Devices configured for authentication under ACS

Similar Questions

• Autonomous AP521 can be configured for authentication WPA/TKIP with no radius server?

  The AP521 can be configured for authentication WPA/TKIP with no radius server?

  the datasheet, wpa with tkip and wpa2 with aes are supported.

  you want to use (no RADIUS) wpa - psk with tkip. WPA2-psk aes and tkip not use.

• several hosts aaa server for authentication vpn

  ASA5510 - 7.2 (1)

  Using the following configuration, I try to have several radius servers configured for authentication backup in case of failure of the primary vpn. This seems to work ok. But once the main server upward when the asa will begin to use it again. The release of "aaa-Server 172.25.4.20 host" said

  Server status: FAILURE, server disabled at 08:04:25.

  How do reactivate you it?

  RADIUS protocol AAA-server adauth

  adauth AAA-server 172.25.4.20

  key *.

  authentication port 1812

  accounting-port 1813

  adauth AAA-server 172.25.4.40

  key *.

  authentication port 1812

  accounting-port 1813

  tunnel-group group general attributes

  address pool pool

  authentication-server-group adauth

  by default-group-policy

  You can add the option in the Group aaa-server:

  "reactivation in timed mode.

  This causes a dead server is added to the pool after 30 seconds.

  The following link has some good info on the options available. I suggest looking for the doc for the "reactivation".

  http://www.Cisco.com/univercd/CC/TD/doc/product/multisec/asa_sw/v_7_2/cmd_ref/crt_711.PDF

  -Eric

  Be sure to note all the useful messages.

• Invalid configuration for the device 3

  Hi all

  I have set up a lab nested with three hosts esxi and two warehouses of data connected with the Microsoft iscsi target server. I know nested vm is not supported, but I'm trying to implement this workshop because I support a real VMware environment and I wish I could test some things before I break anything, so it's important. I get this error when you try to create a virtual machine "invalid configuration for the device 3.  Someone knows how can I know where is the problem?

  Thank you

  I think I can find the answer, it seems that it could be a windows problem causing data corruption. Somehow I created a VM but get all kinds of error trying to create an another VM.  Iscsi targets set up using windows server 2012 and it seems that there is a fix from Microsoft below which deals with corruption LUNs in windows 2012.  I have not yet tested, but this seems to be the right direction. http://support.Microsoft.com/kb/2908783

• Configuration of the Cisco ACS 5.3 AnyConnect VPN and management of a Cisco ASA 5500.

  We have configured a Cisco ASA 5505 as a VPN endpoint for one of our user groups.  It works, but it works too well.

  We have a group called XXX we need to have access to the Cisco AnyConnect Client.  We have selected this group of our Active Directory and added to our ACS configuration.  We've also added a group called YYY that will manage the ASA. However, this group has no need to access the VPN.

  We added XXX movies for the elements of the policy of access to the network-> authorization profiles.  We also have a profile of YYY.

  She continues to knock on our default Service rule that says allow all.

  We have also created a default network access rule. for this.

  I am at a loss.  I'm sure I missed a checkbox or something.

  Any help would be really appreciated.

  Dwane

  We use Protocol Management GANYMEDE ASA and Ray for VPN access?

  For administration, you must change the device by default admin access strategy and create a permission policy. Even by the way, you can change the network access by default for vpn access and create a respective policy for that too.

  On the SAA, you must configure Ganymede and Ray both as a server group.

  For the administration, you can set Ganymede as an external authentication under orders aaa Server

  AAA-server protocol Ganymede GANYMEDE +.

  Console HTTP authentication AAA GANYMEDE

  Console Telnet AAA authentication RADIUS LOCAL

  authentication AAA ssh console LOCAL GANYMEDE

  Console to enable AAA authentication RADIUS LOCAL

  For VPN, you must set the authentication radius under the tunnel-group.

  I hope this helps.

  Kind regards

  Jousset

  The rate of useful messages-

• How to separate requests for authentication to GBA 4.2

  Hello

  I have a 4.2 ACS for AAA. Right now I use this server to authenticate users this connection for all my devices cisco (routers, switches, ASAs, APs) and also to authenticate users for remote access VPN to ASA.

