DRIVER_IRQL_NOT_LESS_OR_EQUAL (tcpip.sys) Blue error screen to restart the computer
Hello
I recently bought a new laptop refurbished and I have a problem from the appointment. I bought the laptop yesterday. It's a Sony Vaio Fit 15 E, 64 bit with 8 pre-installed Windows. There are times when I get a blue screen with a sad face that just explains that an error has occurred, the error is: DRIVER_IRQL_NOT_LESS_OR_EQUAL (tcpip.sys). It mainly occurs when I try to use torrent software. I did the excessive thread lurking on the various sites looking for a solution to the problem but nothing I try works.
Some forums have said it is this need to updated drivers network card, but when I check updates told me I have the latest drivers. Other forums suggest that this is a problem with McAfee drivers interfere. McAfee has been pre-installed, but I uninstalled all McAfee products manually and then used Development to remove all McAfee software are still hiding on the laptop which, according to him, has worked. I installed Malwarebytes and AVG also and I tried to remove them and try again to see if it was the issue, but even when deleted the error kept appearing and the computer crashing.
I don't really know what is the cause and every time I try a suggestion from other sites they do not solve the problem. I downloaded the minidumps on my laptop here down, however I don't know how to read or do analysis. Is there someone who would be able to help me?
The Minidump files: https://drive.google.com/folderview?id=0B3gAlOZ6dvu8MG5LWjh5cHFQOG8&usp=drive_web
Thank you
Roisin
Hi Roisin,
All attached files of the DMP are the bug check DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1) .
This indicates that a kernel-mode driver attempted to access pageable memory with a high IRQL.
A driver tried to access a pageable (or that is completely invalid) address while the IRQL was too high. This bug check is usually caused by drivers who used a wrong address.
-FAILURE_BUCKET_ID: X64_0xD1_tcpip + 138ac3
^^ tcpip.sys is labeled as the fault, but it is not the real cause of the accident. There is something of cause of NETBIOS conflicts. In addition to debugging shows the crash of coherent process following each crash dump:
-Nom_processus: mbamservice.exe
^^ Malwarebytes.
That being said, AVG is at the origin of conflicts with Malwarebytes. Regardless of whether you're a suite antivirus and the other is antimalware, both are active protection and try to install their interceptors to the kernel for analyzing critical data. Because of these two active protection software tries to do this, the conflicts are happening.
--------------------
Remove and replace AVG with built-in Windows Defender from Windows 8 for temporary troubleshooting purposes, as it is in conflict with Malwarebytes:
-AVG removal http://www.Avg.com/us-en/utilities
Windows Defender (how put on after the withdrawal)- http://www.eightforums.com/tutorials/21962-Windows-Defender-turn-off-Windows-8-a.html
Kind regards
Patrick
Tags: Windows
Similar Questions
-
I get the same code at startup until you mean? Stop: 0x0000007B % 20(0XF789E524,0XC0000034,0X00000000,0X00000000)
0x7B bug check code
http://msdn.Microsoft.com/en-us/library/ff559218 (v = VS. 85) .aspxThe boots are sometimes successful and sometimes not?
If you you do not want to lose any data, make sure you take a backup on removable media before trying to solve the problem.
Select Start, run, type cmd and press ENTER. Type "chkdsk c: /f /r" without the quotes and press ENTER. Make sure you include the spaces indicated. Enter Y when asked if you want to run chkdsk on restart the computer. Quit and then restart the computer.
Marking bad sectors on a hard disk takes time so be patient. Delimiting does not repair a defective sector. He places pointers to the reader by saying the system not to read or write to these areas that have been damaged.
If the number of defective sectors continued to increase after using the procedure above several times, then you should replace the disk. If an important system file is written to a bad sector, you can corrupt the registry hives and lose the entire contents of the disc.
However if have run chkdsk you not see more new bad sectors, then the reader can work for you for years.
What is your computer brand and model? You have a Windows XP CD? It's a detail. Generic OEM or OEM brand copy. Suppliers of computers brand often give users a copy of Windows to a recovery partition. That applies to you?
Take a look in the system log in the errors and warnings event viewer and post here the copies. Do not post on more than 48 hours ago.
You can access event viewer by selecting Start, Control Panel, administrative tools, and Event Viewer. When searching for the meaning of the error, information about the event ID, Source and Description are important.
