Create the circuit of the STS - V between 2 15454 SONET with CE100T
Hi all
I have a problem that I can't find documentation for.
I create an ethernet point to point circuit between 2 15454 SONET with CLC ver 8.5 knots. The circuit will carry you a VLAN not routed between switches, Cisco 4948 in 2 data centers. I use CE100T-8 cards which the ethernet 100/full value, checked the Frother. The POS is configured with a GFP - F frame and 32-bit CRC. Type of circuit is a single STS - V STS to 50Mbit of bandwidth.
The switch ports are configured as access ports on the VIRTUAL LAN set to 100/full. At the end of B, the connection between the switch and the port of THIS is a straight through cable. End is a crossover. switch ports are configured as such:
switchport access vlan 512
switchport mode access
switchport nonegotiate
Speed 100
full duplex
Problem I have is that end A "Transport Layer failure" alarm to end and end B has the 'Carrier loss on the LAN' alarm near end. No end shows an ethernet connection
Wiring has been tested, I've tried other ports on the CE and have deleted and recreated the circuit board.
What simple step/setting I'm missing?
Thank you in advance,
Jim Bowen
Jim,
It seems that your problem is by your side B that has the loss of carrier on the LAN. The failure of Transport layer will be on the end node in these cases.
You mentioned that the end B is a straight through cable from the switch to the CE card but the side is cross. The first thing you can try is to put a cable on the side B as well because it looks like the side of A working very well (doesn't have the loss of carrier on LAN).
I don't remember if cards of IT have an option to hardcode the speed and duplex but if they can only so if the suggestion of cable does not work. If this does not work, you can try setting autonegotiation on switch and the map of THIS to see if it solves your problem. Once the loss of the carrier and LAN to clear alarm you should be up and running.
Also, I can't remember if the EC supports the loopback test, but if you can try try to put a Terminal loop on the B side (it's optical to) your end should appear and your switch should appear/maximum looping. I would like to know how things work out for you. Looks like you're almost there a few tweaks should get running.
Thank you.
Ryan
Tags: Cisco Network
Similar Questions
-
How to create the BC4J Package in JDev 10 g (with OAF)?
How to create the BC4J Package in JDev 10 g (with OAF)?
I use JDev 10.1.3.3.0 with Extension OA release 12.0.6. Right-click on the project of the new option Business Package of components is missing, I tried the business components of the Tables option but could not continiue as steps in the tutorial have does not match this wizard individual. I read on this forum that you can use this option to create the EOs and your and then specify packages later.
Any help will be appreciated. The tutorial that I'm following is the Oracle Application Framework (tutorials) the JDevDoc\Index.html Toolbox
Thank you
VijayHello
Tutorial is not being updated, Jdeveloper 10 g, there is no need to create the BC4j package explicitly, you just create AM OT or VO and mention the name of package, JDeveloper will take care rest of things, create new your EOs
Right-click on the project--> New--> business components ADF (under the enterprise level)---> Module object/Application/view of object entity.
Thank you
Pratap -
Create the directory of procedure to aid directory with path parameter name
Hello
I've written a procedure that takes name (C:\temp) to a directory as a parameter and creates the directory oracle using EXECUTE IMMEDIATE of the procedure. Proc compiled fine but when I try to run it (exec prc_lx_e_m_fund_activty ("C:\interface','test1.txt','20040102"), I get the following error with the execute immediate statement below.
create or replace
PROCEDURE prc_lx_e_m_fund_activty
(
i_output_dir IN VARCHAR2,
i_output_file_name IN VARCHAR2,
i_interface_date in VARCHAR2
)
AS
.
.
.
.
RUN IMMEDIATELY 'CREATE OR REPLACE DIRECTORY OUTPUT_PATH AS | ''''|| i_output_dir | " ' || « ; » ; -Where i_output_dir = C:\temp (I'm passing this parameter as IN)
.
.
.
END
ORA-01481: invalid number format model
ORA-06512: at "DBO." " PRC_LX_E_M_FUND_ACTIVTY', line 326
ORA-00911: invalid character
ORA-06512: at line 10
Process is complete.
