Configuration of the Cisco ACS Radius
Hello
I'm trying to set up authentication radius on cisco ACS but short question. When I set up my group of network devices in the configuration of the AAA Client as one of ray device groups, my authentications fail with authentication as a failure code"
CS invalid password' but when I change my group of devices to "Unassigned", everything started working.
On my AAA client, when authentication fail, I see
Server RADIUS
Please note that the AAA client is a non-cisco device. Any suggestions? It seems that you run ACS 4.x. You are facing this problem because the key is set on the excessive rides of the level (Group of devices network XYZ in your case) NDG key at the level of the AAA client. Please make sure that you don't have different secret key on the client inside the NDG AAA and on the NDG himself. Not affected is working because it has no key defined in the NDG. "Each device that is assigned to the network device group will use the shared key you enter here. The key that has been attributed to the device when it has been added to the system is ignored. If the Enter key is null, the key of the AAA client is used. » ~ BR * Does the rate of useful messages *. Tags: Cisco Security Configuration of the Cisco ACS 5.3 AnyConnect VPN and management of a Cisco ASA 5500. We have configured a Cisco ASA 5505 as a VPN endpoint for one of our user groups. It works, but it works too well. We have a group called XXX we need to have access to the Cisco AnyConnect Client. We have selected this group of our Active Directory and added to our ACS configuration. We've also added a group called YYY that will manage the ASA. However, this group has no need to access the VPN. We added XXX movies for the elements of the policy of access to the network-> authorization profiles. We also have a profile of YYY. She continues to knock on our default Service rule that says allow all. We have also created a default network access rule. for this. I am at a loss. I'm sure I missed a checkbox or something. Any help would be really appreciated. Dwane We use Protocol Management GANYMEDE ASA and Ray for VPN access? For administration, you must change the device by default admin access strategy and create a permission policy. Even by the way, you can change the network access by default for vpn access and create a respective policy for that too. On the SAA, you must configure Ganymede and Ray both as a server group. For the administration, you can set Ganymede as an external authentication under orders aaa Server AAA-server protocol Ganymede GANYMEDE +. Console HTTP authentication AAA GANYMEDE Console Telnet AAA authentication RADIUS LOCAL authentication AAA ssh console LOCAL GANYMEDE Console to enable AAA authentication RADIUS LOCAL For VPN, you must set the authentication radius under the tunnel-group. I hope this helps. Kind regards Jousset The rate of useful messages- restore the configuration of the cisco ACS 1121 ver 5.2 to SNS 3425 ver 5.6 Dear all, We currently have Cisco ACS 1121 ver 5.2 in our production, then we will replace it with the new devices using SNS 3425 ver 5.6. Please good to want to help someone can tell you how to restore all the old configuration of devices (ACS 1121 ver 5.2) for the new Member States? Best regards Yudibagam Hello! You must upgrade the current device to a min of v5.4 for restoration work and be supported. However, if you're going to go through the upgrade problems then I would say that you upgrade all the way to 5.6 just to be sure :) I hope this helps! Thank you for evaluating useful messages! Correct configuration of the Cisco Access Point 1242AG Hi all Here's the situation: Recently, we decided to create a small network of WLAN in our company. We choose the Cisco AIR-AP1242AG-E-K9 with 2x2.4GHz 2.2dbi rotating dipole antenna. For better management, a new VLAN routable (ID:20) added to our router IP 192.168.55.1 and SNET 255.255.255.0 Then, I made the following configurations in the autonomous AP through WEB Console: I can ping VLAN20 IPs from any PC which is a member of the VLAN native both AP As wireless clients, I use 2 Motorola MC5574 with Windows Mobile 6.1 professional. Both of them have a WLAN Jedi adapter that is configured with the following: IPs:192.168.55.10 and 192.168.55.11 SNET:255.255.255.0 GWY:192.168.55.1 In addition, a unique profile has been created on all of them to use for the authentication of the association AP. Each profile has been configured for