destroy a table

Similar Questions

• Predator G9 15 - 591 - 70VM Intel rapid storage technology

  Hi guys

  So I used the Intel RST in my mobile predator that I bought for almost 2 months, created a RAID 1 Volume using the SSD and HARD drive. But without treading of the understanding that the RAID1 'had to be done with 2 drives of the same capacity to avoid wasting space'. For now, I see only my SSD in my OS, but the HARD drive is still present in the software of the RST as a recovery disk. So I would like to cancel my RAID1, that I found is possible, but I couldn't use the CTRL + i or other ways to open the option of RST No. ROM POST. What should I do?

  NEED HELP!

  BTW, I asked at the disk of dissappearing in the Intel community, a guy told me but now I want to find a way to cancel my first RAID1.

  Switch back to RAID without re-creating the table, it's just a degraded RAID array and leaving as AHCI is the best solution, the only thing you will need to set AHCI is to change the configuration of the disk 10 windows or you will experience a BSOD.

  http://www.tenforums.com/drivers-hardware/15006-Attn-SSD-owners-enabling-AHCI-mode-after-Windows-10-...

  here refers a change in the IDE to AHCI, but it's the same RAID on AHCI.

  One thing we address here is storing the value RAID controller in the BIOS, crossing the AHCI simply destroy the table and it's the fastest way to do and you don't even need to format the other drive with Gparted, but you can do it from windows itself if... RAID is 1.

  so...

  Only on the RAID1 configurations:

  1. run as administrator command prompt (logo key windows + x - click prompt (Admin))
  2 call a boot safe mode with the command: bcdedit/set {current} minimum safeboot
  3. restart the PC and enter your BIOS during the startup.
  4. change of RAID in AHCI mode and then save & exit (F10).
  5 Windows 10 will run in Mode safe, once started, remember that C: is your SSD and not the HARD drive.

  (if it gives an error 'no boot device', you need to check the BIOS if the windows Boot Manager is the first boot device.)
  6. do a right-click the icon of the window and choose to run the command prompt (Admin)

  7. then inside the cmd window, type
  DiskPart
  then, type diskpart
  list disk
  take note of the correct disc ID to clear
  Select disk x
  (where x is the ID of your disk to erase)
  clean
  output
  your HARD drive will be erased completely

  8. then open a command prompt (admin), once again and Safe Mode cancel startup with the command: bcdedit /deletevalue {current} safeboot
  9 reboot your PC once more and this time that it will start normally, but with AHCI mode enabled.

• PERC 6 / i of the RAID1 to RAID10 switching?

  I am running PowerEdge R610 with two 146 GB drives in a RAID1 configuration, with Debian as operating system. I am considering the expansion of total capacity with two extra drives, as the free space becomes low. I can afford some interruptions in service, if necessary.

  My question is: can I easily add more than two disks and move to RAID10 the fly to increase the total capacity without any loss of data? If so, how would I go to do? Or should I do a full backup, destroy the table, create and restore data afterwards?

  Hello

  You are not able to reconfigure a table split. Depending on your controller, you may be able to reconfigure a RAID 5 or 6. http://www.Dell.com/support/article/us/en/04/SLN156113/en

• Remove the extra space of a long document

  Hello

  I've seen a number of find/replace and GREP formulas to do similar things. I have NO scripting language or coding experience and have worked to understand GREP.

  So I'm a little afraid to use it because I don't know what all the modifiers call (I have a few neat GREP cheatsheets print as Mike Witherell I can absorb up to get a good reference)

  I need something I can copy and paste into find/replace or dialog GREP that will do the following in less than 12 steps (we hope) without doing something as catastrophic as the removal of all my paragraph marks (which I almost did with someones GREP expression)

  1. No space before a comma, period, exclamation point, question mark, colon, semicolon
  2. A space only after any of these
  3. A space before an opening parenthesis and a space after the closing parenthesis
  4. No space before the closing parenthesis or after the opening parenthesis
  5. Remove double or extra spaces (en, em, etc.)
  6. Remove comma before parentheses
  7. Remove all white space after a paragraph mark

  I think that's it

  I found this one recently (perhaps Jongware?)

  [~ m ~ > ~ f ~ | ~ S ~ s < ~/~,~3~4%] {2.

