County to return read VISA does not match number of bytes
I encounter an error with a VISA reading. I ask 8 bytes (in number of bytes), but get only 7 return (return number), which causes errors in my code downstream. Curiously, the VISA Read block does not return an error. Any ideas on how to debug this?
Data sheet:
LabVIEW RT 8.2
VISA 4.3
Series OR 3.3.0
PXI-8431/4
Parameters: 1843200 Baud, 8N1.
Is VISA reading set to put an end to the reception of a termination character? I think that it does not have the stop in the output string character, which could make your short back counter.
Lynn
Tags: NI Software
Similar Questions
-
Possible reasons:
Scripture cannot be performed because the number of data channels does not match number of channels in the task.
When writing, provide data for all channels in the task. You can also change the task so that it contains the same number of channels as the written data.
Number of job channels: 8
Number of data channels: 1Lama says:
The DAQmx vi writing gives me the error. If I run a single channel, isn't a problem. Multichannel gives me error.
You are funny! Why tie yourself to work VI (single channel) instead of one that gives you errors (multichannel)?
(If your car does not work, you bring car your wives to the mechanic, right!)
What is the exact text in the multichannel 'physical channels' when you do the AO control?
Lama says:
I did a sequence to ensure that each function has been run in the correct order. Wouldn't a race condition.
All you have to do is wire the 'start of task' error at the entrance of error of the DAQ assistant and then back to 'stop task' and things will run in order. Guaranteed! Think the stream! Everything else can run in parallel or the order is irrelevant.
First convert the sequence stacked to a sequence of plate, remove the flat sequence and add the mentioned son. Now, do a "cleaning pattern.
A when stacked with the inhabitants of the sequence is one of the worst construction you can possibly do. It makes the code difficult to follow, impossible to maintain, difficult to debug.
-
Read visa does not read as specified in bytes read
Karine says:
Thank you Jeff Bohrer
say that I have to wait frame sequence delete and replace with delay?
Best regards
That and stop playing with hardware flow control RTS - CTS will do it for you
-
My VI works as a motion detector. Whenever the motion detector is activated, the led lights up and a beep is heard (a switch will exercise my motion sensor). Once all the lights are on, the system reset is supposed to light up, and then the other three lights turn off back waiting to be activated once more. My attachment saved as "sensor project", I have the VI working with data acquisition by implementing a case of random number, and the VI works here to give a demonstration of what I'm trying to work in favor. Any information would be greatly appreciated.
You have some problems of logic and data flow.
Once all three loops stop sensors, all outputs are necessarily true, then the case and a compound bow structure in the loop (reset) next is useless. Because the boolean in the fourth loop ending is immediately true, the loop to stop and not care about the State of the reset button. Maybe you should connect the termination condition to the wire going to the system reset light instead. Since it is also a polling loop, it needs a small wait. Once you press reset, the VI full and stops. (Do not use the continuous operation mode!).
Solution: Create a state machine with a single outer loop. You have 4 x code too!
-
connected successfullyError: number of columns does not match number of values in line 1
Hi guys
I'm new to php so its probably a stupid mistake. Anyone know why I get this error?
