DX80 Microphone mode

Similar Questions

• Cisco DX80 Microphone Skype for business

  Hello

  I am facing a problem with a Cisco DX80 model. The device is registered to a CUCM.

  The problem is the microphone when you use Skype for business. Please see the attached picture.

  In the settings for the Skype for business, I can choose the DX80 as speaker and ringtone, but there is no entry for the DX80 microphone like the one for the laptop itself. Like the screen DX80 is also used as control for the laptop off course gives a poor sound quality to the listener. Now, I would like to have the Skype to use the construction of microphones in to the DX80. But it seems not to be possible. We use THIS software for the endpoints DX80.
  I tried to make calls using the DX80 as videoconferencing unit to another system of videoconf Cisco test and here we have no problem with the microphone / sound of the system.
  Of course, the problem is that the microphone can not be chosen in the settings of the Skype for business. I guess it must be possible?

  Best regards
  Brian

  When you have a laptop connected to the DX80 or any end point of telepresence, you can use it as an additional monitor and speaker, the microphone is not connected, and cannot be used with the computer.

• Cannot disable the microphone 1 on SX10 TC7.2.0

  Morning!

  Here, we have a SX10 recently upgraded to TC7.2.0, both microphones work perfectly but the problem we have is we cannot cut the microphone 1 (one internal), we need mute because the codec is somewhat less a screen with speakers to the codec.

  I tried to mute to ' Configuration > system setup > Audio > Microphone Mode 1 input > Off "but not working even after a reboot of the device.

  I tried to disable it in CLI with the command ' xconfiguration Audio input Microphone Mode: Off "but doesn't.

  Can someone give me a hand with this problem?

  Best regards and thanks for your help.

  Hello - I just tested this with free TC7.2.0 software.  The version number is TC7.2.0.aea6651.

  I tested during a call and used the web interface to Configuration > System Configuration > Audio > input Microphone 1 Mode > Off

  I tested it with a table 20 Mic and without.  In both cases, the internal mic has been disabled successfully by the interface web and delivered to market successfully.

  To check this, I typed the two microphones with my fingernail.  The location of the internal MIC is just to the lower right of the camera that you look at the front the SX10. It shares the location with the infrared sensor.

  I could easily hear the tapping of my nail through the speakers of the other system I was calling.  Disable "Microphone Mode 1:" and I couldn't hear the tapping.  Turn on "Microphone Mode 1:" and I could hear the tapping very well.

  So I think that it works correctly.

• How can you put a DX80 in one phone mode?

  I can't find how to put a DX 80 strictly be phone. Not have access to the applications.

  Take a look at ways of operating within the section customizing DX80 Administrator's Guide, public mode might be what you're looking for.

• Low-power audio turn off mode

  Recorded a few videos in mode low consumption. There is no audio signal in one of them. Low-power audio turn off mode? I'm a new user of iPhone still learning on the dev

  Hello taneikab,

  Thank you for using communities of Apple Support. It is my understanding that videos created on your iPhone in low power Mode are missing audio. I know his is a very important part of videos. I'm here to help get this resolved with you.

  Low power mode disable audio, so you should be able to hear sound on records. I recommend that you test your microphone using the instructions and images in the link below.
  Get help with the microphone on your iPhone, iPad and iPod touch

  If the microphones work, but the problem persists, restart your iPhone. This can solve many unexpected behaviours. Follow the steps below to restart.

  1. Press and hold the sleep/wake button until the Red slider appears.
  2. Drag the slider to turn off your device completely off.
  3. Once the device turns off, press and hold the sleep/wake button again until you see the Apple logo.

  Restart your iPhone, iPad or iPod touch

  Here is some more information on what to expect in low power Mode.
  On iPhone Mode low power on your iPhone

  Have a fantastic day!

• Thunderbolt target Display Mode does not (El Capitan)

  Hello

  I have two iMacs (iMac (21.5 - inch, mi 2011) and (iMac (27 - inch, mid 2011).)) I used sight to connect display mode target without problem with a MF639ZM (cable Apple black Thunderbolt, 2 M).

  I updated both the iMac OS X El Capitan, version 10.11.5 and... surprise! they connect more.

  I already stay the PRAM and SMC several times in the two iMacs. The update of the APP Store purging any discount, I already installed all they.

  In my iMac 21.5 "information from the system has a 25.1 Firmware, Firmware Version 2.1.3 the Thunderbolt Bus microphone Port. State no device connected.