  From my limited understanding addresses em, in, flush and hair, space nonbreaking, space figure, third space - not sure of the rest. It's really way over my head.

  I know it will be a piece of cake for you guys

  Thank you

  I was hoping Jongware would come in with something really elegant (and maybe he'll still) but in the meantime, my approach would be to start by eliminating all multiple spaces except paragraph returns and forced line breaks. This appears to do:

  Find (\s)(\p{space_separator}|\t) + and replace it with $1

  This leaves the first space and will remove the following spaces to a line or a paragraph break (and not completely tested, but I guess that other kinds of breaks) is encountered, leaving the jump line or paragraph intact.  Note that this will destroy the tables built with tabs (as opposed to the 'real' tables) with several tabs between the items, and it does not alter a single space before a line or paragraph break.

  Then I would remove the whitesapce at the ends of paragraphs, etc.:

  Find (\s)(\n|\r) and repace with $2 seems to do, and it also seems to leave several returns (I don't know if you want to delete these) and work with the other breaks as well (again, not fully tested). The \s$ and replace it with nothing more simple, removes the first return to a sequence of two-back and seems to ignore e other types of breaks completely.

  At this stage avoid any several spaces other than possibly empty paragraphs. If you want to get rid of these, you can run find/replace list script by the integrated switchis refers to the single request of return in the dropdown, find/replace.

  So now you find the opening of single and double parentheses, square brackets or braces quotes and remove space after them, if it exists:

  Find ([\[\{\(~{~[])(\s) and replace it with $1

  and finally to remove any white space before your selected punctuation and the closure of the above case:

  Find (\s)([.,;:!\)\]\}~}~]]) and replace it with $2

  The last two queries will probably also work with look-bhind for the first and to come to the second (putting classes in the expressions of the eyes) and repalcing with nothing, but I don't know which method is the most effective. The last request might also be missing a space and an apostrophe or mistakenly remove a space before a work that begins with an apostophe (again, not tested). and is ignoring straigh citations of any type, because they are ambdextrous and may want to space on each side.

  I hope that the forum does not spoil one of these phrases...

• Table of contents completely destroyed export

  Hello

  a COT of person never turned out like this when you export to PDF?

  Thank you!

  Well you do not have a tab stop, so it seems

  I've seen it before where the tabs look like (see below) and it has messed up the page layout when exporting to PDF format.

  

  Tab stop exactly where the first line indent is.

• Read xls file and display the data in the table.

  Hello

  Try to read the data from an xls or csv file and fill the same data in the table. If I need to use the table to store the data from the file and display, hoping that someone could help.

  Thank you

  Hari

  Hi hari,.

  One thing that is very important when you use the Excel activeX interface (in case you need it) is good termination of worksheet/workbook/lettering handles.

  You need these handles to specify what cell in which file you are trying to access.

  If you are unable to throw each handle you have, then you will be left with ghost Excel process in your task manager, devours your system's memory.

  Thus, when debugging of your application, open the Task Manager and the watch as Excel treats created/destroyed and make sure that you end up with zero Excel process running when your application is closed.

  Also consider the case of fault for your program. Check that your exit routes did not omit any termination of handle.

• How sting/view images in memory without having to build the massive tables?

  I wrote a program that will capture up to 100 images, total of 500 MB.  I queue to each image (table 1 d of 12 bit) in a table of queues.  I would like to 'see' queues selectively capture data (but not destroy each queue) and display this data as a large stitched image.

  I was able to do this by building a table of each queue and manipulate rows/columns until the images are stitched in my model.  Does that create an another 500MB of memory lost since I 'copy' the queue data in another table?

  Also, is there an easier way to do this?

  Hey dre99gsx,

  IV wrote an example that seems to be the most progressive option in the construction of a large image to present its restriction to the use of grayscale (U8) and only built a training table 1 d.

  It is a requirement that you can access the separate images after that that they were sewn.

  Hope this helps

  Philippe

• How to create the constructor function for a pl/sql table?

  I created a PL/SQL type as table below:

  create or replace type typ_tbl_des_text is table of the typ_tof_des_text

  OK so far, but I would like to have a constructor function which would be subject to validations and raise_application_error when a validation condition is not met.

  How to do this?