WPA2-Enterprise with AES and LEAP and identification information predefined user (those defined in the PA for individual users) The problem: Association of clients with AP is always successful but, authentication fails, and I can't ping the AP IP, IP VLAN20, nor the other customers. What I'm missing here? I'm sure it's quite simple somenthing but although I tried several different configurations (even WPA - PSK, WPA2-PSK with TKIP) I always find myself without an appropriate solution to unable to ping. Thanks in advance for any help Hello Can you please paste the show run out of AP? Kind regards Madhuri Configuration of the Cisco etherchannel stack: flag stuck in stand alone I'm putting in place an etherchannel for my stack of Cisco (switch Catalyst 3750 G x 2), with a port on each switch the etherchannel. The example of battery cross http://www.cisco.com/en/US/products/hw/switches/ps5023/products_configuration_example09186a00806cb982.shtml using as a guide, I created my channel. However when I discovered "show etherchannel summary 6 ' it says that both my ports are stand-alone, when I want them to be in port channel grouped in. Thank you in advance for your help, I added all the information I could think. Here is how I created the etherchannel sailing-sw-1 #conf t sailing-sw-1 (config) #interface gigabiteethernet 0/1/10 active in sail-sw-1(config-if) mode #channel-group 6 sailing-sw-1(config-if) #switchport trunk encapsulation dot1q sailing-sw-1(config-if) #switchport mode trunk sailing-sw-1(config-if) #exit sailing-sw-1 (config) #interface gigabiteethernet 0/1/10 active in sail-sw-1(config-if) mode #channel-group 6 sailing-sw-1(config-if) #switchport trunk encapsulation dot1q sailing-sw-1(config-if) #switchport mode trunk sailing-sw-1(config-if) #exit sailing-sw-1 (config) #exit The running-config sailing-sw-1 #show running-config Building configuration... Current configuration: 5390 bytes ! version 12.2 no service button horodateurs service debug uptime Log service timestamps uptime no password encryption service ! sailing-sw-1 hostname ! boot-start-marker boot-end-marker ! Select the 5 secret... ! ! ! high-level description of the cisco-global macro No aaa new-model 1 supply ws-c3750g-24ts switch 2 available ws-c3750g-24ts switch mtu 1500 routing system Uni-directional aggressive ! ! ! MLS qos map cos-dscp 0 8 16 24 32 46 46 56 ! Crypto pki trustpoint TP-self-signed-538118016 enrollment selfsigned name of the object cn = IOS - Self - signed - certificate - 538118016 revocation checking no rsakeypair TP-self-signed-538118016 ! ! TP-self-signed-538118016 crypto pki certificate chain certificate self-signed 01 30... AF quit smoking ! ! ! errdisable recovery cause link-flap 60 errdisable recovery interval port-channel - the balance of the load src-dst-mac ! spanning tree mode rapid pvst spanning tree default loopguard No spanning tree optimize transmission of bpdus spanning tree extend id-system ! internal allocation policy of VLAN ascendant ! ! ! Interface Port-channel6 ! GigabitEthernet1/0/1 interface No auto mdix ! interface GigabitEthernet1/0/2 No auto mdix ! interface GigabitEthernet1/0/3 No auto mdix ! interface GigabitEthernet1/0/4 No auto mdix ! interface GigabitEthernet1/0/5 No auto mdix ! interface GigabitEthernet1/0/6 ! interface GigabitEthernet1/0/7 No auto mdix ! interface GigabitEthernet1/0/8 No auto mdix ! interface GigabitEthernet1/0/9 No auto mdix ! interface GigabitEthernet1/0/10 switchport trunk encapsulation dot1q switchport mode trunk No auto mdix active in mode channel-group 6 ! interface GigabitEthernet1/0/11 No auto mdix ! interface GigabitEthernet1/0/12 No auto mdix ! interface GigabitEthernet1/0/13 No auto mdix ! interface GigabitEthernet1/0/14 No auto mdix ! interface GigabitEthernet1/0/15 No auto mdix ! interface GigabitEthernet1/0/16 No auto mdix ! interface GigabitEthernet1/0/17 No auto mdix ! interface GigabitEthernet1/0/18 No auto mdix ! interface GigabitEthernet1/0/19 No auto mdix ! interface GigabitEthernet1/0/20 No auto mdix ! interface GigabitEthernet1/0/21 No auto mdix ! interface GigabitEthernet1/0/22
No auto mdix ! interface GigabitEthernet1/0/23 No auto mdix ! interface GigabitEthernet1/0/24 No auto mdix ! interface GigabitEthernet1/0/25 ! interface GigabitEthernet1/0/26 ! interface GigabitEthernet1/0/27 ! interface GigabitEthernet1/0/28 ! GigabitEthernet2/0/1 interface No auto mdix ! interface GigabitEthernet2/0/2
