Error in Recon - 11 GR 2 ad group

Similar Questions

• Error when adding new subnet for CSM group

  Hello

  I'm trying to add a new subnet to an existing group in the CSM v4.0.1 b7823 company.  When you add a new subnet to the Group (the other elements of the group is a different subnet), CSM emits several errors for each SAA touched:

  Description:

  BB (GROUPNAME), referenced by the 'Http network' on maps (DEVICENAME) device to multiple network IP addresses!

  Cause:

  Made http refers to a network object that corresponds to more than one IP address on the device

  Action:

  Please config the policy with the network object that resolves to a single IP address.

  There is an error for ICMP as well.  The group is already a /24subnet content, I don't think it's a clear mistake.  Has anyone encounter this?

  Thank you very much.

  Justin

  Hi Justin,

  what you observe is normal given the way in which we have set up the remote access policy. As you probably know, in cli, you can specify only one rule of access by line for ssh, http, telnet etc...

  For example, if you want to allow ssh access to ASA lines host 1.1.1.1 and 2.2.2.2 you put two

  SSH 2.2.2.2 255.255.255.255 outside

  SSH 1.1.1.1 255.255.255.255 outside

  The CSM, we model this two lines as two different object, so the building of network type block object that refers to the object of type ssh access can have only one entry. This behavior is the same for ICMP as well.

  Access list is different because we model to the CSM in a different way, plus you can use the object-group put on different networks. It is not possible to access to the device.

  I hope that gave you an overview a little more on the reason

  Also it would be nice to score this answer if this is the case

  Stefano

• ERROR - 1051414 - cannot set the role of group with shared services [30:1101:JNDI error] error.

  Hi all

  I tried provide access to filter the group in both SSP and thru Maxl command but still get the error below. Any experience of this problem? If Yes, please let me know how you solved this problem.

  
  

  ERROR - 1051414 - cannot set the role of group with shared services [30:1101:JNDI error] error.

  
  

  Thanks in advance!

  Krishna

  Read the support document that I posted the link, prior to changes for openldap ensure you that it is saved.

• No Internet access. error 1747. and the dependency service or group could not start

  Have a laptop dell inspiron 1545 with vista (build 6002: service pack 2).  Have a wireless network at home.  laptop stopped connecting to the network 2 weeks ago.  When I try, I get a message "dependency service or group was able to start.  When I go to manage networks, there is no detected networks.  Cable internet access also does not work with this laptop. cards (minimap dell 1397 Wireless) wireless and ethernet say thet controller work correctly.  2 other laptops in the House are normally working on the network.  Reviewing service autoconfiguration WLAN and Wired AutoConfig and when I try to start the two ths get message... "Error 1747 the Authentication Service is unknown".  Another little thing, I noted... isatap.home don't works do not-message says to download the drivers- but not on net so cant)... don't know if this is related.

  can you help me?  Thank you, Aodhanm.

  I just wanted to post that I used the

  netsh winsock reset

  command to fix this same error 1747 known when you try to manually start the WLAN
  on a Windows 7 Pro computer.

  After a restart it worked fine.

  Chuck
  NerdForce.com tech

• Error in moving VMS to the resource group

  Hello

  I'm trying to rebuild some ESXi hosts due to a hardware refresh. New ESXi hosts are in a cluster and eventually the old cluster will disappear because the virtual machines are migrated. I've implemented the script that works fine except for 1 error below. It seems that since we have groups of resources with the same names in all are clusters, it cannot determine where to place the virtual computer. Is there a way to specify the ID of the resource pool with the Move-VM command or another command? Or maybe a way to point to the list of resources in a cluster through a sort of way? I can easily rename Resource temporarily pools, but I want to continue to use the part of the script later to other familiar things.

  The exact error is that the specified parameter 'destination' expects only one value but your 'Low priority' name criteria corresponds to multiple values.

  Thanks in advance for any help!

  

  Hello

  Try something like this,

  $RP = get-ResourcePool | Where {$_.} {ID-like "* 27663"}

  Move-VM - VM VMName - Destination the $RP

  Kind regards

  Julien.

• Error in PipelineManager while creating the new group payment

  Hello world

  I am trying to create a new group of payment for the purchase of an item with reward points.  I'm trying to change the flow of the pipeline by substituting commercePipeline.xml.  I added the following lines of code in this XML.

  CommercePipeline. XML

  < pipelinemanager >

  < pipelinechain name = "validatePaymentGroup" >

  < pipelinelink name = "dispatchOnPGType" >

  < transition returnvalue = "5000".