Kind regards
Mason.Try this
SQL> ed Wrote file afiedt.buf 1 create or replace 2 PROCEDURE prc_lx_e_m_fund_activty 3 ( 4 i_output_dir IN VARCHAR2, 5 i_output_file_name IN VARCHAR2, 6 i_interface_date IN VARCHAR2 7 ) 8 AS 9 begin 10 EXECUTE IMMEDIATE 'CREATE OR REPLACE DIRECTORY OUTPUT_PATH AS '|| i_output_dir ; 11* END; 12 / Procedure created. SQL> exec prc_lx_e_m_fund_activty('''c:\temp''','aa','bb'); PL/SQL procedure successfully completed. SQL> SQL> SET LINES 10000 SQL> SELECT * FROM ALL_DIRECTORIES; OWNER DIRECTORY_NAME DIRECTORY_PATH ------------------------------ ------------------------------ ---------------------- SYS OUTPUT_PATH c:\temp
-
How to create the shared disk between 2 ESXi servers
Hello
I created a laboratory with ESXi4.1 and ESXi5.0 machines with a few virtual machines on them on my laptop using vmware workstation 7. Now, I'm trying to add a disk to the two virtual esx hosts so that I can create a store of data through them to do some testing from day to day, but so far I managed to do it. I'm afraid of how would I have accomplished my test laboratory. Can someone help me on this please. Thank you.
Kind regards
AB
beckham007fifa wrote:
I created a laboratory with ESXi4.1 and ESXi5.0 machines with a few virtual machines on them on my laptop using vmware workstation 7.
You cannot use just a shared between two virtual hosts of ESXi, but put up some "fake" your iSCSI storage, shared disk which could be executed in another VM on your VMware workstation. Here is a guide how to set this using the free Openfiler: http://rickardnobel.se/archives/26
-
How to create the database link between the production and the test server
You will need to create a link between Test and prod DB access. We need only select access from user@prod to user1@test.
Could someone please answer for example?
Thank you
sRIIYou will need to create a link between Test and prod DB access. We need only select access from user@prod to user1@test.
Could someone please answer for example?
If test for prod
create public database link to_prod connect to the user identified by password using 'to_prod ';
Check that to_prod is directed to your production database.
-
Create the new database without PDB or without using C#.
Dear all
I am able to create the database table in oracle 12 c with prefix c#, while I want to create without prefix. I read all the documents, but still, I don't understand. can anyone explain that
I use the following command to create the database
create the c ##test user identified by test;
Grant connect, resources to c ##test;
grant imp_full_database c ##test;
grant permission to c ##test;
Sandy
Oracle-DBA-Sundar says:
Hello
Alter system set COMMON_USER_PREFIX==''
create user test123 identified by test123;
Above may work
Thank you
Sundar
Sometimes I wish we could downvote or dislike some of the answers.
Even when it works, it is not correct to do so. The problem was how to distinguish between normal users in a PDB file and common users. I guess that the original poster must simply learn to switch / connect on a preliminary draft budget, where it can create users just like it was before. And the cause, it must first of all a PDB file.
Instead he will now create common users and use these users just as local, thus throwing the whole concept shared in the drain.
The user command to create now has an additional parameter 'container '. I use in scripts to prevent the execution of a script in the bad environment (CBD/PDB).
In a CBD, this will create a common user. The default container clause is ALL here.
create user mycomm identified by mycomm container=all;
This creates a local user in a PDB file. The default container clause CURRENT here.
SELECT NAME, OPEN_MODE, RESTRICTED, OPEN_TIME FROM V$PDBS; alter session set container = PDB1 create user mylocal identified by mylocal container=current;
BTW. I don't see a major issue to create ordinary users without the c# # prefix, as long as you know exactly what you are doing. I see the prefix C# as a safety mechanism, preventing you from accidentally creating common users with identical names as local users.
