ETH_PORT_ACTIVATION_PKG

I see this under the General management of licenses. and grace timely 120days. What does that mean? Also I see nothing intalled under licenses. Does this mean that I can't use vm or 1000v fex?

Nexus 1000v Essentials is free now. If you need more advanced security features you will need to allow advanced editing. It is authorized by CPU ESXi host. VM - FEX or Nexus 1000v to have the vSphere Enterprise Plus licenses.

VM - FEX has always been free but still requires vSphere Enterprise Plus licenses.

With regard to port licenses;

6120 s come with 8 ports that are allowed out of the box and any plug-in comes with licenses

6140 s come with 16 ports that are allowed out of the box and any plug-in comes with licenses

6248 s come with 12 ports allowed out of the box, if you have the optional 16-port expansion module you get 8 more licenses.

6296 s equipped with 18 ports allowed out of the box, if you have optional 16-port expansion modules you get 8 more licenses for each of them.

http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.1/b_UCSM_GUI_Configuration_Guide_2_1_chapter_01101.html#concept_02B3BE130EA54738A97CB23D97198B78

Tags: Cisco DataCenter

Similar Questions

  • UCS FC have licensing Question

    Hi all

    Could you please let me know if we need licenses on the UCS for CF service system runs.  All I have in the form of license is:

    I have the pair of 6120's

    use to see the UCSM-1A /license #.

    Name default feat Total used as State as scope

    Used peer status thanks

    ------------------------------ ----- ------- ----------- ---------- ------------

    -------- ----------- ----------

    ETH_PORT_ACTIVATION_PKG 8 8 4 license Ok

    Corresponding to 0

    ETH_PORT_ACTIVATION_PKG B 8 8 4 license Ok

    Corresponding to 0

    YEW is the DURATION Mode and is connected to a Nexus 5010 via an uplink port. When I do 'flog dat sho' I don't see not all entries.

    Pointers?

    The UCSM is in Mode 'CF End Host' hope (assuming).

    However the FI will run in mode of VAN.  You have successfully configured the Nexus with NPIV.  The Nexus 5010 interface should operate in mode 'F' (but car should be good too).

    There is not any FLOGI until you have configured a service profile UCS with a vHBA for SAN boot or local boot and the vHBA on the host operating system tries to access the storage.  Have you done this yet?

    A command can be useful to you is from the CLI UCSM (ssh to the virtual IP of the UCS)

    connect NXOS

    Show Van flogi-table

    If you do not see a flogi VAN here entry, you will not see it on the Nexus 5000.

    Robert

  • Use fixed Port 6120 licenses

    I looked in the 6120 via line cmd and noticed that the output of 'show the use of the licenses' indicates that there is a license 8 ports but none are used. If this is the case, what do the 12 remaining ports of license? What happens if you use two of them to the Ethernet uplinks to the North?

    demonstrate the use of licenses
    Feature Ins Lic status Date comments
    County
    --------------------------------------------------------------------------------
    No. FM_SERVER_PKG - unused-
    No. ENTERPRISE_PKG - unused-
    No. FC_FEATURES_PKG - unused-
    ETH_PORT_ACTIVATION_PKG No. 8 never - used
    ETH_MODULE_ACTIVATION_PKG No. 0 unused-
    --------------------------------------------------------------------------------

    Hello..  I have a similar output in my configuration of lab. In my lab setup, I have not purchased a license and I can use port 19 and 20, in fact all ports. It seems that the license is based on trust and not really applied.  Rgds Eng Wee

Maybe you are looking for