define ('DB_NAME', ");
define ('DB_USER', ");
define ('DB_PASSWORD', ");
define ('DB_HOST', ");
define ('DB_TABLE', 'Membership');
$link = mysql_connect (DB_HOST, DB_USER, DB_PASSWORD, DB_TABLE);
If (! $link) {}
Die ("could not connect: '.") mysql_error());
}
$db_selected = @mysql_select_db (DB_NAME, $link);
If (! $db_selected) {}
Die ('can\ 't use'.) DB_NAME. ': ' . mysql_error());
}
$value1 = $_POST ['Membershiptype"];
$value2 = $_POST ['BCUMemberType'];
$value3 = $_POST ['full Name'];
$value4 = $_POST ['D.O.B '];
$value5 = $_POST ["sex"];
$value6 = $_POST ["PhoneNumber"];
$value7 = $_POST ["EmailAddress"];
$value8 = $_POST ['BCUNumber'];
$value9 = $_POST ['BCUMember'];
$value10 = $_POST ['address'];
$value11 = $_POST ['city'];
$value12 = $_POST ['city'];
$value13 = $_POST ['postal code'];
$value14 = $_POST ['disabled'];
$value15 = $_POST ['MedicalInformation"];
$value16 = $_POST ["photography"];
$value17 = $_POST ["ContactName"];
$value18 = $_POST ['link'];
$value19 = $_POST ['ContactPhoneNumber'];
echo 'connected successfully ';
$sql = "INSERT INTO membership (Membershiptype, BCUMemberType, FullName, date of birth, gender, phone number, EmailAddress, BCUNumber, BCUMember, StreetAddress, city, city, postal code, disability, MedicalInformation, photography, ContactName, relationship, ContactPhoneNumber) VALUES (' $value1, $value2, $value3, $value4, $value5, $value6, $value7, $value8, $value9, $value10, $value11, $value12, $value13, $value14, $value15, $value16, $value17, $value18, $value19");
If (! mysql_query ($sql)) {}
Die (' error: '. mysql_error());
}
mysql_close();
? >
I deleted the login information for obvious reasons.
Any help would be appreciated.
Thank you
Bradley
> However I now have and error: Unknown column 'Date of birth' in
> "The field list. Is it due to the "." at the birth date in the database?
No doubt. You could probably quote the name of column to correct this, but it is best to always avoid special characters in column names. I would like to change to DOB, or better yet, DateOfBirth.
-
Size of the hard drive does not match, what to do?
End of 2012, the MacBook Pro 13 "
I've added everything I installed and registered on my macbook and it does not match the size of my disk info...
I just deleted all the documents that I need to see what will happen with the size of the disk and it says: drive for 'other' size is 85GB andAudio = 0
Film = 0
Photo = 0
Programs = 0
Security Copies = 0
Other = 85,17 GBAnd the strange thing is that I have 10 + adobe programs installed (that doesn't add anywhere near 85 GB!)
But the weird thing ', it is also that it shows 0GB to programs/software that I obviously have a lot of programs/software installed. WHAAAT...It's really annoying
It seems as if increases the amount of data in 'other' counts for
Is there someone out there in the world of the internet, who knows how to fix this?
I tried to read a previous debate about this, but to be honest, I do not understand...
I'm not exactly a macbook-computer-expert when it comes to knowledge like thatI would be grateful for your help!
It is in Danish, but... Yes
LYD Sound/Audio =
Film = film
Photo = Photo
Progr. = Programs
Sik.Kopier = security Copies
Agent = other -
Elapsed time on graph does not match indicator sound
Hello
I created a vi that displays three waveforms on a graph whose axis x shows the time elapsed since the vi was launched. The data is written to an excel spreadsheet. Everything works as expected with the exception that column of time in my file does not match the time that is displayed on the x-axis of my table. The time in my file only shows increments of 0.1 second, with the same sample for every ten samples, so that the time on the graph increases in increments of 0.001 (accuracy I had put in) and is unique for each data point in amplitude. I have attached my output file for reference. The column 'X' is both.
I am collecting data at 100 Hz and 10 samples of reading both using the continuous sampling mode. Without my loop for the values of x, I get a sample of time on every ten - what I understand why, given my sampling rate; with it, I get this same sample for all ten samples (again, I think I understand why, but foolishly hoped that might solve the problem). What I don't understand is why the time on my table is incrementing differently time data, I wrote to my folder, since both are from the same source. Anyone would be able to help me understand that, if I can try to solve my problem?
I have also included my vi. I use USB 6229 OEM.