Pete Finnigan did some research on how to create different types of users in an environment of 12 c: http://www.petefinnigan.com/weblog/archives/00001370.htm
-
"Can't find the necessary files" cannot retrieve or create the recovery disk. Help!
I can't refresh PC or create the recovery disk. He keeps going with error message "Cannot find the necessary files" and tells me to insert the recovery media. There is no system restore point, and I've upgraded to Windows 7 Windows 8 Pro without a disc, so I can't do anything. Help! Strangely, nusrmgr.cpl disappeared, although I had seen the shortcut a few weeks ago (no, I'm not deleting it).
Hello
I imagine the inconvenience that you are experiencing. I'll certainly try and help you in the matter of fixing.
To help you to propose measures to solve the problem, I would appreciate if you could answer the following questions:
1. Why are you trying to cool off the computer?
2 are you facing problems with Windows 8?
3. how many accounts is configured in the computer?
You can scan the file system (CFS) auditor. This will replace the corrupted Windows files.
Follow these steps:
(a) start the desktop view.
(b) open the command prompt, right-click in the left corner when the windowappears, and select prompt (admin).
(c) type the following command and press ENTER:
sfc/scannow
The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.
You can also try to create a new user account and check if the problem persists.
If the problem persists, you will need the DVD to perform repair installation of Windows 8. If you download the installation of Windows 8 files, check your emails, there should be a link to download an ISO file. Download and burn the file to a DVD.
The DVD to perform the repair.
Hope this information was helpful and let us know if you need more assistance. We will be happy to help you.
-
How to create the "clear key" for the control panel simple search
Hello
I have a QueryRN with mode of construction research = none.
I would like to add a button 'Clear' on the search panel simple I know is there any settings / need to create the clear key caraa?
Please share with me the method to create the clear key... Thanks :)
pls help...Hello
Use below a
OAMessageLovInputBean LovBean = (OAMessageLovInputBean)webBean.findIndexedChildRecursive("Item"); if(LovBean!=null) { LovBean.setValue(pageContext,null); }
Kind regards
GYAN -
I want to create the link (to each row) in my detail page < < < < < in order, the articulation between (detail page 1 < < < detail 2).
Hello
f9afc1ea-f5a4-4400-A33A-187e03664d82 wrote:
I want to create the link (to each row) in my detail page< in="" order="" to="" linking="" between="" (detail="" page="" 1="">< detail="">
Change your column on which you want to create the link
go to declare attributes-> column change-> under the column link
1. Select a text link (you have option available under the link text select one of these option)
2 target - > application Page
3 page-> page not on which you want to redirect
If you want to pass a value then
Item1-> select an item in the page detail2
values-> that you want to move the page pos.1
see this screen shot for reference
Hope this helps you,
Kind regards
Jitendra
-
When I create two keyframes at the same position between keyframes at different positions this way adds a loop. How can I get rid of the loop? I was just by dragging the handles on the vertex point, but I want to get rid of the loop together.
Focus on the Bezier handles on the motion path in the Composition window. You can select the tool pen (g) and hold down the Alt/Option key to select the tool convert Vertex (it looks like a V on the side) and then fix the handle manually or click on the top of the trajectory to change it to a straight line. You can also play with spatial interpretation Keyframe.
To avoid this, you can change the interpolation of keyframes in space to linear preferences. Most of the time I don't like straight so I keep my default value of Bézier.
-
The report generator (impossible to create the join between the 2 groups)
I have 2 queries and want to create different gourp and want to join these groups with the butts of lint data impossible to create the join between groups please guide me how can I do it.
Thanks in advance
Query1 and goup 1.
