error-10401 with pcie-6321

Similar Questions

• Error - 10401 with the SCXI-1600

  Hi all

  I have a system of aquistion of data based on the SCXI-1600 and already work with LV6.1 software and I want it to be used with LV12 improve.

  When I tried to record data using MAX I have, it works very well. but trying to save data in labVIEW with function "I acquire waveforms", it gives me error attached 10401.

  can someone help me solve this problem?

  Thanks in advance,

  Ahmed Elsayed

  This function is part of the outdated traditional DAQ driver and your image shows DAQmx is active for the device. You should carry all your code to use DAQmx. DAQmx was introduced with LabVIEW 7. If you choose to stay with the outdated driver, you will need to do a reset and switch drivers, but assistance will be limited.

• Error-200279 with PCIe-6363

  I currently have a simple vi used to acquire data of tension through the DAQ assistant permanently.

  Currently I'm collecting 2 channels sampled at 200 k continuous (due to random events).

  No matter where I put the samples to read, I have several times: error-200279.

  Some other posts, I assume it's because the DAQmx read function and the function "write on a file" are producing at different speeds, causing a shift of data may be.

  To resolve this problem, should I apply the design of producer/consumer model? And if so, I may receive advice on how to actually that implement with my current vi?

  -Matt

  Hi davd24,

  We always recommend to file i/o functions in a separate loop of read/write functions DAQmx. It resembles what is past in your case, is that the time it takes to write to a file is longer that it takes to fill the device aboard the buffer that throws the error you see. Therefore, I suggest the architecture of the producer consumer. Here is a link to a tutorial:

  http://www.NI.com/white-paper/3023/en/

  Also, here is a link to an example of Community produce consumer with DAQmx features:

  https://decibel.NI.com/content/docs/doc-2431

  If you have any specific followed after looking through these questions let me know.

• Retrigger AO finished on PCIe-6321?

  Hello!

  As indicated in the subject, I would like to generate an output on the card PCIe-6321 analog redeclenchables finished-samples (X series).

  I wired faithful to start: redeclenchables enter the node property trigger, but the AO task runs that once after it is started (with trigger arriving constantly pulses).

  Is there anything else I need to implement?

  Assistance, the Commission should support trigger, and I don't get any errors on the execution of the VI.

  Or have I misunderstood the concept, and it is only the counters that can be retriggered?

  Kind regards

  SEB

  Hi Sebastian,.

  the link above was a pretty old one. It should be more suitable:

  Community: Generate several updates of tension with redeclenchables Trigger - National Instruments
  https://decibel.NI.com/content/docs/doc-11304

  To answer your question the X-series (like your PCIe-6321) supports a redeclenchables analog output. Maybe you had a little hiccup with your code, I can't really say the distance.

  Best regards

  Christoph

• Windows 7 - Pci to Pci bridge (error: Code 10)-PCI video card

  Before that I declare my problems I will list what I'm running and I am trying to accomplish.

  I'm under edition 64-bit of Windows 7 Enterprise, not the Beta or RC. I have 3 video cards in my possession (listed below).
  -(PCIe) Evga GTX260
  -(PCI) Evga 9400GT
  -Evga (PCI) Fx5500
  Out of these 3 cards I only use the GTX260 and the 9400GT. I had to "retire" the Fx5500 because drivers latest WHQL (certified) only provided support as far down as the cards of Nvidia "6 series". Unfortunately the Fx5500 is a 'series 5' and falls below this line. I already tried to use the GTX260 and Fx5500 in earlier versions of Windows (XP and Vista), but there is no way to download and install two separate drivers for two of the same video card do - you will have nothing else to errors. There is the option to go to a place like guru3d.com and download a supported driver custom which covers both the GTX260 Fx5500, but drivers are not certified and lack support. Therefore, I bought and now use the 9400GT is covered by pilots for the GTX260, which eliminates the need for messing around with custom drivers. Also, the 9400GT has a better graphics processor and more memory than the Fx5500, so it was time to upgrade anyway.

