Error Stop: 0x0000001A Memory_Management

Similar Questions

• STOP: 0X0000001A (0XC0402000, 0X00000B12, 0 X 00005003, 0X00B146FF)

  Hi, on my old computer Windows Vista, I got up the Blue Screen of Death at startup, and it gives me the error code "* STOP: 0x0000001A (0xC0402000, 0x00000B12, 0 x 00005003, 0x00B146FF) 'I can't go in any of the safe Modes (Safe Mode, Mode safe mode with networking, safe mode with command prompt Mode)." I tried to re-seating memory which did nothing. I couldn't find any solutions online, I hope someone here can help me. It is a 32-bit system with 2 GB of memory with an Intel Pentium processor.

  A value of 0x0000001A MEMORY_MANAGEMENT bug control a. This indicates that an error occurred serious memory management.

  .  Run these two tests to check your memory and find which driver is causing the problem.

  If you are overclocking reset all default before running these tests.
  In other words STOP!

  1 - Memtest.

  * Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. "http://www.memtest.org/#downiso"] Memtest86 + - Advanced Memory Diagnostic tool

  * Boot from the CD and let it run at least 5 or 6 passes.

  Remember, anytime Memtest reports errors, it can be bad RAM or a bad motherboard slot.

  Test the sticks individually and if you find a good, test it in all slots.

  Any error is indicative of a memory problem.

  If a well-known stick fails in a slot of motherboard, it's probably the slot.

  http://www.SevenForums.com/tutorials/105647-RAM-test-Memtest86.html

  2. Driver Verifier

  Using Driver Verifier is a dubious proposition. Most of the time it will crash and it will tell you what is the driver. But sometimes it will crash and will not tell you the driver. Sometimes it will crash until you can connect to Windows. If you can't mode without failure, then you will have to resort to editing the registry offline to disable driver verifier.

  I suggest that you first back up your data and make sure you have access to another computer so you can contact us in case of problems. Then do a system restore point (so you can restore the system using the functionality of Vista/Win7 Startup Repair).

  In Windows 7, you can do a startup repair disk by clicking Start... All programs... Maintenance... Create a system - with Windows Vista repair disc, you need to use your drive installation or from the "Repair your computer" option at the top of the Safe Mode menu.

  So, here is the procedure:
  -Go to start and type "auditor" (without the quotes) and press enter
  -Select 'Create a custom settings (for code developers)' and click 'Next '.
  -Select "Select individual settings from the list complete" and click "Next".
  -Select the entire document except for "Low resource Simulation" and click "next".
  -Select "Select driver names from a list", then click "next".
  Select all drivers that are NOT provided by Microsoft, and then click "Next".
  -On the next page, select "Finish".

  Restart the system and wait as he crashed to blue screen. Continue to use your system normally and if you know what are the causes of the crash, do it several times. The objective here is to get the system crash because Driver Verifier is stressing out the drivers. If it is not planted for you, then let it run for at least 36 hours of continuous operation (an estimate on my part).

  If you are unable to Windows because it crashes too early, try safe mode.
  If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.
  http://www.SevenForums.com/tutorials/101379-Driver-Verifier-enable-disable.html

  Further reading
  "http://support.microsoft.com/kb/244617"] using Driver Verifier to identify issues with Windows drivers for users advanced

• hanging of windows 7 blue screen STOP: 0x0000001A (0 x 00041287, 0x0080D366, 0 x 0, 0000000 0000000

  Hello

  My PC works very well but a bit slower than before. but as soon as I want to analyze the computer or to change my security settings the computer hang or sometimes shows a blue screen with this error:

  STOP: 0x0000001A (0 x 00041287, 0x0080D366, 0 x 0, 0000000 0000000)

  It was then that that I am facing this problem and shortly, I write what I did:

  1.i made a backup and format the computer and reinstall windows 7, but the problem was still there.

  2 change the RAM and HARD drive, but the problem was there even if the problem wasn't their share.

  3. I asked some experts they said maybe you should change the motherboard, but that's the last thing I want to do because it's almost cost me new computer and I think the problem is something else.

  4. After all this, I decided to work with the computer anyway because I had so much unfinished business, then I realized my keyboard does not work. I bought a new keyboard and it worked.

  now my problem is up to this:

  I could work with my computer totally fine but it isn't as fast as ever, but that's fine. as soon as I scan the computer or change some settings the computer hangs or sometimes shows error blue screen!

