FFT to display with newspaper frequency axis

Similar Questions

• DAQmx task Read DAQmx with sampling frequency of 10 Hz produced much too much data

  I have a simple configuration with a strain of channel 4 OR-9237 amp holds a carrier of series C of WLS - 9163 (wired ethernet mode) - Details probably does not matter.

  I used MAX to create a DAQmx task associated with which all four gauges samples.  The calendar setting is "Scan Loads" is continuous sampling, 2 k buffer (read samples) and 10 Hz rate.  I guess that this task would generate 40 data values per second - 10 for each channel.

  I have a simple loop of reading using DAQmx Read.vi that works always (without any stimulation time).  Playback is set to read all available data and then pump it into a table.
  In the attached example, I also added a few words of debugging to stop the loop after N iterations.

  As the loop is programmed with a 0.2 second period, I expect each pass of the loop to read about 8 samples or 2 samples per sensor.  Instead, I get hundreds each passage.  It's like reading has substituted the sampling frequency specified in the task of the unit.  I absolutely need data to be material to the rhythm.

  Where have I lost?

  Thanks Adnan,

  I changed your example I selected 'Strain gage' entry analog and then lowered the minimum and maximum thresholds to +-1-2.  What happens is that each other in the loop, I 2048 samples or zero samples.  The display flashes a whole line and then it clears any other past.

  In response to your second post, I understand that the loop cannot run quite right that I select.  I think that, but at a sampling frequency of 10 Hz, I have to sleep on the software side for nearly a minute before I built 2 K samples.

  I played with the frequency of sampling, assigning to various values from 0.1 to 10000Hz.  The behavior is the same until I approach the high rates where available samples remains to 2048-4096 sometimes, the display becomes continuous.

  Ahhh, Darn.  Yet another search was this link that points to the root of my confusion.  The 9237 can taste arbitrary rates using its internal clock.  Duoh!  I wish that the pilots are smart enough to warn you if there is a discrepancy between the selected sampling rate and capabilities of the device

• Only the Inbox displayed, with no menu for other areas such as "sent".

  Only INBOX menu, displayed with no menu for SENT, DRAFTS etc. on the left flank and with the FILE EDIT etc missing high.

  Hope you can help.

  All the best,

  Stan

  Features universal key to display the hidden menus bars is alt or F10. After that the display of the menu bar select View-Toolbars and rekindle the missing toolbars.

  Then in the menu bar select View-presentation-folder pane to rekindle that.

• rMbp mid-2014, external display with the quality of the retina

  Hello!

  I buy a Dell 24 "external display to connect to my rMBP with QHD (2 560 x 1 440) resolution.

  http://www1.euro.Dell.com/content/products/ProductDetails.aspx/Dell-u2515h-monit or? c = en & l = en & s = dhs & cs = frdhs1

  I have connected the screen to my mbp with the mini display / port cable supplied with the display screen. It works well, but I don't have quality of retina at all (the images seems good but the text is terrible)

  The text have a bad record as a retina screen, and it makes a big difference when I spend my retina display to the external display which is not comfortable at all.

  I though that this kind of screen was OK to view the retina... but I was wrong. I try to connect with minidisplay / display and HDMI! HDMI made was worse than minidisplay. The res in the system report show was good 2 560 x 1 440. I even try the hack to force with the patch, but always bad RGB render text...

  More important, I want to, it's having the same record as retina on the text and images. What external display can be good for this?

  My budget is 450-€500

  Thank you

  The size in pixels of the screen is not mean much: a small display to 2560 x 1440 pixels seems much sharper than a widescreen 2560 x 1440 pixels.

  Your retina Macbook has something like 220 dpi (DPI in English), the Dell screen only 117. If you want the same sharpness, you will need to choose a display with 220 dpi. But then, everything on the screen will look much smaller. Here is a tool that allows you to get the idea: http://dpi.lv/

• Sometimes a web page is displayed with only text and no picures. It is not always the same site and is not always the case. If I'm going to explore for the same website that always works

  Sometimes a web page is displayed with only text and no picures. It is not always the same site and is not always the case. If I'm going to explore for the same website that always works

  Hello

  Also try a Ctrl + F5 refresh. This allows to bring the content of the page again.

• PREMIUM HP: HP PREMIUM: improve 2 VAR APP with interception of axis Y

  Here the desired improvement:

  With MS Excel, in linear regression is chosen, it is possible to define the intercept with the y-axis.

  Its is interesting when you know that the correct answer is y = M * X (for example: d = V * t or A = k * C (beer-Lambert),...)

  So, I suggest to add this new setting with linear, polynomial, and exponential regression.

  Thank you.

  Simpler: F1 (X) = Statistics_2VAR Sigma (XY) / Statistics_2VAR. Sigma(x2)

  Then 'User Defined' and fit: F1 (X)

• 800 Mini G2 EliteDesk: Dual 4K displays with EliteDesk 800 Mini G2?

