-(elapsed_seconds*1000);
  elapsed_msecs = Math.floor (remaining/10);
     
  If (elapsed_hours<10)>
  hours = "0" + elapsed_hours.toString (); "."
  } else {}
  hours = elapsed_hours.toString ();
  }
  If (elapsed_minutes<10)>
  minutes = "0" + elapsed_minutes.toString (); "."
  } else {}
  minutes = elapsed_minutes.toString ();
  }
  If (elapsed_seconds<10)>
  seconds = "0" + elapsed_seconds.toString (); "."
  } else {}
  seconds = elapsed_seconds.toString ();
  }
  If (elapsed_msecs<10) {="">

  
  Ms = "0" + elapsed_msecs.toString (); "."
  } else {}
  MS = elapsed_msecs.toString ();
  }
     
  "return minutes +": "" + seconds + "'." + MS; "
  }

• How do we use getDataObjectContents to import the value of the fields of an attachment

  Hello world

  I tested this method on how to get the value of an attachment and place it on the current page open, I tried to do: http://cjoint.com/13dc/CLruaj192OV_doc1.pdf

  using the example on the AJS reference, but it does not work could you please help me understand the question

  var oDoc = this.openDataObject("attachment1");
  try {
  
  var myField = this.getField("Text");
  
  // get the value of "MarksTotal1" in PDF attachment
  
  var yourField = oDoc.getField("MarksTotal");
  
  // view this value in "Text"
  
  myField.value = yourField.value;
  
  oDoc.closeDoc();
  
  } catch(e) { app.alert("Operation failed");}
  
  

  tanks a lot

  Use this code:

  var oDoc = this.openDataObject ("attachment1.pdf");

  try {}

  get the value of "yourTextField" in PDF attachment

  var yourField = oDoc.getField ("MarksTotal");

  See this value to 'myTextField '.

  YourField.value = Event.Value;

  oDoc.closeDoc ();

  } catch (e) {app.alert ("the operation failed") ;}}

  To ensure that you have the name of the correct data object, you must Access the document dataObjects property.

• Changing the values of the project

  Summary

  Here change the link reference and report Suite fields or be able to migrate all between projects. Lack of one of these options, I want to know that the values of these fields don't really count.

  Example values:

  	Basic reference: link	Analytics: report Suite
  DPS 2014 App	com.mycompany.MyApp	com.mycompany.MyApp
  AEM Mobile App	com.mycompany.myappdev	com.mycompany.myappdev

  The correct values have been changed to protect the innocent.

  Details

  Currently, we had weeks of progress by creating a new application AEMM to replace our DPS 2014 application. The problem that has developed is the AEMM project, we created have values of different parameters in two places which do not match the existing application of DPS. Because we couldn't find a way to change these values, we have created a new project with the correct values. Once we did that, we discovered that there is no way to move content between projects. So we are facing days of work to address this problem. That's assuming that the values of these fields have an important effect.

  Questions

  1. What are the effects happen to have value do not match in the field link reference? Reading this forum leads me to believe that the feature gives even does not yet.

  2. What are the effects happen to have value do not match the scope of report Suite? I still have to find a good reference for analytical how will be between these two editions of the DPS/AEMM.

  You want solutions

  1. in an ideal solution, we could get help from Adobe to fix the values in the original draft of AEMM

  2 or a way to pass the work weeks of the old AEMM project to the new, corrected one.

  3. we would be willing to leave the values as they are, provided it would have serious consequences.

  4 and if this is not possible, we will have to carefully recreate the settings in the new project, using the old as a guide, the hierarchy and content.

  Short answer: continue to use the previous project. You don't have to worry about these values for the migration.

  1. What are the effects happen to have value do not match in the field link reference? Reading this forum leads me to believe that the feature gives even does not yet.

  That is right. The reference link field is not supported at the moment, so there is no problem having a value do not match. (Link reference was intended to be used for the deep link outside of the app, but right now, we use dps. .)