  The problem I have is that VPN users residing on another group in ACS are able to authenticate to log to manage network devices and it is a problem of security. I need the vpn users only being able to authenticate to the vpn and not be able to authenticate to connect to network devices.

  Any ideas? is it possible to separate requests for access radius and vpn connection?

  Hi Fernando,

  Yes it is possible to restrict your users only VPN to VPN - ASA. If you want that they do not have telnet/ssh/http access with other devices in the network, then you can go for NAR (network access restriction).

  The only thing you need to know what we are calling-station-id. I think it's an ip address. You can check this activity and reports > past authentication for VPN users.

  Here are the steps:

  GBA > go to the VPN group > Edit > search for NAR > under Ip based NAR > set the action to "DECLINED" > select the devices (routers/switches) you want to deny access to > put * for the port field and address > click on submit + restart.

  Doing this will of users can connect through vpn and unable to do ssh and telnet.

  I have attached the screenshot of the same thing (I did for 6509 switch)

  HTH

  JK

  Please evaluate the useful messages-

• Cannot save an ACS secondary for replication of ACS primary 5.2.

  Hello

  I hope someone can help me.  Currently, I have two devices Cisco ACS and both are classified in the PRIMARY.  The first ACS is running version 5.2.0.26 while the second ACS is running version 5.3.0.40.

  My original thought was to install the first ACS and do serve primary and have it replicate its data on the ACS SECONDARY.  Somehow, after installation, the ACS are now listed as PRIMARY.  When I go into secondary ACS under Deployment Options to try to save it in elementary school, I get the following error message:

  "This failure has occurred.  Failed to authenticate with node.  Your changes have not been saved. »

  Even if I try this GBA primary to save it for the secondary ACS, I get the same error message.  I tried all passwords including the credentials of the admin super user, my credentials for the administrator and the credentials provided to SSH in ' GBA and nothing is helping.

  Reading online, I read there was a way to remove an ACS secondary, but I don't have the ability to add this server in the primary for "bump it down" to a secondary antibody hoping to save it for the primary ACS.

  If anyone can give me some pointers, I would greatly appreciate.

  Thank you, and all have a wonderful day.

  THERE

  Yvonne,

  If the identifier is the same then definitely replication does not work, you will not be able to enroll in primary school if the license is the same. The good side is that you have the other license, you only need to install.

  However I have more bad news, the only way to re - install a license file in ACS 5.x uses the CLI command 'acs reset-config', but it will also delete all of the configuration that you have on this server, except the network configuration (IP, gateway, DNS, etc.)

  After entering this command if you are trying to access the GUI, you should not use the name of user and password acsadmin/default, then you will be asked to locate the license file.

  Here is a document with this information where you need it:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/my_wkspc.html#wp1052906

• Problem setting 7606 router for authentication GANYMEDE +.

  Hello community support.

  I have two routers Cisco 7606 I tried in vain to have users authenticated using servers GANYMEDE +. As noted below, I have two servers (1.1.1.1 and 2.2.2.2) accessible via vrf OAM which is accessible from desktop to ssh login. The real IPS and FFS have been changed because it's a router of the company.

  I use two servers to authenticate on a lot other devices Cisco network that they work properly.

  I can reach the vrf servers and the source in use interface. I can also port telnet 49 if the source interface servers and the vrf.

  The server key is hidden, but at the time of configuration, I can see that it is correct.

  The problem is that after confuring for authentication RADIUS, the router always uses the password to enable instead of GANYMEDE. While debug output shows "incorrect password", why not the router authenticates using GANYMEDE? Why is he using the enable password?

  Please review the outputs below and help point out what I may need to change.

  PS: I have tried many other combinations, including obsolete without success, including the method proposed in this page.

  http://www.Cisco.com/en/us/docs/iOS/sec_user_services/configuration/guide/sec_vrf_tacas_svrs.html

  Please help I'm stuck.

