driver configuration problem

Similar Questions

• Configuration problem?

  I'm new to Labview. I can't connect with 3458A. It works with 34401. I use a USB/GPIB from Agilent 82357 B interface. I have a VEE program that works with the 3458A. I think I have a driver or configuration problem. I am at a total loss, any help would be appreciated.

  I got it to work with the correct command. Thanks for your help. I have much better understand how this works now.

• two drivers of PXI chassis with Configuration problem

  Hello

  I have two PXI chassis. One is PXI 1033 and works perfectly with the NI PXI-5404, 5105, 6509, 1409, installed 8336. The other is 1036 PXI with the PXI-5404 NI, 8366 installed. When I was trying wreath connect, as master 1033, 1036 as slave, I found several problems.

  1. in the Measurement & Automation Explorer, does not have my good guys in 1033. Instead, there is a sign of the Red Cross in bottom right with 6509, 5105, 5404.

  2. I can't find an another 5404 of the 1036. In fact, I can't find 1036 in MAX.

  Update BIOS. My PXI system is already identified under the name 'NOR PXI - 1033 Embedded MXI Express' and Chassis1 is identified as 'NOR PXI 1033'.

  So I made several tests as below:

  1. unscrew the 5404 1036 slave. MAX can configure 2 1036 chassis. Ok. But when I reconnect 5404 in 1036, same result happened as stated above.

  2 uninstall the driver of 5404, so the 5404 in 1033 does not either now. And then reboot again, same result happens again. Cannot detect the 1033 chassis. Other vouchers in 1036 don't work either.

  Please, any suggestion is highly appreciated.

  Sincerely,

  Bin

  Hi Ben,

  This happens sometimes with MXI-Express:

  Error code 12 with MXI-Express

  http://forums.NI.com/T5/PXI/two-PXI-chassis-connection-with-configuration-problem/m-p/1475876#M9033

  In general, you can read this error 12 means on Device Manager:

  Explanation of error codes generated by Device Manager in Windows XP Professional

  http://support.Microsoft.com/kb/310123

  If it was a problem of bandwidth, PCI or PXI side, you could pull a few cards to see if that alleviates the problem, or that the link from Microsoft over the States, you can disable the driver for other cards.

• Configuration problem of the mixture of the regions with and without installation of persistence of the disc causing the JSONFormatter to fail

  I have trouble setting my local setup correctly with a mixture of regions with different configuration of persistence of disc.  Is a configuration problem on my end or a bug in GemFire and/or Spring GemFire data?

  The configuration of my work is as follows:

  < gfe: replicated-region id = "replicatedRegion" cache-ref = "gemfireCache" disk-store-ref = "overflowOnlyDiskstore" persistent = "false" >

  < gfe:eviction type = threshold "HEAP_PERCENTAGE" = "90" action = "OVERFLOW_TO_DISK" / >

  < / gfe: replicated-region >

  < gfe:local - region id = "localRegion" cache-ref = "gemfireCache" / >

  
  

  With the above configuration, I can successfully call JSONFormatter.fromJSON (json) and get a reference to a PdxInstance object.  However, when I kinda modify configuration to enable the persistence of drive on one of the regions, the call to JSONFormatter.fromJSON (json) fails.  The change is as follows:

  
  

  < gfe:local - region id = "localRegion" cache-ref = "gemfireCache" persistent = "true" disk-store-ref = "persistOverflowDiskstore"/ >

  Without any additional modification, the following error starts occurring:

  com.gemstone.gemfire.pdx.JSONFormatterException: could not parse JSON document: [Source: java.io.StringReader@5549f0e, line: column 26,: 6]

  at com.gemstone.gemfire.pdx.JSONFormatter.fromJSON(JSONFormatter.java:66)

  ...

  Caused by: com.gemstone.gemfire.pdx.PdxInitializationException: The PDX metadata must be persistent in a limb that has persisted data. See CacheFactory.setPdxPersistent.

  at com.gemstone.gemfire.pdx.internal.PeerTypeRegistration.checkAllowed(PeerTypeRegistration.java:531)

  at com.gemstone.gemfire.pdx.internal.PeerTypeRegistration.verifyConfiguration(PeerTypeRegistration.java:515)

  ...

  Note that it is breaking while I try to get a reference to a PdxInstance, and if the code has not yet arrived at the point where I place a PdxInstance object in a region.

  Thanks for any help in advance.

  Hello

  JSONFormatter PDX uses as is the serialization mechanism from the Gemfire cache. As indicators of error, you must have your persistent PDX meta-data when you use PDX with an area that itself is persistent. Adjust your configuration as follows:

  It will use a default for PDX record store, but you can also use a specific store if you wish.

  When you use PDX, a "PDXType" is created for each class serialized with PDX and this type id is stored with the data in the region. If this region is persistent, then the PDXType, associated with this object must also be kept.