  2. What are the effects happen to have value do not match the scope of report Suite? I still have to find a good reference for analytical how will be between these two editions of the DPS/AEMM.

  During the migration of DPS to AEMM, it is good to use a different value in the field of the report. Both platforms use different methods to collect Analytics requires different reports. If you have Adobe Analytics, you will want to ensure that your analytical information is implemented correctly in the master settings. If you need assistance with setting up Analytics, contact Adobe support. Support information are available when you connect to the portal using a master administrator account.

  Another question that you did not mention, but might want to consider. When you build your application, you specify a Bundle ID. When you build your Mobile AEM application, it is important to use the same Bundle ID you used when you build your DPS application so that you can update in the store. In addition, it is a good idea to use the same Bundle ID for Android and iOS apps for certain services such as In - App Messaging.

  Migration resources:

  Strategies for the improvement of DPS to MEA Mobile applications

  Migrate the content of folios DPS for AEM Mobile

  I hope this helps. Let us know if you have any other questions.

• Change the name of the file of "Import.xls" selection in Applescript

  Hi, I'm a tiger, but I try to change the name of a file in a folder (which can be any name that is) a name known.  In the end, just trying to import a file known to filemaker and need the name to be a known name.  That's what I have so far, but I have simply not success.  This goes to the folder 2 window and selects the first file... no problem, but, I can't seem to change the name of 'import.xls '.  Only excel files will be present in this folder, so I'm not worried about it.

  The other thing I would do is if there is no file in this folder to jump above everything and do nothing.

  Thanks for your help!

  Tell application "Finder".

  activate

  the value target of Finder window 2 to folder "Orders_to_Enter" of folder "Documents" of the file 'MINIJOHN'from folder 'Users' of startup disk

  Select the first file of the window of Finder 2

  Try

  the value the name of the selection of "IMPORT.xls".

  end try

  end say

  
  

  say

  Hello

  No need to manipulate the selection. You can just write something like this:

  set d to (path to documents folder as string) & "Orders_to_Enter:" as alias
  tell application "Finder"
      --open item d -- optional
      tell (item d's file 1 whose name extension = "xls")
          try
              set name to "IMPORT.xls"
          end try
      end tell
  end tell
  

  Tested under OS X 10.6.8.

  Good luck

  H

• Does not restore the values of form for the restoration of the tab

  Part of my Web site uses a large number of forms on a single page. On the page, you can filter items (each item has its own form) and modify them. One entry looks like this: [name] [select status] [other Select]. Other important things are that the document has an expiration date in 1981 (to apply a page always up to date) and that change the value in the select results in the triggering of an AJAX function.

  It works perfectly, except for one thing. When filtering State id 1, you get back a little of the element. Let's say that the result of the filter are input 5. Change entry #2 status, which triggered an AJAX function. It works very well, but here's the problem: when close the tab and re-opening with Restore tab, select values become disheveled.

  Due to the execution of a fresh copy of the page, the browser will get a new copy of the page. Entry #2 is now gone (I'll keep calling it that, even if she disappeared because of the filter). Now, here's the problem: Firefox is attempting to restore the value to select it. Entry of the status #3 now has the same status of entry #2, #4 a #3 status and so on.

  I managed to solve this problem on other browsers (Chrome, IE) with this little piece of jQuery:
  {$(document) .ready (function ()}
  {$("form[class^='startingformname']").each (function ()}
  This.Reset ();
  })
  });
  It works perfectly, except for Firefox, which seems to ignore the call to reset...

  As this text is quite long, I'll keep my short question: How do you keep Firefox restore the values of the form (preferably: keep them on the selected item in the HTML)? Now, the user always gets a new copy of the page, and Firefox is trying to restore the old values on this page, even though the HTML code has changed.