SELECT
TO_NUMBER (STUDENT_ROLL_NUMBER) STUDENT_ROLL_NUMBER,
ACIVITY_STATUS AS ACIVITY_STATUS_ADM,
CREATION_DATE DATE_ADM,
(SELECT BILL_CLASS_FEE_STRUCTURE, BILL_CLASS CLASS_NAME CLASS WHERE FRESH.) CLASS_ID = CLASS. CLASS_ID AND FEE_STRUCTURE_ID = ADM_FEE_STRUCTURE_ID) ADM_FEE_STRUCTURE_ID;
(SELECT DESCRIPTION OF BR BRANCH_NETWORK_REGION_LINK WHERE BRANCH = BRANCH_ID) ADM_SOURCE_BRANCH_ID,
(SELECT R_DESCRIPTION FROM BR BRANCH_NETWORK_REGION_LINK WHERE BRANCH = BRANCH_ID) ADM_REGION, '1' AS NO.
Of
SMA ADM_CHALLAN_HIST
WHERE
STUDENT_ROLL_NUMBER =: STUDENT_ROLL_NUMBER
Querry 2 and group 2:
SELECT
-PROMOTION_HIST_ID,
PR. ACIVITY_STATUS PRO_ACIVITY_STATUS,
BOX WHEN PR. STUDENT_STATUS = 'Y', THEN 'ACTIVE' END PRO_STUDENT_STATUS.
TO_NUMBER (PR. STUDENT_ROLL_NUMBER STUDENT_ROLL_NUMBER).
(SELECT BILL_CLASS_FEE_STRUCTURE, BILL_CLASS CLASS_NAME CLASS WHERE FRESH.) CLASS_ID = CLASS. CLASS_ID AND FEE_STRUCTURE_ID = SOURCE_FEE_STRUCTURE_ID) SOURCE_PROMOTION_CLASS;
(SELECT BILL_CLASS_FEE_STRUCTURE, BILL_CLASS CLASS_NAME CLASS WHERE FRESH.) CLASS_ID = CLASS. CLASS_ID AND FEE_STRUCTURE_ID = DEST_FEE_STRUCTURE_ID) DEST_PROMOTION_CLASS;
(SELECT DESCRIPTION OF BR BRANCH_NETWORK_REGION_LINK WHERE BRANCH = SOURCE_BRANCH_ID) SOURCE_PRO_BRANCH_ID,
(SELECT DESCRIPTION OF BR BRANCH_NETWORK_REGION_LINK WHERE BRANCH = DEST_BRANCH_ID) DEST_PRO_BRANCH_ID,
(SELECT SESSIONNAME BILL_SESSION WHERE SESSION_ID = S_SESSION_ID) SOURCE_PRO_SESSION_ID,
(SELECT SESSIONNAME BILL_SESSION WHERE SESSION_ID = D_SESSION_ID) DESTINATION_PRO_SESSION_ID,
D_SECTION PRO_SETION,
CREATION_DATE PRO_DATE,
'2' AS NO.
Of
STUDENT_PROMOTION_HIST PR
WHERE
STUDENT_ROLL_NUMBER =: STUDENT_ROLL_NUMBERwith a click on the link tool palette
Click the field on the master, and then drag the field to the slave
If you want more fields in the link, then repeat for each field of the previous operation -
Problem to create the Internet connection sharing between Windows XP and Windows Vista.
Original title: Internet connection sharing between Windows XP and Windows Vista.
Hello
Recently, I plugged a laptop running Windows XP to a desktop computer running Windows Vista using a standard Ethernet cable with the intention of use sharing of Internet connection. The notebook contains a wireless connection that I've routed to the office via the cable said. While the initial phase of installation went well (I was too lazy to do it manually, so I just used the Wizard "Set up a home or small business network" Windows XP,) I had to turn off the host computer to install a program. When I tried to set up ICS again, I couldn't connect to the Internet by using ICS. After this failure, I tried to configure the properties of TC/IPv4 (IP, gateway by default, etc.) manually, but I still couldn't run. I am able to access the shared host PC and client files. It seems to me that some service essential to the proper functioning of the ICS may be disabled in some way, but it's just speculation, as I have no evidence of such a service. Help would be most appreciated.
Thank you
FG-man
I tried this before using a laptop to share internet with my 360. problem is there was Nat on the router, and it is in contradiction with the ics.