A tip for posting copies of error reports! Run Event Viewer and double-click the error you want to copy. You will see a button resembling two pages. Click on the button and close Event Viewer. This places a copy of the report to your Clipboard. Paste it into the body of your message. Make sure that it is the first dough right out of the event viewer.
-
How to stop the blue e screen to start the computer and also if you try to download anything
Remember - this is a public forum so never post private information such as numbers of mail or telephone!
How to stop the blue e screen to start the computer and also if you try to download anything:
- You have problems with programs
- Error messages
- Recent changes to your computer
- What you have already tried to solve the problem
Hello
We need numbers BBCode or Code to stop the bluescreens and utilities below will help you
provide us information. Also the methods here can help you solve the bluescreens.Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during "blue screen of death," collisions
http://www.NirSoft.NET/utils/blue_screen_view.html
Displays information on all the "crash" of a table - freeBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob - bicycle - Mark Twain said it is good. -
Blue error screen when indexing the files on Vista computer
Original title: Problem Event Name:_BlueScreen__ OS Version:_6.0.6002.2.2.0.768.3__ Locale ID:_1033__
BCCode: f4
BCP1: 00000003
BCP2: 872E2D90
BCP3: 872E2EDC
BCP4: 81E33710
OS version: 6_0_6002
Service Pack: 2_0
Product: 768_1
Before I tear off my hard drive and throw it out the window, please tell me I can recover from this error. The above error when I try to rebuild my Index. I regularly get messages "index has stopped working". I select the indexer rebuild to the original configuration. He tried to do, but stopped after the indexing of files about 1700, restarted, and then returned with the above event. I had several problems with my OS for a few days. I have run chkdsk and chkdsk/r several times. I use Norton 360, analysis tell me that all files are up to date, Windows update is performed regularly and is up to date. I was initially received an error "parameter has exceeded its normal range" train SMART. I disabled this option considered, but service to have problems with my system. Everything seems to work okay in safe mode, where I am now. I am at a loss. I have a recovery partition on my drive, but did not know what options to use. I have the installation CD Vista too, but avoided to reinstall, have done this before for another question. For any help or suggestion will be greatly appreciated. Please see my other post earlier this week, I was only partially successful with this process. Thank you very much!
Hello
If a PC remove all power to the system:
Check and replace the cards, memory and cables (at both ends) actually remove and replace
-do not just tight. Memory could be the problem, so if you have more than 1 stick swap
in and out to see if the problem follows a stick or try the new memory. How to test
memory in the next message.-------------------------------------------------------------------------------------------------------
Pick up the pieces after a computer crash - includes "what to do if Windows doesn't.
start correctly'.
http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crashCheck this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65================================================================
BCCode: F4 0x000000F4
Check and reinstall the cards memory and cables (at both ends where possible) actually remove and
replace - do not just tight. On a laptop computer on all you can do is reinstall the memory and possibly check
the contacts/connection to the hard drive. Memory could be the problem, so if you have more than 1
stick swap them in and out to see if the problem follows a stick or try the new memory. Antivirus/anti-
spyware/security programs have been known to cause or have a role in this matter.More general patch updates day and low level chipset BIOS drivers and other software to control.
Also check wiring for hard drive.======================================================
Bug Check 0xF4: CRITICAL_OBJECT_TERMINATION
CRITICAL_OBJECT_TERMINATION bug control has a value of 0x000000F4. This indicates that a process or thread crucial to system operation has unexpectedly is released or ended.
Important info if you received a STOP Code
If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.
If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.
These actions could prevent a mistake like this does not happen:
- Download and install updates for your computer from Windows Update device drivers.
- Scan your computer for computer viruses.
- Check your hard drive for errors.
CRITICAL_OBJECT_TERMINATION parameters
The following settings are displayed on the blue screen.
Parameter Description 1
The Terminal object type:
0 x 3 : Process of
0 x 6 : Thread
2
The endpoint object
3
The name of the process image file
4
Pointer to a string ASCII containing an explanatory message
Cause
Several processes and threads are necessary to the functioning of the system. As they are completed for some reason, the system can no longer function.
BCCode: F4 0x000000F4<-- read="" this="">
* 1241.html http://www.faultwire.com/solutions-fatal_error/A-process-or-thread-crucial-to-System-Operation-has-0x000000F4------------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard event viewer
Windows. TIP - Options - Advanced filter allows you to see a time rather
of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.htmlHere are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during ' blue screen of the.
http://www.NirSoft.NET/utils/blue_screen_view.html
death ' crashes and displays information about all accidents of a table.