  -Jens

• HP 802. 11b / g wireless network: HP 802. 11b / g wireless network adapter driver installation problems

  After installation of Windows 10 does not work me wi - fi, I can not find a compatible driver. The search I found one, but it gives me driver installation problems

  Hello @fede95,

  Thanks for posting on the Forum of HP and welcome!

  I'd be happy to help you with wireless driver problems you encounter since the upgrade to Windows 10.

  I will need to know your product number. You can follow the steps here - http://ow.ly/XnZL300dhzo - to find.

  I'm looking forward to hear back and work towards the resolution of this problem.

  If these steps solved your problem, please click "Accept as a Solution." You can also click on the "congratulations, Thumbs Up" on the right to say "thank you!"

• URGENT... Driver video problem Check

  140105 URGENT...  Driver video problem Check
   
  (will take other ideas on what to do for video problem)
  performance of device drivers fix security
   
  my video seems to be a xp machine.
  When restoring from my pc to an earlier date, it seemed to alleviate the problem.
  When I boot in safe mode, I have a video perfect (with the exception of the size of the objects).
  When I reboot, screens of washing washing & microsoft come up, when get to xp blue light / logon screen it goes black.

  What is this 'supposed' to have a problem with?
   
  is there a way to get a proper driver download?
  and: is there a utility to repair the files without destroying the data...
  Thank you

  have: windows xp3 sp3, viewsonic va800 monitor

  I went to the site of the Lim.  think that was part of the problem with saw to no support.  sent them an email / current.

  check microsoft to the drivers FRO viewsonic va800, except if someone can help with a good method of downloading drivers before hand.

  Hi Dave,.
  I could be wrong, but "Viewsonic va800" resembles a monitor?  I think that you need to update the drivers for your graphics card.  In Device Manager, look at "Graphics cards" (that's what they are called in Windows7, could be something different in xp...).

  Take a look at this site for more information: http://pcsupport.about.com/od/fixtheproblem/ht/updatedriverxp.htm

  Because every PC is different (a different material) you're not going to find specific instructions, I'm afraid).

  Hope that helps.
  See you soon
  Rich

• "When try to turn on my computer: Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid

  Original title: configuration of the CRA

  Hi, I got this message then try to turn on my computer:

  "Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid. "Please check the Windows documentation about the configuration option BOW and your reference manuals of the equipment for more information.

  can someone help me?

  Hi sugenghariyono,

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  ·         Are you able to boot to the desktop?

  Follow the steps in the article.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  For reference:

  Advanced Troubleshooting for General startup problems in Windows XP

• Network Configuration problem

  Hello:

  Since last week, when I click on an icon, for example, the Page Home/Windows 7 does not come on the screen.  Instead, warning to appear at the top of the screen saying... Problem with Internet connection or Network Configuration problem.  After 5 minutes, or later, however, the screen came, but it is very slow to open web pages.

  This problem occurs most often during the night, however for the last two days, sometimes also during the day.

  Until this problem started out of blue, wireless connection with Comcast was very smooth-ride,... instantamously the homepage of popping up.

  Hints on this would be greatly appreciated.

  Thank you

  This sounds like a problem with your Comcast service. In the United Kingdom, I would suggest that you run a speed test on your connection speed. You can get no doubt do the same wherever you are. While it could be the quality of your line, the calendar offers it's the volume of traffic from when children arrive home from school until they go to bed.

  You could compare notes with other Comcast customers.

  http://forums.Comcast.NET/

  Hope this helps, Gerry Cornell

• NAS 200 - two drives configured as a big disks (JBOD/LVM)

  Hello

  My first drive is full and so I put a second in my nas200.

  When I select:

  Two drives configured as a big disks (JBOD/LVM)

  My first drive will lose all the data?

  After that I backed up my data, I have merged the two discs.
  All data, users and directories have been removed.
  Thanks for the replies.
  Good bye

• Configuration problem EM on 12 c OEM

  I started working on a new client, who was a repository of grid 12 c Setup program, and they have restarted a server for maintenance. When I tried to enter emctl start agent, I received the following.

  The MA Configuration problem. /U01/app/Oracle/product/11.2.0.3/dbhome_1/servername.domain.com_oem not found.

  Is there a way to create this file? is or if I should use emca, possible that I can perform a 'regeneration' without changing the initial configuration?

  Thanks everyone, I solved the problem. I made a backup of my old profiles.xml, created a void with just header and footer information, and everything started upward normally, thank you again!

• OC4J Configuration problem. $OH / OC4J_DBConsole_IPADDR_db not found.

  Hi all

  I have a new installation of Oracle 11 g 2 m4.

  I tried several times creating dbconsole, ensuring that the environment variables are defined property and also in the response file, specifically ORACLE_HOSTNAME is set correctly.