No auto mdix ! interface GigabitEthernet2/0/3 No auto mdix ! interface GigabitEthernet2/0/4 No auto mdix ! interface GigabitEthernet2/0/5 No auto mdix ! interface GigabitEthernet2/0/6 ! interface GigabitEthernet2/0/7 No auto mdix ! interface GigabitEthernet2/0/8 No auto mdix ! interface GigabitEthernet2/0/9 No auto mdix ! interface GigabitEthernet2/0/10 switchport trunk encapsulation dot1q switchport mode trunk No auto mdix active in mode channel-group 6 ! interface GigabitEthernet2/0/11 No auto mdix ! interface GigabitEthernet2/0/12 No auto mdix ! interface GigabitEthernet2/0/13 No auto mdix ! interface GigabitEthernet2/0/14 No auto mdix ! interface GigabitEthernet2/0/15 No auto mdix ! interface GigabitEthernet2/0/16 No auto mdix ! interface GigabitEthernet2/0/17 No auto mdix ! interface GigabitEthernet2/0/18 No auto mdix ! interface GigabitEthernet2/0/19 No auto mdix ! interface GigabitEthernet2/0/20 No auto mdix ! interface GigabitEthernet2/0/21 No auto mdix ! interface GigabitEthernet2/0/22 No auto mdix ! interface GigabitEthernet2/0/23 No auto mdix ! interface GigabitEthernet2/0/24 No auto mdix ! interface GigabitEthernet2/0/25 ! interface GigabitEthernet2/0/26 ! interface GigabitEthernet2/0/27 ! interface GigabitEthernet2/0/28 ! interface Vlan1 the IP 192.168.0.1 255.255.255.0 ! default IP gateway - 192.168.76.102 IP classless IP http server IP http secure server ! activate the IP sla response alerts ! ! Line con 0 line vty 0 4 password Mil19 opening of session line vty 5 15 password Mil19 opening of session ! end Interface port-channel 6 (in the example, there should be this line "identified in this channel: Gi2/article-gi1/0/10 0 / 10 ') sailing-sw-1 #show interfaces port-channel 6 Channel6 port is down, line protocol is down (notconnect) Material is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set KeepAlive set (10 sec) Link auto-duplex type, automatic speed is automatic, media type is unknown input stream control is turned off, output flow control is not supported Type of the ARP: ARPA, ARP Timeout 04:00 Last entry, never, never hang output Final cleaning of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0 Strategy of queues: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bps, 0 packets/s 5 minute output rate 0 bps, 0 packets/s 0 packets input, 0 bytes, 0 no buffer Received 0 emissions (0 multicasts) 0 Runts, 0 giants, 0 shifters entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored Watchdog 0, multicast 0, break 0 comments entry packets 0 with condition of dribble detected exit 0 packets, 0 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, collision end 0, 0 deferred carrier, 0 no carrier, lost 0 0 output BREAK output buffer, the output buffers 0 permuted 0 failures EtherChannel 6 Summary sailing-sw-1 #show etherchannel 6 Summary Flags: - Low P - D bundled in port-channel
I have - autonomous s - suspended H Eve (LACP only) R - Layer 3 S - Layer2 U - running f - cannot allocate an aggregator M - don't use, minimum contacts not satisfied u - unfit to tied selling w waiting to be aggregated d default port Number of channels: 1 Number of aggregators: 1 Protocol for the Port-Channel port group ------+-------------+-----------+----------------------------------------------- 6 Po6 (SD) LACP Gi1/0/10 (I) Gi2/0/10 (I) Hello It seems that the grouping of NIC Linux box does not work properly. Please Check on the side of Linux. Kind regards NT D9036 - GUI Login - IP Configuration of the Cisco encoder Dear all I try to open D9036 encoder Cisco to get access to the Web Interface of GUI. In the manual of the encoder, Cisco informed that we have to connect via RS232 to the encoder and configure its IP address, but I did not but I noticed that the encoder Eth1 has an IP "192.168.1.100" and whenever I am trying to ping ping. Please advice for the method to connect to the encoder via the Web Interface of GUI. Follow these steps: 2 in the main connection, type root and then press ENTER. 3 at the root prompt, type set_mgmt_port_config.py and press ENTER. 8 networking restart for guest MGMT port, type y and press ENTER to apply the changes immediately. 9 type ifconfig to check the ip address. 10. after the above steps, try to encode via GUI. It should work. ACS RADIUS timeout with WLC 7.0 5.0 Hi guys,. I'm setting up a device Cisco Secure ACS 1120 running 5.0.0.21 ACS to manage the RADIUS of a Cisco WLC 5508 device query running the 7.0.116.0 version. The following statements illustrate some but not all debugging I did to make sure that each device works properly in isolation.