FreeBlueScreens many are caused by drivers of old or damaged, in particular the video drivers
However, there are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Does not work
tell all possible driver issues).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
"blue error screen", while using the web camera program
Original title: available RAM
I need 256 and I get a blue error screen when I try to run the program for a Logitech webcam. How can I determine the amount of RAM available on my computer?
Hi Bauerwoods,
- Did you the latest changes on the computer?
- What is the error message on blue screen?
- What is the name of the program that caused the blue screen on the computer?
- What is the model number of the Logitech webcam?
See the articles below and check if it helps.
How to set performance options in Windows XP
http://support.Microsoft.com/kb/308417
RAM: Add memory to your computer
-
Blue error screen associated with the card wireless mu?
Hello
I have problem of thing for about 6 months, while surfing the net, just the blue screen and restart windows.
the error message was:
DRIVER_IRQL_NOT_LESS_OR_EQUAL netio.sysfirst time I had this problem I have if it was my wireless card so I downloaded the latest driver available for it.
and I think it worked, but then it comes back once in a while, and my laptop restarts for 1 or 2 times a day, but since yesterday, blue sreen remembrance come more often (about 10 times now)
I have not install or uninstall a software or a hardware recently, I uninstalled the driver for the wireless card and reinstalle reinstalled again, does not solve the problem.
I thought it might be the problem of internet, uninstalled, download manager, does not solve the problem.
I use windows 8, Firefox, chrome, ie Web browser and all updated.
my wireless card is Realtek RTL8187 Wireless 802. 11b / g 54Mbps USB 2.0
It is a link to my latest in information about errors in the minidump folder using the program called bluescreenview.
Asdon
No worries.
All of these related Netio.sys. More often than not when it comes so the underlying cause is in fact the request of malicious software installed. In your case, it's Avira & the remnants of Symantec.
I'm removing the two and use the built in Defender in his place
Symantec is a common cause of BSOD.Use it to Norton 360 http://Symantec.pcperformancetools.com/Norton-360-how-to-uninstall.html
Other former pilots who need updatewdcsam64.sys 2008-04-16 03:39:08
ISODrv64.sys 2009-02-10 04:22:18
RTL8187.sys 12/09/2009 04:16:39
BazisVirtualCDBus.sys 08/08/2011 13:11:12
CLVirtualDrive.sys 2011-12-26 08:26:47 -
Satellite A60 - 102 - Blue error screen appears on the screen and the system to reboot
Error on blue screen sometimes display on screen and reboot system
How can solve this problem
Hello
BSOD code, you get exactly?
What operating system you are using?Maybe it's a driver problem. Have you checked for yellow exclamation marks Device Manager?
You can start in safe mode?
-
Satellite L675D: Blue error screen after upgrading to Windows 8
Hello
I recently updated my laptop to Windows 8 Toshiba and whenever I use it, after 5-10 minutes, I get a page of the Blue error screen and restart the laptop.
The problem is really annoying.
I discovered that if I plug the battery charger, the phone works normally, but I want to solve the problem correctly.
What should I do?
I m wondering about your model of laptop. What cell phone do you have exactly?
Regarding your question:
I would like to get this right, with the battery it works ok, but when the AC adapter is plugged, it crashes?What happens when you connect the front adapter from the laptop would be turned on?
How have you installed the Windows 8? Move the laptop Win 7 to Win 8 or have you installed Windows 8 clean system?
Are installed all the drivers Toshiba Windows 8?Another idea:
Go to Windows 8 Device Manager and uninstall the device called compatible ACPI control method battery
Restart the machine and check how it works. -
When you start to print on the hp 6100 the computer stops and a blue error screen
Starts to print on the hp 6100 the computer when to stop an a blue error screen appears, and the computer must be restarted? Help this is driving me nuts.
Hi William,.
Do you receive an error message or error code?
Blue screen can be caused by hardware and software issues.
Try the following and see if it helps.
Method 1:Try to uninstall and reinstall the printer drivers and check if it helps.
Uninstall a program: http://windows.microsoft.com/en-US/windows7/Uninstall-or-change-a-program
Install a printer: http://windows.microsoft.com/en-in/windows7/install-a-printer
Download HP drivers and software - specify product name
Method 2:Refer to the steps in the following Microsoft article and check.