  Link = "validatePointsPG" / >

  < / pipelinelink >

  < name pipelinelink = "validatePointsPG".

  transaction = "TX_MANDATORY" >

  < processor = jndi

  "/ com/mystore/order/processor/ValidatePointsPaymentGroup" / >

  < / pipelinelink >

  < / pipelinechain >

  < pipelinechain

  name = "validatePaymentGroupPreConfirmation" >

  < pipelinelink name = "dispatchOnPGTypePreConfirmation" >

  < transition returnvalue = "5000".

  Link = "validatePointsPGPreConfirmation" / >

  < / pipelinelink >

  < name pipelinelink = "validatePointsPGPreConfirmation".

  transaction = "TX_MANDATORY" >

  < processor = jndi

  "/ com/mystore/order/processor/ValidatePointsPaymentGroup" / >

  < / pipelinelink >

  < / pipelinechain >

  < / pipelinemanager >

  When I start booting the server error below:

  ERROR [nucleusNamespace.] Could not start the service "/ atg/commerce/PipelineManager ': atg.nucleus.ServiceException: CONTAINER: atg.service.pipeline.PipelineInitializationException; Source: ATG.service.Pipeline.TransitionException: A PipelineLink is already mapped to return code [5000] in the pipelink named [dispatchOnPGType].

  When I tried to check the commercepipeline in the Administration of the Dynamo , is to show that the pipelinechain is locked

  CommercePipelineManager

  Pipeline channels

  String ID	Riders of num	Activated	Locked	LockAcquiredTime	LockReleasedTime	LockingThread
  validatePaymentGroup	0	fake	true	Fri Jan 24 10:55:46 IST 2014	N/A	main
  loadOrder	0	true	fake	N/A	Fri Jan 24 10:55:44 IST 2014	N/A
  updateOrder	0	true	fake	N/A	Fri Jan 24 10:55:44 IST 2014	N/A
  processOrder	0	true	fake	N/A	Fri Jan 24 10:55:45 IST 2014	N/A
  validateShippingGroup	0	true	fake	N/A	Fri Jan 24 10:55:46 IST 2014	N/A
  refreshOrder	0	true	fake	N/A	Fri Jan 24 10:55:44 IST 2014	N/A
  processOrderWithReprice	0	true	fake	N/A	Fri Jan 24 10:55:44 IST 2014	N/A
  repriceOrderForInvalidation	0	true	fake	N/A	Fri Jan 24 10:55:44 IST 2014	N/A
  validateForCheckout	0	true	fake	N/A	Fri Jan 24 10:55:45 IST 2014	N/A

  Thank you and best regards,

  RKishore

  you have assigned the return code 5000 in the two strings to your new pipeline link.

  OOTB 5000 is already assigned to charge the chain.

  You must change the return code new value unassigned. Also the return code should be added in return codes provided by dialing ValidatePaymentGroupByType.

  Refer to this: Oracle ATG Web trade - confirmation of order extending to new methods of payment of support

  Thank you

  Nitin.

• Error in recon OIM 11g

  Hi all
  I have a recon job target custom. When the job is run for the first time, the recon events are created and processed, but when I run the following query, I don't see the events are completed:
  
  Select rb_key, rb_batch_status, rb_profile_name from recon_batches where rb_batch_status = 'initiated ';
  All events of my stay in State initiated.
  
  If I run the job again for the same users, I get the following error:
  
  oracle.iam.reconciliation.exception.ReconciliationException: Exception occurred when inserting data into the table RA_APP_NAME145 reason of
  Inner exception: java.sql.SQLException: ORA-01422: exact fetch returns more than number of lines
  ORA-06512: at "OIM_OIM. RECON_CREATE_EVENTS', line 69
  ORA-06512: at "OIM_OIM. RECON_CREATE_EVENTS', line 122
  ORA-06512: at line 1
  
  No matter who faced this problem before and what is the resolution to this?

  To resolve this problem, refer to Metalink doc: ORA-01422: while to run Recon Job in OIM 11 g [1384816.1 ID]

• RPT to Oracle 10g - REP 300 error: table or view does not exist GROUP BY...

  Hello - I have a request to the Interior of my data model that works very well when I launches the report inside reports developer & works well in TOAD. But when I try to run from our forms 10 g GUI report fails with a REP 300 error: table or view does not GROUP OF S.SOURCE_NAME
  
  Source_name is my group of field & as mentioned, it works very well to the developer reports & TOAD, so I can't understand why the GUI is having a problem. The GUI uses some features to export the data to Excel. I have no more info on how the GUI do that then maybe no one will be able to help, but if you run into this situation before, any input you have would be greatly appreciated. Thank you!

