Error with duplicate DTD SYSTEM integration

Similar Questions

• Qosmio G20 error message: problem with the cooling system has been detected

  I'm trying to fix a Qosmio G20 (which is about 3 years old, it is no longer in warranty).

  Error message: Warning: a problem with the cooling system has been detected.

  I managed to remove the outer case and observe the operation of the machine, and basically one of the fans does not at all. The fan which is closest to the power connector seems to work very well (he seems to be turning a lot, do not know if this is normal), but the other fan who does not seem to move at all.

  When I put in place the case and on the machine, I noticed after a few minutes the vent of the fan working heat sink had warm enough, while led the non-working fan remained cool.

  I cleaned the fan from dust and have also changed the BIOS battery mode mode high performance, but the problem still exists.

  I would be grateful if someone could give advice if the problem is the fan or something else.

  If the fan is the problem, where I can buy a: i live in the United Kingdom?

  Hello

  I think there might be something wrong with the cooling module and the replacement would be necessary.
  Usually, this should be done by an authorized provider (ASP) in your country.

  Technicians could replace it with a new part and also could renew the thermal grease which is placed between the module and the CPU cooling.

  So contact the ASP in your country and ask for later handling.

  By the way; also, you can buy the cooling of the ASP module!

  Good luck

• Error message "A problem with the cooling system" on Satellite A660

  Hi all

  Hope I can get help here. I got about 5 laptop computers HP after each of them had problems and errors. I got sick of them and so got a refund and bought a high spec A660-1FH.

  The A660 is a great laptop for two days until yesterday when I started having a saying of warning message "a problem with the cooling system has been detected. Please turn off the power immediately and return it for service "."

  The cpu fan works fine you can here it turns and the temperature of the processor i5 - 460 m is around 40 degrees for two hearts - that seems normal to me. I noticed that this happens only when running on battery, and if you switch from eco utility to the power saving mode. Its fine when running on the "balanced" power setting The fan is louder before when this message appears.

  Like its less than 28 days my retailer swapped it for a brand new immediately. Got a new home page, and the same message reappears. Everyone knows this. Like two laptops had this, I was wondering if it is normal that the laptop A660 series or if it was really a hardware problem?

  I tried to update the eco utility and the bios of the laptop, but the two are the latest versions. Can someone help or share if they have a similar problem with their laptop?

  Thank you

  In front of me, I have Satellite A660-13 q (PSAW3E) and I have about 6 weeks now. It works almost 10 hours a day and so far I didn't notice this message or anything that may be suspect for the operation of the equipment.

  I put really know why this happen on your laptop and don t think that there is nothing you can do about it.
  I would trade it again. What you can also try is to contact the closest service Toshiba. Make a call, explain the situation and ask if they can help you with this.

• When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.

  original title: log question.

  When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.  How can I fix?

  Hi KERRYYX,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?
  4. What is the full error message that you receive?
  5. Are you able to restart and shut down the computer?

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  You cannot log off, restart or shut down your Windows XP-based computer

  http://support.Microsoft.com/kb/831431

• 'ink system failure' error with code oxc19e0023 on a HP Photosmart Premium all-in-One Printer - C309

  'ink system failure' error with code oxc19e0023 on have a HP Photosmart Premium all-in - One Printer - C309g - did all resets and reinstall the ink also tried to replace ink with new carts HP... frustrated please help

  Have you tried the steps outlined in this article:
  http://support.HP.com/us-en/document/c03081973

  If not try the steps and tell us if it helps.

  Good luck!

• Error while trying to run a visual Basic (.vbp) project in Visual Basic 6.0 with Windows 7 (64-bit) Enterprise saying "error access to registry system.

  Hi guys,.

  In my last computer the VB6 project worked with Windows XP but now I changed to Windows 7 and I can't run some application in visual Basic 6.0 that I still...    (I'm meaning to open the .vbp file to run in the environment of VB6 and not talking is not running the .exe).

  When I open the .vbp (from Visual Studio Enterprise 6.0), then comes an error saying "The system registry access error" only on this Windows 7 (64 bit)...

  I can not changes made in VB6 or compile programs is it my Windows 7?   There must be a solution that I think... something to execute or modify.

  By the Way this is my first post on Microsoft Answers and hope to get lucky on that first and solve my problem; (O)

  Thanks for any information

  M.

  Hello

  1 are logged as administrator?

  2. is it works much earlier?

  Method 1: Try to "Run as Administrator". VB6 needs to access the registry, and user account control sometimes gets in the way.

  Method 2:

  You can check the following link and check if it solves the problem:

  PRB: Error access to the system registry ' Message When displaying VB/VBA references.

  http://support.Microsoft.com/kb/269383

  Method 3:

  As you may have run the program under Windows XP, you can try to run it in compatibility mode and check if this solves the problem. See the following link for more information.