Resolve stop (blue screen) errors in Windows 7:http://windows.microsoft.com/en-US/windows7/Resolving-stop-blue-screen-errors-in-Windows-7
Notes:
Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.
When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.
Before you perform the upgrade on the spot, I would recommend you to back your files using windows backup.
Note: I suggest you to provide us with the Mini Dump files to get a better understanding of the issue.Follow the steps to copy the contents of the minidump files:
(a) copy the contents of \Windows\Minidump to another (temporary) location or anywhere on your machine.
(b) zip copy.
(c) attach ZIP archive to your message by using the button (attachments) "trombone".
(d) please upload them to a service like Skydrive file sharing.
You can view the following link to find out how to send the files minidump using Skydrive:
Keep us informed on the status of the issue.
-
Normally when I or my family members arrive in internet is just Facebook or my space, and lately we had a blue screen with a message and restart the computer. I do not install or change anything. blue screens comes every 10 to 30 minutes and restarts each time. This only happens when we are on the internet.
the message to the blue screen goes like this;
_________________________________________________________________________
a problem has been detected and windows has shut down to prevent damage to your computer
Win32k.sys
PAGE_FAULT_IN_NONPAGE_AREA
If this is the first time you've seen this screen
Restart the computer...
the following code gives at the end of the screen
Technical information:
STOP: 0 X 00000050 (0XA2F0A9F8, 0X00000000, 0X00000001, 0X97734DE)
Win32k.sys - address 977304DE Base at 97660000, Datestamp 4A 856629
Collecting data for Crash Dump
_________________________________________________
It is an office of gateway using Windows Vista Edition GT5656 Home Premium
Please advice
Thank you
El Rica
Hello
For information on using BlueScreenView and MyEventViewer to troubleshoot Bluescreens see methods
stated in this thread.-------------------------------------------------------------
Have you recently added any hardware? Have you updated any drivers just before this started? (Check
Panel configuration-updates of Windows to see if all drivers have been updated it there all the time it started)
Main likely culprits are video driver, other great drivers, memory and antivirus/antispyware/security
products could be at fault as well as reader questions.Use the troubleshooter below and refer to the following message to drivers and memory when you get to
These sections and then back to the resolution of the problems according to the needs.BCCode: 50 0 x 00000050
Cause
The BCCode 50 usually occurs after the installation of the installation of a faulty material or failure of
material (usually associated with defective RAM, either main memory, L2 RAM or RAM video cache).Another common cause is a defective system service installation.
Antivirus software can also trigger this error, as can a corrupted NTFS volume.
Solve the problem
Solve a defective hardware problem: If the material has been added to the system recently, remove it to see
If the error recurs. If the hardware failure existing, remove or replace the faulty component. You must run
Diagnostics of material provided by the manufacturer of the system. For more information about these procedures, see the owner
Manual for your computer.Fix a defective system service: Disable the service and confirm that this resolves the error. If so,.
Contact the manufacturer of the system service on a possible update. If the error occurs during the system
startup, restart your computer, and then press F8 at the menu character mode that displays the operating system
choice. In the Windows Advanced Options menu that results, select the last known good Configuration
option. This option is most effective when a pilot or a service is added at a time.Solve a problem of antivirus software: Disable the program and confirm that this resolves the error. If she
is the case, contact the manufacturer of the program about a possible update.Fix a corrupted NTFS volume: Run Chkdsk /f /r to detect and repair disk errors. You must
Restart the system before the start of the analysis of disk on a system partition. If the SCSI hard disk, check for
problems between the SCSI controller and the drive.Finally, check the system log in Event Viewer for additional error messages that might help identify the
device or the driver that generated the error. Disable the cache in memory of the BIOS might also resolve it.
BCCode: 50 0 x 00000050<-- read="">
* 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-------------------------------------------------------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
information on all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Error Windows 8 | DRIVER_IRQL_NOT_LESS_OR_EQUAL (tcpip.sys)
Hello. I recently made a new re - install on my HP Envy m6 to make my PC more smooth, but after that and re - download my content, I get an error when I run some programs. My PC is Windows 8 64-bit, and the error says:
DRIVER_IRQL_NOT_LESS_OR_EQUAL (tcpip.sys)
My minidump files:
http://1drv.Ms/1mI3jFl
http://1drv.Ms/1mI3a4Jhttp://1drv.Ms/1mI3pg7
http://1drv.Ms/1lrJ03Y
http://1drv.Ms/1lrJ1Vq
http://1drv.Ms/1lrJ9nK - compressed files
I've read about it online but do not understand because it seems that everyone had different problems or newspapers. Could someone help me solve my problem?