  ROUTER #sh running-config | s aaa

  AAA new-model

  AAA server Ganymede group + admin

  Server name admin

  Server name admin1

  IP vrf forwarding OAM

  Ganymede IP interface-source GigabitEthernet1

  AAA authentication login admin group Ganymede + local activate

  AAA - the id of the joint session

  ROUTER #sh running-config | dry Ganymede

  AAA server Ganymede group + admin

  Server name admin

  Server name admin1

  IP vrf forwarding OAM

  Ganymede IP interface-source GigabitEthernet1

  AAA authentication login admin group Ganymede + local activate

  GANYMEDE Server Admin

  1.1.1.1 ipv4 address

  button 7 XXXXXXXXXXXXXXXXXXXX

  GANYMEDE Server admin1

  2.2.2.2 ipv4 address

  button 7 XXXXXXXXXXXXXXXXxxxx

  line vty 0 4

  authentication admin login

  ROUTER #sh Ganymede

  GANYMEDE + - public server:

  Server name: admin

  Server address: 1.1.1.1

  Server port: 49

  Opening of socket: 15

  Firm grip: 15

  Write-offs of socket: 0

  Socket errors: 0

  Socket timeouts: 0

  Failed connection attempts: 0

  Total packets sent: 0

  Recv packets total: 0

  GANYMEDE + - public server:

  Server name: admin1

  Server address: 2.2.2.2

  Server port: 49

  Opening of socket: 15

  Firm grip: 15

  Write-offs of socket: 0

  Socket errors: 0

  Socket timeouts: 0

  Failed connection attempts: 0

  Total packets sent: 0

  Recv packets total: 0

  Oct 22 12:38:57.587: AAA/BIND(0000001A): link i / f

  22 Oct 12:38:57.587: AAA/AUTHENTIC/LOGIN (0000001 a): Select method list "admin".

  Oct 22 12:38:57.587: AAA/AUTHENTIC/ENABLE(0000001A): action of treatment application LOGIN

  Oct 22 12:38:57.587: AAA/AUTHENTIC/ENABLE(0000001A): reported GET_PASSWORD

  Oct 22 12:39:02.327: AAA/AUTHENTIC/ENABLE(0000001A): action of treatment application LOGIN

  Oct 22 12:39:02.327: AAA/AUTHENTIC/ENABLE(0000001A): reported FAIL - wrong password

  22 Oct 12:39:04.335: AAA/AUTHENTIC/LOGIN (0000001 a): Select method list "admin".

  Oct 22 12:39:04.335: AAA/AUTHENTIC/ENABLE(0000001A): action of treatment application LOGIN

  Oct 22 12:39:04.335: AAA/AUTHENTIC/ENABLE(0000001A): reported GET_PASSWORD

  Oct 22 12:39:08.675: AAA/AUTHENTIC/ENABLE(0000001A): action of treatment application LOGIN

  Oct 22 12:39:08.675: AAA/AUTHENTIC/ENABLE(0000001A): reported FAIL - wrong password

  22 Oct 12:39:10.679: AAA/AUTHENTIC/LOGIN (0000001 a): Select method list "admin".

  Oct 22 12:39:10.683: AAA/AUTHENTIC/ENABLE(0000001A): action of treatment application LOGIN

  Oct 22 12:39:10.683: AAA/AUTHENTIC/ENABLE(0000001A): reported GET_PASSWORD

  Oct 22 12:39:14.907: AAA/AUTHENTIC/ENABLE(0000001A): action of treatment application LOGIN

  Oct 22 12:39:14.907: AAA/AUTHENTIC/ENABLE(0000001A): reported FAIL - wrong password

  ROUTER #sh worm

  Cisco IOS software, software of c7600rsp72043_rp (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1 (3) S3, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2012 by Cisco Systems, Inc.