  Make older programs in this version of Windows

  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows.

  For additional help with this specific technology, please ask your question to the MSDN Visual Basic Forums.

  http://social.msdn.Microsoft.com/forums/en-us/vbgeneral/threads

  I hope this helps.

• Satellite C660-21Z - System Message about the error with cooling system

  I've had my laptop for 11 months now, and in the last days a system message was appearing on my screen saying there is a problem with the cooling system and that I should turn off the laptop and return it for service. I'm not sure if it a message genuine system or if it is in fact spam.

  The answers would be grateful to you

  Hello

  I have read on this message and looks like it s a software bug
  Have you noticed any problems with the cooling system? I mean something like a higher temperature or unexpected shutdown from the bottom?
  If not then it's a bad alarm
  You can ignore this message and I read that after new system recovery the message did not appear again.

• Processing error of the driver at the start of the system: «there seems to be an error with your instalation.» Please reinstall your application'

  Original title: driver cure

  After installation of IE 8, I get a message with start up

  Driver cure

  "There seems to be an error with your instalation. Please re install your app '

  IE8 is the last that I instaled.

  Under Win XP home dell Pent 413400 Mhz; 1.28 GHz, 256 MB of RAM. Thank you, jaro

  Hi Mooneymaniac,

  You can start your computer in a clean boot to find the program that is causing the problem. To do this, try the following steps:
  a. open the article: http://support.microsoft.com/kb/310353
  b. method 2, follow steps 1 and 2, and then restart the computer to see if the problem persists.
  c. If the problem does not persist in the boot, then follow step 3 and step 4 to find out which is the origin of the problem, and once you have found the culprit, uninstall the program and check the result.

  Note: Don't forget to follow the steps in the steps to configure Windows to use a Normal startup state"" section.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Strengthening of the error with Eclipse project

  I'm running into a strange error build a project with Eclipse.

  I have Eclipse version 3.6.2 with BlackBerry Java plug-in 1.3.0.201102031007 - 19 and two SDKs (6.0.0 and 5.0.0.36).

  I am trying to build a library of references this project application project.  Here's the error I'm getting to the stage of packaging:

  Packaging project myApplication_BB
  C:\Apps\Eclipse\plugins\net.rim.ejde.componentpack6.0.0_6.0.0.30\components\bin\rapc.exe -convertpng -quiet codename=deliverables\Standard\6.0.0\myApplication_BB deliverables\Standard\6.0.0\myApplication_BB.rapc -sourceroot=C:\Users\GA\workspace\myApplication_BB\src;C:\Users\GA\workspace\pointTrace\src;C:\Users\GA\workspace\myApplication_BB\res -import=C:\Apps\Eclipse\plugins\net.rim.ejde.componentpack6.0.0_6.0.0.30\components\lib\net_rim_api.jar;C:\Users\GA\workspace\Codename1_BB\deliverables\Standard\5.0.0\Codename1_BB.jar;C:\Apps\Eclipse\plugins\net.rim.ejde.componentpack5.0.0_5.0.0.36\components\lib\net_rim_api.jar C:\Users\GA\workspace\myApplication_BB\bin
  C:\Apps\Eclipse\plugins\net.rim.ejde.componentpack5.0.0_5.0.0.36\components\lib\net_rim_api.jar(net_rim_amms.cod): Error!: Duplicate definition for 'net.rim.device.internal.amms.AMMSMain' found in: C:\Apps\Eclipse\plugins\net.rim.ejde.componentpack6.0.0_6.0.0.30\components\lib\net_rim_api.jar(net_rim_amms.cod)
  Packaging project myApplication_BB failed (took 7.369 seconds)
  

  When I searched the Web for this error I found this link: http://docs.blackberry.com/en/developers/deliverables/23650/eJDE_1.3_SDK_7.0_Known_Issues_1526151_11...

  However, he talks about debugging, and I get not even package the project.

  It seems that he tries to import into a Pack 6.0 and 5.0.  I specified my TERM as 5.0 when creating projects.  Is there a way to force it to use only 5.0?  I could not find anywhere in the project properties.

  Thank you for any information.

  Hello

  check if only they designate same JRE, if the library project and the client of the project when they use different library, you are bound to this kind of questions, change them to the same operating system and check

  Concerning

  Rakesh Shankar.P

• Satellite C660-223 - system caution: "" problem with cooling detected system "".