These accidents were related to the corruption of memory (probably caused by a driver).Please run these tests to check your memory and find which driver is causing the problem.
If you're overclocking (pushing components beyond their design) return you to default at least until the crash is resolved. If you don't know what it is that you're probably not overclocking.
Since then, it is more likely to be a pilot run everything first.1-Driver Verifier (for full instructions, see our wiki here)
If the auditor does not have the issue we move to it.2-Memtest. (You can learn more about running memtest here)
If you cannot start after you have enabled the auditor reboot in safe modeIn Vista & win 7 (F8)
Co-written by JMH3143.
-
Blue error screen Stop 0X0000007E (0XC0000005, 0X8070194F, 0XF78DAC30, 0XF78DA12C) and when ejecting a CD or DVD
Said event system category 102 event 1003 error view
Error 1000007e, parameter1, parameter 2 8070194f, parameter3, parameter4 f78da92c f78dac30 c0000005.
Customer says that has happened for about a year. Don't know it please help
Hello
Use BlueScreenView, MyEventViewer and other methods of troubleshooting BlueScreens
See the responses in this thread - high two answers.----------------------------------------------------------
References to Vista also apply to Windows 7.
This error (7th) is usually a driver problem and display adapter (video) driver is the most suspicious if
It could be others. Antivirus/antispyware/security programs, major software and hardware (heat)
questions can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my
generic methods in the next message and then return to the if necessary troubleshooting tool.Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
spyware/security programs.When you get to the pilot and sections of the memory of the troubleshooter check the following message to
update drivers and memory test and then return to the troubleshooter if necessary.BCCode: 7F 0x0000007E
Cause
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
interpret, you must identify which exception has been generated.Common exception codes are:
0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.
For a complete list of exception codes, see the Ntstatus.h file located in the inc directory
the Microsoft Windows Driver Kit (WDK).Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques.Make sure you have enough disk space.
If a driver is identified in the bug check message, disable the driver or check with the
Reference of the manufacturer for driver updates.
Try changing video cards.
Check with your hardware vendor for updates to the BIOS.
Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
(the address of the exception) must identify the driver or function that caused the problem.If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
has been launched with the /nodebug switch... This problem should occur infrequently. If it occurs repeatedly,
Make sure that a kernel debugger is connected and the system is booted with the/debug switch.In case of exception code 0 x 80000002, the trap frame provides additional information.
If you do not know the specific cause of the exception, consider the following questions:
Hardware incompatibility. Make sure all new hardware that is installed is listed in the
List of Microsoft Windows Marketplace tested products.
Service system or driver faulty device. A service driver or defective peripheral system can be
responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
and IRQ conflicts can also generate this error.
If a driver is listed by name in the bug check message, disable or remove that driver. Disable
or remove drivers or services that have been recently added. If the error occurs during startup
sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
in Safe Mode, you must start the computer by using the Recovery Console to access the file.If the problem is associated with Win32k.sys, the source of the error may be a third remote
control program. If this software is installed, you can remove the boot of the computer service
by using the Recovery Console, and then by removing the offending system service file.Check the system log in Event Viewer for additional error messages that might help identify the
device or the driver that generated the bug check 0x7E.You can also disable memory cache BIOS may try to resolve the error. You should also
Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
For more information about these procedures, see the manual of your computer.The error that generates this message may occur after the first reboot during Windows Setup, or
Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
space, reduce the number of files on the disk drive hard target. Find and delete any temporary
the files that you do not have to have files hidden Internet, backup application and .chk files files that
contain fragments of file saved to disk scans. You can also use another hard drive with more drive
free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.BCCode: 7F 0x0000007E<-- read="">
* 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E--------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard event viewer
Windows. TIP - Options - Advanced filter allows you to see a time rather
of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.htmlHere are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during ' blue screen of the.
http://www.NirSoft.NET/utils/blue_screen_view.html
death ' crashes and displays information about all accidents of a table.