  In my iMac 27 "information system has a 22.1 Firmware, Micro Firmware 2.1.3 the Thunderbolt Bus Port. State no device connected.

  If I connect the Thunderbolt cable the status of the link in the information system change Link Status 0 x 7 to Link Status 0 x 1/0 x 2 both of the iMac.

  If I unplug the Thunderbolt the status of the connection cable in the system information changes in Link Status 0 x 7 in two of the iMac.

  In the Console, if I connect or disconnect the cable Thunderbolt I can see:

  IOThunderboltSwitch < 0 > (0x0): listenerCallback - HPD Thunderbolt package for road port = 0 x 0 = 2 unplug = 1

  IOThunderboltSwitch < 0 > (0x0): listenerCallback - HPD Thunderbolt package for road port = 0 x 0 = 2 unplug = 0

  Thus, it resembles the iMac Thunderbolt ports not work and detect the connection of the cable.

  But... Command + F2 is not target display mode!  (Use all F1, F2. etc. keys as standard function key... is disable under keyboard).

  I'd appreciate any help or support to solve this nightmare.

  Best regards.

  Looks like you've covered all the bases except try a new cable Thunderbolt.

  Use your iMac as a display with the target - Apple Support Display Mode

• Front to the Microphone does not work after last update 9.3.2

  My Siri worked around 26/05/2016 and I updated Memorial weekend. Since that time my front microphone has stopped working. FaceTime, dictated, Siri, voicememos are all just static sounds. But if I plug my headphones, it works very well. I tried something that does not promote Apple, but it was hopeless. I did all the trouble shooting and now awaits a chat representative to help me. This will be my second handset with Apple for the year and 1/2. My first iPhone 6 +, the screen no longer responds and they replaced the whole! Now, it's ridiculous!

  Any help, please! How can I get my FRONT facing speaker WORKS?

  iPhone 6 Plus

  iOS 9.3.1

  64GB

  I'm not sure what you have tried, but the simplest and the first line of defense in these matters is a reboot or a forced reboot:

  Restart your iPhone, iPad or iPod touch - Apple Support

  Aside from that, it COULD still be a hardware problem.  iOS updates can highlight potential problems/mismatches firmware in this mode. What is a refurbished phone?

• iPhone 5 s microphone does not work during phone call

  Hello! My iphone 5s works really well, sensors, speaker, camera, all right. Similarly, the microphone works really well when I make a call using 'whassapp', 'line', etc and I can record video, talking to Siri, using voice memo and once more my microphone works really well. BUT! When I make call and receive phone call my microphone does not work, they do not hear my voice at all. What will happen with my microphone when you use the cell phone call? HELP ME PLEASE!

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

  As a final step, try recovery mode. Turn off your unit, then plug it to your computer with the hold home button. Hold down Home button until you see the logo of iTunes on the screen of your device. After that on your computer, you should see the iTunes window saying that your device needs to be restored to factory settings. Click Restore.

  More info here:

  https://support.Apple.com/en-us/HT201263

  If these steps do not work, contact Apple and ask for help.

  https://www.Apple.com/support/iPhone/contact/

• Camileo Clip as a webcam: how to get the sound from the microphone?

  Hello.
  The * Camileo Clip * might be a nice * webcam * _If there... the sound_ with the video.
  Is it possible to have the * microphone * the task force Camileo Clip when used as a webcam?
  Thanks in advance for your help.

  Hello

  Unfortunately I m not the Camileo Clip owner but according to details that I found on the Web pages, the camcorder can be used as a webcam so I guess you can also record sound by using the Clip as a webcam.
  Usually, you choose the default microphone for recording.

  Maybe you should check the settings in:
  Panel-> Audio-> recording (2nd tab from left) tab

  If the webcam mic would be visible, choose this option by default.

  I also recommend you to check the webcam settings and choose the video mode.

• Set the PC in HFP Mode?

  Hello

  I need to configure the PC as a HFP device, while I am able to communicate with my partner via the pc microphone and speakers.
  Is this possible with the Toshiba SDK and Bluetooth 2.1 + EDR USB - Dongle?
  Maybe someone could give me a link to the documentation or examples in C / c#?

  Thanks for your help.

  Hello

  Can you please explain what you mean by HFP mode?

• FYI: AX100 with Sony ECM - GZ1M Multi Interface microphone

  I took the microphone ECM-GZ1M cannon. My AX100 try to better isolate the sounds from subjects in front of the camera and found an interesting problem. So that the microphone. works in the firearms and zoom modes (and turn it off turn internal mic so it should not be removed from the device), you can set the audio level in the menu. the option is disabled when the microphone. is on. It can be chosen for the internal MIC or an external mic, but not a connected mid.

