Error 0x800700e1 when copying.

Similar Questions

• error occurred when copying audio streams

  So I bought this product and installed and spent about 2 hours going through the tutorials. Now, I decided to make my first record of the sample of a web-based program. I created a new recording project /, size the window, etc. I click on folder, connect to the application, press END on my keyboard and it shows that savings and then BAM, I get "error encountered during audio stream copy" as a small box to pop up. I have no audio turned on or anything. How can I solve this problem?

  I'm fighting the same exact error. I installed Captivate on my other laptop and it worked fine so I thought well, remove it from the original laptop and see what I can do from there. When I went into the Control Panel - Add/Remove programs I couldn't find Adobe Captivate so I ran a installation, check the Add/Remove programs and now he's here, and when I try now to create a project it works... go figure. Don't know what it was but I did check the sound settings in my control panel of two laptops and both were the same, all that I checked were the same - one worked there isn't. The only difference I've found that the laptop which didn't work had the application was on the Add/Remove window, but I was going to start - programs - Adobe Captivate to start if she should have been there. Re-install and see what happens.

• Error 0x8007045D when copying files from computer to external hard drive

  I am trying to copy some files from my drive HARD outside., but I get this error (error 0x8007045D: the request could not be performed because of an i/o device error).

  I run windows check disk on my external hard drive, I tried to run windows defrag, but it takes too Lowe and cancel (external HARD disk is 1 TB). I download a software defrag and defragmented my hard drive using fast (the software is O & O Defrag). I tried on another computer and got the same error. Is it a hardware problem. Y at - there any possibility to fix it. Thank you for helping

  Hello Nyfixen,

  1. have you changed the permission for the external hard drive or files you are trying to copy?

  2. you have all important data (files) stored on the external hard drive?

  3. are you able to copy the external hard drive to the computer?

  The Autorun.inf could not be a problem for that. It always seems to be a problem of permission for me. Some hard drives have a jumper on them for write protection. You should check the configuration of jumpers, thank you consult the manual that came with the hard drive for permissions.

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-know-before-applying-permissions-to-a-file-or-folder

  Format hard drive:

  Read this article for more information on this:

  http://Windows.Microsoft.com/en-us/Windows7/create-and-format-a-hard-disk-partition

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.

• Error 0x8007045D when copying to NAS

  Hello

  I recently created a NAS using NAS4Free. I formatted a hard drive and was copying on my files, however, once that works well for a few days it now gives me an error (see below) while trying to copy to a file. I tried to google the problem to find a solution, but I had no chance. Is that what I can do or is the hard drive (old) just died?
  "An unexpected error prevents you from copying the file. If you continue to receive this error, you can use the error code to search for help with this problem.
  "Error 0x8007045D: the request could not be preformed because of an i/o device error."
  Thanks for the help!

  Hi Chris_1989_A,

   

  Method-

  I wish you post your question in the TechNet Forums because it caters to an audience of it professionals.
  Check out the link-

  TechNet forums

  Hope this helps!

• Error when copying data from a damaged to a new profile in Windows XP user profile

  Hello

  I think my user profile may be corrupted so I'm trying to create a new profile and copy the Ntuser files anywhere in the new profile by following the instructions in the Article ID: 811151.

  I created two new Admin accounts loged on my old account and connected to one of the new admin accounts.

  When I navigate to C : \Documents and Settings\ Old_Username  there are only two of the three files listed, NTUSER. DAT and Ntuser.dat.LOG, and both are slightly dimmed. When I copy these files and go in C : \Documents and Settings\ New_Username  I get an error saying "cannot copy NTUSER: it is used by another person or program." Close all programs that might be using the file and try again. »

  My home screen tells me that only the new admin account someone connected and when I go into the Task Manager there is no process running with my where ancien_nom_utilisateur, the entire SYSTEM and the new admin account?

  So, what I'm doing wrong, how to fix this and have is my Ntuser.ini file?

  Thank you very much...

  
  

  http://support.Microsoft.com/kb/811151

  Excerpt from the article below (note that it says "except the following files")...

  Press on and hold down the CTRL key while you click each file and subfolder in this folder, except the following files:

  • Ntuser.dat
  • Ntuser.dat.log
  • Ntuser.ini

  If I helped you overcome the "used" problem, you'd probably end the corruption of the copy!

• I get an unknown error message when you try to copy a cassette of my video camera, but the camera connect

  I get an unknown error message when you try to copy a cassette of my video camera, but the camera connect

  If you are running Windows XP... There is a slight chance
  that by running the following command would be the fix:

  Reach... Start / run... and type or copy / paste the following text:

  regsvr32 %windir%\system32\qdv.dll

  Then... Press on... Come in...