  The typ_tof_des_text that I created with a constructor function, so that the record-level validation are performed in the constructor. And I think the postings between several records shall be made in a constructor for typ_tbl_des_tex, but cannot figure out how to create such a constructor.

  BEDE wrote:

  So, if I have understood correctly, to a plsql table type, I can't have a member procedure. Or can I? I mean, just as for a type of failure I can have one or more constructors and possibly several procedures of Member.

  For the standard tables in PL/SQL, you will need to create your own API (using procedures and functions) to handle beyond the basics provided by the language. No constructors and methods as it is no o - o.

  After thinking a little deeper, I reformulate what I said earlier and actually wants to have a member procedure called add_item, who would be first to check if an item with a key value exists and, if so, it would be up-to-date and so not only extend the plsql table.

  Two options.

  As we already mentioned, an associative array can be considered - note however that this structure of table has name-value pairs.

  Another method is to use a TWG (global temporary table). You define the structure of the once initial table. When a session uses the structure of the table, private copying is instantiated for this session. When the session ends, this copy is destroyed. The table is a temporary structure for this session only.

  It can include indexes and so on – which means you can use the constraints of primary keys, unique indexes, secondary indexes and so on.

  TWG scales are much better than collections or arrays that require a PGA (expensive private server) memory. In addition, SQL can be used natively against a GTT - unlike the arrays and collections.

• Two constraints of primary key of a table with two different constraint name

  Hi guys

  I am creating the table below

  Table name: TITLE_COPY

  Column name	Copy_id	Title_id	Status
  Key type	PK	PK, FK
  Unique	NN, U	NN, U	NN
  Check			Available, destroyed, leased, reserved
  Table Ref FK		Title
  FK Ref Col		Title_id
  Data type	Number	Number	Varchar2
  Length	10	10	15

  The SQL statement below can create it

  CREATE TABLE title_copy (copy_id NUMBER (10),)

  title_id CONSTRAINT NUMBER (10) title_copy_title_id_fk title (title_id) REFERENCES.

  primary key constraint title_copy_title_id_pk title_id (copy_id)

  status VARCHAR2 (15) NOT NULL CONSTRAINT status_ck CHECK (status IN ('AVAILABLE', 'DESTROYED', 'RENTAL', 'RESERVED'))

  );

  Two primary keys (title_id, copy_id) are created with the same name of constraint (title_copy_title_id_pk) (-> table-level constraint). What happens if I want to have two different names of the primary key constraint, say title_copy_title_id_pk for the title_id column and title_copy_copy_id_pk for the copy_id column?

  I can do that with a column-level constraint? Something like below (complains about the additional primary key)

  CREATE TABLE title_copy (copy_id NUMBER (10) CONSTRAINT title_copy_copy_id_pk PRIMARY KEY,)

  constraint title_copy_title_id_pk primary key (title_id).

  title_id CONSTRAINT NUMBER (10) title_copy_title_id_fk title (title_id) REFERENCES.

  status VARCHAR2 (15) NOT NULL CONSTRAINT status_ck CHECK (status IN ('AVAILABLE', 'DESTROYED', 'RENTAL', 'RESERVED'))

  );

  In summary, I can define two primary keys with the name of different constraint in a column-level constraint?

  There are no two primary keys. There is a primary key made up of two columns - also called a composite key.

  A table can have at least a primary key. You can, if you wish, create a unique constraint on a different set of columns.

• Deactivation of specific attributes in a table after insertion of line

  Hello
  
  I'm relatively new to Apex and me has encountered a problem. I'm trying to disable a few fields in the list of attributes in the form after the insertion is made. I want first two attributes to be read-only once they are inserted in the database, so that the user cannot change them. Any idea on how to do this? (Only one field is a LOV selection and the second is a date picker).
  
  Thanks in advance,
  Luka

  Ideally, you want to do it differently. Having a dynamic action that works on the loading of the page only works on the first page of the tabular presentation and not on other pages.
  Change the action dynamic event "After Refresh" on the region in a table.
  As a real action choose 'run javascript '. Check 'Fire on page load '.
  Note that my code will only change existing lines. It will remove the functionality of datepicker among elements on these lines, but not delete it form will add lines. DatePicker ("Destroy") is the standard way to remove a widget in jQuery UI, such as the date picker and returns the element to its 'pre-init State' (= the normal input field).
  An alternative to deactivation and activation of the elements, you can consider using just "readonly", because this will not be a change but sends his State on the server. Of course, it is not the same aspect as a disabled element, but it is something you can change by applying CSS to them.