  Now that you have some info here is my problem, whenever I have install the 9400GT as I get a second entry "pci to pci bridge" (the other entrance has no errors) that appears under "System devices" in Device Manager. The entrance of bridge pci to pci second has a yellow triangle with an exclamation point, which refers to a problem. When you check the properties of this unit it is more or less said that Windows has detected a problem (error Code 10). The GTX260 is still working and still comes in "graphics cards" as a GTX260, but there is no entry for the 9400GT. I tried the 9400GT in two PCI ports and each time it does the same thing. If I get out the GTX260 and ONLY operate the 9400GT, I always get the question of the pci to pci bridge, BUT I get a picture and can boot into Windows 7 without a hitch. When I do that it is still nothing listed under "graphics cards" as a 9400GT or even a VGA compatible device.

  After messing around with this for 10 hours (Yes, I said 10 hours) I decided to dig my retirement (the Fx5500) PCI video card. When I installed this card I had no entry bridge PCI to pci 2nd appear under "System Devices", and one that appeared had no yellow triangle or error codes. I then checked under "Graphics cards" and Windows 7 it was recognized as a VGA-compatible device and asked for drivers.

  Now, I have concluded that there is absolutely no problem with the motherboard or my material (including video cards). In a first time EVGA support and I had suspected that the motherboard may be bad because of all the pre-diagnostic steps I had taken during my test of 10 hours. I won't enumerate what I did because it would literally take 3 hours to type everything in it. Just believe me when I say I've tried many things including but not limited to the latest bios updates (flashed 4 times and reset to ensure accuracy), IRQ customized management, all OS X 2, multiple/latest chipset drivers installed, reinstalling video multiple/last drivers installed, memtest test, complete equipment disassembly and re - build (adding a device at a time) and MUCH more. The only thing I have not tried installing another OS other than Windows 7 64 - bit to see if I could reproduce the problem. It's a waste of time, but because that let's say I install Windows XP Pro and the 9400GT doesn't have this problem... Well, that's fine, but who cares on XP Pro when I used it for the last 9 years and when I have a version full of Windows 7 I want to use? I'm certainly not running XP Pro on Windows 7 just to use the PCI video card. Second, if I install XP Pro and it always gives me the same error of bridge pci to pci and then, I only lost more time than because if it s not to go to work or the other OS, then I m sure that hell will not leave XP Pro installed when I use Windows 7.

  Thank you
  Piyush

  Maybe a stupid question now but has your post anything to do with Toshiba and Toshiba computers laptops?

• constant output voltage DAQ NI PCIe-6321

  Good evening

  I am trying to output a constant tension there 10V DAQassist.
  However, as far as I know, when I want it to generate signals, it will only display waves.

  I'm relatively new to labview and can not fully use the modules of the individual drivers for DAQmx.
  Currently I use an external voltage source to power a set of scales that I'm trying out signals in LabVIEW.
  I've been somewhat successful, but a cleaner set would be to get an output of data acquisition to fully integrate the system
  I know that traditionally deplete you a game recommended by, OR like this:
  http://www.NI.com/white-paper/7138/en/

  However, I work with hardward existing on a limited budget.
  I have an acquisition of data NI PCIe-6321, with a block of connection BNC 20990.
  So, I work with BNC connectors.

  Change the AO writing single-channel > sample > DBL. That should give you a single value whenever you call the VI of Scripture. Also change the entry of data in a single digital control. Maybe call it voltage or something like that? You can probably remove the synchronisation screw DAQmx and the node property Regen as those who will be most relevant.

  A cell of 700 ohm load will draw 10 ohms = 14.3 V/700 mA, which is still well above the 5 limit my AO lines.

  A load cell is wired as a bridge. It is the equivalent of two voltage dividers. Without load on the output of the cell the two lines have equal tension: 5.00 V. When you have a 20 mV out of load cell tension on the two output lines will be 4,990 V 5,010 V (or 5,000 V and 5,020 V, according to the internal configuration). So your 6321 must be configured to accept 5,020 V (plus a bit of noise, mistakes and overload conditions). So, you will need to set it to 10 V range. On the 6341 (I happen to have the factsheet - the 6321 is probably very similar) which means a +/-10 V rank. Which translates a theoretical resolution of 0.3 mV. The output 20 mV full scale of the load cell, it comes down to resolution of 6 bits (6: 16).

  Two possible ways to improve: 1. use a preamplifier or a signal conditioner to amplify the 20 mV at a few volts. These usually have the differential amplifiers to reject common-mode 5 V. voltage They can also have hardware filters.