At the moment I have the In summary the WLC and GBA properly operate independently, but they do not communicate via radius. Any help appreciated thanks It seems that you use ACS 5.0 without tasks. For your information, the version of the product is now up to 5.2 and 5.3 ACS should soon be released I recall there was a problem with ACS 5.0 with WLC operations that has been resolved in patch for 5.0 I'm not sure of the specific CDETS but can be: CSCsy17858 Any manipulation of Tunnel-Type & Tunnel-Client-Endpoint uploading incorrect ACS 5.0 has a rollup with all the patches being accumulated approach My recommendation would be to download the patch 8 for ACS 5.0: 5.0.0.21.8 Patch can be downloaded from CEC To install a patch set a repository on ACS (cumulative patches are larger than 32 MB, you can not use TFTP to it), copy the patch file in the repository, click ACS CLI: # acs patch installs repository RADIUS does not not on Cisco ACS SE v4.1 (1) Hello I have a CiscoSecure ACS version 4.1 (1) build 23. I can't configure the Cisco ACS for granular control of access router. I have a Netopia Router that is configured to use RADIUS to authenticate remotely for a telnet connection. The router sends the request to access the Cisco ACS SE RADIUS and a sniff on the side of the ACS shows the application of GBA, but I see no response from the ACS. RADIUS authentication to work with a Windows 2003 server. I configured an AAA client and a user of the ACS and use the default group. I use IETF RADIUS. Should what attributes I configure. In Windows, I use Service Type framed and Framed-Protocol PPP. This does not work with the Cisco ACS SE. Nothing shows up in the newspapers. It shouldn't be so difficult, but for some reason I can't make it work. Thanks for any help. Jutta Kullmann Jutta, Good to know it works very well. Please mark this thread as solved so other can benefit from. Kind regards ~ JG Cisco ACS 4.2: The most important to back up files? Dear Sir Can you tell me what are the most important files to back up in the Cisco ACS directory? Currently, I am only backup (with Symantec Backup Exec): C:\Program Files\CiscoSecure ACS v4.2\CSAuth\System backups * But, I would like to know if my server crash, can I restore the entire configuration with the files listed in the directory below? (Users, groups, groups of devices, AD, mapping, users, groups,...) * The Cisco ACS there change in the Windows registry? * Is it necessary to reinstall the Cisco ACS, if I need to put in an emergency on a new server? I guess Yes, because the installation creates services, etc. I ask this question because it takes time to install the patches... * Or, can I save all the Cisco ACS directory... On a new server, install the Cisco ACS and restore the backup? Thank you very much for giving me your experience about it. Kind regards You should back up the files that come from ACS backups, i.e. System configuration > backup GBA, the location that is specified in this section. And the default location is the one that already save for example "C:\Program Files\CiscoSecure ACS v4.2\CSAuth\System backups" In case you are required to host ACS on a new server, you would be required to re - install the complete application of the CSA and then simply take the last backup and restore in the newly installed ACS. It will be to restore everything users, group etc. to etc. of the external database mappings. When you install ACS on a new server, then make sure that if you run them Services ACS with a service account (this is required for the authentication of the window according to your requirement), you would be required to run new services with this account too, and which may require that go you through the following documentation. Kind regards Prem Please rate if this can help! Selection rule for the 5.2 Cisco ACS Service Hello dear, I'm trying to configure the Cisco ACS 5.2 to Dot1x of authentication for clients on windows 7 & windows XP, I did all the steps but I could not create Service rule, it gives me an error message that you can see in the attached screenshot. After that I specify the allowed protocols it gives me the choice to choose the choice of identity and the is ' t it give me this error. your help is very appreciated. Kind regards Ibrahim Try another browser like Hussam suggested and let us know the results. I updated FireFox to 15.0.1 and now I am not able to manipulate many parameters with ACS 5.3 If different browsers show the same question, I would say that you restart the machine (physical or virtual) completely and try again. It is also best to upgrade to the latest patch, if this is not already the case. Greetings, Amjad Rating of useful answers is more useful to say "thank you". How to restore the password on Cisco ACS 5.4 Hello! Try to restore the Cisco ACS 5.4 password installed on vmware. Where can I get the password recovery DVDs? There is no software in the list on the site. TAC may provide to you. You will need to open a folder and the application. HTH Cisco ACS and the domain controller Hello We are currently using the Cisco ACS 3.2.3.11 solution engine and using a Windows domain as a remote agent controller. We now have the ACS to 4.1 1. do I need to upgrade the remote agent on the domain controller as well? 2. any computer on the network can be used as a Distribution Server? 