  Updated Saturday, March 30, 12 08:34 by prod_rel_team

  ROM: System Bootstrap, Version 12.2 SRE (33r), RELEASE SOFTWARE (fc1)

  BOOTLDR: Cisco IOS software, software c7600rsp72043_rp (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 15.1 (3) S3, RELEASE SOFTWARE (fc1)

  The availability of ROUTER is 7 weeks, 5 days, 16 hours, 48 minutes

  Availability for this control processor is 7 weeks, 5 days, 16 hours, 49 minutes

  System returned to ROM by reload (SP by charging)

  System restarted at 20:00:59 UTC Wednesday, August 28, 2013

  System image file is "sup - bootdisk:c7600rsp72043 - advipservicesk9 - mz.151 - 3.S3.bin.

  Last reload type: normal charging

  Reload last reason: power

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Processor CISCO7606 - S (M8500) Cisco (revision 1.1) with 3670016 K/K 262144 bytes of memory.

  Card processor ID FOX1623G61B

  PLINTH: RSP720

  CPU: MPC8548_E, Version: 2.1 (0 x 80390021)

  KERNEL: E500, Version: 2.2, (0 x 80210022)

  CPU:1200 MHz, CCB:400 MHz, DDR:200 MHz,

  L1: D-cache 32 KB active

  I'm hiding active 32 KB

  Last reset of tension

  3 virtual Ethernet interfaces

  76 of the gigabit Ethernet interfaces

  8 ten interfaces Ethernet Gigabit

  3964K bytes of non-volatile configuration memory.

  500472K bytes of the map of PCMCIA ATA internal (512 bytes sector size).

  Configuration register is 0 x 2102

  To resolve this problem. Please replace the below listed order

  AAA authentication login admin group Ganymede + local activate

  with;

  Enable AAA authentication login default local admin group

  You have set the group name server as a list of methods and instead use admin as a group of servers, you used Ganymede +.

  Note: Please ensure that you have local users and enable the password configured in the case of Ganymede inaccessible server.

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• Registration for authentication and crossing area of Jabber

  Hello

  I used TMS 13.1.2 as authentication source LDAP for VCS-control and VCS Expressway, but noticed, that not all passwords are synchronized correctly in the LDAP H.350 MSDS database, because the user is recorded in two entries. I went to the local authentication, including the database configuration on VCS - C and the local database with the transmission by proxy SIP VSC-E to the VCS - C records. It works fine and I am able to make calls.

  I created the search on VCS highway rules to replace all aliases MCU to an auto attendant external special. Stored locally on the VCS-E endpoint points are allowed to call internal aliases. I tried to do the same for the Jabber Clients, which is recorded in the crossing area of the VCS - C. This works as expected, because the Jabber Clients are not enrolled in a local area and SIP GUEST is not in dispute.

  I expect that all the Jabber client message will be challenged by the VCSE, but this isn't the case. Accordingly, the guest of the SIP protocol is treated as an external user and not an intern.

  May 9 10:11:28     tvcs: UTCTime="2012-05-09 08:11:28,425" Module="network.search" Level="INFO": Detail="Search rule 'my.domain proxy registrations' did not match destination alias [email protected]/* */'"
May 9 10:11:28     tvcs: UTCTime="2012-05-09 08:11:28,423" Module="network.sip" Level="INFO": Dst-ip="84.113.206.194" Dst-port="62503" Detail="Sending Response Code=100, Method=INVITE, To=sip:[email protected]/* */, [email protected]/* */"
May 9 10:11:28     tvcs: UTCTime="2012-05-09 08:11:28,419" Module="network.sip" Level="INFO": Src-ip="84.113.206.194" Src-port="62503" Detail="Receive Request Method=INVITE, Request-URI=sip:[email protected]/* */, [email protected]/* */"

  These are the rules of research that I was talking about:

  110     Enabled     "local registered to Traversal"     LocalZone      No      Alias pattern match      Regex      ^(.*)@my.domain$      Leave      Continue      TraverselZone
115     Enabled     "authenticated to internal"     Any      Yes      Alias pattern match      Regex      ^(.*)@my.domain$      Leave      Continue      TraverselZone
120     Enabled     "mcu all to 899"     Any      No      Alias pattern match      Regex      ^(900\d*|conference)@nts\.eu$      Replace      Stop      TraverselZone

  Is it possible to allow the Jabber Clients to be authenticated on the VCS-E, so a search rule can aply?