  When I carry my Satellite C660-223 somewhere for example wear at home to College in a protective case in my backpack, I sometimes get a window warning flashing upward every 20 seconds or so said system + "warning: a problem with the cooling system has been detected." Please turn the computer off immediately and return it for service. +

  This only happens when I transported somewhere and as a first step, that these warnings system flashed only sometimes upwards after I hauled somewhere, but in the last two years, he started to get pretty much whenever I took the laptop somehwere. When the system warnings blink until the computer doesn't feel a little warmer than normal. no danger of overheating, immediately.

  I didn't fix it because the problem seems to resolve itself the next time that I carried the computer somewhere. It's a very strange problem where the short-term solution was the same as the cause: as in I would take the laptop somewhere, the warning system flash upwards and I learned that take "for a walk" would fix somehow everything which was the 'problem '. I solved the problem in this way too often so he could be a coincidence.

  So for a while it wasn't really a problem because I just didn't take the laptop anywhere. But the warning system has recently start flashing to the top if I wear just the laptop on the floor, and the warning system does not disappear with my method incredibly non-tech-savvy to "go for a walk", which I am sure many here would give something to laugh :).

  The obvious answer is that I need to get the service pronto thing, but I'm in the middle of final exams and the situation of tech in my house means I can't leave the laptop away for service for who knows how long when I really need to study.

  Responses, I'm hoping to get are ideas as to what actually caused this problem and short-term solutions that are a little better informed that my approach "going for a walk".

  I think THAT what is, is that the movement to carry your laptop around in a backpack something within the done cooling system moving out of place causing the evil TI work. I say this because, while writing this thread I was turn the laptop over and over again to get a look at the stickers on the back and the practice that seems to have "solved" the problem of warning system because this window flashes up while he was only a few minutes ago.

  It seems so that all component moved his place before been moved back again by the movement to turn the laptop over and over. And I was not even take him for a walk!

  Any help? Thanks in advance.

  Hello

  This notification may appear for different reasons.
  The alert might appear due to
  (1) cooling system malfunction
  (2) blocked cooling vents or fans
  (3) software question (VAP - added value package or BIOS)

  Malfunction of the cooling system, you should contact the service agents at the difficulty.

  In case of a blocked vent and fans it s enough to clean the parts using a jet of compressed air.
  This allows to get rid of dust inside the cooling module.

  If the vents are not blocked and you still see this message, check the application of the service station for updates on your computer. If any are found, download and install.
  You can try to uninstall or update the Toshiba value added Package. This package contains a few essential tools and utilities that control the cooling system too.
  Also check BIOS update.

  But if you continue to receive this error, your laptop may require repair

• Satellite A660 - message: WARNING: a problem with the cooling system

  My laptop recenly started giving the error "Warning: a problem with the cooling system has been detected." Please turn off computer immediately and return it for service"- Yes the fan had stopped working and touchpad area was hot.

  So I take it on the type of service (toshiba) and must answer for fan, Mo, HARD drive, he said. Is this possible? -J' I have extended warranty, but is ' t it much? not to mention that it takes a month to get things down.

  He also mentioned that I could use the machine with a cooling pad until then if I wish.

  Any feed back?

  > Yes the fan had stopped working and touchpad area was hot.

  In this case, there is really a hardware problem.
  But I m wondering why he should replace the HARD drive and the motherboard
  Perhaps only the cooling module began at malfunction of course this is just a speculation
  If the technician has checked the material, then they need to know what parts are not OK.
  So don t think you have no choice.

  But the guarantee is valid for all is free

• Satellite P500-12D - a problem with the cooling system has been detected.

  Hi there everyone,

  I bought a Satellite P500-12D, which was a return of retail. When I start it up it runs a few minutes and then it appears on the screen:
  WARNING: A problem with the cooling system has been detected. Please, turn off computer immediately and return it for service.

  Follow the health of toshiba CPU is less than 50% temp and if it goes much higher that the cooling fan turns on and it lowers down and the fan stops again, I noticed that only the fan works r/h to cool the cpu, both should come together? What is a software problem?

  TThe unit is new without even the plastic off the surround screen or webcam. Any help or even point me in the right direction would be much appreciated, gary

  Hello

  Which program gives you this error message about the cooling system?

  Before contacting a service partner, as you can read in the error message, you must clean the cooling system using a jet of compressed air. Maybe dust blocking the fan or something else. Of more to clean up it of not necessary to disassemble.
  Here is an article on this topic: [how to clean a Toshiba laptop cooling system? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=40]

  If it doesn't help, contact the nearest service partner.