  You should see a dialog box stating:

  DllRegisterServer in C:\WINDOWS\system32\qdv.dll successful

  Good luck...

  There is debate on this subject in the following forum:

  Windows Movie Makers Forums
  An unknown error has occurred

• When I try to copy a file to an external device using Windows Explorer I get the following error message: "cannot copy. The directory or file cannot be created. »

  original title: could not copy files

  When I try to copy a file to an external device using Windows Explorer I get the following error message: "cannot copy.  The directory or file cannot be created. "I understand that I may have the physical limit of USB keys for the root directory.  How can I fix it?

  Hi GloriaZF,

  What is the size of your external hard drive and what is the available free space? Open my computer-> right click on the external hard drive-> properties. You will not be able to copy more data if the disk is full, or who have less space compared to the size of the file you are trying to copy.

  You need to remove the order data to make the space more. Deleted data from the device USB will be permanently deleted and will not be stored in your Inbox, so take care while eliminating unnecessary data.

  I hope this helps.

• Plant system Windows Explorer when copying or moving files: error explore 0xc000012d

  Windows Explorer crashes XP Home (laptop) system when copying or moving files that gives the error message: explore 0xc000012d.  Text and images suddenly begins to disappear from the screen (go faster if you move the mouse on the screen!), system crashes, gives the blue screen and stops. No time to save data, which is happening so fast.  I lose all data in open programs.  RAM is tested without error, ATI Mobility Radeon X 1300 driver has been updated, system fully updated, but nothing is. Could not find any information on the MS Support or on the web that would help.  Please help - tired system crash all the time!

  Pippuri,

  Try to disable the fast user switching and see if that helps.

  Go to control panel, double-click user accounts, and then change the way users log on and outside. Should be a checkbox to turn on fast user switching.

  Let us know if it works. Thank you.

• Error code 0 x 8007052 when copying files from your computer to a memory stick

  Original title: error code 0 x 8007052

  Hi, I'm copying pictures on a memory stick.  About half were copied everywhere but now I get the above error code and the remaining will not pass.  Any ideas, thanks

  Hi Mary,

  If I understand correctly you get an error code when you try to copy files to a memory stick. I'll certainly try and help you get the problem solved. However, until we start could you give us some more information?

  1. when the last time you were able to copy files to the memory stick without any problem?

  2. you have any security program installed on the computer?

  3. are you aware of any recent software or hardware on the computer changes?

  You can download and install the package of the article and check if it helps. If the problem persists, you can start the computer in a clean boot State, and then try to copy the files. Clean boot helps eliminate any conflict of third party software.

  Note: Once the diagnosis is made, follow step 3 of section to configure the computer to start the Normal start.

  Hope this information was helpful and let us know if you need help in the future about Windows. We will be happy to help you.

• Try to Thinapping MS Office 2007, but failed when an error «could not copy ##attributes...» "is thrown.

  Hi all...

  Try to Thinapping MS Office 2007, but failed when an error «could not copy ##attributes...» "is thrown. I'm trying to save the project to a folder under vista (called "shared folder") to a virtual machine by using windows XP SP2. I made a mistake? Your help is really appreciated for the entire community, thank you.

  Hi MrBean344,

  If I was wrong, you will get the error for GetAttributes... while building the project. Am I wrong?

  If so, then I think it was due to the long way to have more than 256 characters. Can you please try to save your project in the short path such as C:\ and rebuild the package?

  I think that after doing this, error is not displayed and application is virtualized.

  Thank you best regards &,.

  Margaux Khopkar

• Error when copying R3D footage in Premiere Pro, After Effects, CC 2015?

  Get the following error during the copy of R3D images above first in After Effects composition timeline:

  

  Never had this problem before, as long as the body and AE were both the same version of CC, copy and paste has worked.  After that error, copy the R3D images on offline.  Any ideas?

  What number of exact version of AE are you using? If you use a Mac and your AE version is 13.7.1, you need to update to 13.7.2.

• backup error "attempt to copy to disk"C:\" "failed. An unknown error occurred (-54). »

  When syncing iPhone 6 running iOS 9.3.1 I get the following error message: "attempt to copy to disk"C:\" "failed. An unknown error occurred (-54). »

  I am running iTunes 12.3.3.17 on a 64-bit Windows 7 Pro computer. I am logged in as administrator. The laptop has 8 GB of RAM and 700 + GB of available disk space.

  It seems to be synchronization of contacts and the calendar correctly, but the local backup fails.

  Does anyone have a solution for this?

  Thanks for your help.