  //select all input items with name attribute set to f10, within the context of the triggering element (=tabular form)
  //remove the widget state from each of the matched elements
  //set the readonly property (or disabled) to true. Similar to .attr("readonly","true") but better
  $("input[name='f10']", this.triggeringElement)
  .datepicker("destroy")
  .prop("readonly",true);  //or use .prop("disabled",true) to disable the item.
  

• Destroy / has WebView

  Hello
  Is there a way to destroy an instance WebView? If a page loads, and say a video begins to play, I want to be able, when I hide the WebView, essentially to destroy, or at least reset.
  I know that I could listen to the visibleProperty and do a getEngine () .load)
  But I was wondering if there was something better. Also, the visibleProperty does not change if the (false) webView.setVisible is executed just? He does not, for example, that the parent node of the not visible a webview.
  Appreciate your help.

  Well, there are two things here, we're not having it visible on the screen and the second that you can refer to what the trash of the object collected.

  (1) don't have not visible on the screen just delete what ever parent node it is in.

  someParent.getChildren().removeall(myWebView);
  

  or you can set the opacity of your webview to 0.

  (2) If you want t be the garbage collector, then you must remove all the references, you may have to it. This includes all collections (lists, sets, maps), tables, variable object and static variables. This topic goes beyond JavaFX and you can search further under the heading of collecting garbage forced or something to that effect.

  In addition, you can refer to something that is more specific to the Web format and its webEngine... like for example delete the webEngine of any page it can be loaded. I have not tested with webEngines but I do not see a clear method of sorts that turns off the screen. Loading may be NULL can turn off the display?

  Thank you
  Jose

  Published by: jmart Sep 14, 2012 21:58

• ComboBox in a table in a dialog box

  I have a dialog box that contains a table. Some of the columns of the table are drop-down list boxes.
  
  Some event of the dialog box appears with a number of rows (items) in the table. The drop-down list box contains all possible selections of the cell, which are objects of a class. The getValueAt() of my table model (extension of AbstractTableModel) method returns an object that exists in the combo box, so this object toString() representation is what is displayed normally. I can select the cell, get the drop-down list and make your choice and all is well. Or, if I click in another cell in the table, the combo is closed and the selection is displayed normally. There are buttons in the dialog box accept or cancel the values presented in the table.
  
  The problem I have is that if I select the cell, and the menu drop-down is displayed, but instead to make a selection, click on the Cancel button. What causes all elements in the array to be destroyed (without saving changes), and the dialog box rendered invisible. Then, when another event occurs and the same dialog made visible with new elements (lines), the previously selected cell is shown with the dark and down a drop-down list box border, but not the drop-down list. The cell displays the first item in the combo box, not the one that would have been returned by the method getValueAt() of the model. The selection of the element is not so indicated.
  
  I expect that when the dialog box is reshown and the rows of the table are rebuilt the remains of the drop-down list box would be gone. In other words, when the content of the table is destroyed and the dialog box is closed, I would expect for a cell to be arrested and not to forget the next time that the table is filled and shown editing.
  
  How can I make sure this happens?
  
  Thank you
  Wayne

  You must manually cancel editing of the cells before "destroy" the rows of the table.

  CellEditor editor = table.getCellEditor();
  if(editor != null) editor.cancelCellEditing();
  

  Similarly, you do not call stopCellEditing() when you press the OK button, so that any current change is recorded.

• Access the function of custom class which is stored in a table?

  Hello guys..,.

  
  I hope I am making stopper, with the title of the thread, because I'm a bit confused, how do you explain in Word...

  anyway I'll describe what I mean and hope you guys can help out me..,.

  Here I am doing some object of action script..,.

  What about this object that is in the constructor function of this object is as I do to send a parameter of sprite that will act as it's parent..,.

  var anObject:myObject = new myObject (parentSprite);
  

  and in my main project, I used those object and store in a table after it is added to the scene...

  I store it in a table cause I have to be able to return to the it...

  everything was fine until I have to call the function inside this object which I already stored in a table..,.

  so, how should I call the function in this table object that has stored the object?

  hope that I specify me...