  I think your two choices is:

  (1) prevent Firefox from page caching, or
  
  (2) use a different event to trigger your reset function

  As I understand it, the function $(document) .ready jQuery () raises the event DOMContentLoaded (or equivalent, if not supported by the browser). If the tab is cached in its ' cache fast back-forward ", Firefox can not fire this event when the user returns to the tab, just like Firefox does not always raise the load event in such cases.

  Discover the event more described in the following article and see if you can use it to trigger your reset function in Firefox: https://developer.mozilla.org/docs/Using_Firefox_1.5_caching

  Who is?

• Formula to find the value of the channel

  Hi all

  Support: Dat file containing the value of time and acceleration. Now, there are only two Channels.  Channel 1 is time. Channel 2's acceleration.

  Step 1: Create more than two channels. Channel 3 and channel 4

  Step 2: go to the analysis and acceleration channel research where its value is reached xxxxxxxx 1.

  Step 3: where it has reached 1. XXXXXXXX in the process of accelerating from this point in the channel 3 and 4, paste all the values STD. STD values in the attached excel file.

  How can I do this? What is the formula or the script to do this?

  Thanks in advance.

  Hi Rash.patel,

  You didn't yet tell me where to find the Excel file, so I assumed it would be in the same folder as the VBScript script.  I used the DIAdem Excel Import Wizard to create an *.stp file that can be passed as parameter in the ExcelImport() command to load these curves 2 envelopes by program.  I also added a file dialog box, then you can select the *. DAT to deal with file.

  I think that's

  Brad Turpin

  Tiara Product Support Engineer
  National Instruments

• Assistance needed for the registration of the application and store the values in a table

  Hello

  Hope that this explanation is not confusing. I explained my application you want in the text below and also attached a skeleton VI + screenshot hoping that he will clarify

  I try to do a VI that does the following:
  1. some code (blue Subvi) runs every 200ms
  2. every 200ms, a random number is generated
  3. the random numbers are stored in a table in intervals of time s 0.8 ("iterations")
  4. at any time, the (blue Subvi) code needs to have access to the random numbers generated in 'the previous iteration.

  To clarify, the iterations are as follows:
  Iteration #1: 0 - 1.8 s
  Iteration #2: 2 - 2. 8 s
  Iteration #3: 3 - 3.8 s

  Iteration #4: 4 - 4.8 s
  ..
  And so on...

  So for each iteration: the blue (Subvi) needs to have access to the random numbers generated in the previous iteration, for example:

  Iteration #1 (0 - 1.8 s): The blue (Subvi) Gets an array that contains only the zero (random numbers are recorded for the first time)
  Iteration #2 (2s - 2 8 s): The code gets an array containing random numbers of iteration #1
  Iteration #3 (3 s - s 3.8): the code gets an array containing random numbers of iteration #2
  Iteration #4 (3 s - s 3.8): the code gets an array containing random numbers of iteration #3
  ..
  And so on...

  At any given time in time;
  -The code gets an array that contains all the random, recorded during the previous iteration numbers
  -Values since before her previous iteration are ignored and not stored anywhere

  Thus, for example, to the #7 iteration:

  -The values during the iteration #6 are made available to the code in the form of a table

  -Values of #1 to #5 iterations have been deleted and not stored anywhere

  It is important that all values since before recording the previous iteration are deleted because they are not necessary because VI actaual will work for a long period of storage of numbers a lot more than I have indicated here

  Screenshot of the skeleton VI:

  

  I tried to play with the paintings, the structures of the case and the registers at offset, but everytime I try I get something wrong

  The skeleton VI is also attached (Iteration_VI and Code_SubVI)

  Any suggestions?

  Thank you!

  Yes, I agree that you need help.  First of all, you really do need to learn more about LabVIEW - spend a few hours with the tutorials, such as those mentioned on the first page of the Forums.  Oops - links to the tutorials which had been present for years seem to have been moved "elsewhere" with August 2016 LabVIEW community reorganization.  But look for them...