  Help with error 54 here > If you see the error-54 when you synchronize with iTunes

• Satellite M100 gives me error TFncKy when I turn it on

  I have problem with my laptop M100 with shortcut keys.
  It gives me error TFncKy when I turn it on. I did a restore point before I install internet explorer 7 and the problem wasn't there after I installed it, it appeared, it must relate I narrowed down it that much.

  I've got RegCure which is recommended for this kind of problem and it does not work once I've done so many scan. I will not buy another Remover spyware, unless I'm absolutely sure, he will do the job that they want us to pay each one individually.

  If I need to uninstall and reinstall the program, I need to be guided through it, because I did a search in the recovery cd and I can't find the exe program to reinstall

  Sincerely,
  Linda B

  Hello

  I know which is really annoying to you, but I recommend you do the following:

  Back up all your data and recover your computer because you will spend just a few unnecessary time and nerves to find out what the real problem is.
  After retrieving your machine, you should do your updates as usual and set whenever you install new software, a new restore point (as you already :)), then it would be easier for you to find the malicious software that causes this error.

  Maybe you shouldn´t install the IE7, better grab a copy of Mozilla Firefox because they don t cause so many problems with the operating system and other software on your hard drive. (I read today on "plugged in" firefox has been download 400,000 times and I think that 400,000 downloads won´t lie..)  ;))

  Would appreciate comments on your part.

  See you soon

• Error 1097 when calling DLLS in LabView

  I get an error 1097 when calling the LabVIEW provider library. Curiously, the error, the DLL routines still seem to do what is asked of them.  This is the test code.  It opens an Ethernet connection to a controller of axes Galil, he asks (possibly) the value of its internal clock, and then closes the connection.  Each call library function returns error 1097 but "valve function" I32 error number is always zero. Open function causes the connection to be opened, the command function causes the send command and receives a reasonable answer, narrow funtion seems to cause the connection to be closed.

  

  Here is what I see when I run the test:

  

  Also directly configure call-library functions, as I did in this VI, I also tried using the import-shared-library Wizard to create a vilib of functions of the DLL and I get the same behavior and errors when I use these functions.  I tried to tweak some of the data types in my configured manually call library functions to see if I could find a combination that worked better with the library, but had no luck there.

  I use the x 86 version of the DLL with v2014 LabVIEW 32-bit on a 64 bit windows system 7.  I see that the error on the two computer systems of different work configured in this way. I see a similar error on a home computer with just the RTE of 2014 installed. The manufacturer says they can not reproduce the error. I always saw the error over multiple versions of their library DLL.

  In the attachment ZIP it has a link to the DLL library on the manufacturer's website. There is also a copy of the VI, the DLL and a large part of how-to-use documentation that accompanies the DLL.

  I was hoping that someone who was familiar with the use of the call-library function might take a peek at what I do and see if an error could be spotted.

  Unable to find an error, I did, I would be happy to suggestions on how I could solve this. Little seems to me like there may be a problem with the library. The manufacturer, Galil, said that they have opened a log with OR to see if NEITHER could help but since Galil said they can not reproduce the problem and provide an example of the NC, it really went anywhere.

  Given the decoration of symbol names as exported by the DLL I "m convinced that you must change the stdcall calling convention.

• Win2k3 Server IIS SChannel event 36871 "a fatal error occurred when creating the SSL server credential information."

  To make a long story short, I went to use client software that I use a few times a week and it would not connect to the server, complaining not found or number of SSL.  When research various dcom, schannel errors errors in the event logs and a few others, I systematically over the last 24 hours cleared up the boot is so now clean (no time starting network on startup and no message on the service could not start).  It seems that something has happened a month ago after that the server crashed where at least the first DCOM messaged presented themselves, but everything has been working well until it didn't.  The dcom patches end up having to do with the ...\rsa\machinekeys (and the way that it) had a few "account unknown" in it, I cleaned everything that (at a time since I removed all items in this folder, but then put their subsequent return (by crushing all except 2 after creating a new certificate), had to reinstall virtual server and iis 6) , at some point as well.  In any case, I'm at the point where everything works (no event log errors/etc) from startup until you try to connect to the IIS 6 Server using https:... at this point, you get the event SChannel 36871 "a fatal error occurred when creating the SSL server credential information." (no additional information) is connected and the client browser cannot access the site (you can keep trying and it does not work but no event log entry more).  So that's where I'm sitting, http: works fine, https: No.  Certificate appears in the default Web site correct, said valid and possesses the private key, port 443 is there, all addresses by default, netstat shows port 443 same process id as the port 80.  I can't find a copy of SSLDiag do test to see if that prove something?

  So I need help what is not going to get this new job of fixing.  What should I do?

  Thank you!

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. Appropriate in the TechNet forums. Please post your question in the TechNet forums.

  You can follow the link below to ask your question:

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

  I hope that helps!