FreeBlueScreens many are caused by drivers of old or damaged, in particular the video drivers
However, there are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Does not work
tell all possible driver issues).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
DRIVER_IRQL_NOT_LESS_OR_EQUAL (tcpip.sys) crash of Windows 8
Hello
I am running Windows 8 on my laptop and have had to face blue screen crashes quite frequently during the past two weeks with error DRIVER_IRQL_NOT_LESS_OR_EQUAL (tcpip.sys) . Here is the link to my system minidump files. Please guide me on the Bill of lading.
https://onedrive.live.com/?CID=081483B437F58824&ID=81483B437F58824%21105
Errors that you encounter is perhaps having two-thirds in real time an installed anti-virus software, Norton and Kaspersky.
Can you try uninstalling Norton and Kaspersky and see if error fix.
Then reinstall Norton or Kaspersky, but not both, using the most recent version or just use the firewall and antivirus integrated Windows 8 (Windows Defender).
-
Here is the full error:
Stop: 0 x 00000024 (0 x 00190203, 0x88bc3390, 0xc0000102, 0x00000000)
Whenever the machine is restarted, ^ this number above changes of carrot. all others remain the same.
BIOS load properly and detect all need too.
have you tried the following:
I tried every avaible selection:
Safe mode
Safe mode with networking
Safe mode with CMD
Last known configuration
Start WIndows normally
Select VGA
Enable Boot logging
Disable the automatic restart in the event of system failureDebug mode
Directory Services restore ModeRecovery Console
.. .and when I than windows loading screen, I'm going in the restart of the bearing. When starting in safe mode, the list of pilots begins to scroll and always stops in the AVGIDSEH.sys
System:
Toshiba Satellite A-75
WIndows XP Home Edition
Fully updated with Svc Pk 3
HITACHI Travelstar hard drive 80 gigHistory:
When the first blue screen hit a week ago, I immediately rebooted in safe mode (windows always loaded then) and conducted an audit by virus with AVG. Then, I updated my Zone Alarm Firewall to the latest version and restarted. There was no sign of the problems that were to come. The next day, I did a little research to see that this error 0 x 00000024 indicates a corrupted registry or the NTFS loader file, among other things. Recommendations included disabling antivirus and programs bad-ware like Ad-Aware, or recently installed programs whose drivers may be at fault. I proceeded to the services.msc and disabled ZoneAlarm both AdAware, then restart. Windows has not been loaded since then this stop only error message I get now.
I did a test of surface of disc with a utility of the UBCD and negative (found no errors) so I guess that the disk is physically very well. Also, re-installed memory that shows no sign of physical goods or damage.
The laptop is a Toshiba Satellite and the folks at Toshiba have no respect for my data. They continue with option 1... Re-install windows. I'm not surprised that in the past they have never really been useful and stood by their products, that's why all the customer complaints.
First of all I need a program utility loader initialization that will allow me to run chkdsk as diagnostic utilities. Please offer your expertise in this area.
First, start in the XP Recovery Console and running a chkdsk/r.
The question was preceded by a loss of power, aborted reboot or abnormal termination? (This includes the plug pulling, buttons power and removing the battery).
These can cause corruption in the file system that must be fixed before you do anything else.
If none of these events occurred (or even if they have not taken place), you must verify the integrity of your file system before anything else (especially "try" things).
There is zero logic to begin to try to begin to try to modify or copy files to a hard drive that has a corrupted file system, so this must first be fixed using the XP chkdsk program and run chkdsk on your hard drives may solve your problem completely.
Use the XP Recovery Console to check the file system on your HARD drive and fix the problems and then try to start your system - this may be all you need to do. Or, you are welcome to just start trying things that might work.
Boot into the Recovery Console Windows using an XP bootable installation CD.
If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.
This is not the same as recovery disks that might have come with the acquisition of the system store.
You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.
The ISO bootable image file you need to download is called:
xp_rec_con. ISO
Download the ISO from here:
http://www.mediafire.com/?ueyyzfymmig
Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:
Here are some instructions for ImgBurn:
http://Forum.ImgBurn.com/index.php?showtopic=61
It would be a good idea to test your bootable CD on a computer running.
You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive. These adjustments are made before Windows tries to load. If you miss it, you will need to restart the system again.
When you start on the CD, follow the instructions:
Press any key to boot from CD...
Installing Windows... going to pronounce.
Press 'R' to enter the Recovery Console.