  Here are a few screws that basically implement what I described above (with some minor modifications).  First of all, this is a Top level VI which runs at 5 Hz (200 msec waits).  It starts with an array of 5 elements of 0, then once per second, this is replaced by a table of random numbers generated by the Random 5-table sub - VI 5 elements.  Note that I do not use a loop timed - those who are really designed for LabVIEW RT, but use the simplest functions on the Palette of the timer.

  

  Can't you see how that works?  The array to initialize on the left begins you with a table of 5 elements of 0.  The Timer inside the loop, it runs at 5 Hz, 'Index' counts 1, 2, 3,... to tell you where you are, and 5 shows you everything that lives on the shift register.

  Now sub - VI Random 5-table is supposed to do the following - if she was called to 5, 10, 15,..., it must return a (new) array of 5 random numbers, otherwise, it must return the array that was passed in.  So if all "works", table 5 shows 0, 0, 0, 0, 0 for the first second, a table at random for the second second (which is not superfluous!), a different for the third random picture second and so on.  I have already said a way to build this, but I chose a slightly different method (equivalent).

  

  Whenever it is called, a new random element is generated and added at the end of a (growing) random table stored in the shift register.  If size become 5, we send this Random-table-of-5 out through Out table and reset the register shift to an empty array.

  The case by default (when the size is not equal to 5) is shown below - we just return the array of entry to and accumulate new random table in full growth.

  

  These code fragments extracted from VI.  If you have LabVIEW 2016 (see the "2016" at the top right of the image?  This shows that it is a snippet of code LabVIEW 2016), you can open a blank diagram and drag this image, where magic OR converts it to a VI.  Otherwise, the code yourself and try out it.

  Caution - it is designed to run once.  If you run the program of high level, a second time, you may find that the new Random 5 - table appears to 0.4 ", 1.4", 2.4"(instead of 1", 2 ", 3").  I leave as an exercise for understand you to (a) why he is and (b) fix the code.  If you can't do that, then move an another 3-4 hours with the LabVIEW tutorials (or start playing with this code, edit it in some small way and to understand how it works).

  Bob Schor

• How to set the limit function, means I want defined logic that when the value is between 0 to 0.3 loop and then stops.

  Hello

  I'm looking for the logic as the way to define the logic of upper limit and lower limit.

  Means that there is only one indicator of entry in which a user can enter any value, I want that when the user gives value between 0 and 0.3 for example while then loop will stop other wise, it will work on an ongoing basis.

  Please guide me.

  Thank you very much.

  Please consider the VI below.

  

• Why no event to CHANGE the VALUE?

  LV2013, Win7

  The attached VI does not work the way I expected.  I wonder what can be done.

  My real program (this is not it) has a window with a menu.  You modify alarm settings in this window.

  It uses a menu with NEW, OPEN, REVERT, SAVE and SAVE as.

  I want to offer a word of caution: If you change the file on the screen, then try to REVERT or NEW or OPEN, you get a dialog box that the file is "dirty", i.e. has unsaved changes, and you can cancel and continue nevertheless, or save and move forward. "

  I also want to disable certain menu items if the file is dirty.

  Most of the time, it works very well.  But there's an edge case that I can't do work.

  If you run this program, change the string, then (as the very next thing) click on the FILE MENU, then the menu is not save the file as dirty.

  Even if I have a test 'dirty' right there in the ACTIVATION MENU, and he gets executed before the menu appears, it is not as dirty.

  The menu is so bad, and as soon as you click an action, the action can still see DIRTY as false.

  Now, if you change the string, and then click turn OFF somewhere, the VALUE CHANGE event happens, and she is considered unclean.

  But if you take a file, type something in and immediately, click on the menu (or type ctrl-O) then it is not recognized.

  Any ideas how to get around this problem?

  Before I tell you to turn on the VALUE UPDATES while TYPING, know that it should work on numeric fields, where there is no option.