  What should I do?

  Please help me

  y at - it a hope that I could fix it this computer.

  Hello

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  According to the description, I understand that you have a problem with slow performance, or sometimes the system hangs while parsing.

  Certainly, I understand your concern and will try my best to help you.

  I appreciate all your efforts really to try to solve this problem.

  I would suggest trying the following methods and check if that helps.

  Method 1:

  Try to run the troubleshooter of performance and check if it helps. Please follow the steps outlined in the article below.

  Note: The resolution of performance problems check issues that could slow down the performance of your computer, such as how many users is currently connected to the computer and if multiple programs are running at the same time.

  Open the troubleshooter of Performance

  http://Windows.Microsoft.com/en-us/Windows7/open-the-performance-Troubleshooter

  If the problem persists, follow method 2

  Method 2:

  I suggest you try to follow the steps in the link given below and check if it helps.

  How to use the tool File Checker system to fix missing or damaged system files, please follow the steps in the link provided below.

  https://support.Microsoft.com/kb/929833?WA=wsignin1.0

  Note: System File Checker is a Windows utility that allows users to find corruptions in Windows system files and restore the damaged files. This article describes how run the tool (SFC.exe) System File Checkerto scan your system for files and to repair the system missing or corrupt files in Windows. If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected.

  If the problem persists, follow method 3

  Method 3:

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft, security scanner please follow the steps in the link provided below.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

  For reference:

  We may also refer to the article below and check if that helps.

  8.1 Windows, Windows 8 or Windows 7 hangs or freezes

  https://support.Microsoft.com/en-us/KB/2681286

  Note:  When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  Important: While running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area so all available data on this risk to be lost.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

• Error: STOP 0x0000007B while installing XP

  Hello.

  When I tryied to get xp installed on my laptop toshiba, I got this error: STOP 0x0000007B
  I have a hard drive with this nummer serieal S/N 18LQT85GT
  I heard that I needed a software to get this right.

  Can you help me for xp back?

  Greetings

  Boyfriend sorry but how to help if you didn t offers useful info?
  What model of laptop do you have?
  What Windows XP Home edition, you are trying to install? SP1 or SP2?

• HP MINI 110 FATAL SYSTEM ERROR STOPPED. [redacted]. !!!

  HP MINI 110 LAPTOP FATAL SYSTEM ERROR STOPPED.

  [number of Series edited by Moderator]

  Please someone SOLVE THIS PROBLEM. I HAV NOT OPEN MY LAP FOR 3 months...

  Hello

  Try to enter: e9loq3f5ne (3rd character is a lowercase L)

  Kind regards

  DP - K

• HP mini 110 computer: password check failure fatal system error stopped CNU9384ZG7

  Can someone please help. I've not turned my HP Mini computer in a few months and when I did I got this error. Password check failure fatal system error stopped CNU9384ZG7.

  Please enter = e9lofuv0hx

  Kind regards

  K N R K

  I work for HP

• password check failure fatal system error stopped CNU902254V its a hp mini 1035nr

  password check failure fatal system error stopped CNU902254V its a hp mini 1035nr. I forgot the password. can anyone help?

  Try the jam.

  e9lo177qv6

  3rd letter tiny L.

  4th letter lowercase O.

  8th letter lowercase Q.

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  IF demand for CURRENT password using this code.

  REQUEST NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

  I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

• Compaq Mini CQ10 CNU00872CY: password check failure fatal system error stopped CNU00872CY

  have the same problem on my hp mini.
  password check failure fatal system error stopped CNU00872CY
  Please helpme to slove this problem

  Please enter = e9l11ux7ei

  Kind regards

  KNRK

  I work for HP

• Error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000).

  I have error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000). I did the F9 Diagnostics and no error found. Also, I tried to remove the DVD and replace the video card, but no improvement. However, Windows starts normally in SafeMode only. Thanks for supporting.

  Product ID: 89578-OEM-7332157-00061

  Hello

  Specifying your version of Windows and other information would help help us to you.