  Hello

  connect you as a user even in the forms and the TOAD?

• FRM - 40212 / FRM - 40222 error on a radio during the query group

  Hi all
  
  This is my first post, so please bear with me if I did not provide enough information or am not clear at all.
  
  I use Forms Builder (Web) on a 10g database. I have a number of databases and elements non-base of data as part of a block of data.
  My problem is that when I enter a value in a field and click the query button, I have an invalid value FRM-40212 for error field on my radio group (section disabled, non-base of data, which is populated by programming in the triggers of post requests and amended list only). When I click ok, I get an error of FRM-40222 disabled point Validation failure on the same radio group.
  
  This does not happen if I click on the button "Enter the query" before you enter values in the fields, but I don't want my users to encounter this error if they try to interrogate without clicking "Enter the query" first.
  
  I would like to know why exactly this error happens - what it means?
  I read in other forums that setting the required article property to false solves this problem. But how can I do this with a group of radio buttons? And if it is not possible, anyone have any suggestions for other workaround solutions?
  
  Thanks in advance,
  
  Abigail

  Hello

  You can avoid this by defining "Mapping of other values" to a fo value of radio buttons. As if you need to radio radio1 and radio2 associated group R1 radio button, then set the option buttons the initial value of this property to 'Mapping of other values' radio button R1. You will not see this error.

  This error occurs because as your loading a screen without assigning a value to the option button.

  If this helps brand question as answer or useful.

  Thank you
  Pavan.

• Impossible to access the system restore, getting the error "system restore has been disabled by group policy.

  Recently, I was hit by a virus that, among other problems, he blocked my access to the system restore to clear it. After having had my pc repaired I can not even access the system restore or my registry. I get a message from that system restore has been disabled by group policy. It's my own pc and I am the administrator. I've tried a few things without success. I hope someone can help me with this. I have the vista operating system.

  1. click on start, run and type regedit.exe , and then press enter

  2. navigate to the following key:

  HKEY_LOCAL_MACHINE-Software-policies-Microsoft-Windows NT------SystemRestore

  In the right pane:

  • Delete the value DisableConfig
  • Delete the value DisableSR

  3. exit the registry editor.

  Other tips, tricks and support are available at: www.waltwachon.weebly.com

• Error: "the system restore is disabled by group policy" when he tried to use the system restore

  Original title: group policy

  When I try to use the system restore, I get "system restore is disabled by group policy. How can I fix this problem?

  Hi bluelilly,

  1. is your computer connected to a domain?
  2. don't you make changes before the show?

  This occurs if the Configuration policy to disable is enabled on your system, either by using Group Policy or through the registry editor. For stand-alone systems Windows Vista, follow these steps:
  Step 1: Using the Group Policy Editor. If your edition of Windows Vista includes the Group Policy Editor (gpedit.msc) snap-in, follow these steps:
  a. Click Start, type gpedit.msc and press ENTER.
  b. go to the following branch: Computer Configuration | Administrative templates | System | System restore
  c. double click on disable the Configuration and set it to not configured.
  Note: If the above setting is already set to not configured, set it to "Enabled" and click on apply. Return back the setting to not configured, then click on apply, OK.
  d. Quit Group Policy Editor.
  e. restart the computer and check the difference.

  Step 2: Using the registry editor
  a. Click Start, type regedit.exe and press ENTER
  b. navigate to the following key: HKEY_LOCAL_MACHINE-Software-policies-Microsoft-Windows NT------SystemRestore
  (c) in the right pane, delete the value named DisableConfig.
  d. Quit Registry Editor.
  e. restart the computer and check the difference.

  Very important: Modifying the registry incorrectly will cause serious damage to the computer. Back up the registry until you make changes.
  See Registry backup

  If your computer is connected to a domain, then we recommend that you post your query toTechnet Forums Windows Vista to improve the assistance.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error in Recon target

  Hello
  
  Our IOM has configured Target_RO used for the reconciliation of the target. We have a strategy of access through which each user created the IOM will be placed in service in this ROLE.
  
  When a user is created in the IOM, it gets placed in service at Target_RO with success (via the access policy).
  
  If there is an update the profile of the user in this resource, that is, update from the resource (Target_RO) a new instance of the BR target is added to the user for the first time. If there are no more updates, this instance is updated accordingly.
  
  Thus, overall user has two instances of the same Number, i.e.
  (1) when a user is created in the IOM by trusted source (different source of recon tåget)
  2.) whenever an update through Target_RO.
  
  How to prevent two instances? We only want one instance to be given to the user at any time. Pls suggest.
  
  Thanks in advance.

  This isn't the cause of the problems and the way of..,.