  It resembles programmed audio assumed that we would use something like the XLR adapter (which has its own level control). If the microphone. works very well with automatic level control, but no manual control is possible (as firmware 3.0; it is not in the list of changes for 3.1 but I have not yet tried).

  
  

• microphone does not work on Skype "app."

  Hello

  I upgraded my laptop Pro Win8 of Win7. I use Skype in Desktop without a problem. However, when I try the app 'Metro', the other party can not hear me. The echo test also gives the same result. There is no option to set the audio mode "app" as being the "desktop" view As I said, the "desktop" version works perfectly. Is this a bug, I can't change any settings to see if the microphone is selected in the "app".

  Thank you

  Roger

  Place the cursor with the mouse to the lower right when the application is open. Move to the top, then click on settings to modify the application settings.

• Satellite A80 is possible to use the microphone as a stereo-in line?

  Hello all, first post here.

  I was handed down a Satellite A80-117 and I'd like to be able to scan a few LPs vinyl with it, but there is only a single audio input and he initially seems to be a mono jack for a microphone.

  HOWEVER, I remember reading that some audio interfaces most recent have inputs 'smart', which can operate as micro either or line level (outputs even, in some cases) and I try to figure out if this is the case with this particular unit.

  I searched Google a fair few and found nothing conclusive. the included documentation does not specify one way or the other, even if it refers to as a "Mic/Line inputs. I have access to Windows XP and Xubuntu on this machine; I was wondering if there could be any utilities/apps that could allow me to switch between the different types of entries, if it's all an option with this particular audio chipset.

  I also tried a few different drivers on the Windows installation, and none of them seems to have provision for types of switch ports.

  So I'll appreciate any help, because I'm at the end of my intelligence now.

  Thanks in advance!

  Hi mate,

  Unfortunately there are no special tools to put as you need. But if it s really a mic/stereo line IN it should automatically mode, depending on which jack plug you.
  A good alternative would be to buy an external sound card that is better in terms of quality and external allows to convert your vinyl to digital content, since an integrated card offers not the recording capabilities as a good external USB card his (entirely digital s..)

  Welcome them

• Satellite A120: Microphone does not work when the power cable is unplugged

  I have a Toshiba Satellite Pro A120, which has just begun to play up...

  I regularly record music of my DJ Mixer in microphone of my laptop entry, recording in Adobe Audition.

  Because the power supply makes a buzzing sound, I can't register with the power cable plugged... If I always record with the unplugged power cable, running off battery.

  I've never had any problems before, but what has caused the problem, I now, was earlier the battery ran out while recording, put the laptop into hibernation mode.

  Since then, I can't register with the power cable disconnected. He recorded only with the cable - which is not a good cause snoring.

  It is not a problem with hearing, because in Windows Vista its implemented the problem proved too. As soon as I unplug the power cable, microphone disappears from view.

  I used to work in IT support, so I'm not a technophobe - but I can't for the life of me works why it would suddenly start to occur, power is not related to the entrance it is micro... !

  One of you lovely people have ideas? I checked power options and the Device Manager to see if theres no hardware issues, but there isn't.

  I also reinstalled my sound card drivers.

  It's strange. I guess you tried a boot cold fresh. Hibernation can sometimes cause problems with the devices.

  Try to update the BIOS.

  If all else fails, you may need to reinstall Windows. (Backup your data and run recovery by holding down the button reset during power on)

• M30X: Problem with standby and hibernation modes

  Hello

  In my M30x, I configured my laptop to Hibernate when near the lid. However, when I turn on the computer after this hibernation, there is a problem with the sound settings - I cannot play any music or cannot use a microphone outside, unless I reboot. If reboot is required, then there is no sense to use this feature of hibernation. Also, sometimes after these Awakenings (turn on after hibernation) my mouse (touchpad) spontaneously turns off. This happens when I plug my pc on TV, then come back and close the cover. There someone experiencing similar problems and can help me? Thanks in advance

  [Edited by: admin on 8 May 05 08:02]

  Hello

  It is not easy to say what can be the cause of this problem. I very often use the hibernation mode and there is no problem that even several applications are open. You have this problem only if the device is connected to the TV or every time after hibernation mode?

  It will also be interesting to know if this occurs after each process of awakening or first several modes of hibernation.