  Thanks in advance guys..,.

  Well, the error is tell you that removeChild() destroy() function in the class Newsticker is having a problem because you try to remove a child does not belong to the parent. How your destroy() function looks like?

• Quick editing in multiple tables / multiple files

  I have a lot of files - all filled pages of tables - each table has several lines with a filtered bottom line (stroke). I would like to change the color of each of cyan (for example) 50% to 100% of Magenta in a swift move. I thought scripts or export for sharing and editing via XML. Both seem a bit overboard so I'm tender hand to ask for ideas.

  (Response to myself) That works, but it has been pointed out to me it does not work with the shades of the color chart. Besides, this shade is used elsewhere you will also change. You can find/replace contours and funds for any object... but not for the cells in a table! So, here's a script to do it.

  It's not really fast, because he must check each line and fill each cell of each table, but it will do the job very well.

  (Copy, paste in the editor of Adobe ESTK. Save it as "findChangeTableColor.jsx" in your folder Scripts user - if registered in the correct location, it automatically shows you in the actions panel. Double-click the script is running.)

  //DESCRIPTION:Change Table Fills and Strokes
  // Jongware, 18-Jul-2010
  myDialog = app.dialogs.add ({name:"Recolor Tables",canCancel:true});
  swatchlist = app.activeDocument.swatches.everyItem().name;
  with (myDialog)
  {
   with (dialogColumns.add())
   {
    with (borderPanels.add())
    {
     staticTexts.add ({staticLabel:"Find"});
     swf = dropdowns.add ({stringList:swatchlist, selectedIndex:0});
     tbf = percentComboboxes.add({editValue:100, largeNudge:10, stringList:["25", "50", "75", "100"] });
    }
    with (borderPanels.add())
    {
     staticTexts.add ({staticLabel:"Replace"});
     swr = dropdowns.add ({stringList:swatchlist, selectedIndex:0});
     tbr = percentComboboxes.add({editValue:100, largeNudge:10, stringList:["25", "50", "75", "100"] });
    }
    with (borderPanels.add())
    {
     dostrokes = checkboxControls.add({staticLabel:"Change strokes", checkedState:true});
     dofills = checkboxControls.add({staticLabel:"Change fills", checkedState:true});
    }
   }
  }
  if (!myDialog.show() || !(dostrokes.checkedState || dofills.checkedState))
  {
   myDialog.destroy();
   exit(0);
  }
  findtint = tbf.editValue;
  findswatch = app.activeDocument.swatches.item(swf.selectedIndex);
  changetint = tbr.editValue;
  changeswatch = app.activeDocument.swatches.item(swr.selectedIndex);
  strokes = dostrokes.checkedState;
  fills = dofills.checkedState;
  fillchanges = 0;
  strokechanges = 0;
  st = app.activeDocument.stories;
  for (s=0; s		   

• How to change a table of contents which originally from framemaker but we import is no longer the wire

  I apologize in advance because I'm a beginner user of robohelp. We had a framemaker file and pulled us in Robohelp. The table of contents generated quite well. But, for several reasons, mainly about how robohelp destroyed imported images from framemaker, we're now just edit the files in robohelp. I added a few items I want to appear in the output of webpro in the left navigation, but I can't understand how do. I'm sure whoever decided to address this need for more details but it seems that each technology author I know don't use robohelp. Help... robos, wherever you are...

  Hello

  The table of contents in RoboHelp are just a file. Basically, you open the editor table of contents as the first step. Usually, he came within a folder for the table of contents icon in your project manager. It is enough to click plus the sign or double-click with the record of the Table of contents. And then double-click the actual TOC to open the table of contents Editor.

  From here you insert, delete, or rearrange the books and Pages as you want. A simple way to add items to the table of contents must drag topics from the list of topics or the project manager in the table of contents Editor. Once you have done this, you can change the verbiage of the books in the table of contents and Pages.

  To create a book, you can use the icons at the top of the table of contents Editor, or you can right-click in the table of contents Editor.

  Hope this helps. If you need more, just ask!

  See you soon... Rick

  Useful and practical links Wish to RoboHelp form/Bug report form Begin to learn RoboHelp HTML 7 or 8 days - $24.95! Adobe Certified RoboHelp HTML Training SorcerStone blog RoboHelp EBooks