  2. use a power supply excitement split so that the load cell is excited by the + 5V and - 5V. This puts the common mode voltage to ~ 0 V and you can use the +/-0.2 V rank on the lines of HAVE it.  The resolution is then about 6 uV and the effective resolution on your signal is approximately 11 bits.

  Lynn

• OR PCIe-6321 custom PCB connection

  Hi you all,.

  I design a PCB custom at the interface between our sensors and our NI PCIe-6321.

  1 - can use a non shielded cable to make the connection? We work with low frequency shielded cable (less than 100 kHz) signal will cause trouble, because everything will be locked in a small space.

  2 should. what kind of receiver I use on the printed circuit to interface with cable (RC68-68)

  Thank you!

  Fabrice

  Hi Fabrice,.

  This document contains the set of our connection connectors Multifunction DAQ card.  You'll want to check out the section of connectors up 0.050 map 68 pins under the connectors and basket funds for SCSI connectors.  You can get either the right angle or vertical mounting of our website or a 3rd option part of the seller.  (We provide the part in this document number, if you want to buy it elsewhere).

  Kind regards

• IMAQ extracted buffer is suspended in an ongoing acquisition with PCIe-1429

  I acquire images of 500 x 500 pixels at 1000 FPS from a camera of the Basler A504k using a PCIe-1429 (LabView 8.6, x 64 Vista). The images are processed online, and all works - some time. From time to time the program and out of just to extract vi buffer never gets. No error is produced. I need to kill Labview and restart it to leave. I read http://forums.ni.com/t5/Machine-Vision/BUG-with-PCIe-1429-Cameralink-full-config-Basler-sprint-lines... and implementation of the proposed solution, but no luck. I followed the lost images and buffer number called and can't find any problems. My VI is attached. The images, go to a queue and treatment by another part of the program. Any help will be much appreciated.

  Thanks Vinod,

  Another thing is that the structure of your program looks a little broken. You are extracting tampons from the ring, put a reference to the image in your queue, and then going back and extract a different buffer. This means that your previous buffer is no longer checked and could be replaced, but your loop else may not have finished processing this image yet.

  While this should be causing your current problem, but I thought it is interesting to point out. I think I have two queues of the source images. One that contains free images and one that contains the populated images. You producer loop of who you've given here would consume the free queue, take in one of these images, and then place it in the populated queue. Your consumer loop would be remove from the populated queue, process the image, and then put the image in the free queue.

  Eric

• X 230 error 1802 with the Correct WLAN card

  Recently, I ordered my brand new x 230 for the start of the University and selected the thought of WLAN card default option which would be sufficient for my needs. After the hand signal and dropouts, problems I decided to upgrade the WLAN card that would improve the signal strength.

  I know the existence of the 'white list' frustrating that means that some cards are allowed to use. So, I went in the store of Lenovo and looked for what was the best WLAN card that might come with a new order of a 230-System x, as surely they are on the whitelist.

  Later, I bought an Intel Centrino Ultimate - N 6300 card and installed correctly in my x 230. However, from the start I saw to my despair that the 1802 error was there, tells me my card has not been approved. Could someone explain how hell a card that can come already installed in x 230 is not did not whitelist checking?

  Needless to say I am not very satisfied with Lenovo, because I can't even find a list of what cards are accepted. What is the point in a white list anyway? I am a student trying to patch BIOS to remove it, but no one has yet done a patch.

  Why do I get an error 1802 with this card?
  Thank you.

  Hello and welcome,

  Doesn't have that 6300 come from the store of Lenovo, or from a vendor who said it was for a Lenovo laptop?

  The card type is not the whole story when comes to the white list.  In addition to the correct (6300) type by its PCI vendor and device ID, it must have an ID of subsystem of Lenovo.  (IIRC, it can be more precisely not the subsystem ID, but the effect is the same).  A generic 6300 will not work.

  A card must be sold by Lenovo or pass the white list.  Reputable suppliers will provide a number of Lenovo FRU (CRU) to check the FRU list for the machine.

  For example. Since the research database of Lenovo parts -> ThinkPad X 230page, the RUF for that 6300 is 60Y3233.  It was not easy to find.  The RUF are not in the hardware maintenance manual any more

  If your card has a number of Lenovo FRU, something else is in place.

  [edit] types andyP faster as I do...

  Z.