  How to ask a question
  http://support.Microsoft.com/kb/555375

  -----------------------------------------------------------------------------------------------------------------

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  ===============================================================
  
  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Two main causes of these blue screen video drivers and BIOS - check with the system manufacturer
  Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
  other pilots to check there. Disable the installation of self as those who are older and if
  Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

  See the methods of update driver generic and verify the implementation of driver verifier in the next
  Message.

  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Cause

  Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.

  • 0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

  Make sure you have enough disk space.

  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If you do not know the specific cause of the exception, consider the following:

  • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

  You can solve the problems of BIOS by upgrading the version of the system BIOS

  BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
  * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

  =============================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Mini Compac: password check failure fatal system error stopped its a computer hp mini CQ10 CNU0133TLF

  password check failure fatal system error stopped CNU0133TLF its a computer hp mini CQ10. I forgot the password. can anyone help?

  Hello

  Come in:

  e9l13ffak8

• Error: STOP 0X0000000A (0XOOOOOOE8, 0 x 0, 00000002 00000001, 0X806E4A16.)

  Original title: no update

  For a month, I'm having a lot of problems

  I have this computer for 8 years and so far, works very well, but after a month he gave me a lot of problems.

  I have also formatted and receive sevral error messages

  delay in writing, no disc, STOP 0X0000000A (0XOOOOOOE8, 0 x 0, 00000002 00000001, 0X806E4A16)

  Help, please

  Hi Kam.rani,

  Thanks for the question.

  It would be useful that you could answer this question to help you further.

  1. you remember to make changes before the hardware or software issue?

  2. you try to perform windows updates?

  Here is a link that gives you steps to solve this problem.

  You get a message error "Stop 0x0000000A (IRQL_NOT_LESS_OR_EQUAL) error code" in Windows XP

  Note: The above article contains steps to disable the third-party antivirus software. Be sure to enable the security software on the computer after checking the issue.

  If you need further assistance, please answer and we will be happy to help you.

• I get the blue screen error - error - Stop 0X0000008E

  -Stop error 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000)

  Hi I get the blue screen error - error - Stop 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000) and cannot use the pc in safe mode. I have XP - OS. I really don't want to reformat the HARD drive and you want to avoid reinstalling as much as possible

  Hi aromaveda,

  ·         Have you made changes on the computer?

  Follow these methods.

  Method 1: Follow the steps in the article.

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Follow the steps in the article to check the drive for errors.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

• Blue screen error: STOP: 0X0000007B (0XF78D2, 524, 0XC0000034, 0 x 00000000, 0 x 00000000) while trying to install windows XP

  Original title: Windows has shut down to not to damage the computer

  When I go to install windows, it gets a blue screen with this error:

  STOP: 0X0000007B (0XF78D2, 524, 0XC0000034, 0X00000000, 0X00000000)

  Hello

  See the article below that could be useful.

  Advanced troubleshooting of errors "Stop 0x0000007B" in Windows XP
  http://support.Microsoft.com/kb/324103

• ERROR STOP 0X0000007B I can't CROSS the BLUE SCREEN

  AS YOU CAN SEE FROM THE ABOVE TITLE, I CAN'T GO PAST THE SCREEN BLUE WITH THIS MESSAGE.  sAFE MODE WILL NOT WORK.  What DO I NEED to TRY NOW?  THANKS FOR THE HELP.

  1. http://support.microsoft.com/kb/316401 
  Error message "STOP 0x0000007B" when you restart your Windows XP-based computer

  2. http://support.microsoft.com/kb/324103 
  Advanced troubleshooting of errors "Stop 0x0000007B" in Windows XP

  Possibility: You may receive an error message "Stop 0x0000007B" If your computer is infected with a boot sector virus.

• Windows does not start, an error "STOP 0xC000021A", with status0x00000000 (0 xC0000001 0x0010034C)

  Computer was working fine.  All of a sudden I get this error, an error "STOP 0xC000021A" r, with status0x00000000 (0 xC0000001 0x0010034C) when you try to start.  It goes to the blue screen and says could be due to material change or missing files windows.  Troubleshooting still try to repair windows startup goes to blue screen and shows an error \windows\system32\winload.exe status 0 x 0000001, missing or damaged. I had all the hardward checked and from what I've read, somehow this file has disappeared and now my computer will not boot. Tried all I can think about. Any ideas?

  Hi novstarzz,

  There seems to be a hardware problem, I suggest you to the manufacturer of the computer to contact for assistance on this issue.