  I have an EliteDesk 800 Mini G2 with the i5 - 6500T CPU and integrated graphics card Intel 530. There are also two DisplayPort connectors. As the title says, I tried to find out if the device supports two monitors 4K 3840 x 2160 @ 60 MHz. The specs seem to suggest that it would work. I'm confirming without having 2 K 4 monitors on site. Anyone know or have experience with a configuration like that?

  The i5 - 6500t supports up to 3 screens to 4096 x 2304 @60 Hz

  http://Ark.Intel.com/products/88183/Intel-Core-i5-6500T-processor-6M-cache-up-to-3_10-GHz

  Implementation of multiple 4K displays with your EliteDesk 800 Mini G2 will work. Your EliteDesk Mini supports up to three displays to the right of the box. I suggest using the displayport output ports.

  http://www.Intel.com/content/www/us/en/support/graphics-drivers/000005580.html

• Apple Cinema Display with old Mac

  Hello! I was wondering, I have an apple Cinema Display with the famous ADC video plug. I also have a couple of old Mac without a monitor, for example a performa 6360 Powermac 6100 and Macintosh iicx and Iisi. Y at - it a video adapter to use the movie with these old Mac screen? is this possible?

  Thanks in advance!

  The main obstacle is that a screen ADC must get its power through an ADC port on the computer. The old Mac you list can only the power of their old school connectors.

  I remember this adapter:

  http://www.eBay.com/ITM/Apple-Mac-A1006-DVI-to-ADC-adapter-cord-for-cinema-monit 221995991474 or-display-EMC-1918? hash = i...

  be needed to power a monitor ADC to an ADC not Mac, but I would feel much better if another old graybeard archived to check my aging memory. You still need an adapter to convert the DVI on the adapter port 15 pin Apple old Mac. Some 6100 s required a special just HDI15-to-DB15 adapter to use a normal Apple display that would have been contemporary the 6100:

  

• Cannot update the display with v.156.16 on the Satellite A100-599 Vista nVidia Driver

  I have Windows Vista Ultimate Edition in Satellite A 100-599. Update NVidia display with 156.16 version driver is not possible. A fact Vista Ultimate 32

  bit.

  Any solution to this problem?

  Thank you.

  Hello Kerim

  Can you please tell me what happening exactly when you try to install NVIDIA Driver 7.15.11.56.16 version. ?

  Do you have problems with the display only driver?

• How to structure the DMA buffer for SMU 6341 DAQ card for analog output with different frequencies on each channel

  I use the outgoing/incoming analog DDK with the DAQ 6341 SMU map.

  The examples, for example aoex5, show a single timer (method outTimerHelper::loadUI), but the example shows the DMA loaded with same size of vector data.

  There is a comment in the outTimerHelper:call rogramUpdateCount, which implies that memory sizes different pad per channel can be used.

  (the comment is: switching between the sizes of the various buffers is not used)

  Nobody knows what should be the format the DMA buffer for data from multiple channels with different frequencies?

  For example, we want a0 with a sinusoid at 1 kHz and a1 with a sine wave of 1.5 Khz.  What looks like the DMA buffer?

  With the same frequency for each channel, the data are interleaved, for example (ao0 #0, ao1 #0; ao0 ao1 #1, #1,...), but when the frequencies for each channel is different, what the stamp looks like?

  Hello Kenstern,

  Data are always intertwined since each card has only a single timing for each subsystem engine.

  To AO, you must specify the number of samples that will be released to the AO. You also specify the number of channels. Because he didn't is that a single engine timing for AO, each AO will be channel will be updated at the same time to update clock tick. Data will be interlaced exactly as shown in the example because each channel AO needs output at each tick of the clock to update. The data itself can change depending on the frequency you want to copy.

  kenstern wrote:

  For example, we want a0 with a sinusoid at 1 kHz and a1 with a sine wave of 1.5 Khz.  What looks like the DMA buffer?

  With the same frequency for each channel, the data are interleaved, for example (ao0 #0, ao1 #0; ao0 ao1 #1, #1,...), but when the frequencies for each channel is different, what the stamp looks like?

  In your example, you must come with an update rate that works for the two waveforms (sine waves of 1 and 1.5 KHz). To get a good representation of a sine wave, you need to update more than 10 x faster than your fastest frequency... I would recommend x 100 if possible.

  Update frequency: 150 KHz

  Channels: 2

  Then create you stamps that include complete cycles of each wave you want to produce based on the frequency of update. These buffers must also be of the same size.

  Buffer 1: Contains data for the sine wave of 1 KHz, 300 points 2 cycles of sine wave

  Buffer 2: Contains data for the sine wave of 1.5 KHz, 300 points, 3 cycles of sine wave

  You can Interleave them as before. When the data are performed through the ADC, they are out different sine waves, even if the AO channels are updated at the same speed.