  Your store proc adapter must collect the values of the process shape and process form must be completed via pre pop adapter that will copy the data of
  the user form and push them to process the form.

  So do your key as mandatory field.

  Thank you
  Suren

• What is the code for error "the dependency service or group could not start": 1068

  What is "the dependency service or group could start"?

  This seems to be a HUGE problem for PC users so much; It gives rise to the error 1068 code and effects so many aspects of our machines...

  What is this area of computing? What it means? If we understood this, solutions might be easier to find?
  From what I can deduce (I could be wrong) there seems to be a communication error; But why did affect many different areas of the machine?
  I recently corrected an error 1068 on an internet connection and then again on spooler print issue; Now, I'm trying to solve the error even on a sound broadcast. Frustrated? Isn't the half of it! WHAT IS THIS ERROR?

  the dependency service or group could not start
  http://social.technet.Microsoft.com/forums/en/itprovistanetworking/thread/563b908c-AA24-4000-9b2d-b6ff02f10c56

  No sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Tips for solving common audio problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

• Windows 7 Edition home premium error "Windows cannot connect to the Group Policy client service."

  Original title: guest for Windows 7 Home Premium account

  Hi all

  I would like to aid which has had to face the problem below and how it was fixed.

  I have Window 7 Edition home premium and created a guest account with normal privileges that is turned on but cannot access with the error "Windows could not connect to the Group Policy client service" I think that the main problem is related to a policy because when put on the account to administer it in pop, error message says 'Cannot connect to a windows service' Please check group policy log.

  Thank you very much in advance

  Hello

  Thank you for your time and effort to get back to us, and I apologize for the delay in responding.

  Method 1 step number d makes reference to the present Details tab on the event viewer, where you can get the details of the error. First, search for the error which will be something like Windows cannot process extension Client Strategy Group-side and click on the error and then click the Details tab and make a note of the GUID (Globally Unique Identifier) for the extension defective client-side. For reference, see the screenshot:

  

  Now come to step f number , it indicates the location of the Group Policy Extensions so that you can check if the extensions shown in the case log and the Registry Editor extension have a difference. The path of the GPExtension is HKEY_LOCAL_MACHINE\Software\Microsoft\Windows NT\CurrentVersion\Winlogon\GPExtensions. For reference, see the screenshot:

  

  Let us know if the steps are clear to understand now. If this isn't the case, we will be happy to help you further.

  Thank you.

• Windows 7 print spooler does not start: System error 1068 occurred. The dependency service or group could not start

  Hello

  I still have the "system error 1068. The dependency service or group was able to start.

  "I use Windows 7 Home premium 64-bit and my printer is HP PSC 1310 series.

  I downloaded the latest driver in the HP website, but it will not continue installation that the print spooler is not started.

  I tried "restart the spooler to print the title of the services, it does not, with the error message above.

  I have check the dependencies and it say HTTP and RPC

  I check on RPC and DCOM Server process Launcher two dependencies and the RPC end point Mapper is started

  I went to regedit and found the keys as follows I don't know if its correct:

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Spooler]

  'DisplayName"="@%systemroot%\\system32\\spoolsv.exe,-1 '.

  "Group"="SpoolerGroup."

  "ImagePath" = hex (2): 25, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 d, 00, 52, 00, 6f, 00, 6f, 00,------.

  74,00,25,00, 5 C, 00, 53, 00, 79, 00, 73, 00, 74, 00, 65, 00, 6 D, 00, 33, 00, 32, 00, 5 C, 00, 73,------.

  00,70,00, 6f 00 6f, 6 c, 73, 00, 00, 00, 76, 00, 2nd, 00, 65, 00, 78, 00, 65, 00, 00, 00

  'Description"="@%systemroot%\\system32\\spoolsv.exe,-2 '.

  "LocalSystem ObjectName"=""

  "ErrorControl" = DWORD: 00000001

  "Start" =: 00000002

  'Type' = dword:00000110

  "DependOnService" is hex (7): 52, 00, 50, 00, 43, 00, 53, 00, 53, 00, 00, 00, 68, 00, 74, 00, 74, 00,------.

  70,00,00,00,00,00

  "ServiceSidType" = DWORD: 00000001

  "RequiredPrivileges" is hex (7): 53, 00, 65, 00, 54, 00, 63, 00 62 00, 50, 00, 72, 00, 69, 00, 76,------.

  00,69,00, 6 C, 00, 65, 00, 67, 00, 65, 00, 00, 00, 53, 00, 65, 00, 49, 00, 6 D, 00, 00, 65, 70, 00,------.