• Help! Export error 27 with only a few videos

  I exported Final Cut Pro X projects directly on my external hard drive. I got an error 27 with one of them, and given that it is exported well I don't think it's a problem with my external hard drive formatting. All the videos have been imported in the same way and the same camera. Any ideas about why this is happening? Thank you!

  Most likely, you export a FAT32 / 'Windows' formatted the disk, right?

  error27 occurs when you attempt to save a file > 4 GB - that is not supported by fat32 (very old format..)

  So, small export projects, larger not. -.

  reformat the drive (erases all content!) to exFat or hfs + / "Mac"...

• receive the error message with every new open tab

  Whenever I open a new tab, I get a popup error message. I have screen shots that can be granted.

  At first, I thought it was a mistake to Java, but I've uninstalled and reinstalled Java.

  There are two error messages which read:

  [JavaScript application]
  evalInSandbox:Error: Permission denied for <https://facebook.com> create a wrapper for the object of class UnnamedClass.

  [JavaScript application]
  Error: Permission denied for <https://facebook.com> create a wrapper for the object of class UnnamedClass

  So I clicked on help > troubleshooting information and choose Reset Firefox.
  Now I get a new error message with every new tab open.

  [JavaScript application]
  Error: syntax error

  Please tell us how to do this.
  Thank you
  JudyLeeThurber

  1. In the address bar, type Subject: config and press enter. The subject: config "this might void your warranty!" warning page may appear.
  2. Click on I'll be careful, I promise!, to continue on the subject: config page.
  3. Type browser.newtab.url
  4. Double click on the first result, a new window should now display.
  5. Type of topic: newtab in the area.
  6. Click ok and load a new tab. It now works of mireille?

• DI/O cards such as the 651 x are compatible with PCIe 1 x?

  Hello

  This can be a bit of a stupid question, but it's my first outing with NEITHER and yet I somehow received some amount of responsibility for a very strange procurement process.  I hope the question is easy to answer and that will mitigate its possible idiocy.

  Are maps such as the NI 651 x (http://www.ni.com/datasheet/pdf/en/ds-105) compatible with PCIe 1 x?  Of the image, it looks like they are designed to run on PCIe 16 x, but since the speed is not a major concern, that I wondered if she settle and operate normally on PCIe 1 x.

  I am limited in contracts with a default value, extensive construction of tower PC organization, whose mother has two PCIe 16 x and two PCIe 1 x.  Since I will probably need three cards, I was hoping that it would be compatible with the PCIe 1 x slot and we would save the hassle of special purchase order form.

  Thanks for any help!

  N ° it is even not a PCIe connection.  It's PCI.  I recommend that you call your local representative of OR discuss your needs and they can help steer you in the right direction.

• docking w520 with pci-e slot, but few likely?

  Hi, is there such a thing? I have a w520 I want to put a raid or hba cards. My t61 had a dock with pci-e slot and I'm looking for something similar.

  no such thing with the ThinkPad W510, W520 W530, new.

• CAN I USE PXI-8330 WITH PCI-8331

  CAN I USE PXI-8330 (CHASSIS) WITH PCI-8331 (PC)?

  CAN I USE PXI-8331 (CHASSIS) WITH PCI-8330 (PC)?

  CAN I USE OR PXI-8110 (CHASSIS) WITH PCI-8330 (PC)?

  IS CONTROLLER MUST BE THE SAME MODEL?

  Hello

  MXI controllers have a pair use, as you can see the manual on page 1-4.

  http://www.NI.com/PDF/manuals/370840b.PDF

  OR PXI-8110 is a PXI controller, so it's a computer doesn´t need to be connected to a PC using a card-MXI.

  Kind regards

  Abel

  OR Brazil

• I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe.

  original title: error with ehshell.exe

  I have Windows XP Media Center Edition Version 2002 with Service Pack 3 and I tried to run Media Center but I get an error message with ehshell.exe. Could you help me?

  This problem exists since the 1st Media Center. SP2 and SP3 had a difficulty, but it is obvious that it doesn't always. The same problem still exists in Vista today with a lot of other carried over from XP. System restore would work, but you do not have any good restore points so reinstall an operating system seems to be your only option.

  You probably don't want to do an OS reinstall you need for Media Center, but since it does not at all, you might want to play then remove the Media Center updates and or SP3 and reinstall them.