• Satellite L350-214 - error with the software Reeltime

  Hello

  I have a Satellite L350-214 with Windows 7 Pro and have encountered an error with the software Reeltime, I uninstalled and reinstalled and still get the error below. Any help or assistance would be great

  Tony Miller

  Log name: Application
  Source: Windows Error Reporting
  Date: 2010-11-30 12:27:58
  Event ID: 1001
  Task category: no
  Level: Information
  Keywords: Classic
  User: n/a
  Computer: Tony-TOSH
  Description:
  Fault bucket 1223018385, type 5
  Event name: CLR20r3
  Answer: No available
  Cabin ID: 0
  Signature of the problem:
  P1: tosreeltime.exe
  P2: 1.0.0.0
  P3: 4a769d0e
  P4: WindowsBase
  P5: 3.0.0.0
  P6: 4b5950b7
  P7: a86
  P8: 18
  P9: System.InvalidOperationException
  P10:
  Attached files:
  C:\Users\Tony\AppData\Local\Temp\WER7C9E.tmp.WERIn ternalMetadata.xml
  These files are available here:
  C:\Users\Tony\AppData\Local\Microsoft\Windows\WER\ ReportArchive\AppCrash_tosreeltime.exe_25c5a6496c7 ad44943ce88637e3389e8a80bd45_07f0c745
  Symbol of the analysis:
  Recheck for solution: 0
  Report ID: d5b71327-fc74-11df-a596-00266c333aed
  State: 0
  The event XML:
  
  
  
  1001
  4
  0
  0 x 80000000000000
  
  37886
  Application
  Tony-TOSH
  
  
  
  1223018385
  5
  CLR20r3
  Not available
  0
  tosreeltime.exe
  1.0.0.0
  4a769d0e
  WindowsBase
  3.0.0.0
  4b5950b7
  A86
  18
  System.InvalidOperationException
  
  
  
  C:\Users\Tony\AppData\Local\Temp\WER7C9E.tmp.WERIn ternalMetadata.xml
  C:\Users\Tony\AppData\Local\Microsoft\Window s\WER\ReportArchive\AppCrash_tosreeltime.exe_25c5a 6496c7ad44943ce88637e3389e8a80bd45_07f0c745
  
  
  0
  d5b71327-fc74-11df-A596-00266c333aed
  0
  
  
  My system specs

  Hey,.

  If you get this error Reeltime, you should try Ccleaner. There may be a registry problem and CCleaner might solve this problem. This great freeware and easy tool which you can download here:
  http://www.Piriform.com/

  Check this box!

• Satellite C660D - a problem with the cooling system has been detected

  My laptop is a * Toshiba Satellite C660D-11th * and I have a message that keeps coming up every once in a while 'alert system' head and reads as follows: "WARNING: a problem with the cooling system has been detected." (Next line) Please, turn off computer immediately and return it for service. »

  I had this warning for the coming weeks and it tolerated, but it worsened and annoyed me for the last time. I can hear the fan and the computer is not over heating (the CPUCool freeware tool detects a 51º CPU temprature C). No further questions arise as the computer slows down, it is right in the path of what I do, like typing right now.

  I tried to solve the problem by changing the "Power Options" in the control panel of Windows 7 'High Performance', and then selected under the 'battery' both 'Sector' columns, 'Never' for the parameter "put the computer to sleep. It seems to work, and no error message has occurred since then. However, this is not a solution...

  Please help quickly, this prevents me from working and even other things now.

  Thank you

  Hello

  Usually, this message would appear if something is not wrong with the cooling system. But I read here in the forum that maybe it's a bug of software and after new system recovery this message should no longer appear.

  But if you notice some upper temperature or abnormal noises, then I recommend to check this with a service technician

• HP Mini 110: Help! Password verification failed fatal error... System CNU9359B3P

  Help! My Hp Mini showed that...
  Password check failed
  Fatal error... System stopped
  CNU9359B3P

  Dear customer,

  Welcome and thanks for posting your query on the Forum from the HP Support

  Looks like you are looking for a password here, we will surely help you with this problem

  Please try this password = e9lofqopf2

  Steps to follow:

  1. Use the posted above unlock code to access the BIOS
  2. Disable all passwords that are enabled
  3. If current password request - type the unlock code
  4. New password, simply press the ENTER key
  5. Repeat the same thing to check the password column.
  6. Then exit the BIOS saving & exit option to save the changes.

  Troubleshooting:

  Incase if the password does not work please try a Hard Reset as follows.

  1. Shut down the laptop
  2. Disconnect the power adapter and remove the battery
  3. Hold down the Power button for 30 seconds
  4. Plug the power supply/AC adapter (leave the battery for now) & start Notepad
  5. If now see you a password, please enter the same password I've shared before and press on enter

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the star KUDOS left to say thank you*.

  Make it easier for others to find solutions by checking a response 'accept as Solution' if it solves your problem.

  Thank you

  K N R K

  Although I am an employee of HP, I speak for myself and not for HP