• Overload CPU display with waveform graph

  My sample code (yahoo.vi) presents the 2D DBL in size of 30, 000 * 2 table.

  Whenever the 2D table was displayed with waveform graph, I found there were big delay (around seconds) by CPU overhead but the time was very short.

  Once this has happened, the computer (8108 PXI double heart, 4G of memory, 32-bit win7) has been slow to exploit something.

  Is it bug or problem comes from the computer? or do you have a solution?

  labmaster

  My version of LV is 2009.1 (service pack installed)

  You need to transpose the table! (or right click on the chart... convert table)

  You are graphing 30000 plots with two points each (hard!) instead of 2 plots with 30000 points each (easy!).

  (Imagine you would display the legend of the plot with 30000 plots, it would be a mile high!)

• Several channels with different frequencies

  Hello

  I use card NI USB-6221.

  The C API using, I need to generate 6 digital output channels, with frequencies of diffrenet and Heavy duty.

  To be more precise, the 2 are totally identical, but I need them to be reversed, and the other 4 are similar to another, but should be shifted in time (I.e. There is a delay between each of the channels).

  I used the 2 channels of CO that the USB-6221 takes charge for the first two signals, and it works very well (the two signals are synchronized and are reversed).

  Now I need an additional 4 channels for the other vague square.

  I saw an articale NOR by JohnP web site with the title:

  Generate multiple channels of digital output with different frequencies and Heavy Duty

  The following example shows how to create and generate a digital with the non-regeneration wave form so that you can change the frequency and the duty cycle on the fly with the M Series DAQ hardware X.  The example uses output digital rather than counters to achieve this, so if you need more output than the available counters, it would be a good option (Note: on the materials of the M series an external sample clock must be provided, this may be caused by one of the counters if you want).

  that seems to be exactly what I need, but the examples are for LabView which I did not.

  Can someone explain how to do this with the C functions?

  Best regards

  Danny.

  Hey Danny,

  The important thing to note is that you can clock of arbitrary digital waveform (up to 1 MHz on the 6221).  The real data acquisition programming is pretty easy once you have the waveform.  My Example LV used LabVIEW Base generating function VIand then converted to a digital waveform to generate the signal from each channel.

  The functions of LV helped tremendously with to achieve the waveforms to be updated on the fly (the basic function generator keeps track of phase for you).

  If you do not need to be updated on the fly, then the construction of the waveform in C should not be too bad.  For example:

  P0.0 [1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0] * 1

  P0.1 [0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0] * 2

  P0.2 [0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1] * 4

  P0.3 [1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1] * 8

  [9 9 9 9 9 3 3 3 3 3 6 6 6 6 6 12 12 12 12 12]

  The table above U8 would give you 4 output waveform of 50% duty cycle at Fs/20, shifted 90 degrees to eachother.  The lines would be p0.0 by p0.3 (the bit rate of the U8 corresponds to what line goes high).

  Best regards

• Wireless network is displayed with a cross and will not let me connect saying the settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again?

  hardware device

  my wireless network is displayed with a cross and will not let me connect saying settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again :(

  Hello

  What operating system installed on the computer?

  Note: Look for errors in the network card device manager.

  Method 1: Follow the article mentioned below, if you are using Windows 7 operating system.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  He looks at the IP address and other parameters are not set correctly, I suggest you contact your Internet service provider or provider router wireless to help on this.

  For more information, follow the below mentioned article:

  Set up a wireless router:

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Follow the below mentioned articles and see if they help you:

  Set up a wireless network:

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Wi - Fi and in Windows network connection issues:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Wireless network card: frequently asked questions:

  http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions

• Is it possible with us an axis in Max?

  Is it possible with us my axis Max?  I use a card PCI-7340.  I looked in the Interactive tab 1 d and I don't see an option to run a command of homers.

  No, direct debit is not implemented in MAX. Please use the API OR-Motion and LabVIEW, or any other programming language to run a movement of reference.

  Kind regards

  Jochen

• Using Vista Home Premium 64 x. In Windows Explorer how to group by name to display with the simple letters like A, B, C, D, etc. instead of A - H, P, Q - Z?

  Original title: group Windows Explorer by name

  Using Vista Home Premium 64 x.  In Windows Explorer how to group by name to display with the simple letters like A, B, C, D, etc. instead of A - H, P, Q - Z?  In XP, it could be sorted by simple letter, which makes it easier in a folder with many files.  Thanks in advance.

  Hi kmcmi,

   

  Welcome to Microsoft Answers Forums.

  Well this feature is not available in Windows Vista.

  It only works on Windows XP.

  I've added a useful link

  Behavior and change folder views

  http://windowshelp.Microsoft.com/Windows/en-us/help/3a3bfe59-5268-4FB3-81c5-7972c28939cd1033.mspx

  Hope this information is useful.

  Let me know if it worked.

  All the best!

  Thanks and greetings

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.