  Thanks for your help!

  You get the 'Preparation device' key for your VCS-E so its free.

  It may require a valid service contract.

  I have the provisioning again running on a cluster of VCS - E in my lab, works very well.

  In ancient times that the deployment has not officially supported, it was running great in any case :-)

  Did not check if its now a deployment with support.

  I don't know enough about your deployment to say what would be the best for you.

  There will be some scenarios where not all features can be deployed together for some reason any.

  Maybe someone can help you by looking at how implementation could be done better.

  If you have authentication and integration of ads, that you need to connect

  the VCS-E announced as well. Endpoints (at least for now) is not auth via AD, but you could

  use a database of h.350 (could also be hosted with AD) or the local authentication database.

  Now, which is also spread by TMS, could be an answer to your question as well.

• Authentication Radius ACS with WLC 5508 and AD 2012 5.5 failure

  Hello

  I need help on these errors.

  Here is my configuration: WLC 5508 7.6.130.0-> ACS 5.5.0.46-> AD 2012

  I have (2) errors in ACS 5.5

  12514 EAP - TLS failed SSL/TLS handshake because of unknown CA in the client certificate chain

  22044 result of identity politics is configured for certificate-based authentication methods but based received password

  Already installed the CA cert and cert local in ACS as well as in the client PC.

  Please see screenshots

  OK, in this case:

  1. you will need to properly configure the Windows pleading before that this can work. You need to set the type of authentication and the trusted certification authority. If the certification authority is not available in the list of certificates, you need to import

  2. If you do PEAP then your identity store should be Active Directory and no profile authentication certificate. The certificate authentication profile is used for the basis of certificates (EAP - TLS) authentication.

  Thank you for evaluating useful messages!

• NPS Windows Help for authentication of aaa for Cisco router - is it safe?

  I am very confused about how all this works and was hoping someone could help me.

  I followed a bunch of tutorials online for authentication RADIUS of installation on a Cisco router and he did to a NPS Windows Server. Now I can ssh into the router my AD account.

  Now that I got it to work, I go to the settings to make sure everything is secure.

  On my router, the config is pretty simple:

  aaa new-modelaaa group server radius WINDOWS_NPSserver-private 123.123.123.123 auth-port 1812 acct-port 1813 key mykeyaaa authentication login default local group WINDOWS_NPS
  
  ip domain-name MyDomcrypto key generate rsa
  
  (under vty and console)# login authentication default
  On the NPS Windows:
  I created a new RADIUS client for the router.
  Created a secret shared and specified Cisco as the name of the seller.
  Created a new strategy of network with my desired conditions.
  And now the frame of the configuration of the network policy that worries me:
  
  
  So initially I thought my AD credentials were being sent over the wire in plain text, but I did a capture and saw this:
  
  
  
  capture.jpg
  
          
      
  
  
  How is my password being encrypted and how strong is the encryption?
  
  Another thing is how can I configure aaa authentication with mschapv2? The documentation I saw for mschapv2 uses the "ppp authentication ms-chap-v2" command, but I'm not using ppp I'm using aaa with a radius server.
   
  			 
  Hello
  RADIUS encrypts the password, but sends the username in clear. GANYMEDE encrypts the user name and password.
  You can find the encryption used by RADIUS in the RFC scheme:
  https://Tools.ietf.org/html/rfc2865#page-27
  MS-Chap-V2 is used for the authentication of users such as the remote access and vpn, not management switch
  Thank you
  John
  		   

• Configuration of the Cisco ACS Radius

  Hello

  I'm trying to set up authentication radius on cisco ACS but short question. When I set up my group of network devices in the configuration of the AAA Client as one of ray device groups, my authentications fail with authentication as a failure code"

  CS invalid password' but when I change my group of devices to "Unassigned", everything started working.

  On my AAA client, when authentication fail, I see

  Server RADIUS audit package fails:

  Please note that the AAA client is a non-cisco device.

  Any suggestions?