This is because you write 10 copies of t0 to the worksheet
Try this little maodification and see if that helps
-
Harger W530 AC does not match the Jack of the portable power
I just got my new W530, but I can't load it. Looks like 170W AC/DC charger is just, but somehow the physical connector does not match the power supply of the portable computer. Charger AC/DC 170W is not circular but with two small rectangles, however W530 is completely circular. Someone had the same problem? I try to return W530 that looks like it was made of bad sense but takes to always come back. any recommendations? Technical service told me since it is within 21 days after the delivery, I better return.
Technical service is great
But after the sale to get back really really bad!
It's quad-core, it requires 170W "brick" AC load, which has one taken not circular.
-
unlock code does not match system
get the message "unlock code does not match system" whenever I try to open my game.can someone help me "
Hello catou212,
You need locate the manufacturer of the game in question and contact the Helpdesk of the manufacturer directly to get the correct unlock code.
Hope this helps
Chris.H
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
Hi there... How can I sort this problem as this message looks back constantly on google Account... ERROR POSSIBLE WITH GWT. The value of time compilation agent MODULE XML FILE user (ie6) does not match the value of user.agent (ie8) run time
Hello nEve Adam,.
Thanks for the return of the response. Below, I've added some links Google support on this issue. I hope this helps.
ERROR: Problem Possible with your *. GWT.XML file module. The value of compile time user.agent (opera) does not match
http://www.Google.com/support/forum/p/blogger/thread?TID=2d6d9bd1326a07c4&hl=en
In addition,
Message from Web page
-
Toshiba satellite running Vista. The file is possibly corrupted. The file header checksum does not match the checksum calculated. Tried all posisible boots and no joy, continues to turn it back on! Frustration...
Hey James,.
I does no change, I didn't download a document from my email (from a sender of confidence). I tried to start in safe mode, just, it restarts and goes back to the corrupted checksum display... Last known good config was the same result! The only error message is one that is in the title of this post, not others. Another detail, that I forgot to add is that it does not get insofar as a logo windows before it fails, just the toshiba start screen, then either passes the corrupt message checksum or a blue screen and restarts before I can read the text on the blue screen. Thanks for your response! Any additional help would be excellent if you can. In the meantime, I'll try your methods. Thanks againOK, I have now managed a Startup Repair trying over and over again. Restore all settings and now looks very good, thanks for your help! -
trying to get a simple answer to my question, I asked the support of microsoft for the contact to ask someone who knows about flight simulator but I can't spend the screen requests I have enter product code - I walked into the box of the product id provided key interest which enabled but said stupid site simply enter the code in the indicated format and it does not match this format once again , I can't communicate with them-i suspect that it is a ploy because there is no available support and it's a time of great runaround.last they do not recognize my computer id code - this time, they have recognized my computer but then obscured code fsx - i don't believe that someone will read this-i has recently received a message to say that my thread on an unanswered question them earlier had been removed and I was wondering who decides that - always has to be someone in life at microsoft
Hello
Where have you bought Microsoft Flight Simulator X for?
Follow the steps in this article.
Solving the problems of activation for Microsoft games and mapping programshttp://support.Microsoft.com/kb/960480
Also see this article:
How to get a new product key for Microsoft Games for Windows, Streets & Trips, or MapPoint
http://support.Microsoft.com/kb/973457If the problem persists, Flight Simulator supports for assistance.
http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspxKind regards
Afzal Taher
Microsoft technical support engineer -
total size of the files of Windows 7 does not match the size of partition
In the D: partition
total space: 265 GB free space: 59.1 GB
There is only one visible folder: Daisy, size: 87.4 GB from the Explorer
Other records hidden three: info Volume system, c:\Windows\Msdownld.tmp, $RECYCLE. BIN takes up almost no space
Of course free space does not match the file size.
Do not partition system, no problem to update windows and restoration, sleep or page file.