Select the installation that you want to access (usually 1: C:\WINDOWS)
You may be asked to enter the password (usually empty).
You should be in the folder C:\WINDOWS. It's the same as the
C:\Windows folder that you see in Solution Explorer.
The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.
For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:
A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.
In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.
Running chkdsk is fine, even if he finds no problem. It won't hurt anything to run it.
Assuming your boot drive is C, run the following command:
CHKDSK C: /r
Let chkdsk finish to correct the problems, he could find.
It may take a long time for chkdsk complete or they seem to be "stuck". Be patient. If the HARD drive led blinks always, chkdsk is something. Keep an eye on the amount of the percentage to be sure that it is still making progress. It may even seem to go back sometime.
You must run chkdsk/r again until it finds no error to correct.
Remove the CD, and then type "exit" to exit the RC and restart the computer.
You have not to set the BIOS to boot the disk HARD since the CD won't be.
-
Computer laptop crash with the Blue error screen, locale ID: 4105, BCCode: 4A
Original title: screen blue Usb_bugcode
NEED HELP!
Hello world. Could someone help me please! My phone hangs with the Blue error screen, and it does on a daily basis. I tried to find a solution online but nothing seems to work. Here are the details:
I have a laptop with Windows 7 Edition Lenovo Home premium (Service pack 1). RAM: 4 GB. 64-bit OS. Intel Core i3-3217U CPU @ 1.80 Ghz
And here's the problem:
Signature of the problem:
Problem event name: BlueScreen
OS version: 6.1.7601.2.1.0.768.3
Locale ID: 4105
More information about the problem:
BCCode: 4A
BCP1: 0000000074EC2E09
BCP2: 0000000000000001
BCP3: 0000000000000000
BCP4: FFFFF88002A84B60
OS version: 6_1_7601
Service Pack: 1_0
Product: 768_1
Files helping to describe the problem:
C:\Windows\Minidump\043015-13057-01.dmp
C:\Users\Jimmy\AppData\Local\Temp\WER-855899-0.SysData.XML
Can you please put step by step directions? I'm not very good with computers, and it's really frustrating! I tried to remove and reinstall the usb drivers but that didn't do anything. I read the other threads on the similar error but couldn't find a solution. Thanks for your support!
Could this be something to do with a monitor Samsung that I use?
KD > lmvm sports
start end module name
fffff880 '075da000 fffff880' 075e2000 SPORTS (postponed)
Image path: \? \C:\Windows\system32\Drivers\SSPORT.sys
Image name: SSPORT.sys
Timestamp: Fri Aug 12 00:07:32 2005 (42FBDA34)
Sum: 0000D 894
ImageSize: 00008000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
SSPORT.sys 32-bit Port claim Driver of Samsung Electronics
Samsung ML-1430 series Samsung ML-1430 series USB001 unavailable
You need to update or remove a SSPORT.sys. Zig - zag pointed out to you earlier. Please uninstall this printer and related software.
Type device manager in the search above the Start button box and press ENTER. Find and right-click on the device and click on uninstall from the drop-down list. Restart your computer.
Select the hotkey Windows key + R, type Appwiz.cpl and press ENTER . Place the cursor on Samsung, right-click and select Uninstall from the menu drop down. Restart your computer.
Maybe you are looking for
-
My iPod is frozen on do not disconnect them screen
My iPod is currently blocked on do not disconnect them screen. When it froze, it froze my entire PC and it will not re-start until I unplugged the iPod. In addition, I also tried to reset hard now the buttons play/pause and menu at the same time for
-
Hello I Have (IPAD MINI DEVICE) and have problem In My Memory I have 12.5 GB, and using less of it and A Nofticate it indicates your size will end soon, or something like that I deleted the apps and got 100 MB and after all in the Nofticate come back
-
Unable to get windows update to install the important updates. get the error code 80070013 when you try the automatic and install it manually. It keeps failing one episode a week.
-
printers HP officejet 4500 g510gm
I installed the drivers for printer hp officejet 4500 g510gm. It is officejet 4500 g510gm copy1. I get errors when you try to print. all of the suggestions.
-
Showing in the form of folder icon and cannot access network drive icon
Hi team, The network drive that I drew in my computer using my profile isn't allowing me to access. The network drive icon shows as a folder icon and it says access denied even if I have the permissions to access the file on the server. The server we