  72,00,73,00, 6f, 00, 6F, 00, 61, 00, 74, 00, 65, 00, 50, 00, 72, 00, 69, 00, 76, 00, 69, 00, 6 c,

  00,65,00,67,00,65,00,00,00,53,00,65,00,41,00,75,00,64,00,69,00,74,00,50,00,------.

  72,00,69,00,76,00,69,00, 6 C, 00, 65, 00, 67, 00, 65, 00, 00, 00, 53, 00, 65, 00, 43, 00, 68,.

  00,61,00, 6F, 00, 00, 65, 67, 00, 4F, 00, 6f, 00, 74, 00, 69, 00, 66, 00, 79, 00, 50, 00, 72, 00,------.

  69,00,76,00,69,00 6 C 00, 65, 00, 67, 00, 65, 00, 00, 00, 53, 00, 65, 00, 41, 00, 73, 00, 73,------.

  00,69,00,67,00, 6F, 00, 50, 00, 72, 00, 69, 00, 6 d, 00, 61, 00, 72, 00, 79, 00, 54, 00, 6f, 00,------.

  6 b, 65, 00, 00, 6F, 00, 50, 00, 72, 00, 69, 00, 76, 00, 69, 00, 6 c, 00, 65, 00, 67, 00, 65, 00, 00,------.

  00,53,00,65,00, 4 c, 00, 6f, 00, 61, 00, 64, 00, 44, 00, 72, 00, 69, 00, 76, 00, 65, 00, 72, 00,------.

  50,00,72,00,69,00,76,00,69,00 6 C 00, 65, 00, 67, 00, 65, 00, 00, 00, 00, 00

  "FailureActions" = hex: 80, 51, 01, 00, 00, 00, 00, 00, 00, 00, 00, 00, 03, 00, 00, 00, 14, 00, 00,------.

  00,01,00,00,00,60, EE, 00, 00, 01, 00, 00, 00, 60, ea, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00

  
  

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Spooler\Performance]

  "Close" ="PerfClose."

  "Collect"="PerfCollect."

  "Collect Timeout" = dword:000007 d 0

  "Library"="winspool.drv".

  "Object list"="1450".

  "Open" = "PerfOpen."

  "Open Timeout" = dword:00000fa0

  
  

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\Spooler\Security]

  "Security" = hex: 01, 00, 14, 80, 78, 00, 00, 00, 84, 00, 00, 00, 14, 00, 00, 00, 30, 00, 00, 00, 02,------.

  00, 1 c, 00, 01, 00, 00, 00, 02, 80, 14, 00, ff, 01, 0f, 00, 01, 01, 00, 00, 00, 00, 00, 01, 00, 00,------.

  00,00,02,00,48,00,03,00,00,00,00,00,14,00, 8 d, 01, 02, 00, 01, 01, 00, 00, 00, 00, 00,------.

  05, 0, 00, 00, 00, 00, 00, 18, 00, ff, 01, 0f, 00, 01, 02, 00, 00, 00, 00, 00, 05, 20, 00, 00, 00,------.

  20,02,00,00,00,00,14,00, fd, 01, 02, 00, 01, 01, 00, 00, 00, 00, 00, 05, 12, 00, 00, 00, 01,

  01,00,00,00,00,00,05,12,00,00,00,01,01,00,00,00,00,00,05,12,00,00,00

  I go to C:\Windows\System32\spool\PRINTERS, there is nothing for me to remove it.

  Any other advice would be greatly appreciated...

  Hello yan_dao69,

  I suggest that you try the methods below to solve the problem.

  Method 1:

  I suggest that you run the printer troubleshooter. This will automatically diagnose and fix printing problems:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Ideally, this would set the print spooler service issues.

  Method 2:

  I suggest that you disable the Antivirus software temporarily and verify if you are able to start the print spooler service. You can check the link that will give you information disable antivirus below:

  http://Windows.Microsoft.com/en-in/Windows7/disable-antivirus-software

  Note: Please make sure that you enable the antivirus software after the test to keep your computer protected.

  Method 3:

  Check the dependency of the spooler services in the registry.

  a. Click Start, type regedit in the search box and press ENTER.

  b. look for, and then click the following registry key:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Spooler

  c. right-click on spooler, click Export, save a backup file on your desktop.

  NOTE: If an unforeseen problem be encountered after changing the registry, please double-click on the file to restore the backup.

  d. in the details pane, if the DependOnService value shows values of RPCSS and other key, right-click DependOnService and then click on edit.

  e. in the value data box, delete the other keys and then click OK.

  f. exit the registry editor.

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756 ) how to back up and restore the registry in Windows.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.