3. after an initial backup and upgrade then to 3.3.3.3 I make another backup before the upgrade to 4.1? You can use any PC in the network as a Distribution Server. How can I use Cisco ACS to save Shell commands Hi guys, pleeeease how can I configure Cisco ACS to do command authorization on my Cisco 3660 router. I get the accounting logs and authentication but no newspaper that show orders issued by users - shell and it's the most important paper that I need. I read materails and download articles on the site of Cisco... but the thing is still does not give me the papers. I have these lines on my router: ... AAA authorization config-commands AAA authorization exec default group Ganymede +. AAA authorization commands 15 default authenticated if AAA authorization network default group Ganymede +. ... It's funny, when I turn on debugging of the authorization of the AAA on the router, it shows me every command being sent by the user on the debug log. But nothing shows under Administration TACAC + on the Cisco Secure ACS. What is responsible for this? ***************************************************** I installed the trial version of the Cisco ACS 90 days and made all necessary settings and I have to say I like what I see already. I'm opening moves to recommend the product to purchase. Thank you guys, I got about the features of this ACS software through this forum, keep up the good work. I recommend the software for those who need to have adapted to the management reports Security Audit logs. If I understand what you're asking correctly, the answer is not in the authorization, that it is in accounting. I set up on my routers and send to ACS orders that level 15 privilege users enter on the router. orders accounting AAA 15 by default start-stop Ganymede group. Does Cisco ACS 1113 v4.2 device work with Windows 2008 Hello I have a wireless currently in production infrastructure. All my Cisco LWAP is managed by Cisco WLC. Authentication is done via RADIUS through my device Cisco ACS 1113 running on version 4.2. The Cisco ACS 1113 device communicates with my Windows 2003 Active Directory. Everything is good now. Next month, we plan to update Active Directory from Windows 2003 to Windows 2008? Will be all fine and good, or will it be questions? Please advice kindly. I saw another post in this community that the States https://supportforums.cisco.com/thread/1003597?tstart=0. I am now confused. Help, please. Kind regards RAM + 60122918870 ACS 4.2 does not work with Windows 2008R2. I had a case of TAC open about this, and basically, they told me that I had to switch to 5.2 ACS. I've been doing demonstrations there and it authenticates with Windows2008R2 very well. Cisco ACS 5.2 VMware 'Management' process hangs Hello We recently purchased the Cisco ACS 5.2 VMware must be installed on VMware ESXi 4.1. However, after commissioning the virtual machine with the requirements set out in the Cisco installation guide, GBA is unable to start properly. We don't get messages visible error, but when checking on the process of the CSA, I see that the process of 'management' is suspended in the "initializing" State Any ideas how to solve this problem? Thank you Gilbert ESX 4.1 is not supported with ACS 5.1 The minimum configuration for the virtual machine must be similar to the hardware configuration of the server series CSACS-1120. Table 6-1 lists the minimum system requirements to install ACS 5.2 on a VMware virtual machine. Table 6-1. minimum system requirements CENTRAL PROCESSING UNIT Intel Core2; 2.13 GHz Memory 4 GB OF RAM Hard drives 500 GB of disk storage NIC 1 GB NETWORK interface Hypervisor VMware ESX 3.5 or 4.0 Installation of ACS 5.2 on VMware Kind regards Jousset Windows 8 does not see the hard drive on the Satellite A200 Windows 8 does not see the hard drive on the A200.How to install it? This laptop was good to me and does not know the password. When started, it has a black screen reading "CURRENT password: When my niece (former owner) tries to guess her password and it gets wrong, "password check failed, fatal error... System shutdo Paviliion G7-2340dx: Bluetooth Hello I was wondering if my laptop has bluetooth capabilities? I want to buy a wireless headset and I wanted to just make sure that Thank you. Getting the data center of VirtualMachine with Get-View information HelloY at - it a faster way to get the name of data using Get-View and the viewtype VirtualMachine Center.I found the following: Get-View -ViewType VirtualMachine -filter @{ "name" = "mtl1fsit02" } | Select-Object -Property Name, @{ Label = "GuestOSN This update does not work why? Update f03012Set aiac10 = "WST".f03012 a, f0116 bwhere b.aian8 = a.alan8 and b.aladds = "CA";Order get SQL not properly completed.
Jatin koneSimilar Questions
1. access to the serial port on your PC.
4. When you are prompted, type a pair of IP address/netmask and press ENTER.
5 if necessary, at the prompt of gateway IP address configured, type y to set the IP address of the gateway and press ENTER.
6. at the prompt of gateway IP address, type the IP address of the gateway and press ENTER.
7 at the prompt of the writing MGMT port configuration file, type y and press ENTER to save the configuration file.
Version of this browser is extremely stupid with ACS 5.x, but it shows not all message boxes. It just does not display the page when you click on the link.Virtual Machine requirements
Maybe you are looking for