  The emca - config... returns with success,

  but in the newspaper, it shows me the URL to control db being in the form of https:// < hostname >: 5500/em

  Under OracleHome, I have a directory in the form of < hostname > dbcontrol Private

  Although my departure db control fails with above message.

  emctl start dbconsole

  "OC4J Configuration problem. $OH / OC4J_DBConsole_IPADDR_db not found. »

  My question is since emca creates the control with the format https:// < hostname >: 5500/em , and it is properly configured in OracleHome, why "emctl" refers to IPADDR and allows me not to start dbcontrol?

  Thank you

  DP

  What is the name OS & version?

  what OS command under report

  hostanme

  can you do successfully as below

  Ping

  Ping

• Photoshop CS6 configuration problem, code 16

  So I have a PC and I come again Mac Pro 2 days (it is a little difficult of is used), and my Mom took a tech shop any to download all of these programs for me. But when I tried to open Photoshop this configuration problem keeps popping up and the code is 16. I don't know how to fix it, please help! (Also if someone could elaborate on their answer that would be great, I'm really not very good with computers).

  http://helpx.Adobe.com/x-productkb/policy-pricing/configuration-error-CS5.html

• OEM EM Configuration problem.

  Hello
  
  I created the database using YES. End of the installation, he showed OEM url
  Enterprise Manager 10g Database Control URL:
  http://RHEL5.myserver:1158 / em
  
  When I try to connect oem, I couldn't. then I checked
  
  * $ emctl status *.
  TZ defined on Asia/Calcutta
  The MA Configuration problem. /U01/app/Oracle/product/10.2.0/Db_1/RHEL5.myserver_TSH1 not found.
  
  
  * $ emctl start dbconsole *.
  
  TZ defined on Asia/Calcutta
  Oracle Enterprise Manager 10 g Database Control Release 10.2.0.1.0
  Copyright (c) 1996, 2005 Oracle Corporation.  All rights reserved.
  http://RHEL5.myserver:1158 / console/em/aboutApplication
  from Oracle Enterprise Manager 10 g Database Control... started.
  Logs are generated in the /u01/app/oracle/product/10.2.0/db_1/rhel5.myserver_orcl/sysman/log directory
  
  
  1. may I know, YES even created OEM, why I can't connect?
  2. I do not understand: the MA Configuration problem. /U01/app/Oracle/product/10.2.0/Db_1/RHEL5.myserver_TSH1 not found.
  
  My db_name is: orcl
  the product is 10. 2.0
  OS: redhat
  
  Thanks in advance...

  After you start the DB console, use a browser to access the console on the URL indicated in the output of the command "emctl start dbconsole":

  For example, go to URL https://rhel5.myserver:1158 / em

  In addition, if you have multiple databases to monitor/manage. Consider using MS Cloud Control.

  Doc on Cloud Control is available here:
  http://docs.Oracle.com/CD/E24628_01/index.htm

• VMDirectpath configuration problems.

  Well, I think I Passthrough (VMDirectpath) configuration problems. I use vSphere VMware ESX, 4.0.0.

  I tried to configue passthrough, so I checked Configuration-Hardware-Advanced setting and I don't found "no device currently activated for passthrough.

  I clicked on "configuration Passthrough.. ' and tick"Mark of Passthrough devices"then I found all USB devices are passthrough capable but not running in passthrough mode and PCI/PCI bridges are not able to passthrough.

  After ignoring the warnig message ('vmnic0' assignment, which used by the virtual switch 'vSwitch0' for passthrough access can make the inaccessible host and can require a lot of effort to cancel.), I marked as the relay device, and of course I've known the significant effort to cancel. :$

  I could not access the server, and the start was now available for some time.

  What I want to really know is.

  I'm looking for the correct devices for passthrough

  and what was the Passthrough configuration problem.

  Is this Client vs server problem? or materials (such as the version of the kernel or CPU specifications)?

  Anyone knows the solution or has any advice, please help me.

  Thank you.

  Kwangwon Chae

  Hi kwangwon, it seems like you just a physical network adapter on the host ESX (i) and is used by the vSwitch0 (at installation time is created inteface vswif0 here commonly called console port or management service), that's why you get this 'warning' when you try to set this for VMDirectpath pci device and also, that's why you lose your connection to your host because it can no longer be used by your esx server.

  Kind regards.

  If you find this information useful, please give points to "correct" / "useful."

  My blog virtualizacion you en idioma

• EM configuration problem

  Helllo all,.
  
  I am unabe to open OEM.
  while checking the status of the following message.
  I use win7.
  
  
  
  C:\Users\User > EMCTL STATUS
  The MA Configuration problem. C:\app\user\product\11.2.0\dbhome_1/user-TOSH_prod3 not
  found t.
  
  Please advice

  Hello

  The decline in the repo was not successful, it seems. Why not try to file correctly then continue with leisure.

  concerning