  It seems that you run ACS 4.x. You are facing this problem because the key is set on the excessive rides of the level (Group of devices network XYZ in your case) NDG key at the level of the AAA client.  Please make sure that you don't have different secret key on the client inside the NDG AAA and on the NDG himself.

  Not affected is working because it has no key defined in the NDG.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/NetCfg.html#wp342738

  "Each device that is assigned to the network device group will use the shared key you enter here. The key that has been attributed to the device when it has been added to the system is ignored. If the Enter key is null, the key of the AAA client is used. »

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• Firefox doesn't show popup for authentication

  I use firefox for internet access through my University proxy. I type my password and my user account.
  Recently, firefox does not show the popup for authentication, where I type my user account and my password, so I can't access my network of the University. I have not changed the proxy configuration (I checked it, it's as it should be).
  When I try to access any Web site, I get the message "access to the cache of refused" and it says that I have to authenticate to access. However, there is no authentication window to enter my user account and password.
  I tried to configure Chrome and Safari, and they worked perfectly.
  My computer is a mac running the mavericks.

  See:

  • https://developer.Mozilla.org/en-us/Firefox/releases/30/Site_Compatibility#security

  In Firefox 30 and later NTLMv1 auth has been disabled, NTLM supported on platforms other than Windows is now obsolete

  In Firefox 31 for NTLMv1 auth has been restored to only secure connections (Bug 1023748).

  • Network.Negotiate - auth.allow - insecurity-ntlm-v1 = false
  • Network.Negotiate-auth.allow-insecure-NTLM-v1-https = true
  • bug 1023748 - Allow NTLMv1 via SSL/TLS or intranet access is broken on Firefox 30 for platforms other than Windows

• Want 4500: Device Configuration-> device non-reachable

  My new envy 4500 _IS_ on my network.

  My new MacBook Pro _IS_ on my network.

  I get to the configure step and everything looks good, until I get the answer below:

  "Device setup".

  0 select device

  0 confirm the anti-piracy settings

  O select network

  Device configuration

  The configuration results

  Non-contacted device

  TH wireless settings) have been downloaded successfully on your device. However, your Mac

  could not locate the device on the network.

  Please make sure that:

  • Your Mac is connected to a wired or wireless network that has access to your device.

  • Your device is connected to the wireless network ' network of current alternative.

  ' Fomorians of information online, visithftp: / /www.hp.com/o/wirelessprinting '

  This is the second HP printer that I am trying to set up makes the same "thing".  I thought the first was defective, so I traded for a different printer.  It has a display of control, so I KNOW it's on the network.  And I KNOW my computer is on the network, or I wouldn't be able to write this.

  But they refuse to talk to each other.  SO frustrating.  I'm willing to give up HP.

  Joe

  Found the problem.  HP printers do not support Wifi AC.  It would have been nice to know before I wasted 4 hours on 2 printers...

• LAPN300 - the best configuration for 3 access points, while using the same SSID

  Hi all

  What is the best configuration for 3 x LAPN300 located in various places around my house of 3 floors, access points if I want just one SSID?

  I did some initial research which suggests that I can use the same SSID on all three, as long as they are on different channels. 1, 6 and 11 for example. In theory, then, as I wander around the House the client machine must auto swap to the AP with the signal stronger.

  What do you think? What is the best way or do, or could suggest you something else?

  As an aside... If I decided to create a second SSID for the guests at home, I would also want to add wireless isolation to this SSID. How would that be managing the DHCP server on the local network? How would be asked to connect to the SSID has never get an IP if they have been isolated from other clients on the local network?  Besides, how they see the router? The ANNUAL lets you specify exceptions to this isolation for this feature?  Alternatively, as I suspect, is the right isolation feature isolate them from other WLAN, not the LAN clients customers?

  I did some testing and configuration of the AP with the same SSID and security will do what you want. Don't worry about setting the channel because the auto channel setting works with these devices and automatically adjusts the spacing between the appropriate channels.

  Recommendation of the VPN_user is what you need if you want to isolate the SSID comments from the rest of your network clients.

  Isolation of SSID of the AP will guard only wireless devices to communicate with each other on the same SSID on which it is enabled.