Some strange things:
1. with the help of file size 3.4 correctly see the size of the file
Daisy file occupies 206GB
Once I copied the whole file to the other partition Daisy
and the result is the record more like 2xxGB
so I guess that 206GB is the right size
/////////////////////////////////
may be ignored.
2 folder being read-only Daisy
Even uncheck or untick read only box in the properties of the folder does no effect
After loading, it still shows read only
3. 'read only' does not work
2, daisy file is read only
but I managed to delete files inside
////////////////////////////////
////////////////////////////////
Is it a mistake to folder structure?
It's a newly installed windows, so I guess that windows is clean
Hope to see the solution and identify the problem
Thank you very much
OK, based on your new information, the error is that Daisy is 206 GB but Windows Explorer reports it as 87GB.
No other information seems more relevant.
Ideas-
1 run ChkDsk on the drive - [first of all, make sure you have a backup of Daisy or make a new backup always] in Windows Explorer, right-click on the drive & select Properties, then the Tools tab, then click the check now button, turn off the option to make repairs in first to see if there are errors or not before making any decision as repairs can delete or corrupt files which are reported in the file allocation table.
2. find another utility that measures the size of record to help you track down all the difference here. TreeSize Free will be repeated.
I do not understand your comment "later, I found the reason why I can't locate the"office"is the language of auto change." It's in Chinese at first but watch the 'bureau' cmd"that this had not been mentioned before.
Denis
-
500 the application author does not match the author token of debugging
My name is Jean-François Geyelin. My application name is PewPew.
When you try to run PewPew on a playbook, I get the error "500 the Application author does not match debug token author.":
the command deploy blackberry - installApp-password abdelkader 192.168.1.37 - package device-Debug/PewPew.bar returns:
Info: Send request: install
Info: Action: install
Info: File size: 3575023
Info: installation...
Info: Treatment 3575023 bytes
actual_dname:
actual_id:
actual_version:
result::failure 500 the Application author does not match debug author token.I did check the following:
the blackberry-nativepackager - listManifest PewPew.bar command returns (among others):
Package-author: Jean-Francois Geyelin
Package-author-Id: gYAAgPqb4i9DBQ-DjR0zWsAWK8s
blackberry nativepackager - listManifest library/Research\ In\ Motion control / debugtoken1.bar returns (among others):
Package-author: Jean-Francois Geyelin
Package-author-Id: gYAAgPqb4i9DBQ-DjR0zWsAWK8sWhat should I check or what is the problem?
Problem solved by clearing and forwarding of the token of the device debugging.
-
paper detected does not match the paper size
After clearing a paper jam when I go to print the 7310 all in one, beeps and has "paper detected does not match size of paper or type". When I hit OK the printed page is slightly bias. How can I fix it?
First thing I want you to try is cleaning the rollers. You said that the printed pages were asymmetrical. Which can be the cause of the printer read the incorrect paper size and give this message. The document below the link should help you clear up the problem of tilt. Let me know what happens.
Maybe you are looking for
-
Hello whenever I open my firefox, the parameters can change. Specifically, the start page: it starts where I did, even if I don't want. I want google as my home page, and continues to change that. I have already updated to the latest version, but the
-
History disappears and list drop-down lists/options in 10.0.2
I have Windows 7 and recently installed Firefox, because I love to explore. I am running 10.0.2. When I click on any item to the taskbar, the drop down menu appear and disappear when I try to choose an option. The same thing happens when sites sugges
-
printer does not work it tells me not connected to the internet
my printer just stopped working.it says it is not connected to the internet.it was before.
-
Failed verification of password of HP Mini 1000... need code to open a session
I have a helping hand me down HP mini 1000 and I get the following Password check failed Fatal error... System stopped CNU9243KDB can someone help me get it up and running again? Thank you Eric
-
report of suspicious calls "Microsoft."
At 11:16 (PST) today our telephone office and phone rang a few seconds apart. I answered the office phone, my wife answered the phone at home. A man who sounded like it was said in India with Windows Office customer and was called because my computer