Anyway long story short I did some research on the Internet and discovered that if you're behind a router ICS will be confllict with her, as ICS also does routing. a much better option is to "bridge the conections ' on the laptop.
If you go this route, you need to set a static ip address for the office,
Either that or if you want to continue using ICS put the laptop in the DMZ in the router may help, but it will be less secure.
Hope that this helped good luck
-
Satellite P100-429, stopped after you create the partition on the HARD disk
After you create the partition on the HARD disk. PC just stopped.
After using the restore CD, nothing happened again, any ideas?Hello
Express media player has been installed on the partition of the laptop?
I can give you a good solution for 100%, but there may be a conflict between the express media player partition and the new partition.
Have you installed the OS on the new partition?Hey Buddy, try to delete the entire partitions in the HARD drive and format the HARD drive completely. Then try to use it again the Toshiba Recovery CD and install Toshiba image on the HARD drive.
-
Satellite A100-906: Express Media Player does not create the c partition
I recently bought the Satellite A100-906 model and I would like to make a partition to save the data, but the already existing partition with the reader of the Express does not allow part C: partitioning.
If I delete the partition Express I'll be able to install it after I divide the part C: or I have to choose between separation and the Media Player?
In my opinion it should work, but you must create the Express Media Player partition with the same size as the old.
PS: Do you know the Partitions Magic 8? This software allows you to create partitions while Windows is running. It's a great tool
-
Problem with the published parameters between the movement of FCPX
Hello
I have a little problem with the settings published between the movement at FCPX.
For some reason, the published parameters have different values within FCPX in movement.
For example, in motion, a parameter is - 187.04 and in FCPX is-0,19. What are the parameters of position for CSOS.
If I try to change this setting in FCPX, the application crashes after 10 seconds or less.
No idea what is causing the problem? I re-edited the effect several times, same result. The software that I use is FCPX 10.2.2 and 10.2 of the Motion.
MOTION
FINAL CUT X
Thank you.
The values that you have published on the move have been compared to this project that you created. The values shown in FCPX are "consistent" with any project that you create. Often, you will see the center screen is 0.5, 0.5. Left and below are 0, right and up are 1.0. Or you could see Center of 0.0 and a range between - 0.5 and 0.5. Sometimes, you will see the numbers on the scale of some sort of percentage (vertical values will be 0-100 [%] and the horizontal will be based on the aspect of the project, for example, horizontal will be between 0 and 177.7778 for a project of 1920 x 1080, etc..) It will depend on the type of object and the parameters associated with what you posted.
If you want to "correct" values in FCPX, you will probably need to rig settings, otherwise, just live with it.
For what is * why * your model crashes FCPX, that will be another reason and not the difference in the numbers. So, can we get more information on the model?
To use specific fonts?
You publish alterations settings?
Anything out of the ordinary?
Maybe you are looking for
-
How can I move my bookmarks, etc. from my old mac to my new mac?
I recently bought a new Mac Book Pro. How to import my data from Firefox (bookmarks, etc.) to my new laptop. Thank you Jay
-
Toshiba Camileo P30 - load problems
Hello everyone, Yesterday, I bought a camcorder Camileo P30, I left him in charge all night, the light was still on (not flashing), then in the morning, I tried to use the camera but was still not loaded!So I left all day on the load (I'm at work) an
-
THE HP 1315 PCS CD - INSTALLATION PROBLEM
MY COMPUTER OS: WINDOWS XP MY PRINTER: PRINTER HP PSC 1315, COPY AND SCAN, with original HP CD. (Printer out of warranty) I am, of 73 year having no technical Assistance ([personal information deleted]) Because of some virus, the computer is reformat
-
I want to remove the 2 profiles that divides my laptop. I wish well for my laptop one without loseing computer programs that have been added. My laptop is a Dell Inspiron 2650 Oh
-
After upgrade blackBerry smartphones - can not use headphones! Only the speaker!
After the upgrade to the new operating system, I can't use the headset. I hear nothing and no one can hear me speak. When I change to speaker that works - but who wants to go through life with everyone heard your calls! This phone is essential for